Platinum Butlers Bell Kit Installation And Operation Instruction

Brand: Platinum

Model: Butlers Bell Kit

Type: Installation And Operation Instruction

The pulley system inside the house

Step 1:

By now the cord should be attached to the top of the black rod and have been passed

through the hole that was drilled in the wall for the cord. The inside wall plate (B) will hide

the hole for the cord on the inside of the house. Attach a pulley (1xA) using one of the

big srews (1xF). The screw should be at the back of the plate and the pulley on the front. The

cord comes through the silver hole then runs around the pulley. The inside wall plate (B)

can be positioned, so that when the cord comes through the wall it can go in all directions.

The other pulleys in the hardware pack allow you to manouvre the cord around the walls to

the Butlers Bell.

Warning: We advise that you use as little length of cord as possible, and as few pulleys

as possible. If a lot of cord is used the tension on the inner spring is lost in the cord.

Mounting the Butlers Bell

Step 2:

Place the wall mounted stem (I) up against the wall. Depending on if your cord is

coming from the left or the right of the butlers bell.

CORD COMING FROM THE LEFT:

The brass arm needs to be past vertical with the top pointing in a north easterly direction (fig.1).

This is done by making sure that the inner spring is pointng down, facing south west (fig.2).

When the cord is attached to the brass arm it will pullback the arm to a vertical position causing

tension on the inner spring.

CORD COMING FROM THE RIGHT:

The brass arm needs to be past vertical with the top pointing in a north westerly direction.

This is done by making sure that the inner spring is piontng down, facing south east (fig.3).

When the cord is attached to the brass arm it will pullback the arm to a vertical position causing

tension on the inner spring.

Fig.1

Fig.2

Fig.3

Brass arm

Step 3:

When you have found the right postion, you can begin to mark out the holes in order to secure

the wall mounted stem (I). Once the holes are marked and drilled with the appropriate 6mm drill bit, insert

3 wall plugs (3 x E) and then fix the wall mounted stem to the wall using 3 screws (3xH).

Step 4:

Once the wall mounted spindle (I) is in place, replace the inner spring in your chosen direction (ref step 2).

Step 4:

After the inner spring is fitted. take the bell (L) and place on the wall mounted spindle (I). Making sure

that when the brass arm is in its vertical position you can feel the tension on the inner spring

Step 5:

Screw the rosette (K) onto the wall mounted stem (I) so that the components stay in place.

Mounting the Butlers Bell (cont):

Step 6:

Now the butlers bell is mounted in position on the wall, the cord from the wall plate

pulley (B) needs to find its way to the bell. Sometimes this is very simple. For example,

If the inside wall plate (B) is at the right height for your butlers bell then the cord can

travel straight to the butlers bell. If the bell is below or above the wall plate then the angle

bracket has to be used. The wall plate sends the cord vertically up or down. The angle

bracket then sends the cord along the wall to the bell. (see below diagrams for alternative

mounting examples.

Step 7:

To attach the cord to the bell arm, pull the bell arm to the left (if your cord is coming

from the left) or to the right (if your cord is coming from the right), so that the cord can

be attached when the brass arm is vertical. Ensuring that the cord is taut, feed the cord

through the eyes at the top of the arm and tie a knot, so that the correct tension is

available for operation.

Customer support

A: C H Byron

Byron House

34, Sherwood Rd

Aston Fields

Bromsgrove

B60 3DR

T: 0845 2301231

E: [email protected]

W: www.chbyron.com

Step 8:

Congratulations, now sit back

and enjoy a cup of tea on us!

Instructions for

installing your new

Butlers Bell

Kit.

Introduction:

Thank you for choosing this traditional Byron bell. We at Byron hope that this product will give you a long lasting service.

If You need further assistance please call us. 0845 2301231

Contents list:

1 x Traditional Butlers Bell

1 x Butlers Bell Hardware Pack

Bell pull installation:

Step 1:

Screw A & B together

Parts:

Step 2:

Screw E onto the end of B.

Step 3: Slowly slide the rod through

D. The rod should go through the hole on the

plate first and then over the next support.

The bell pull:

A+B = Black iron rod

C = Top rod mounting

D = Bottom rod mounting

E = Handle

Step 4: Whilst the rod is placed

in D. Slide the rod on and through C. The rod

should pass through the hole first then the

spring. Place item G above the spring and

screw onto the top of the iron rod (A).

1st

2nd

1 x Black Bell Pull

1 x Black Pull Hardware Pack

YOU WILL NEED:

Flathead screwdriver

Electric drill

Appropriate 6mm drill bit

Appropriate 8mm drill bit

The hardware pack

F = Spring

G = Cord and

rod attachment

8 x black screws

(not shown)

8 x Wall plugs

(not shown)

Mounting your pull to the wall

Step 2

Once you have completed steps 1-4, the pull can be mounted to the wall.

Before securing the plates to the wall, locate the pull in a suitable position

so that when an 8mm hole is drilled to take the cord from the top of the ‘C’ plate, the

hole will be below the inside ceiling level in your hall, and away from any wall mounted

objects. Mark and drill the 8mm hole completely through your wall from the outside to the

inside. With the rod inserted (to ensure the plates are truly vertical) Mark and drill

the 4 screw holes on both ‘C’ and ‘D’ plates using the appropriate 6mm drill bit, taking care

to line up the previously drilled 8mm hole, with the hole at the top of the ‘C’ plate.

Remove the rod by unscrewing cap ‘G’ and secure the plates to the wall using the screws

and plugs provided.

Once the plates are fixed to the wall re-insert the black rod as in steps 3 & 4.

However before screwing on item ‘D’. Take the cord, tie a

knot in the one end. Then thread the cord

through item’G’ so that the knot is inside the barrell but

does not come through the hole. Then screw the the barrell back onto the rod,

thread the rest of the cord over the wheel and through the wall to the inside of

the house. This is best done using a straightened coathanger.

The Butlers Bell & Hardware Pack

G H

The hardware pack:

A- 3 x Pulley’s

B- 1 x Inside wall plate

C- 1 x Angle bracket

D- 1 x 9 metres of cord

E- 5 x Wall plugs

F- 2 x Large screws

G- 2 x Dowel screws

H- 5 x Brass screws

The Butlers bell:

I - 1 x Wall mounted stem

J - 1 x Inner spring

K - 1 x Rosette cap

L - 1 x Butlers bell

The hardware pack

The Butlers bell.

On opening the butlers bell kit (62500K), the Butlers bell will be assembled

together, as it should hang on the wall. Please keep the bell assembled in

order to continue.

Step 6

Platinum Butlers Bell Kit Installation And Operation Instruction