Acrosser Technology AR-R6006 Owner's manual

Brand
Acrosser Technology
Model
AR-R6006
Category
Motherboards
Type
Owner's manual
Revision: 1.0
AR-B6006
Board Guide
1
Revision: 1.0
Copyright
All Rights Reserved.
Manual’s first edition:
For the purpose of improving reliability, design and function, the information in this
document is subject to change without prior notice and does not represent a commitment on
the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or documentation,
even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this Manual may be reproduced by any mechanical, electronic, or other
means in any form without prior written permission of the manufacturer.
Trademarks
AR-B6006 are registered trademarks of Acrosser; IBM PC is a registered trademark of the
International Business Machines Corporation; Atom™ is a registered trademark of Intel
Technologies Inc; Phoenix is a registered trademark of Phoenix Software International Inc;
other product names mentioned herein are used for identification purposes only and may be
trademarks and/or registered trademarks of their respective companies.
2
Revision: 1.0
Table of Contents
1. ...............................................................................................4 Introduction
1.1 ..............................................................................................4 Features
1.2 .......................................................................................5 Specification
1.3 ..............................................................................6 Package Contents
1.4 ....................................................................................7 Block Diagram
2. ...............................................................................8 Hardware Information
2.1 ........................8 Locations of IO ports & Jumper settings definition
3. ............................................................................................14 BIOS Setting
3.1 ..................................................................14 Main (System Overview)
3.2 ......................................................14 Advanced (Advanced Settings)
3.3 ....................................................................................................15 Intel
3.4 .............................................................................................15 Security
3.5 ........................................................................................16 HWMonitor
3.6 .................................................................................................16 Power
3.7 ...........................................................................17 Boot(Boot Setting)
3.8 .....................................................................................................17 Exit
Appendix.........................................................................................................18
Appendix A - Driver Installation and Programming Guide (Windows) .....18
A-1 GPIO and Watchdog............................................................................18
A-2 API List and Descriptions…………………………………………………19
Appendix B - Programming Guide (Linux)..................................................23
B-1 GPIO and Watchdog............................................................................23
B-2 API List and Descriptions…………………………..…………………….23
3
Revision: 1.0
4
1. Introduction
Welcome to the AR-B6006 series Computer. The AR-B6006 series is a Networking board for
Micro-box and Rack-mount with six sets of GbE LAN. Intel Atom (Pineview-D) D525 +ICH8M.
AR-B6006 is a Networking board for micro-box and Rack-mount Platform with Intel Atom D525
+ICH8M, 6 *10/100/1000 LAN with by-pass.
1.1 Features
Processor:
AR-B6006D525: Intel® Atom™ Processor D525 (Dual Core, 2X 512K L2 Cache, 1.8
GHz)
Chipset: Intel® ICH8M
Memory: DDR3 800/1333 MHz SO-DIMM, Maximum 4GB
Display: VGA
Storage: 1x CF, 3x SATA II
Communication: 6x Gbps Ethernet, 4x USB 2.0, 2x RS-232
General: Watchdog timer, 4-bit GPIO
Revision: 1.0
1.2 Specification
System
Thermal solution FAN connector for CPU FAN
Fan connector for system FAN*2
CPU Intel® Atom™ processor D525 (1M Cache, 1.8
GHz)
System Memory 204-pin DDR3 SO-DIMM socket x2 , DDR3 up
to 4GB, non-ECC and un-buffered
BIOS 1. Support console redirection (default enable)
2. Support bypass setting (default disable)
Phoenix
Legacy BIOS
ROM 1MB
System Chipset Intel ICH8M
Super I/O Winbond-W8627DHG-P
Network Interface
Ethernet 6 *RJ45
Intel 82574L (10/100/1000Mbps) (L1~L6),
LAN by-Pass LAN1 and LAN2 support by-pass function
LAN3 and LAN4 support by-pass function
Reserve 1*3 pin Jumper for Hardware select
bypass status
Default:
normal
Bypass
I/O
Front panel 1.Power /HDD/Bypass LED:
2.LAN1/ LAN2/ LAN3/ LAN4/LAN5/LAN6 LED:
1000, 10/100, Act.
Rear panel From left to right:
2 * USB (use standby power)
COM port (RJ45)
LAN6/LAN5/LAN4/ LAN3/ LAN2/LAN1
Internal I/O
1. 2xUSB 2.0(2.54 mm pitch)
2. Mini-PCI
3. GPIO
4. LPT pin head
5. Power input
6. KB/MS
7. VGA pin head
8.PWRSW
9. COM-2
Storage
CF 1 x Compact Flash socket
(Master mode) Support UDMA
SATA 3x SATAII interface with power x 1
Others
Watchdog Timer Software programmable 1~255 Seconds,
Battery Lithium Battery, 3V 220mAH (CR2032)
Hardware
monitoring
CPU voltage
CPU and System Temperature
OS support Fedora 14. 64-bit
Ubuntu 10.04 32-bit, Ubuntu 10.04 64-bit
WIN XP 32-bit,
5
Revision: 1.0
6
Mechanical
Dimension 210 mm x 140 mm
Operating
Temperature
0~60
o
C (32~140
o
F)
Storage
Temperature
-20~60
o
C (-4~176
o
F)
Relative
Humidity
10 to 95% @ 40°C, non-condensing
Power Supply N/A
Power
Requirements
24 Pin ATX Power Connector
BIOS Default setting
After power failure [Power On]
1.3 Package Contents
Description Q’ty
AR-B6006 Mainboard
1
Driver CD
1
Quick User Manual
1
Console Cable (P/N:190030627-G)
1
VGA Cable
1
Revision: 1.0
1.4 Block Diagram
7
Revision: 1.0
2. Hardware Information
2.1 Locations of IO ports & Jumper settings definition
8
4 3 5
13
15
14
16
11 12
10
9 8 7 6
17
18
1
25
2
24
23 2122 20 19
Revision: 1.0
Item Name Description
1 Mini PCI 124 pin mini PCI connector
2
J4（LED
Board）
Pin Description
1 3.3V
2 GND
3 3.3V
4 GND
3
J1(GPIO
)
Pin Description Pin Description
1 5v 2 12v
3 GPIO17 4 GPIO20
5 GPIO18 6 GPIO37
7 GND 8 GND
More Detail please see Note.2
4 PWRSW
Pin Description
1 Power button +
2 Power button -
3 Reset +
4 Reset -
5 ATX ATX 20P female connector
6 JUSB
Pin Description Pin Description
1 VCC 2 VCC
3 -DATA2 4 -DATA3
5 +DATA2 6 +DATA3
7 GND 8 GND
9 NULL 10 GND
9
Revision: 1.0
7
CPU
FAN
8
SYS
FAN1
9
SYS
FAN2
10
So-DIM
M
DDR3 SO-DIMM socket
11 CF Card
Compact Flash socket
12 VGA
Pin Description Pin Description
1 R 2 GND
3 VCC 4 G
5 GND 6 DDCDA
7 B 8 GND
9 HSYNC 10 VCC
11 VCC 12 VSYNC
13 GND 14 GND
15 DDCCK 16 NC
10
Revision: 1.0
13 LPT
Pin Description Pin Description
1 STB 2 AFD
3 D0 4 ERR
5 D1 6 INIT
7 D2 8 SLIN
9 D3 10 GND
11 D4 12 GND
13 D5 14 GND
15 D6 16 GND
17 D7 18 GND
19 ACK 20 GND
21 BUSY 22 GND
23 PE 24 GND
25 SLCT 26 GND
14 COM 2
Pin Description Pin Description
1 DCD 2 RXD
3 TXD 4 DTR
5 GND 6 DSR
7 RTS 8 CTS
9 RI 10 NULL
15
IDE
PWR
4P male power connector
16 SATA Standard SATA connector
17 J5
Pin rip cripDesc tion Pin Des tion
1 KB_DAT _DAA 2 MS TA
3 _CLK S_CLKB 4 M K
5 GND 6 GND
7 VCC 8 VCC
11
Revision: 1.0
Pin De Pin De scription scription
1 A
ED
2 VCC L N1_LINK/ACTIVE#_L
3 A 4 A
D
L N1_LINK1000#_LED L N1_LINK100_LE
5 A
ED
6 VCC L N2_LINK/ACTIVE#_L
7 A 8 LA
ED
L N2_LINK1000#_LED N2_LINK100#_L
18 LAN LED
9 A
ED
L N3_LINK/ACTIVE#_L
10 VCC
11 A 2 A
ED
L N3_LINK1000#_LED 1 L N3_LINK100#_L
13 A
ED
L N4_LINK/ACTIVE#_L
14 VCC
15 A 6 A
ED
L N4_LINK1000#_LED 1 L N4_LINK100#_L
19 USB USB type A connector
20
PWR/HD
LED
Pin Description
1 HDD ED _L +
2 HDD ED _L -
3 PWR ED+ _L
4 PWR ED _L -
21 J6
1- 2PIN，Auto Power ON；2-3PIN，Manual Power On
Default setting : 1-2 Auto Power on
22 JCMOS
Pin 1-2 2-3
Define Normal Clear cmos
Default 1-2 Normal
23
J3（WDT
Select）
1- 2PIN，Watchdog Control System Reset；
2- 2-3PIN，Watchdog Control BYPASS
Default :2-3 Watchdog Control Bypass
24 LAN RJ45 connector
12
Revision: 1.0
13
25
Bypass
LED
Pin rip cripDesc tion Pin Des tion
1 VCC 2 BYPASS1-N
3 VCC 4 PASSBY 1
5 VCC 6 BYPASS2-N
7 VCC 8 PASSBY 2
9 ULL 0 NC N 1
Note.1 It can not use USB Hub with power adaptor that connects to USB port.
Note.2 Appendix A GPIO Mapping table
GPIO17 ------ Output Default Low
GPIO18 ------ Output Default Low
GPIO20 ------ Output Default Low
GPIO37 ------ Output Default Low
GPIO Base Address: 0x1180
GPIO17 Enable GPIO17: 0x1182 bit1 1: Enable
GPIO17 Input/output Select: 0x1186 bit1 0: Output 1: Input
GPIO17 Level: 0x118E bit1
GPIO18 Enable GPIO18: 0x1182 bit2 1: Enable
GPIO18 Input/output Select: 0x1186 bit2 0: Output 1: Input
GPIO18 Level: 0x118E bit2
GPIO20 Enable GPIO20: 0x1182 bit4 1: Enable
GPIO20 Input/output Select: 0x1186 bit4 0: Output 1: Input
GPIO20 Level: 0x118E bit4
GPIO37 Enable GPIO37: 0x11B0 bit5 1: Enable
GPIO37 Input/output Select: 0x11B4 bit5 0: Output 1: Input
GPIO37 Level: 0x11B8 bit5
Revision: 1.0
3. BIOS Setting
3.1 Main (System Overview)
The BIOS setup main menu includes some options. Use the [Up/Down] arrow key to highlight the
option that you wish to modify, and then press the [Enter] key to select the item and configure the
functions.
3.2 Advanced (Advanced Settings)
The <Advanced > menu consists of configuration entries that allow you to improve your system
performance, or let you modify some system features according to your preference. Some entries
are required and reserved by the board’s design.
14
Revision: 1.0
3.3 Intel
Use the Intel BIOS menu to access the CPU and ICH(southbridge) configuration menus.
3.4 Security
The BIOS provides a Supervisor and a User password. If you use both passwords, the Supervisor
password must be set first.
15
Revision: 1.0
3.5 HWMonitor
This section shows the parameters in determining the Hardware Monitor Status. These parameters
include temperatures, fan speeds, and voltages.
3.6 Power
This option determines the configuration of power management.
16
Revision: 1.0
3.7 Boot(Boot Setting)
This option allows user to select sequence/priority of boot device(s).
3.8 Exit
This option is use to exit the BIOS main menu and change password.
17
Revision: 1.0
Appendix
Appendix A - Driver Installation and Programming Guide (Windows)
A-1 GPIO and Watchdog
Overview
AR-B6006 provides both a GPIO interface and a Watchdog timer. Users can use the GPIO and
Watchdog APIs to configure and to access the GPIO interface and the Watchdog timer. The GPIO
has four input pins and four output pins. The Watchdog timer can be set to 1~255 seconds. Setting
the timer to zero disables the timer. The remaining seconds of the timer to reboot can be read from
the timer.
In this GPIO and Watchdog package, we provides:
1. API Library.
2. GPIO and Watchdog test tool and the tool source code.
Driver Installation
Super I/O Driver Folder
Click the file SetupDriver.exe to install Super I/O driver.
18
Revision: 1.0
(Driver installation completely)
Files Description
SuperIoAPI.h: This file contains all define values and structures, it should be included in your
application program source code.
SuperIoAPI.lib: This file contains all API functions library, it’s for static linking with your application
program source code.
SuperIoAPI.dll: This file contains all API functions library, it’s for dynamic linking with your application
program source code.
A-2 API List and Descriptions
GPIO and Watchdog
GPIO
Notice: Before using GPIO
APIs, be sure Super I/O driver has installed successfully.
GPIO pins defines below:
#define GPO_BIT_17 17
#define GPO_BIT_18 18
#define GPO_BIT_20 20
#define GPO_BIT_37 37
#define LED1 GPO_BIT_17
#define LED2 GPO_BIT_20
#define LED3 GPO_BIT_18
#define LED4 GPO_BIT_37
BOOL WINAPI SuperIo_Open();
Remarks:
You must call this function at start-up of application to open Super I/O device.
19
Revision: 1.0
Parameters:
( None )
Return Value:
Returns TRUE on success.
If the Super I/O driver has not installed, return FALSE.
void WINAPI SuperIo_Close();
Remarks:
You must call this function at end of application to close Super I/O device.
Parameters:
( None )
Return Value:
( None )
BOOL WINAPI Gpio_GetBitValue( int nBit, BYTE* pValue );
Remarks:
Call this function to get GPIO pins value.
Parameters:
nBit
Stand for GPIO pins, you can assign value LED1 ~ LED4, or value GPO_BIT_17,
GPO_BIT_18, GPO_BIT_20, GPO_BIT_37.
pValue
Pointer of variable to retrieve GPIO pins state.
Return Value:
Returns TRUE on success, FALSE on failure.
BOOL WINAPI Gpio_SetBitValue( int nBit, BYTE bValue );
Remarks:
Call this function to Set GPIO pins value.
Parameters:
nBit
Stand for GPIO pins, you can assign value LED1 ~ LED4, or value GPO_BIT_17,
GPO_BIT_18, GPO_BIT_20, GPO_BIT_37.
bValue
Output value of GPIO pins, value 1 or 0.
Return Value:
Returns TRUE on success, FALSE on failure.
Watchdog
Notice: Before using GPIO
APIs, be sure Super I/O driver was installed successfully.
20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Acrosser Technology AR-R6006 Owner's manual

Brand
Acrosser Technology
Model
AR-R6006
Category
Motherboards
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents