BNF UMX Pitts S-1S User manual

Brand: BNF

Model: UMX Pitts S-1S

Category: Remote controlled toys

Type: User manual

This manual is also suitable for

Instruction Manual

Bedienungsanleitung

Manuel d’utilisation

Manuale di Istruzioni

UMX

™

Pitts

S-1S

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the

product before operating. Failure to operate the product correctly can result in damage to the product,

personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires

some basic mechanical ability. Failure to operate this product in a safe and responsible manner could

result in injury or damage to the product or other property. This product is not intended for use by

children without direct adult supervision. Do not use with incompatible components or alter this product

in any way outside of the instructions provided by Horizon Hobby, Inc. This manual contains instructions

for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings

in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or

serious injury.

Safety Precautions and Warnings

• Always keep a safe distance in all directions

around your model to avoid collisions or injury.

This model is controlled by a radio signal subject

to interference from many sources outside your

control. Interference can cause momentary loss

of control.

• Always operate your model in open spaces away

from full-size vehicles, trafﬁ c and people.

• Always carefully follow the directions and

warnings for this and any optional support equip-

ment (chargers, rechargeable battery packs, etc.).

• Always keep all chemicals, small parts and

anything electrical out of the reach of children.

• Always avoid water exposure to all equipment

not speciﬁ cally designed and protected for this

purpose. Moisture causes damage to electronics.

• Never place any portion of the model in your

mouth as it could cause serious injury or

even death.

• Never operate your model with low transmitter

batteries.

• Always keep aircraft in sight and under control.

• Always use fully charged batteries.

• Always keep the transmitter powered on while

aircraft is powered.

• Always remove batteries before disassembly.

• Always keep moving parts clean.

• Always keep parts dry.

• Always let parts cool after use before touching.

• Always remove batteries after use.

• Always ensure failsafe is properly set

before ﬂ ying.

• Never operate aircraft with damaged wiring.

• Never touch moving parts.

Age Recommendation: Not for children under 14 years. This is not a toy.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion

of Horizon Hobby, Inc. For up-to-date product literature, visit www.horizonhobby.com and click on the

support tab for this product.

Meaning of Special Language:

The following terms are used throughout the product literature to indicate various levels of potential

harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage

AND little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property

damage AND a possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage,

collateral damage, and serious injury OR create a high probability of superﬁ cial injury.

hank you for purchasing the E-ﬂ ite

UMX

™

Pitts

S-1S ultra micro airplane. Despite its size, this model

has been engineered to deliver a potent scale model that handles great. Molded lightweight foam

construction makes it possible for the high-output brushless power system installed to provide quick

acceleration and strong vertical climbs. Four performance linear long-throw servos provide precision

control. But what truly makes this go-anywhere biplane special is the remarkable AS3X

system that’s been

specially tuned to give you the feeling of ﬂ ying a much larger model. AS3X stability works especially hard so

even when wind conditions are moderate, you experience the kind of smooth ﬂ ight that makes you want to

ﬂ y more often.

A thorough read of this manual will help assure that you’re well equipped to successfully enjoy all the

beneﬁ ts this outstanding ultra micro model has to offer.

To register your product online, go to www.e-ﬂ iterc.com

Installed

Motor: 180BL 3000Kv Brushless

Outrunner (EFLUM180BLB)

Receiver : Spektrum

™

6-Ch AS3X

Receiver with BL ESC (SPMAS6410NBL)

(4) 2.3-Gram Performance Linear Long

Throw Servo (SPMSA2030L)

Needed to Complete

Recommended Battery: 200mAh 2S

7.4V 25C Li-Po, 26AWG (EFLB2002S25)

Recommended Battery Charger:

Celectra

™

2S 7.4V DC Li-Po Charger

(EFLUC1007)

Recommended Transmitter:

Spektrum

™

DSM2

/DSMX

full range

with dual-rates (DX4e and up)

15.5 in (393mm)

17.1 in (434mm)

3.2 oz

(90 g)

Preﬂ ight Checklist ..................................................4

AS3X Stabilization Delivers Breakthrough

Performance ..........................................................4

Low Voltage Cutoff (LVC) ........................................4

Transmitter and Receiver Binding ...........................5

ESC/Receiver Arming, Battery Installation

and Center of Gravity .............................................6

Control Direction Test .............................................7

Control Centering ..................................................7

Control Horn Settings .............................................7

Dual Rates .............................................................7

Flying Tips and Repairs ..........................................8

Post Flight Checklist ..............................................8

Power Components Service ...................................9

Troubleshooting Guide .........................................10

Troubleshooting Guide (Continued) .......................11

Limited Warranty .................................................11

Warranty and Service Information ........................13

Compliance Information for the European Union ...13

Replacement Parts ...............................................50

Optional Parts and Accessories ............................51

Table of Contents

Speciﬁ cations



1. Charge ﬂ ight battery.

2. Install ﬂ ight battery in aircraft (once it

has been fully charged).

3. Bind aircraft to transmitter.

4. Make sure linkages move freely.

5. Perform Control Direction Test with

transmitter.



6. Set dual rates and expos.

7. Adjust center of gravity.

8. Perform a radio system Range Check.

9. Find a safe and open area.

10. Plan ﬂ ight for ﬂ ying ﬁ eld conditions.

Horizon Hobby has always made RC sport, scale

and unique aircraft with the kind of performance

experts appreciate. Now the exclusive Artificial

Stability – 3 aXis (AS3X) system helps take

performance expectations in ultra micro aircraft a

quantum leap higher.

Based on the successful use of MEMS sensor

technology within the AS3X Stabilization System

essential to Blade

ultra micro flybarless

helicopters, the specifically tuned AS3X System

for airplanes helps invisibly correct for turbulence,

torque and tip stalls when encountered.

Furthermore, the outstanding control agility delivers

an ultra smooth, locked-in feel that obeys your

every command with performance that’s natural

feeling. It’s so gratifying, in fact, that it’s as though

you’re the RC pilot of an expertly tuned, giant-scale

model.

AS3X will change the way you’ll want to fly now and

in the future. To see what we mean, go to

www.E-fliteRC.com/AS3X.

Preﬂ ight Checklist

AS3X Stabilization Delivers Breakthrough Performance

When a Li-Po battery is discharged below 3V per

cell, it will not hold a charge. The aircraft’s ESC

protects the ﬂ ight battery from over-discharge

using Low Voltage Cutoff (LVC). Once the battery

discharges to 3V per cell, the LVC will reduce the

power to the motor in order to leave adequate

power to the receiver and servos to land the

airplane.

When the motor power decreases, land the aircraft

immediately and replace or recharge the ﬂ ight

battery.

Always disconnect and remove the Li-Po battery

from the aircraft after each ﬂ ight. Charge your Li-Po

battery to about half capacity before storage. Make

sure the battery charge does not fall below 3V per

cell. Failure to unplug a connected battery will result

in trickle discharge.

For your ﬁ rst ﬂ ights, set your transmitter timer or a

stopwatch to 5 minutes. Adjust your timer for longer

or shorter ﬂ ights once you have ﬂ own the model.

NOTICE: Repeated ﬂ ying to LVC will damage the

battery.

Low Voltage Cutoff (LVC)

Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identiﬁ er)

code of a single speciﬁ c transmitter. You need to ‘bind’ your chosen Spektrum

™

DSM2/DSMX technology

equipped aircraft transmitter to the receiver for proper operation.

Any full range Spektrum DSM2/DSMX transmitter can bind to the DSM2/DSMX receiver. Please visit www.

bindnﬂ y.com for a complete list of compatible transmitters.

Transmitter and Receiver Binding



Binding Procedure

CAUTION: When using a Futaba transmitter with a Spektrum DSM

module, you must reverse the

throttle channel and rebind. Refer to your Spektrum module manual for binding and failsafe instructions.

Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.

1. Refer to your transmitter’s unique instructions for binding to a receiver (location of transmitter’s

Bind control).

2. Make sure the ﬂ ight battery is disconnected from the aircraft.

3. Power off your transmitter.

4. Connect the ﬂ ight battery in the aircraft. The receiver LED will begin to ﬂ ash rapidly (typically after

5 seconds).

5. Make sure the transmitter controls are neutral and the throttle and throttle trim are in low position.

6. Put your transmitter into bind mode. Refer to your transmitter’s manual for binding button or

switch instructions.

7. After 5 to 10 seconds, the receiver status LED will turn solid, indicating that the receiver is bound

to the transmitter. If the LED does not turn solid, refer to the Troubleshooting Guide at the back of

the manual.

1-2-3-4-5 Sec.

ESC/Receiver Arming, Battery Installation and Center of Gravity

CAUTION: Always keep hands away from the

propeller. When armed, the motor will turn the

propeller in response to any throttle movement.

Arming the ESC/receiver also occurs after binding

as previously described, but subsequent connection

of a ﬂ ight battery requires the following steps.

AS3X

The AS3X

system will not activate until the

throttle stick or trim is increased for the first

time. Once active, the control surfaces may

move rapidly and noisily on the aircraft.

This is normal. AS3X technology will remain

active until the battery is disconnected.

1. Remove the battery hatch from the fuselage.

2. Attach the battery to the hook and loop strip so

the battery is against the motor mount.

Center of Gravity (CG)

At the wing root, measure the CG location 32.5mm

back from the forward-most leading edge of the

top wing.

3. Lower the throttle and throttle trim to the

lowest settings on your transmitter. Power

on your transmitter, then wait 5 seconds.

4. Connect the battery to the ESC, noting proper

polarity. Keep the plane immobile and away

from wind for 5 seconds to allow the AS3X

system to initialize. A series of tones and

a continuous LED indicates a successful

connection.

CAUTION: Always disconnect the Li-Po

battery from the ESC when not ﬂ ying to eliminate

power supplied to the motor. The ESC does not have

an arming switch and will respond to any

transmitter input when a signal is present.

CAUTION: Always disconnect the Li-Po

battery from the ESC when not ﬂ ying to avoid

over-discharging the battery. Batteries discharged

to a voltage lower than the lowest approved voltage

may become damaged, resulting in loss of

performance and potential ﬁ re when batteries

are charged.

32.5mm

Before the ﬁ rst ﬂ ights, or in the event of an

accident, make sure the ﬂ ight control surfaces

are centered. Adjust the linkages mechanically if

the control surfaces are not centered. Use of the

transmitter sub-trims may not correctly center the

aircraft control surfaces due to the mechanical

limits of linear servos.

1. Make sure the control surfaces are neutral

when the transmitter controls and trims are

centered. The transmitter sub-trim must

always be set to zero.

2. When needed, use a pair of pliers to carefully

bend the metal linkage (see illustration).

3. Make the U-shape narrower to make the

connector shorter. Make the U-shape wider

to make the linkage longer.

Centering Controls After First Flights

For best performance with AS3X, it is important

that excessive trim is not used. If the aircraft re-

quires excessive transmitter trim (4 or more clicks

of trim per channel), return the transmitter trim

to zero and adjust the linkages mechanically so

that the control surfaces are in the ﬂ ight trimmed

position.

Control Centering

Control Horn Settings

The table to the right shows the factory settings for

the control horns. Fly the aircraft at factory settings

before making changes.

After ﬂ ying, you may choose to adjust the linkage

positions for the desired control response.

CAUTION: When these are incorrectly

connected for the pilot’s skill level, unexpected

aircraft response to controls can result. This can

cause damage to the aircraft and personal injury.

Aileron Elevator Rudder

Dual Rates

To obtain the best ﬂ ight performance, we

recommend using a DSM2/DSMX radio capable

of adjustable Dual Rates. The suggested settings

shown here are the recommended starting settings.

Adjust according to the individual preferences after

the initial ﬂ ight.

NOTICE: Do not set your transmitter travel adjust

over 100%. If the TRAVEL ADJUST is set over

100%, it will not result in more control movement, it

will overdrive the servo and cause damage.

It is normal for linear servos to make signiﬁ cant

noise. The noise is not an indication of a faulty

servo.

Tip: For the ﬁ rst ﬂ ight, ﬂ y the model in low rate.

Dual Rate

High Low

Aileron 100% 70%

Elevator 100% 70%

Rudder 100% 70%

Control Direction Test

You should bind your aircraft and transmitter before

doing these tests. Move the controls on the trans-

mitter to make sure the aircraft control surfaces

move correctly and in the proper direction.

Make sure the tail linkages move freely and that

paint or decals are not adhered to them.

Post Flight Checklist



1. Disconnect the ﬂ ight battery from the ESC

(Required for safety and battery life).

2. Power OFF the transmitter.

3. Remove the ﬂ ight battery from the

aircraft.

4. Recharge the ﬂ ight battery.



5. Store the ﬂ ight battery apart from the

aircraft and monitor the battery charge.

6. Make note of the ﬂ ight conditions and

ﬂ ight plan results, planning for future

ﬂ ights.

We recommend ﬂ ying your aircraft outside in calm

conditions. Always avoid ﬂ ying near houses, trees,

wires and buildings. You should also be careful to

avoid ﬂ ying in areas where there are many people,

such as busy parks, schoolyards or soccer ﬁ elds.

Consult local laws and ordinances before choosing

a location to ﬂ y your aircraft.

Takeoff

Place the aircraft in position for takeoff (facing into

the wind if ﬂ ying outdoors). Set dual rates to low

position and gradually increase the throttle to ¾ to

full and steer with the rudder. Pull back gently on

the elevator and climb to check trim. Once the trim

is adjusted, begin exploring the ﬂ ight envelope of

the aircraft.

Landing

Land into the wind. This is very important for this

model. Fly the aircraft to approximately 6 inches

(15cm) or less above the runway, using a small

amount of throttle for the entire descent. Keep the

throttle on until the aircraft is ready to ﬂ are. During

ﬂ are, keep the wings level and the airplane pointed

into the wind. Gently lower the throttle while pulling

back on the elevator to bring the aircraft down on

all three wheels.

Failure to lower the throttle stick

and trim to the lowest possible

positions during a crash could

result in damage to the ESC in

the receiver unit, which may

require replacement.

This aircraft is equipped with

Over Current Protection (OCP).

This feature protects the ESC

from overheating. OCP stops the

motor when the transmitter throttle is set too high

and the propeller cannot turn. The OCP will only

activate when the throttle stick is positioned just

above 1/2 throttle. After the ESC stops the motor,

fully lower the throttle to re-arm the ESC.

NOTICE: Crash damage is not covered under the

warranty.

Repairs

Repair the aircraft using foam-compatible CA

(cyanoacrylate adhesive) or clear tape. Only use

foam-compatible CA, as other types of glue can

damage the foam. When parts are not repairable,

see the Replacement Parts List for ordering by

item number.

For a listing of all replacement and optional parts,

refer to the list at the end of this manual.

NOTICE: Use of foam-compatible CA accelerant on

your aircraft can damage paint. DO NOT handle the

aircraft until the accelerant fully dries.

NOTICE: When you are ﬁ nished ﬂ ying, never leave

the aircraft in direct sunlight or in a hot, enclosed

area such as a car. Doing so can damage the foam.

Flying Tips and Repairs

Always

decrease throttle at

propeller strike.

CAUTION

Power Components Service

Disassembly

CAUTION: DO NOT handle the propeller

while the ﬂ ight battery is connected to the ESC.

Personal injury could result.

Propeller

1. Remove the spinner (A) from the propeller.

Since the propeller and spinner are glued

together, glue residue will need to be cleaned

from the spinner or propeller when these parts are

used again.

2. Carefully remove the screw (B) and propeller

Motor

1. Remove the battery hatch by gripping the front

of the hatch, then pulling it up and away from

the fuselage.

2. Disconnect the motor wire connector from

the ESC/receiver connector.

3. Remove the screw (D) and motor (E) from the

motor mount.

4. Remove 3 screws (F) and the prop adapter (G)

from the motor. The motor magnet may attract

screws to the motor.

Assembly

Assemble in reverse order.

• Connect the motor wire connector to the ESC/

receiver.

• The propeller size numbers (5.75x2.25) must

face out from the motor for correct propeller

operation.

• Ensure the propeller adapter and motor mount

are fully connected to the motor.

AS3X

Problem Possible Cause Solution

Control surfaces not at

neutral position when

transmitter controls are

at neutral

Control surfaces may not have been

mechanically centered from factory

Center control surfaces mechanically by

adjusting the U-bends on control linkages

Aircraft was moved after the ﬂ ight battery

was connected and before sensors

initialized

Disconnect and reconnect the ﬂ ight battery

while keeping the aircraft still for 5 seconds

Model ﬂ ies inconsis-

tently from ﬂ ight to

ﬂ ight

Aircraft was not kept immobile for 5

seconds after battery was plugged in

Keep the aircraft immobile for 5 seconds after

plugging in the battery

Trims are moved too far from neutral

position

Neutralize trims and mechanically adjust

linkages to center control surfaces

Controls oscillate in

ﬂ ight, (model rapidly

jumps or moves)

Propeller is unbalanced, causing excessive

vibration

Remove propeller and rebalance or replace it

if damaged

Prop screw is too loose, causing vibration Tighten the prop screw

Problem Possible Cause Solution

Aircraft will not respond

to throttle but responds

to other controls

Throttle stick and/or throttle trim too high Reset controls with throttle stick and throttle

trim at lowest setting

Throttle channel is reversed Reverse throttle channel on transmitter

Motor disconnected from receiver Open fuselage and make sure motor is

connected to the receiver

Extra propeller noise or

extra vibration

Damaged propeller, spinner or motor Replace damaged parts

Prop screw is too loose Tighten the prop screw

Prop is out of balance Remove and balance propeller, or replace

with a balanced propeller

Reduced ﬂ ight time or

aircraft underpowered

Flight battery charge is low Completely recharge ﬂ ight battery

Propeller installed backwards Install propeller with numbers facing forward

Flight battery damaged Replace ﬂ ight battery and follow ﬂ ight battery

instructions

Flight conditions may be too cold Make sure battery is warm before use

Battery capacity too low for ﬂ ight conditions Replace battery or use a larger capacity

battery

LED on receiver ﬂ ashes

and aircraft will not bind

to transmitter (during

binding)

Transmitter too near aircraft during binding

process

Power off transmitter, move transmitter a

larger distance from aircraft, disconnect and

reconnect ﬂ ight battery to aircraft and follow

binding instructions

Bind switch or button not held long enough

during bind process

Power off transmitter and repeat bind pro-

cess. Hold transmitter bind button or switch

until receiver is bound

Aircraft or transmitter is too close to large

metal object, wireless source or another

transmitter

Move aircraft and transmitter to another

location and attempt binding again

Troubleshooting Guide

Problem Possible Cause Solution

LED on receiver ﬂ ashes

rapidly and aircraft will

not respond to transmit-

ter (after binding)

Less than a 5-second wait between ﬁ rst

powering on transmitter and connecting

ﬂ ight battery to aircraft

Leaving transmitter on, disconnect and

reconnect ﬂ ight battery to aircraft

Aircraft bound to different model memory

(ModelMatch

™

radios only)

Select correct model memory on transmitter

and disconnect and reconnect ﬂ ight battery

to aircraft

Flight battery/transmitter battery charge is

too low

Replace/recharge batteries

Transmitter may have been bound to a

different model (or with a different DSM

Protocol)

Select the right transmitter or bind to the

new one

Aircraft or transmitter is too close to large

metal object, wireless source or another

transmitter

Move aircraft and transmitter to another

location and attempt linking again

Control surface does

not move

Control surface, control horn, linkage or

servo damage

Replace or repair damaged parts and adjust

controls

Wire damaged or connections loose Do a check of wires and connections, con-

nect or replace as needed

Flight battery charge is low Fully recharge ﬂ ight battery

Control linkage does not move freely Make sure control linkage moves freely

Controls reversed Transmitter settings reversed Adjust controls on transmitter appropriately

Motor loses power Damage to motor or power components Do a check of motor and power components

for damage (replace as needed)

Motor power quickly

decreases and in-

creases then motor

loses power

Battery power is down to the point of

receiver/ESC Low Voltage Cutoff (LVC)

Recharge ﬂ ight battery or replace battery that

is no longer performing

Motor/ESC is not armed

after landing

Over Current Protection (OCP) stops the

motor when the transmitter throttle is set

high and the propeller cannot turn

Fully lower throttle and throttle trim to

arm ESC

Servo locks or freezes

at full travel

Travel adjust value is set above 100%,

overdriving the servo

Set Travel adjust to 100% or less and/or set

sub-trims to Zero and adjust linkages

mechanically

Troubleshooting Guide (Continued)

What this Warranty Covers

Horizon Hobby, Inc. (“Horizon”) warrants to the original

purchaser that the product purchased (the “Product”) will

be free from defects in materials and workmanship at the

date of purchase.

What is Not Covered

This warranty is not transferable and does not cover

(i) cosmetic damage, (ii) damage due to acts of God,

accident, misuse, abuse, negligence, commercial

use, or due to improper use, installation, operation or

maintenance, (iii) modiﬁ cation of or to any part of the

Product, (iv) attempted service by anyone other than

a Horizon Hobby authorized service center, (v) Product

not purchased from an authorized Horizon dealer, or

(vi) Product not compliant with applicable technical

regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON

MAKES NO OTHER WARRANTY OR REPRESENTATION, AND

HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,

INCLUDING, WITHOUT LIMITATION, THE IMPLIED

WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. THE

PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE

DETERMINED THAT THE PRODUCT WILL SUITABLY MEET

THE REQUIREMENTS OF THE PURCHASER’S INTENDED

USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and

exclusive remedy shall be that Horizon will, at its option,

either (i) service, or (ii) replace, any Product determined

by Horizon to be defective. Horizon reserves the right to

inspect any and all Product(s) involved in a warranty claim.

Service or replacement decisions are at the sole discretion

Limited Warranty

of Horizon. Proof of purchase is required for all warranty

claims. SERVICE OR REPLACEMENT AS PROVIDED

UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND

EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF

PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY

WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED

IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT

LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF

HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. Further, in no event shall the liability

of Horizon exceed the individual price of the Product on

which liability is asserted. As Horizon has no control over

use, setup, ﬁ nal assembly, modiﬁ cation or misuse, no

liability shall be assumed nor accepted for any resulting

damage or injury. By the act of use, setup or assembly, the

user accepts all resulting liability. If you as the purchaser

or user are not prepared to accept the liability associated

with the use of the Product, purchaser is advised to return

the Product immediately in new and unused condition to

the place of purchase.

Law

These terms are governed by Illinois law (without regard to

conﬂ ict of law principals). This warranty gives you speciﬁ c

legal rights, and you may also have other rights which vary

from state to state. Horizon reserves the right to change

or modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot

provide warranty support or service. Once assembly, setup

or use of the Product has been started, you must contact

your local distributor or Horizon directly. This will enable

Horizon to better answer your questions and service

you in the event that you may need any assistance. For

questions or assistance, please visit our website at www.

horizonhobby.com, submit a Product Support Inquiry,

or call the toll free telephone number referenced in the

Warranty and Service Contact Information section to speak

with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is

compliant in the country you live and use the Product in,

please use the Horizon Online Service Request submission

process found on our website or call Horizon to obtain a

Return Merchandise Authorization (RMA) number. Pack

the Product securely using a shipping carton. Please

note that original boxes may be included, but are not

designed to withstand the rigors of shipping without

additional protection. Ship via a carrier that provides

tracking and insurance for lost or damaged parcels, as

Horizon is not responsible for merchandise until it arrives

and is accepted at our facility. An Online Service Request

is available at http://www.horizonhobby.com/content/_

service-center_render-service-center. If you do not have

internet access, please contact Horizon Product Support

to obtain a RMA number along with instructions for

submitting your product for service. When calling Horizon,

you will be asked to provide your complete name, street

address, email address and phone number where you can

be reached during business hours. When sending product

into Horizon, please include your RMA number, a list of

the included items, and a brief summary of the problem.

A copy of your original sales receipt must be included

for warranty consideration. Be sure your name, address,

and RMA number are clearly written on the outside of the

shipping carton.

NOTICE: Do not ship LiPo batteries to Horizon. If you

have any issue with a LiPo battery, please contact the

appropriate Horizon Product Support ofﬁ ce.

Warranty Requirements

For Warranty consideration, you must include your

original sales receipt verifying the proof-of-purchase

date. Provided warranty conditions have been met,

your Product will be serviced or replaced free of charge.

Service or replacement decisions are at the sole discretion

of Horizon.

Non-Warranty Service

Should your service not be covered by warranty,

service will be completed and payment will be

required without notiﬁ cation or estimate of the

expense unless the expense exceeds 50% of the retail

purchase cost. By submitting the item for service you are

agreeing to payment of the service without notiﬁ cation.

Service estimates are available upon request. You must

include this request with your item submitted for service.

Non-warranty service estimates will be billed a minimum

of ½ hour of labor. In addition you will be billed for return

freight. Horizon accepts money orders and cashier’s

checks, as well as Visa, MasterCard, American Express,

and Discover cards. By submitting any item to Horizon

for service, you are agreeing to Horizon’s Terms and

Conditions found on our website http://www.horizonhobby.

com/content/_service-center_render-service-center.

ATTENTION: Horizon service is limited to Product

compliant in the country of use and ownership.

If received, a non-compliant Product will not be

serviced. Further, the sender will be responsible for

arranging return shipment of the un-serviced Product,

through a carrier of the sender’s choice and at the

sender’s expense. Horizon will hold non-compliant

Product for a period of 60 days from notiﬁ cation, after

which it will be discarded.

Declaration of Conformity

Compliance Information for the European Union

(in accordance with ISO/IEC 17050-1)

No. HH2014021501

Product(s): EFL UMX S-1S Pitts BNF

Item Number(s): EFLU5250

Equipment class: 1

The object of declaration described above is in conformity with the requirements of the speciﬁ cations listed

below, following the provisions of the European R&TTE Directive 1999/5/EC and EMC Directive 2004/108/EC

and LVD Directive 2006/95/EC:

EN 301 489-1 V1.9.2: 2012

EN301 489-17 V2.1.1: 2009

EN60950-1:2006+A11:2009+A1:2010+A12: 2011

EN55022:2010 + AC:2011

EN55024:2010

Signed for and on behalf of:

Horizon Hobby, Inc.

Champaign, IL USA

Feb 15, 2014

Robert Peak

Chief Financial Ofﬁ cer

Horizon Hobby, Inc.

Warranty and Service Information

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed of with other waste. Instead, it is the user’s responsibility

to dispose of their waste equipment by handing it over to a designated collections point for the

recycling of waste electrical and electronic equipment. The separate collection and recycling

of your waste equipment at the time of disposal will help to conserve natural resources and

ensure that it is recycled in a manner that protects human health and the environment. For more

information about where you can drop off your waste equipment for recycling, please contact your local city

ofﬁ ce, your household waste disposal service or where you purchased the product.

Country of Purchase Horizon Hobby Phone Number/Email Address Address

United States of

America

Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.

com/RequestForm/

4105 Fieldstone Rd

Champaign, Illinois, 61822 USA

Horizon Product Support

(Product Technical Assistance)

www.quickbase.com/db/

bghj7ey8c?a=GenNewRecord

888-959-2305

Sales

sales@horizonhobby.com

888-959-2305

United Kingdom

Service/Parts/Sales:

Horizon Hobby Limited

sales@horizonhobby.co.uk Units 1–4 , Ployters Rd,

Staple Tye Harlow, Essex,

CM18 7NS, United Kingdom

+44 (0) 1279 641 097

Germany

Horizon Technischer Service service@horizonhobby.de

Christian-Junge-Straße 1

25337 Elmshorn, Germany

Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100

France

Service/Parts/Sales:

Horizon Hobby SAS

infofrance@horizonhobby.com

11 Rue Georges Charpak

77127 Lieusaint, France

+33 (0) 1 60 18 34 90

China

Service/Parts/Sales:

Horizon Hobby – China

info@horizonhobby.com.cn Room 506,

No. 97 Changshou Rd.

Shanghai, China 200060

+86 (021) 5180 9868

Replacement Parts – Ersatzteile –

– Pièces de rechange – Pezzi di ricambio –

Part # • Nummer

Numéro • Codice

Description Beschreibung Description Descrizione

EFLU5265

Decal Set: UMX Pitts

S-1S

Dekorbogen: UMX

Pitts S-1S

Set de décoration:

UMX Pitts S-1S

Set adesivi: UMX Pitts

S-1S

EFLU5251

Spinner Set (3):

UMX Pitts S-1S

E-ﬂ ite UMX Pitts

S-1S: Spinner Set

Cônes (3) : UMX Pitts

S-1S

Set ogiva (3): UMX

Pitts S-1S

EFLU5255

Landing Gear Set w/

Wheel Pants: UMX

Pitts S-1S

E-ﬂ ite UMX Pitts

S-1S: Fahrwerk m.

Radschuhe

Train d’atterrissage

avec carénages de

roues : UMX Pitts

S-1S

Set carrello con

carenature ruote: UMX

Pitts S-1S

EFLU5261

Interplane Strut Set:

UMX Pitts S-1S

E-ﬂ ite UMX

Pitts S-1S:

Tragﬂ ächenstreben

Set de haubans : UMX

Pitts S-1S

Set montanti alari:

UMX Pitts S-1S

EFLU5259

Wing Set: E-ﬂ ite

UMX Pitts S-1S

E-ﬂ ite UMX Pitts

S-1S: Tragﬂ ächen

UMX UMX Pitts S-1S

-Aile

Ala: UMX Pitts S-1S

EFLU5260

Tail Set w/

Accessories: UMX

Pitts S-1S

E-ﬂ ite UMX Pitts

S-1S: Leitwerk Set

mit Zubehör

UMX Pitts S-1S -Set

d’empennage

Set coda c/Acc: UMX

Pitts S-1S

FLU5262

Battery Hatch: UMX

Pitts S-1S

E-ﬂ ite UMX Pitts

S-1S: Akkuklappe

Trappe à batterie :

UMX Pitts S-1S

Portello batteria: UMX

Pitts S-1S

EFLU5246

Pushrod/Wing Brace

Set: UMX Pitts S-1S

E-ﬂ ite UMX Pitts

S-1S: Gestänge /

Tragﬂ ächenhalter

Set de tringleries :

UMX Pitts S-1S

Set aste/ﬁ ssaggi ala:

UMX Pitts S-1S

EFLU5030

Motor Mount: UMX

Yak 54 180

E-ﬂ ite UMX Yak 54

180: Motorhalter

UMX Yak 54 180 -

Support moteur

Supporto motore: UMX

Yak 54 180

EFLU5258

Fuselage w/Cabane

and Hatch: UMX

Pitts S-1S

E-ﬂ ite UMX Pitts

S-1S: Rumpf m.

Haube

Fuselage avec cabane

et trappe : UMX Pitts

S-1S

Fusoliera con cabana

e portello: UMX Pitts

S-1S

EFLU5270

Ultra Micro 1/14th

Scale Aerobatic Pilot

Ultra Micro 1/14th

Scale Aerobatik Pilot

Pilote de voltige pour

Ultra Micro 1/14

Ultra Micro Pilota

Acrobatico in scala

1/14

EFLUP575225

5.75x2.25 Electric

Propeller: UMX

Yak 54

5.75x2.25: UMX

Yak 54

5.75x2.25 Hélice élec-

trique: UMX Yak 54

Elica 5.75x2.25: UMX

Yak 54

EFLU4067

Prop Adapter: UMX

Beast

Eﬂ ite Propeller Adap-

ter: UMX Beast

Adaptateur d’hélice:

UMX Beast

Adattatore elica: UMX

Beast

EFLUM180BLB

180 Brushless

Outrunner Motor

3000Kv

BL180 Brushless

Außenläufer Motor

3000 kv

Moteur brushless à

cage tournante 180

3000kv

180 Motore brushless

cassa rotante 3000KV

SPMAS6410NBL

Spektrum 6 Ch

AS3X Receiver w/

BL ESC

Spektrum 6 Kanal

AS3X Empfänger m.

BL Regler

Module Spektrum 6

voies Rx/ESC/AS3X

Ricevitore Spektrum 6

CH AS3X con ESC BL

SPMSA2030L

2.3-Gram

Performance Linear

Long Throw Servo

2,3 Gramm

Hochleistungs -

Linear Servo mit

langem Ruderweg

Servo 2.3g linéaire

longue course

performant

Ottimo servo lineare

a corsa lunga da 2,3

Grammi

SPM6836

Replacement Servo

Mechanics: 2.3-

Gram 2030L

Ersatzservom-

echanik 2,3 Gramm

2030L

Pièces de rechange

mécaniques servo:

2,3g 2030 L

Componenti meccanici

di ricambio del servo:

2030L da 2,3 grammi

– Optional Parts and Accessories –

– Optionale Bauteile und Zubehörteile –

– Pièces optionnelles et accessoires –

– Pezzi opzionali e accessori –

Part # • Nummer

Numéro • Codice

Description Beschreibung Description Descrizione

PKZ1039

Hook and Loop Set

(5): Ultra Micros

Parkzone: Klettband

Set Ultra Micros

Ultras Micros - Bande

auto-agrippante (5)

Set fascette a strappo

(5): Ultra Micro

EEFLB2002S25

2S 7.4V 200mAh 25C

Li-Po Battery

2S 7.4V 200mAh 25C

Li-Po Akku

Batterie Li-Po 7.4V

2S 25C 200mA

2S 7.4V 200mAh 25C

Li-Po Batteria

EEFLB2002S30

2S 7.4V 200mAh 30C

Li-Po Battery

2S 7.4V 200mAh 30C

Li-Po Akku

Batterie Li-Po 7.4V

2S 30C 200mA

2S 7.4V 200mAh 30C

Li-Po Batteria

EEFLB1502S45

2S 7.4V 150mAh 45C

Li-Po Battery

2S 7.4V 150mAh 45C

Li-Po Akku

Batterie Li-Po 7.4V

2S 45C 150mA

2S 7.4V 150mAh 45C

Li-Po Batteria

EFLUC1007

Celectra 2S 7.4V

DC Li-Po Charger

Celectra 2S 7.4V DC

Li-Po Ladegerät

Celectra Chargeur

Li-Po 7.4V 2S

Celectra 2S 7.4V DC

Li-Po Caricabatterie

EFLUC1008

DC Power Cord: UMX

Beast

DC Ladekabel UMX

Beast

Alimentation DC DC Cavo alimenta-

zione: UMX Beast

EFLA700UM

Charger Plug Adapter:

EFL

Ladekabel Adapter

EFL

Prise d’adaptation

chargeur: EFL

Adattatore connettore

caricabatterie: EFL

EFLA7001UM

Charger Plug Adapter:

Thunder Power

Ladekabel Adapter

Thunder Power

Prise d’adaptation

chargeur: Thunder

Power

Adattatore connettore

caricabatterie:

Thunder Power

EFLU4068

Harness Adapter: UMX

Beast

E-ﬂ ite UMX Beast

Y-Kabel

Adaptateur de

câblage: UMX Beast

Adattatore collegam-

enti: UMX Beast

EFLC4000/UK/

AU/EU

AC to 12V DC,1.5 Amp

Power Supply (Based

upon your sales

Region)

Netzteil 12V 1,5 A

(Basierend nach

Vertriebsregion)

Alimentation CA vers

12V CC, 1,5 A (En

fonction de votre

région)

Alimentatore CA

- 12V CC da 1,5 A

(in base al Paese di

vendita)

DX5e DSMX

5-Channel Transmitter

DX5e DSMX 5-Kanal

Sender

Emetteur DX5e DSMX

5 voies

DX5e DSMX

Trasmettitore 5 canali

DX6i DSMX 6-Channel

Transmitter

DX6i DSMX 6-Kanal

Sender

Emetteur DX6i DSMX

6 voies

DX6i DSMX

Trasmettitore 6 canali

DX7s DSMX

7-Channel Transmitter

Spektrum DX7s

7 Kanal Sender

Emetteur DX7s DSMX

7 voies

DX7s DSMX

Trasmettitore 7 canali

DX8 DSMX

Transmitter

Spektrum DX8 nur

Sender

Emetteur DX8 DSMX

8 voies

DX8 DSMX Solo

trasmettitore

DX9 DSMX

Transmitter

Spektrum DX9 nur

Sender

Emetteur DX9 DSMX

9 voies

DX9 DSMX Solo

trasmettitore

DX18 Transmitter Spektrum DX18 nur

Sender

Emetteur DX18 DSMX

9 voies

DX18 DSMX Solo

trasmettitore

E-ﬂ ite, AS3X, Blade, Celectra, UMX, DSM, DSM2, DSMX, ModelMatch, Bind-N-Fly, the Bind-N-Fly logo

and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, Inc.

The Spektrum trademark is used with permission of Bachmann Industries, Inc.

Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha

Corporation of Japan.

Aviat

, Aviat Aircraft™ and Pitts

are trademarks or registered trademarks of Aviat Aircraft, Inc.

and is used under license by Horizon Hobby, Inc.

Patents pending.

www.e-ﬂ iterc.com

Created 1/14 38313

EFLU5250

BNF UMX Pitts S-1S User manual

Brand: BNF

Model: UMX Pitts S-1S

Category: Remote controlled toys

Type: User manual

This manual is also suitable for

Download PDF

report

BNF UMX Pitts S-1S User manual

This manual is also suitable for

BNF UMX Pitts S-1S User manual

Related papers

Other documents