How Do You Program Your Scanner?
1.Scan Start Conguration
2.Scan all necessary able for parameters that
Meet your application
3.Scan end conguration to save to save the changes.
Resetting The Standard Product Defaults
If you aren’t sure what programming options are in your scanner,
or you’ve changed some options and want the factory settings
restored, scan the bar code below.
Symbologies setting
Terminator selection
Start Conguration
None * CR + LF
Tab CR
Interface selection
Reading mode
Language ………etc.
End Conguration
Standard Product
Default Setting
* US
LF
* Please scan the following barcode directly with your USB receiver on.
USB Keybaord Language
Itlian
Default setting of wireless scanner
The default setting of wireless scanner is 2425MHz and
power saving with 10min period of time. The default values
can be modied by re-pairing the scanner and USB receiver.
The setting switch and pairing button are located at USB
receiver as shown
Setting switch 1 is associated with
volume of beeper
Setting switch 2 is associated with
frequency
Setting switch 3 & 4 is associated
with power management
Note: Before congure the switch setting, please rst remove the
USB receiver from host computer.
How to pair your scanner and
receiver?
Scanner
USB receiver
** When devices are successfully paired you will hear beeps three
times from scanner and see three bllnks from USB receiver.
Wake up your Atlantis wireless
scanner
Press and release the trigger on your scanner to activate it.
Your scanner is ready to work when blue LED comes on.
Connect USB receiver to a host
computer
The device can be quickly recognized by host computer
without any software/driver installation. Within less than
10 seconds the receiver will double ash blue to inform the
Initialization is completed.
Recharging the battery
The Red LED comes on when the battery level is low, please
recharge the scanner immediately. When the scanner is
charging, the LED is green (solid). A full recharge (from
completely drained battery) takes approximately 4 hours.
When the scanner is fully charged, the green LED will go off.
Scanner LED indicator
USB receiver LED indicator
Before Getting Started
Open the package and check every accessory
About your Atlantis wireless scanner
KC-3200ZB is one on one wireless data communication
protocol. The scanner is already paired with the USB receiver. Just
easily plug USB receiver and start the operation. The
scanner on a real time basis, if the scanner is connected, the
barcode is decoded and transmitted to the remote host without
any delay. If the scanner is not connected or out of range, the data
is lost (status: 4 beeps)
Note:
New batteries should be fully charged before their rst use
Wireless Scanner
USB docking station
USB Receiver
USB recharge cable
Status / indicator
Good Scan
Transmission
failure
Low battery
Recharge
Operation mode
Sleeping
Color
Red
Beeper
1 beep
4 beeps
None
Indication
LED will ash to present the success of transmision
Blue LED
1 blink
On
None
Green LED
On
None
Red LED
On
Noe
#1
ON
OFF
Volume of beep
Low
High
#2
ON
OFF
Frequency
2480MHz
2425MHz
#3
OFF
ON
ON
OFF
#4
OFF
ON
OFF
ON
Power saving (sleep mode)
switch off after 10min.of inactivity
Scanner is always on
switch off after 30min.of inactivity
switch off after 1min. of in activity
In 1 second
In 5 second
In 2 second
In 1 second
In second
Press and hold the trigger for 10 sec. release the
trigger after hearing 1 beep
Piease quick press the trigger for 10 times
within five (5) sec. in order to put the scanner in
pairing mode.
The scanner will beep every second when stay in
paring mode (for about 45 seconds.)
Press and hold the pairing button for 10 sec.
release the button after seeing red LED ashing.
Please quick press the pair bottom for 10 times
within five (5) sec.in order to put the scanner in
pairing mode.
in pair mode, the USB receiver will blink every
second (for 25 xeconds)
2
3
4
5
6
1
/