Alto SR800SA Owner's manual

Category
Subwoofers
Type
Owner's manual

This manual is also suitable for

Alto SR800SA is a 15" compact subwoofer active speaker cabinet that delivers powerful and precise sound reinforcement for a variety of applications. With its 400W continuous power handling capability, it produces a frequency response of 42Hz-125Hz (-10dB) and a maximum SPL of 125dB. Equipped with a 15" woofer and an HPF 80Hz under analog processor, it provides deep, controlled bass for music and sound reinforcement systems.

Alto SR800SA is a 15" compact subwoofer active speaker cabinet that delivers powerful and precise sound reinforcement for a variety of applications. With its 400W continuous power handling capability, it produces a frequency response of 42Hz-125Hz (-10dB) and a maximum SPL of 125dB. Equipped with a 15" woofer and an HPF 80Hz under analog processor, it provides deep, controlled bass for music and sound reinforcement systems.

ACTIVE MODELSPASSIVE/
OWNER'S MANUAL
www.altoproaudio.com
Version 1.0 Apr 2009
English
SPEAKER ENCLOSURE
SR400P/SR800SA
c
All rights reserved to ALTO. All features and content might be changed
without prior notice. Any photocopy, translation, or reproduction of part of this
manual without written permission is forbidden. Copyright 2009 Seikaku Group
SEIKAKU TECHNICAL GROUP LIMITED
NO. 1, Lane 17, Sec. 2, Han Shi West Road, Taichung 40151, Taiwan
www.altoproaudio.com Tel: 886-4-22313737
email: [email protected] Fax: 886-4-22346757
NF00000-1.0
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT SAFETY INSTRUCTION
TO REDUCE THE RISK OF ELECTRIC SHOCK
PLEASE DO NOT REMOVE THE COVER OR
THE BACK PANEL OF THIS EQUIPMENT.
THERE ARE NO PARTS NEEDED BY USER
INSIDE THE EQUIPMENT. FOR SERVICE,
PLEASE CONTACT QUALIFIED SERVICE
CENTERS.
WARNING
To reduce the risk of electric shock
and fire, do not expose this equipment
to moisture or rain.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Dispose of this product should
notbeplacedinmunicipalwaste
and should be separate collection.
11.
12.
Move this Equipment only with a cart,
stand, tripod, or bracket,
specified by the
manufacturer, or
sold with the
Equipment. When
a cart is used, use
caution when
moving the cart /
equipment
combination to
avoid possible
injury from tip-over.
Permanent hearing loss may be caused by
exposure to \ extremely high noise levels.
The US. Government's Occupational Safety
and Health Administration (OSHA) has
specified the permissible exposure to noise
level.
These are shown in the following chart:
HOURS X DAY
EXAMPLE
According to OSHA, an exposure to high SPL in
excess of these limits may result in the loss of
heat. To avoid the potential damage of heat, it is
recommended that Personnel exposed to
equipment capable of generating high SPL use
hearing protection while such equipment is
under operation.
8
6
4
3
2
1,5
1
0,5
0,25 or less
SPL
90
92
95
97
100
102
105
110
115
Small gig
train
Subway train
High level desktop monitors
Classic music concert
Rock concert
This symbol, wherever used, alerts you to the
presence of un-insulated and dangerous voltages
within the product enclosure. These are voltages that
may be sufficient to constitute the risk of electric
shock or death.
This symbol, wherever used, alerts you to
important operating and maintenance instructions.
Please read.
Protective Ground Terminal
AC mains (Alternating Current)
Hazardous Live Terminal
ON: Denotes the product is turned on.
OFF: Denotes the product is turned off.
The apparatus shall be connected to a mains
socket outlet with a protective earthing
connection.
The mains plug or an appliance coupler is used
as the disconnect device, the disconnect device
shall remain readily operable.
CAUTION
Describes precautions that should be observed to
prevent damage to the product.
Read this Manual carefully before operation.
Keep this Manual in a safe place.
Be aware of all warnings reported
with this symbol.
Keep this Equipment away from water and
moisture.
Clean it only with dry cloth. Do not use
solvent or other chemicals.
Do not damp or cover any cooling opening.
Install the equipment only in accordance with
the Manufacturer's instructions.
Power Cords are designed for your safety. Do
not remove Ground connections! If the plug
does not fit your AC outlet, seek advice from
a qualified electrician. Protect the power
cord and plug from any physical stress to
avoid risk of electric shock. Do not place
heavy objects on the power cord. This could
cause electric shock or fire.
Unplug this equipment when unused for long
periodsoftimeorduringastorm.
Refer all service to qualified service personnel
only. Do not perform any servicing other than
those instructions contained within the
User's Manual.
To prevent fire and damage to the product,
use only the recommended fuse type as
indicated in this manual. Do not short-circuit
the fuse holder. Before replacing the fuse,
make sure that the product is OFF and
disconnected from the AC outlet.
1. INTRODUCTION
IN THIS MANUAL:
Thank you very much for expressing your confidence in LTO products by
purchasing SR800SA/SR400P speaker system. The SR series cabinets are
specifically designed for using in hi-quality performance site and the precise
sound reinforcement commercial place. uses trapezium configuration which
greatly decreases the resonance of the standing wave in the cabinet. These
cabinets uses hi-density matrix spraypaint technics and the bottom bracket
design which make mounting quickly and flexibly. The HF compression driver
and vented LF for fully professional performance.
Enjoy your SR800SA/SR400P speaker cabinet and make sure to read this manual
carefully before operation.
2. SPEAKER CABINET QUICK START
2
1. INTRODUCTION
1
The SR800SA/SR400P speaker cabinets include traditional amplifier module
which with separate AC transformer secondaries, power supplies and protection
systems.
8. WARRANTY
8
7
7. TECHNICAL SPECIFICATION
6
6. PANEL DESCRIPTION-SR400P
5
5. PANEL DESCRIPTION-SR800SA
3. WIRE CONNECTIONS
3
4
4. FREQUENCY RESPONSE
1
8.WARRANTY
1. WARRANTY REGISTRATION CARD
To obtain Warranty Service, the buyer should first fill out and return the encl-
osed Warranty Registration Card All the
information presented in this Warranty Registration Card gives the manuf-
acturer a better understanding
Please fill out all the infor-
mation carefully and genuinely, miswriting or absence of this card will void your
warranty service.
within 10 days of the Purchase Date.
of the sales status, so as to purport a more
effective and efficient after-sales warranty service.
2. RETURN NOTICE
2.1In
case of return for any warranty service, please make sure that the pr-
oduct is well packed in its original shipping carton, and it can protect your
unit from any other extra damage.
2.2
Please provide a copy of your sales receipt or other proof of purchase with
the returned machine, and give detail
2.3 A brief description of the defect will be appreciated.
2.4 Please prepay all the costs involved in the return shipping, handling and
insurance.
3. TERMS AND CONDITIONS
3.1 warrants that this product will be free from any defects in mat-LT O
erials and/or workmanship for a period of 1 year from the purchase date if
you have completed the Warranty Registration Card in time.
3.3 During the warranty service, may repair or replace this product atLT O
its own option at no charge to you for parts or for labor in accordance with
the right side of this limited warranty.
3.4 This warranty does not apply to the damages to this product that
occurred as the following conditions:
Instead of operating in accordance with the user's manual thoroughly, any
abuse or misuse of this product.
Normal tear and wear.
The product has been altered or modified in any way.
Damage which may have been caused either directly or indirectly by another
3.5 In no event shall be liable for any incidental or consequentialdamages.LT O
Some states do not allow the exclu-sion or limitation of incidental or conse-
quential damages, so the above exclusion or limitation may not apply to you.
3.6 This warranty gives you the specific rights, and these rights are
compatible with the state laws, you may also
have other statutory rights that may vary from state to state.
3.2 The warranty service is only available to the original consumer, who purch-
ased this product directly from the retail dealer, and it can not be transferred.
8
SPOTLIGHT
Make all initial connections with all the equipment powered off, and ensure
that all the main volume controls are turned completely down.
1). Connect one side of the signal cable at your audio mixer into output
left /right (with Stereo-Jack or XLR) and the other side of the cable into
the line input (Stereo-Jack) of your active speaker cabinet.
2). Connect the power cord to mains.
3). Turn on your mixer first, then the active speaker cabinets.
4). Turn up the volume control of the active speaker cabinets.
5). Use PFL function to get the proper input level for the mixer, and adjust
the main mix level control to manipulate the output level.
6). After using, turn off your active speaker cabinets first, then the mixer.
2. SPEAKER CABINET QUICK START
Left
Main Mix
Output
Signal Cable
Mixer
Right
Main Mix
Output
Signal Cable
SR800SA SR800SA
SR400PSR400P
2
15" Compact subwoofer Active Speaker Cabinet
400W in AES Standard
42Hz-125Hz (-10dB)
122dB Continuous / 125dB Peak (Calculated)
15" Woofer, 3" High Power voice coil
HPF 80Hz under analog processor
LINE-COMBO/LINK-XLR-M, OUT SAT with SPK NL-4
Line 0dBu
Volume SUB / Volume SAT / Phase NORMAL-REVERSE / Power
ON with Green LED / Clip Limiter with Red LED / Ground Lift
120-240 Volt, in Switching Power mode.
18mm multi-layer Plywood , glued and reinforced, black-scratch
resistant paint, metal grille and rubber footer foot, four
optional wheel
One standard metal pole-mount , plus one metal handle.
591x 451 x 554mm (23.27" x 17.76" x 21.81")
39.8 kg / 87.74 lbs
43.4 kg / 95.68 lbs
SR800SA
Power System
Frequency Response
Maximum SPL @ 1m
Transducer Low
Active Crossover
Input / Output
Input Level
External Control
Power Supply
Enclosure Construction
Mounting
Dimensions (HxWxD)
Net Weight
Shipping Weight
SPOTLIGHT
7. TECHNICAL SPECIFICATION
SR400P
Power System
Frequency Response (-10dB)
Sensitivity (1w @ 1mt)
Impedance:
Maximum SPL @ 1m
Coverage (HXV)
Transducer Low
Transducer High
Horn Type
Passive Crossover
Input Connector
Enclosure Construction
Mounting / Suspension
Dimensions (HxWxD)
Net Weight
Shipping weight
12" 2-way Passive Speaker Cabinet
400W Continuous in AES Standard
47Hz-20kHz (-10dB)
94dB SPL
4 (nominal)
122dB Continuous / 125dB Peak (Calculated)
90 x 45 nominal
12" Woofer, 2.5" High Power voice coil
1" Driver with 1.4" voice coil, Titanium Diaphragm
Eliptical Waveguide
2kHz at 12dB/oct with Electronic Protection
INPUT / THRU with SPK NL-4
Trapezoidal shape, 15mm multi-layer Plywood , black-scratch
resistant paint, metal grille and footer foot.
One metal pole-mount , two metal handle
615 x 377.5 x 377.8mm (24.21" x 14.86 x 14.87")
16.83 kg / 37.11 lbs
19.13 kg / 42.17 lbs
7
Speaker Cable
(14 AWG)
Speaker Cable
(14 AWG)
3 WIRE CONNECTIONS.
-.For Active Speaker Cabinets
As to these circumstances,audio connections is mostly intended for the signal
flow,so,determine the wire configuration according to your real application
system and its connecting facility.Normally,you have the following choices:
1+
2+
1-
2-
Please use the power connectors to make connections with other signal source
equipment for the passive speaker cabinets. The power connector has four terminals:
1+, 1-, 2+, 2-.
only
In our cabinets, only 1+/1- are used to connect the Speaker+/Speaker-, and 2+/2-
are not used.
-.For Passive Speaker Cabinets
6. PANEL DESCRIPTION-SR400P
SPOTLIGHT
CONNECTION PLATE
PASSIVE FULL RANGE: SR400P
(1) INPUT
(2) THRU
Receive the signal coming from an external power amplifier.
(SPK +1/-1 connected; +2/-2 not connected)
Direct LINK for connect in parallel a second speaker cabinet.
(SPK +1/-1 connected; +2/-2 not connected)
Besides, the passive crossover included the electronic protection
on the driver.
POWER HANDLING: 400W-AES Std.
IMPEDANCE: 4 Ohm
Max SPL: 122dB at 1mt
SOUND REINFORCEMENT SPEAKER SYSTEM
LINK
DESIGNED AND DEVELOPMENT IN ITALY
SERIAL
MODEL
INPUT
THRU
SR400P
36
(1) (2)
4. FREQUENCY RESPONSE
SR800SA
+60
+110
+70
+80
+90
+100
d
B
S
P
L
20 20k50 100 200 500 1k 2k 5k 10k
Hz
SR400P
+60
+110
+70
+80
+90
+100
d
B
S
P
L
20 20k50 100 200 500 1k 2k 5k 10k
Hz
ACTIVE SUBWOOFERS: SR800SA
5. PANEL DESCRIPTION-SR800SA
SPOTLIGHT
(10) VOLUME control of the satellite
(8)
(9)
(11) SIGNAL/LIMIT, Red LED, indicate ON status of the satellite
PHASE SWITCH reverse the polavity of the subwoofer output
(4)
(5)
LINE IN RIGHT.ON XLR CONNECTOR
Ground Lift Switch
SIGNAL/LIMIT, Red LED, indicate ON status of the subwoofer output
VOLUME control of the subwoofer output
POWER, Green LED, indicate ON status
AC power socket with main fuse
ON-OFF main power switch
(6)
LINE IN LEFT/MONO ON COMBO CONNECTOR
(7)
(3)
(12) Speaker output, Speakon to satellite 1+POSITIVE/1-NEGATIVE
Use only with a 250V fuse
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8) (11)
(12)
(9)
(10)
4 5
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Alto SR800SA Owner's manual

Category
Subwoofers
Type
Owner's manual
This manual is also suitable for

Alto SR800SA is a 15" compact subwoofer active speaker cabinet that delivers powerful and precise sound reinforcement for a variety of applications. With its 400W continuous power handling capability, it produces a frequency response of 42Hz-125Hz (-10dB) and a maximum SPL of 125dB. Equipped with a 15" woofer and an HPF 80Hz under analog processor, it provides deep, controlled bass for music and sound reinforcement systems.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI