FXLuminaire SRP-CC is a versatile strip light color controller compatible with SRP-RGBW Strip Light and various low-voltage transformers, including the EX Transformer, PX Transformer, DX Controller, and Luxor Controller. It offers two modes of operation: Standalone Mode, allowing for manual adjustment of Hue, Saturation, and Intensity, and Luxor Mode for integration with the Luxor Controller for advanced lighting control and grouping. Installation is simple, involving connecting the low-voltage wires to the transformer and securing the controller using the provided mounting hardware.
FXLuminaire SRP-CC is a versatile strip light color controller compatible with SRP-RGBW Strip Light and various low-voltage transformers, including the EX Transformer, PX Transformer, DX Controller, and Luxor Controller. It offers two modes of operation: Standalone Mode, allowing for manual adjustment of Hue, Saturation, and Intensity, and Luxor Mode for integration with the Luxor Controller for advanced lighting control and grouping. Installation is simple, involving connecting the low-voltage wires to the transformer and securing the controller using the provided mounting hardware.
Owner’s Manual and Installation Instructions
SRP-CC
Color Controller
for SRP-RGBW
Strip Light
1.68"/4.27 cm
4.01"/10.19 cm
E0000
AAA
7/22/2012
REV
ECO REVISION DESCRIPTION
DRFT
DATE
A
B
C
D
4
3
2
1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
COLOR:
MATERIAL
SPEC:
SCALE:
DRAWING NO.
REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
RGBW CUBE
KL
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2
1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
10/26/2021
DRAWN
BY:
PRODUCT:
MATERIAL:
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
C1 FORMAT REVISION 11/20/2017
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
https://fxl.help/srp
2
Table of Contents
Controller Overview
3 SRP-CC Components
Controller Installation
4 Controller Mounting
6 Setting Up Standalone Mode
7 Setting Up Luxor® Mode
3
Controller Overview
1.68"/4.27 cm
4.01"/10.19 cm
E0000
AAA
7/22/2012
REV
ECO REVISION DESCRIPTION
DRFT
DATE
A
B
C
D
4
3
2
1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
COLOR:
MATERIAL
SPEC:
SCALE:
DRAWING NO.
REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
RGBW CUBE
KL
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2
1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
10/26/2021
DRAWN
BY:
PRODUCT:
MATERIAL:
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
C1 FORMAT REVISION 11/20/2017
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
Display
Mode MODE button: Toggles SRP-CC between Luxor
Mode and Standalone Mode. Note: Standalone Mode
indicates that a standard, low-voltage transformer is
being used (e.g., EX Transformer, PX Transformer, etc.).
Select SEL button: Toggles between Hue, Saturation,
and Intensity when running in Standalone Mode.
Plus + button: Increases values. In Luxor Mode,
use this button to increase the Group number. In
Standalone Mode, use this button to increase Hue,
Saturation, or Intensity values.
Minus - button: Decreases values. In Luxor Mode,
use this button to decrease the Group number. In
Standalone Mode, use this button to decrease Hue,
Saturation, or Intensity values.
Low-Voltage Wires: The 3' (0.9 m) wires must be
installed to a low-voltage transformer.
SRP-CC Power Feed Cable: 10' (3 m) cable used to
connect the SRP-CC Strip Light Color Controller to
the SRP-RGBW Strip Light.
Plus (+) Button
Select (SEL)
Button
Mode Button
Minus (-)
Button
SRP-CC Power
Feed Cable
Low-Voltage Wires
HUE
SRP-CC Components
4
Controller Installation
The SRP-CC Strip Light Color Controller is
compatible with any low-voltage lighting
transformer, including the EX Transformer,
PX Transformer, DX Controller, and Luxor
Controller from FX Luminaire. It is compatible
only with the FX Luminaire SRP-RGBW
Strip Light.
To power the controller, connect its low-voltage
wires to the output (common and voltage taps)
of the low-voltage transformer.
Controller Mounting
1. Drill ⅛" (3 mm) pilot holes into the mounting surface,
insert anchors, and install screws into the anchors,
leaving approximately ⅛" of thread exposed. Mount
the controller.
2. Mark locations for the bottom anchors with a
permanent marker.
3. Remove the controller
from the wall. Drill bottom
anchor holes and install the
anchors.
4. To secure the controller
to the wall, place it back
on top of the anchors.
Install the screw(s) into the
anchors at the bottom of
the controller.
The SRP-CC display illuminates only if
the low-voltage transformer is supplying
output voltage (minimum 12 VAC).
E0000
AAA
7/22/2012
REV
ECO REVISION DESCRIPTION
DRFT
DATE
A
B
C
D
4
3
2
1
DIMENSIONAL
TOLERANCES:
REL.
DATE:
TITLE:
COLOR:
MATERIAL
SPEC:
SCALE:
DRAWING NO.
REV.
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
ALL DIMENSIONS ARE IN INCHES
DO NOT SCALE DRAWING
1:1
RGBW CUBE
KL
ANGLES:
±1°
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
D
A
B
4
3
2
1
SHEET 1 OF 1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
THIRD ANGLE PROJ.
C
SIZE:
2/9/2022
DRAWN
BY:
PRODUCT:
MATERIAL:
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
CONFIDENTIAL AND PROPRIETARY
C1 FORMAT REVISION 11/20/2017
DENOTES FUNCTIONALLY CRITICAL POINTS
DENOTES CRITICAL INSPECTION POINTS
5
SRP-RGBW Strip
Light Power Feed
Cable
SRP-CC Power
Feed Cable
SRP-RGBW
Power Feed Cable
Low-Voltage
Wires
Controller Installation
To power the SRP-RGBW Strip Light, connect the
SRP-CC power feed cable to the strip light power
feed cable.
Low-Voltage
Wires
SRP-RGBW
Power Feed Cable
HUE
SRP-CC Controller Installation
Luxor Mode
SRP-CC Controller Installation
Standalone Mode
GRP
6
Controller Installation Standalone Mode
Setting Up Standalone Mode
1. Attach the SRP-CC low-voltage wires to the output
taps or eld wires connected to the on-site low-
voltage transformer.
2. Turn on the low-voltage transformer manually to
conrm the output voltage is at least 12 VAC.
3. Conrm that the SRP-CC display is illuminated.
4. Verify that the Hue, Saturation, or Intensity are
displayed. This conrms that the SRP-CC is in
Standalone Mode.
5. If GRP (Luxor Mode) is displayed, press the
Mode MODE button to see the Hue, Saturation, or
Intensity values.
6. Once in Standalone Mode, the SRP-RGBW Strip
Light will illuminate according to the selected Hue,
Saturation, and Intensity values.
7. To toggle between Hue, Saturation, and Intensity,
press the Select SEL button. The current selection will
be displayed at the bottom of the screen.
8. Use the Plus + and Minus - buttons to adjust the
Hue, Saturation, and Intensity values.
a. Hue: 0 to 360
b. Saturation: 0 to 100
c. Intensity: 0 to 100
https://fxl.help/color
HUE
SAT
INT
Scan the QR code to
see suggested Hue and
Saturation values.
HUE
7
Controller Installation Luxor Mode
Setting Up Luxor Mode
1. Attach the SRP-CC low-voltage wires to the output
taps (Common and 15 V) or eld wires connected to
the on-site Luxor Controller.
2. Turn on the Luxor Controller manually to conrm the
output voltage is at least 12 VAC.
3. Conrm that the SRP-CC display is illuminated.
4. Conrm that GRP (Luxor Mode) is displayed at the
bottom of the screen.
5. If HUE, SAT, or INT is displayed, press MODE MODE to
show GRP. This conrms that the SRP-CC is in
Luxor Mode.
6. Once in Luxor Mode, the SRP-RGBW Strip Light will
be controlled using the Luxor Controller. Set GRP
to the desired group. Use + and - to adjust the
group number (1–250). The SRP-CC Controller and
SRP-RGBW Strip Light will only work with the Luxor
Controller if the assigned group is activated. This
xture should not be mixed with other xture group
numbers.
7. Program the color and intensity using the Luxor
Controller interface or Luxor App.
GRP
https://fxl.help/color
Note: The Select SEL button is not used in
Luxor Mode.
8
LANDSCAPE & ARCHITECTURAL LIGHTING
1940 Diamond Street, San Marcos, CA 92078
fxl.com FX-318-OM EN 2/22
https://fxl.help/install
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
FXLuminaire SRP-CC is a versatile strip light color controller compatible with SRP-RGBW Strip Light and various low-voltage transformers, including the EX Transformer, PX Transformer, DX Controller, and Luxor Controller. It offers two modes of operation: Standalone Mode, allowing for manual adjustment of Hue, Saturation, and Intensity, and Luxor Mode for integration with the Luxor Controller for advanced lighting control and grouping. Installation is simple, involving connecting the low-voltage wires to the transformer and securing the controller using the provided mounting hardware.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Luxor ZD Owner's manual
-
Hunter Industries LINKMOD Owner's manual
-
Kodak SRP 30 User manual
-
Juniper JUNOSE 10.0.3 - S 4-30-2010 Release note
-
Philips SRP3004 User manual
-
GRASS VALLEY DEC-1003 Installation and Operation Guide
-
Lumascape LUXOR User guide
-
-
-
Barco MDSC-2124 User guide