Omega iDR and iDR-AL Owner's manual

Brand: Omega

Model: iDR and iDR-AL

Category: Recording Equipment

Type: Owner's manual

User’s Guide

Shop on line at

USA

MADE IN

omega.com

e-mail: [email protected]

iSeries info:

omega.com/specs/iseries

For latest product manuals

omegamanual.info

iDR Monitor

iDR-AL Limit Alarm

Temperature & Process DIN Rail

It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply.

OMEGA is constantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark

to every appropriate device upon certification.

The information contained in this document is believed to be correct but OMEGA Engineering, Inc. accepts no liability for any

errors it contains, and reserves the right to alter specifications without notice.

WARNING: These products are not designed for use in, and should not be used for, patient connected applications.

This device is marked with the international caution symbol. It is important to read the Setup Guide before installing or

commissioning this device as it contains important information relating to safety and EMC.

Servicing North America:

USA: One Omega Drive, P.O. Box 4047

ISO 9001 Certified Stamford CT 06907-0047

 TEL: (203) 359-1660 FAX: (203) 359-7700

 e-mail: [email protected]

Canada:;  976 Bergar

 Laval (Quebec) H7L 5A1

 TEL: (514) 856-6928 FAX: (514) 856-6886

 e-mail: [email protected]

For immediate technical or application assistance:

USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA

 Customer Service: 1-800-622-2378 / 1-800-622-BEST

 Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN

Mexico and  TEL: (001)800-TC-OMEGA

 FAX: (001) 203-359-7807

Latin American: En Espa

ñol: (001) 203-359-7803

 e-mail: [email protected]

Servicing Europe:

Czech Republic: Frystatska 184, 733 01 Karviná

 TEL: +420 59 6311899 FAX: +420 59 6311114

 e-mail: [email protected]

Germany/Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany

 TEL: +49 7056 9398-0 FAX: +49 7056 9398-29

 Toll Free in Germany: 0800 639 7678

 e-mail: [email protected]

United Kingdom: One Omega Drive

ISO 9002 Certified River Bend Technology Centre

 Northbank, Irlam Manchester M44 5BD United Kingdom

 TEL: +44 161 777 6611 FAX: +44 161 777 6622

 Toll Free in England: 0800 488 488

 e-mail: [email protected]

OMEGAnet

On-Line Service

www.omega.com

Internet e-mail

[email protected]

TABLE OF CONTENTS

Part 1: Introduction............................................................................................2

1.1 Description .................................................................................2

1.2 Safety Considerations ...............................................................3

1.3 Before You Begin .......................................................................4

Part 2: Setup.......................................................................................................5

2.1 Optional Remote Programmer Front Panel .............................5

2.2 Front Panel Connections...........................................................6

2.3 Electrical Installation .................................................................7

2.3.1 Power Connections........................................................7

2.3.2 Thermocouple - Input Connection................................8

2.3.3 Two / Three / Four Wire RTD-Hookups.........................9

2.3.4 Process Current - Wiring Hookup...............................10

2.3.5 Process Voltage - Wiring Hookup...............................10

2.3.6 Wiring Outputs - Wiring Hookup.................................11

Part 3: Operation: Configuration Mode..........................................................11

3.1 Introduction ..............................................................................11

Turning your Instrument On for the First Time

Buttons Functions in Configuration Mode

3.2 Menu Configuration ................................................................15

3.2.1 ID Number .....................................................................16

3.2.2 Setpoints .......................................................................17

3.2.3 Configuration Menu ....................................................18

3.2.4 Input Type Menu ...........................................................19

Input Type (Thermocouple) ........................................20

Input Type (RTD)...........................................................21

Input Type (Process) ...................................................22

3.2.5 Reading Configuration Menu .....................................23

3.2.6 Alarm 1 Menu ...............................................................27

3.2.7 Alarm 2 Menu................................................................31

3.2.8 Reading Adjust Menu...................................................32

3.2.9 Setpoint Deviation Menu/Field Calibration ................33

3.2.10 ID Code Menu ...............................................................34

3.2.11 Communication (Options) Menu.................................36

3.2.12 Display Color Selection Menu.....................................43

Part 4: Specifications ......................................................................................46

Part 5: Factory Preset Values .........................................................................49

CE APPROVAL INFORMATION .......................................................................50

LIST OF FIGURES:

Figure 2.1 Optional Remote Programmer Front Panel Display ...............5

Figure 2.2 Front Panel Connections...........................................................6

Figure 2.3 Main Power Connections ..........................................................7

Figure 2.4 Thermocouple Wiring Hookup..................................................8

Figure 2.5 Two/Three/Four-Wire RTD Wiring Hookup

a) RTD-1000 ohm/RTD-500 ohm..............................................9

b) RTD-100 ohm ........................................................................9

Figure 2.6 Process Current Wiring Hookup

(Internal and External Excitation) ...........................................10

Figure 2.7 Process Voltage Wiring Hookup

(With Sensor Excitation and without Sensor Excitation) .....10

Figure 2.8 Output Wiring Hookup

a) Mechanical Relay and SSR Outputs.................................11

b) Pulse and Analog Outputs.................................................11

Figure 2.9 Snubber Circuit Wiring Hookup..............................................11

Figure 2.10 Typical Wiring...........................................................................12

Figure 2.11 Communication Output Wiring Hookup

a) RS-232 Output ....................................................................13

b) RS-485 Output ....................................................................13

Figure 2.12 Excitation Output .....................................................................13

Figure 2.13 Embedded Ethernet .................................................................13

Figure 3.1 Flow Chart for ID and Setpoints .............................................15

Figure 3.2 Flow Chart for Configuration Menu........................................18

Figure 3.3 Flow Chart for Input Type Menu .............................................19

Figure 3.4 Flow Chart for Reading Configuration ...................................23

Figure 3.5 Flow Chart for Alarm 1.............................................................27

Figure 3.6 Flow Chart for Alarm 2.............................................................31

Figure 3.7 Flow Chart for Reading Adjust................................................32

Figure 3.8 Flow Chart for Setpoint Deviation/Field Calibration .............33

Figure 3.9 Flow Chart for ID Code ............................................................34

Figure 3.10 Flow Chart for Communication Option ..................................36

Figure 3.11 Flow Chart for Display Color Selection..................................43

LIST OF TABLES:

Table 2.1 Front Panel Annunciators...........................................................5

Table 2.2 Connectors...................................................................................6

Table 2.3 Power Connections .....................................................................7

Table 2.4 TC Wire Color Chart ....................................................................8

Table 3.1 Button Function in Configuration Mode..................................14

Table 3.2 Conversion Table.......................................................................26

Table 4.1 Input Properties .........................................................................48

Table 5.1 Factory Preset Values ...............................................................49

NOTES, WARNINGS and CAUTIONS

Information that is especially important to note is identified by following labels:

• NOTE

• WARNING or CAUTION

• IMPORTANT

NOTE: Provides you with information that is important to successfully

setup and use the Programmable Digital Meter.

CAUTION or WARNING: Tells you about the risk of electrical shock.

CAUTION, WARNING or IMPORTANT: Tells you of circumstances or

practices that can effect the instrument’s functionality and must refer

to accompanying documents.

TIP: Provides you helpful hints.

PART 1

INTRODUCTION

1.1 Description

This device can be purchased as monitor (read process value only), limit

alarm with alarm menu but no PID control (specify -AL option), or as a

controller.

• The iSeries offers unparalleled flexibility in process measurement. Each unit

allows the user to select the input type, from 10 thermocouple types (J, K, T,

E, R, S, B, C, N and J DIN), Pt RTDs (100, 500 or 1000 Ω, with either 385 or

392 curve), DC voltage, or DC current. The voltage/current inputs are fully

scalable to virtually all engineering units, with selectable decimal point,

perfect for use with pressure, flow or other process input.

• Options include programmable RS-232 or RS-485 serial communication and

ethernet with an embedded web server. Analog Output is fully scalable and

may be configured as a proportional controller or retransmission to follow

your display. Universal power supply accepts 90 to 240 Vac. Low voltage

power option accepts 24 Vac or 12 to 36 Vdc.

• The optional Remote Programmer features a large, three color

programmable display with capability to change a color every time the Alarm

is triggered.

1.2 Safety Considerations

This device is marked with the international caution symbol. It is important

to read this manual before installing or commissioning this device as it

contains important information relating to Safety and EMC

(Electromagnetic Compatibility).

This instrument is a panel mount device protected in accordance with

EN 61010-1:2001, electrical safety requirements for electrical equipment

for measurement, control and laboratory. Installation of this instrument

should be done by qualified personnel. In order to ensure safe operation,

the following instructions should be followed.

This instrument has no power-on switch. An external switch or circuit-

breaker shall be included in the building installation as a disconnecting

device. It shall be marked to indicate this function, and it shall be in close

proximity to the equipment within easy reach of the operator. The switch or

circuit-breaker shall meet the relevant requirements of IEC 947–1 and

IEC 947-3 (International Electrotechnical Commission). The switch shall

not be incorporated in the main supply cord.

Furthermore, to provide protection against excessive energy being drawn

from the main supply in case of a fault in the equipment, an overcurrent

protection device shall be installed.

• Do not exceed voltage rating on the label located on the top of the

instrument housing.

• Always disconnect power before changing signal and power

connections.

• Do not use this instrument on a work bench without its case for safety

reasons.

• Do not operate this instrument in flammable or explosive atmospheres.

• Do not expose this instrument to rain or moisture.

• Unit mounting should allow for adequate ventilation to ensure

instrument does not exceed operating temperature rating.

• Use electrical wires with adequate size to handle mechanical strain

and power requirements. Install without exposing bare wire outside the

connector to minimize electrical shock hazards.

EMC Considerations

• Whenever EMC is an issue, always use shielded cables.

• Never run signal and power wires in the same conduit.

• Use signal wire connections with twisted-pair cables.

• Install Ferrite Bead(s) on signal wires close to the instrument if EMC

problems persist.

Failure to follow all instructions and warnings may result in injury!

1.3 Before You Begin

Inspecting Your Shipment:

Remove the packing slip and verify that you have received everything

listed. Inspect the container and equipment for signs of damage as soon

as you receive the shipment. Note any evidence of rough handling in

transit. Immediately report any damage to the shipping agent. The carrier

will not honor damage claims unless all shipping material is saved for

inspection. After examining and removing the contents, save the packing

material and carton in the event reshipment is necessary.

Customer Service:

If you need assistance, please call the nearest Customer Service

Department, listed in this manual.

Manuals, Software:

The latest Operation and Communication Manual as well as free

configuration software are available at the website listed on the cover

page of this manual or on the CD-ROM enclosed with your

shipment.

For first-time users: Refer to the QuickStart Manual for basic operation

and set-up instructions.

The following steps in this manual for configuring your device are

explained by using the optional Remote Programmer Display (iDRP).

If you have the Serial Communications/Ethernet Option (-C24, -C4EI or

-EI) you can easily configure the controller on your computer or on-line.

To Reset the Meter:

When the monitor is in the "MENU" Mode, push c once to direct monitor

one step backward of the top menu item.

Push c twice to reset monitor, prior to resuming "Run" Mode except

after "Alarms", that will go to the "Run" Mode without resetting the

monitor.

PART 2

SETUP

Refer to the Quick Start Guide for assembly and disassembly

instructions.

2.1 Optional Remote Programmer Front Panel

Figure 2.1 Optional Remote Programmer Front Panel Display

Table 2.1 Front Panel Annunciators

1 Setpoint 1/ Alarm 1 indicator

2 Setpoint 2/ Alarm 2 indicator

°C °C unit indicator

°F °F unit indicator

Changes display to Configuration Mode and

advances through menu items*

Used in Program Mode and peak recall*

Used in Program Mode and valley recall*

Accesses submenus in Configuration Mode

and stores selected values*

* See Part 3 Operation: Configuration Mode

2.2 Front Panel Connections

The front panel connections are shown in Figures 2.2 and 2.3.

Figure 2.2 Input and Output Connections

Table 2.2 Connectors

POWER AC/DC Power Connector: All models

INPUT

Input Connector:

All models TC, PR (Process), RTD

OUTPUT 1 Based on one of the following models:

Relay SPDT

Solid State Relay

Pulse

OUTPUT 2 Based on one of the following models:

Relay SPDT

Solid State Relay

Pulse

OPTION

Based on one of the following models:

RS-232C or RS-485 programmable

Excitation

Output 1 and 2 are for -AL Limit Alarm Option only.

2.3 Electrical Installation

2.3.1 Power Connections

Caution: Do not connect power to your device until you have completed all

input and output connections. Failure to do so may result in injury!

Connect the main power connections as shown in the figure below.

Figure 2.3 Main Power Connections

Table 2.3 Power Connections

FUSE Connector For 115Vac For 230Vac DC

FUSE 1 Power * 100 mA(T) 100 mA(T) 100 mA(T)

FUSE 2 Power * N/A N/A 400 mA(T)

For the low voltage power option, in order to maintain the same degree of

protection as the standard high voltage input power units (90-240 Vac), always

use a Safety Agency Approved DC or AC source with the same Overvoltage

Category and pollution degree as the standard AC unit (90-240 Vac).

The Safety European Standard EN61010-1 for measurement, control,

and laboratory equipment requires that fuses must be specified based on

IEC127. This standard specifies for a Time-lag fuse, the letter code “T”.

The above recommended fuses are of the type IEC127-2-sheet III. Be

aware that there are significant differences between the requirements

listed in the UL 248-14/CSA 248.14 and the IEC 127 fuse standards. As a

result, no single fuse can carry all approval listings. A 1.0 Amp IEC fuse

is approximately equivalent to a 1.4 Amp UL/CSA fuse. It is advised to

consult the manufacturer’s data sheets for a cross-reference.

* See Specification Section

2.3.2 Thermocouple

The figure below shows the wiring hookup for any thermocouple type. For

example, for Type K hookup, connect the yellow wire to the "2" terminal and the

red wire to the "1(-)" terminal.

When configuring your monitor, select Thermocouple and Thermocouple

Type in the Input Type menu (see Part 3).

Figure 2.4 Thermocouple Wiring Hookup

If the input wires of the meter get disconnected or broken, it will display

+OPN “Input (+) Open” message. For safety purpose you may want to

set up your alarm to be triggered when input is open. See Alarm 1 and 2

chapters for details.

TYPE Input Connector Jacket (external insulation)

Terminal 1 (-) Terminal 2 (+) Extension Grade

J Red White dark-Brown Black

K Red Yellow dark-Brown Yellow

T Red Blue dark-Brown Blue

E Red Purple dark-Brown Purple

N Red Orange dark-Brown Brown

R Red Black - Green

S Red Black - Green

B Red Gray - Black

Table 2.4 TC Wire Color Chart

2.3.3 Two/Three/Four-Wire RTD

The figures below show the input connections and input connector jumpers

(shown in bold lines) required to hookup a 2-, 3- or 4-wire RTD.

Figure 2.5 a) RTD-1000 ohm and b) RTD-100 ohm Wiring Hookup

500 ohm Wiring Hookup

The two-wire connection is simplest method, but does not compensate for

lead-wire temperature change and often requires calibration to cancel lead-wire

resistance offset.

The three-wire connection works best with RTD leads closely equal in resistance.

The device measures the RTD, plus upper and lower lead drop voltage and the

subtracts twice the measured drop in the lower supply current lead producing

excellent lead-resistance cancellation for balanced measurements.

The four-wire RTD hookup is applicable to unbalanced lead resistance and

enables the device to measure and subtract the lead voltage, which produces the

best lead-resistance cancellation.

When configuring your monitor, select RTD type and RTD value in the Input

Type menu (see Part 3).

If the input wires of the meter get disconnected or broken, it will display

+OPN

“Input (+) Open” message except in case of 500/1000 Ω 2-wire

RTD. In this case the display shows

-OPN

“Input (-) Open” message. For

safety purpose you may want to set up your alarm to be triggered when

input is open. See Alarm 1 & 2 chapters for details.

2-WIRE

4-WIRE

3-WIRE

2-WIRE

4-WIRE

3-WIRE

2.3.4 Process Current

The figure below shows the wiring hookup for Process Current 0 – 20 mA.

Figure 2.6 Process Current Wiring Hookup

(Internal and External Excitation)

When configuring your instrument, select Process Type in the Input Type Menu

(see Part 3).

2.3.5 Process Voltage

The figure below shows the wiring hookup for Process Voltage 0 – 100 mV,

0 – 1 V, 0 – 10 V.

Figure 2.7 Process Voltage Wiring Hookup

(with Sensor Excitation and without Sensor Excitation)

RL - Voltage limited resistor, which allows to convert 24 Vdc internal excitation

voltage to the appropriate process input value. For instance: if the potentiometer

value is equal to 10 kΩ, the minimum RL is 14 kΩ for 10 V process input.

When configuring your instrument, select Process Type in the Input Type Menu

(see Part 3).

100 mV

Return

1 V or 10 V

100 mV

1 V or 10 V

Return

0-20 mA

Internal

Excitation

0-20 mA

External

Excitation

2.3.6 Wiring Outputs

This meter, if ordered with -AL, Limit Alarm Option, has two, factory installed,

outputs. The SPDT Mechanical Relay, SPST Solid State Relay and Pulse Output

Connection are shown below.

Figure 2.8

a) Mechnical Relay and SSR b) Pulse Output

Output Wiring Hookup Wiring Hookup

This device has snubber circuits designed to protect the contacts of the

mechanical relays when it switches to inductive loads (i.e. solenoids, relays).

These snubbers are internally connected between the Common (C) and

Normally Open (NO) relay contacts of Output 1 and Output 2.

If you have an inductive load connected between Common (C) and

Normally Closed (NC) contacts of the mechanical relays and you want to

protect them from the rush current during the switching period, you have

to connect an external snubber circuit between Common (C) and

Normally Closed (NC) contacts as indicated in the figure below.

Figure 2.9 Snubber Circuits Wiring Hookup

RC CIRCUIT

VARISTOR

275 V

OUTPUT 1 OUTPUT 2

100

1/4 W

0.033

SSR

RELAY

External

Load

External

Load

0.5 A (T)

3 A (T)

OUTPUT 1 OUTPUT 2

RETURN

PULSE

RETURN

PULSE

Figure 2.10 Typical Applications

TEMPERATURE

CONTROLLER

CONTROL

SIDE

dc INPUT

SSR

ac INPUT

SSR

ac INPUT

SSR

LOAD

SIDE

HEATER

Vac

dc CONTROLLED SSR USED WITH TEMPERATURE CONTROLLER WITH dc VOLTAGE SSR DRIVER OUTPUT

FAST BLOW

FUSE

0 or 5 Vdc,

TYPICALLY

TEMPERATURE

CONTROLLER

CONTROL

SIDE

LOAD

SIDE

HEATER

Vac

ac CONTROLLED SSR USED WITH TEMPERATURE CONTROLLER WITH MECHANICAL RELAY OUTPUT

FAST BLOW

FUSE

Vac

DRIVING

SSR

TEMPERATURE

CONTROLLER

CONTROL SIDE

LOAD

RESISTOR

LOAD

SIDE

HEATER

Vac

ac CONTROLLED SSR USED WITH TEMPERATURE CONTROLLER WITH TRIAC OUTPUT

FAST BLOW

FUSE

Vac

DRIVING

SSR

This device may have a programmable serial communication output.

The RS-232 and RS-485 Output Connections are shown below.

Figure 2.11 Serial Communication

a) RS-232 Output Wiring Hookup b) RS-485 Output Wiring Hookup

This device has built-in excitation. The connections are shown below.

Figure 2.12 Excitation Output

This device may have the Ethernet with embedded web server option.

The connections are shown below.

Figure 2.13 Embedded Ethernet

24 Vdc

RTN

-Tx / Rx

+Tx / Rx

PART 3

OPERATION: Configuration Mode

3.1 Introduction

The instrument has two different modes of operation. The first, Run Mode, is used to

display values for the Process Variable, and to display or clear Peak and Valley values.

The other mode, Menu Configuration Mode, is used to navigate through the menu

options and configure the unit. Part 3 of this manual will explain the Menu Configuration

Mode. For your instrument to operate properly, the user must first "program" or configure

the menu options.

Turning your Monitor On for the First Time

The device becomes active as soon as it is connected to a power source. It has no On or

Off switch. The device at first momentarily shows the software version number, followed

by reset

RST

, and then proceeds to the Run Mode.

For first-time users: Refer to the QuickStart Manual for basic operation and

set-up instructions.

The following steps in this manual for configuring your device are explained

by using the optional Remote Programmer Display (iDRP).

If you have the Serial Communications/Ethernet Option (-C24, -C4EI or -EI)

you can easily configure the controller on your computer or on-line.

Table 3.1 Button Function in Configuration Mode

• To enter the Menu, the user must first press

button.

• Use this button to advance/navigate to the next menu item. The user can navigate

through all the top level menus by pressing

• While a parameter is being modified, press

to escape without saving the

parameter.

• Press the up

button to scroll through “flashing” selections. When a numerical value is

displayed press this key to increase value of a parameter that is currently being modified.

• Holding the

button down for approximately 3 seconds will speed up the rate at

which the set point value increments.

• In the Run Mode press

causes the display to flash the PEAK value – press again

to return to the Run Mode.

• Press the down

button to go back to a previous Top Level Menu item.

• Press this button twice to reset the unit to the Run Mode.

• When a numerical value is flashing (except set point value) press

to scroll digits

from left to right allowing the user to select the desired digit to modify.

• When a setpoint value is displayed press

to decrease value of a setpoint that is

currently being modified. Holding the

button down for approximately 3 seconds will

speed up the rate at which the setpoint value is decremented.

• In the Run Mode press c causes the display to flash the VALLEY value – press

again to return to the Run Mode.

• Press the enter d button to access the submenus from a Top Level Menu item.

• Press d to store a submenu selection or after entering a value — the display will

flash a

STRD

message to confirm your selection.

• To reset flashing Peak or Valley press d.

•

In the Run Mode press d twice to enable Standby Mode with flashing

STBY

Reset: Except for Alarms, modifying any settings of the menu configuration will

reset the instrument prior to resuming Run Mode.

(MENU)

(UP)

(DOWN)

(ENTER)

3.2 Menu Configuration

Figure 3.1 Flow Chart for ID and Set Points Menu

3.2.1 ID Number Menu

SEE ID MENU SELECTION IN CONFIGURATION SECTION FOR

ENABLE/DISABLE OR CHANGE ID CODE.

If ID Code is Disabled or set as Default (0000) the menu will skip ID step

to Setpoint Menu.

If ID Code is set to Full Security Level and user attempts to enter the

Main Menu, they will be prompted for an ID Code.

If ID Code is set to Set Point/ID Security Level and user attempts to

enter the Configuration Menu, they will be prompted for an ID Code.

ENTERING YOUR NON-DEFAULT FULL SECURITY ID NUMBER.

Press a 1) Display shows

Press d 2) Display advances to

____

Press b & c 3) Press

to increase digit 0-9. Press

to activate next digit

(flashing). Continue to use

and c to enter your 4-digit ID

code.

Press d 4) If the correct ID code is entered, the menu will advance to the

Setpoint 1 Menu, otherwise an error message

ERRo

will be

displayed and the instrument will return to the Run Mode.

To change ID Code, see ID Menu in the Configuration section.

ENTERING YOUR NON-DEFAULT SET POINT/ID SECURITY ID NUMBER.

Press a 5) Display shows

SP1

Setpoint 1 Menu.

Press a 6) Display shows

SP2

Setpoint 2 Menu.

Press a 7) Display shows

ID Code Menu.

Press d 8) Display advances to

____

Press b & c 9) Use b and c to change your ID Code.

Press d 10) If correct ID Code is entered, the display will advance to the

INPT

Input Menu, otherwise the error message

ERRo

will be

displayed and the unit will return to the Run Mode.

To prevent unauthorized tampering with the setup parameters, the

instrument provides protection by requiring the user to enter the ID Code

before allowing access to subsequent menus. If the ID Code entered

does not match the ID Code stored, the unit responds with an error

message and access to subsequent menus will be denied.

Use numbers that are easy for you to remember. If the ID Code is

forgotten or lost, call customer service with your serial number to access

and reset the default to

0000

Page is loading ...

Omega iDR and iDR-AL Owner's manual

Brand: Omega

Model: iDR and iDR-AL

Category: Recording Equipment

Type: Owner's manual

Download PDF

report

Omega iDR and iDR-AL Owner's manual

Omega iDR and iDR-AL Owner's manual

Related papers

Other documents