APC ACF126 Datasheet

APC
Brand
APC
Model
ACF126
Category
Rack accessories
Type
Datasheet

APC ACF126 is a duct kit for rack air removal unit that helps to remove hot air from the rack, which can improve the performance and lifespan of the equipment in the rack. The kit includes everything you need to install the duct, including plastic air manifolds, hoses, holder flanges, and screws. The duct can be cut to fit your specific configuration, and it can be attached to the ceiling using the included ceiling adapter. The duct kit is easy to install, and it can help to improve the airflow in your rack.

APC ACF126 is a duct kit for rack air removal unit that helps to remove hot air from the rack, which can improve the performance and lifespan of the equipment in the rack. The kit includes everything you need to install the duct, including plastic air manifolds, hoses, holder flanges, and screws. The duct can be cut to fit your specific configuration, and it can be attached to the ceiling using the included ceiling adapter. The duct kit is easy to install, and it can help to improve the airflow in your rack.

Duct Kit for Rack Air Removal Unit,
Installation—ACF126, ACF127
Inventory
Tools required
Installation
Support for the air manifolds
(1)
Plastic air manifolds
(4)
Hoses
(2)
Ceiling adapter (1)
ACF126—24 in
ACF127—600 mm
Holder flanges
(2)
M4 Phillips machine screws
(13)
Flange nuts
(6)
#2 Phillips screwdriver Utility knife Wire cutters Tape measure Hex nutdriver
Using wire cutters and a utility knife, cut the
hoses to fit your configuration. The length of the
hose should equal the distance from the top of
the plastic manifold to the ceiling, plus 6 in
(15.24 cm).
Thread a holder flange counterclockwise onto one end
of each hose and tighten by hand until it is firmly
secured. Do not overtighten.
na03 96b
na1722
Duct Kit for Rack Air Removal Unit, Installation—ACF126, ACF127
2 Air Duct Kit for the Rack Air Distribution Unit
Install the support for the air manifolds on the
frame of the Rack Air Removal Unit (ARU)
using 3 M4 machine screws.
Assemble each plastic air manifold. Fit 2 pieces
together, and secure them using two M4 machines
screws and flange nuts. Then secure the two manifolds
together.
Install the plastic air manifolds onto the support
for the air manifolds using 4 M4 machine
screws.
Attach the end of the each hose without a holder flange
to the ceiling adapter. Loosen the clamps on the ceiling
adapter and insert the end of the hose. Tighten the
clamps to securely hold the hose in place.
na 1813a
na1816a
na1815a
na1808a
Duct Kit for Rack Air Removal Unit, Installation—ACF126, ACF127
Air Duct Kit for the Rack Air Distribution Unit 3
Remove the ceiling tile directly above the unit
and save it for step 10. Install the ceiling adapter
in the opening.
Secure the ceiling adapter to the building’s structural
support (not the drop ceiling), using 10-gauge
(minimum) steel wire.
When using 2×4 ft ceilings tiles, insert a cross
member (not provided) for additional support.
When using 2×4 ft ceiling tiles, cut the tile removed in
step 7 to size, and install it to cover the opening.
Slide the holder flanges on the unattached ends
of the hoses over the air manifold sleeve, and
turn them clockwise to lock them into place.
na0414a
na0397a
na0394a
na03 95a
na1840a
*990-2773-001*
Entire contents copyright 2005 American Power Conversion Corporation. All rights reserved.
Reproduction in whole or in part without permission is prohibited. APC and the APC logo are
trademarks of American Power Conversion Corporation. All other trademarks, product names,
and corporate names are the property of their respective owners and are used for informational
purposes only.
990-2773-001 11/2005
APC Worldwide Customer Support
Customer support for this or any other APC product is available at no charge in any of the following ways:
• Visit the APC Web site to access documents in the APC Knowledge Base and to submit customer support requests.
– www.apc.com (Corporate Headquarters)
Connect to localized APC Web sites for specific countries, each of which provides customer support information.
– www.apc.com/support/
Global support searching APC Knowledge Base and using e-support.
• Contact an APC Customer Support center by telephone or e-mail.
– Regional centers:
– Local, country-specific centers: go to www.apc.com/support/contact for contact information.
Contact the APC representative or other distributor from whom you purchased your APC product for information on
how to obtain local customer support.
Direct InfraStruXure Customer Support Line
(1)(877)537-0607 (toll free)
APC headquarters U.S., Canada
(1)(800)800-4272 (toll free)
Latin America
(1)(401)789-5735 (USA)
Europe, Middle East, Africa (353)(91)702000 (Ireland)
Japan (0) 35434-2021
Australia, New Zealand, South Pacific area (61) (2) 9955 9366 (Australia)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

APC ACF126 Datasheet

APC
Brand
APC
Model
ACF126
Category
Rack accessories
Type
Datasheet

APC ACF126 is a duct kit for rack air removal unit that helps to remove hot air from the rack, which can improve the performance and lifespan of the equipment in the rack. The kit includes everything you need to install the duct, including plastic air manifolds, hoses, holder flanges, and screws. The duct can be cut to fit your specific configuration, and it can be attached to the ceiling using the included ceiling adapter. The duct kit is easy to install, and it can help to improve the airflow in your rack.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents