RENNSTALL MOTO RMC-010402 User manual

Brand: RENNSTALL MOTO

Model: RMC-010402

Type: User manual

RENNSTALL MOTO RMC-010402 clip-on handlebars transform your Triumph Speed Twin 1200, enhancing its handling and giving it a sportier, more aggressive stance. Experience precise steering and improved feedback, perfect for spirited riding on closed-course facilities or racetracks. These handlebars are designed for advanced riders seeking maximum control and performance from their motorcycle.

Clip Ons

for Triumph Speed Twin 1200

Part Number: RMC-010401 (without heated grips)

Part Number: RMC-010402 (with heated grips)

Instruction Manual

Version: 2

Date: 28.07.2021

Read and save this manual for future

reference. Before attempting to assemble,

install, operate the products, please

ensure a complete understanding of the

instructions and any other documents

related to the products, including but not

limited to a provided disclaimer. Failure to

comply with instructions in this manual

could result in serious injury, death and/or

property damage. This manual is subject

to change without notice.

Important note

Products of Rennstall Moto or any of its affiliates (collectively, "Rennstall")

are sold "AS IS" without any express or implied warranties. To the fullest

extent permitted by law, Rennstall disclaims any and all warranties.

Installation or usage of Rennstall's products may affect warranties of utilized

vehicles, such as motorcycles.

ANY BUYER OR USER OF PRODUCTS OF RENNSTALL EXPRESSLY AND

VOLUNTARILY ASSUMES ANY AND ALL RISKS INCLUDING, BUT NOT

LIMITED TO, DEATH, DISABILITY, AND/OR SERIOUS PHYSICAL INJURY,

RELATED TO THE INSTALLATION OR USAGE OF SUCH PRODUCTS BY

BUYER, USER OR ANY THIRD PARTY.

Under no circumstances are Rennstall's products to be used on public roads

or any other streets, highways, or off-road areas. Rennstall's products are

solely intended for use on vehicles operated on closed-course facilities,

show events or racetracks, each with appropriate supervision of qualified

individuals to ensure safety of all involved parties.

Always use caution when installing or using Rennstall's products, adhere to

all instructions, only utilize provided hardware or tools, and do not modify

or otherwise alter the products.

Prior to any usage of Rennstall's products, a buyer or user shall inspect and

verify the integrity of the entire vehicle upon which such products are

mounted, installed, or otherwise attached. Vehicles are to be inspected

before each use for evidence of damage, defect, or wear to ensure the

vehicle is fit and ready for operation. Without limiting the generality of the

foregoing, buyer or user shall specifically inspect all bolts after each usage

in excess of Two Hundred (200) kilometers per hour or One Hundred

Twenty-Five (125) miles per hour.

Under no circumstances and under no legal theory whether in tort, contract,

or otherwise shall Rennstall or its employees, agents, representatives,

successors, or assigns, be liable to a buyer, user or any other person for any

direct, indirect, special, incidental, or consequential damages of any kind

arising out of or relating to the installation or usage of the products,

even if Rennstall has been informed of the possibility of such

damages, or for any claim by any other party.

Clip Ons (page 1)

Part Number: RMC-010401 (without heated grips)

Part Number: RMC-010402 (with heated grips)

Time:

approx. 4h

Note:

Fitting clip on handlebars requires advanced

wrenching skills. We recommend to consult a

professional.

Disassembly Steps:

Remember headlight height/position.

(Tip: Switch the headlight on and mark the

border between light and dark on the wall with

a piece of tape.)

Remove the two M8 bolts either side of the

headlight. Be careful the headlight doesn‘t

drop down.

Remove mirrors and hand controls from the

handlebars.

Remove the instruments, keep the wires

connected.

If applicable cut open the wires of the heated

grips.

Remove original handlebars and riser adapter.

Remove the top triple tree and the headlight

bracket sleeves (careful not to lose the top and

bottom rubber rings).

Clip Ons (page 2)

Part Number: RMC-010401 (without heated grips)

Part Number: RMC-010402 (with heated grips)

Assembly Steps:

Install the new shortened headlight bracket sleeves. Do not forget the rubber

rings top and bottom.

Remove headlight brackets from the old sleeves and mount onto the new

shortened sleeves.

Install the clip ons and hand controls. Make sure nothing touches the tank at

full steering angle!

Install the top triple tree and torque the M8 bolts down to 25Nm (18.4 ft·lb).

If applicable reconnect the cables for the heated grips using the included

connector.

Instruments Lowering:

Position the two 35mm lowering spacers between the triple tree and the

instruments. Use the longer TX M6x50 bolts to fix in place.

If applicable install the front fairing.

Position the cylindrical spacers on the outside of the headlight brackets, the

side with the smaller diameter pointing towards the headlight.

(Tip: Hold spacers in place with some sealant or modeling clay.)

Fit the fairing and put the headlight back into position. Loosely insert the two

new TX M8 bolts and countersunk washers. Do not yet tighten.

Adjust the headlight height according to the marking on the wall you made

earlier. Now torque down the two TX M8 bolts to 18Nm (13.3 ft·lb).

Insert the cylindrical part of the “anti twist bracket“ into the underside of the

head tube. Use the long hole on the bracket to adjust the fairing angle and

torque the bolt down to 6Nm (4.4 ft·lb).

Fix the other side to the inside of the fairing using the TX M6x15 bolt,

countersunk washer and tooth nut. Torque down to 8Nm (5.9 ft·lb).

Install the brake fluid reservoir using the new bracket.

(Recommendation: Swap your reservoir for a smaller one.)

Make sure wires and cables are running correctly and don‘t rub anywhere.

RENNSTALL MOTO RMC-010402 User manual

RENNSTALL MOTO RMC-010402 User manual

RENNSTALL MOTO RMC-010402 User manual

Related papers

Other documents