MQ Multiquip MP1-SERIES User manual

OPERATION AND PARTS MANUAL

P/N 25939

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

To find the latest revision of this

publication, visit our website at:

www.multiquip.com

MP1 SERIES

MODELS

MP1455H (5.5 HP GASOLINE)

MP1415E (1.5 HP ELECTRIC)

MP1420E (2.0 HP ELECTRIC)

MASONRY SAWS

Revision #3 (03/29/10)

PAGE 2 — MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10)

Engine exhaust and some of

its constituents, and some dust created

of California to cause cancer, birth

defects and other reproductive harm.

by power sanding, sawing, grinding,

drillingandotherconstructionactivities

contains chemicals known to the State

Some examples of these chemicals are:

Leadfromlead-basedpaints.

Crystallinesilicafrombricks.

Cementandothermasonryproducts.

Arsenicandchromiumfromchemically

treatedlumber.

Your risk from these exposures varies,

dependingonhowoftenyoudothistype

of work. To reduce your exposure to

these chemicals: work in aALWAYS

well ventilated area, and work with

approved safety equipment, such as

dust masks that are specially designed

to filter out microscopic particles.

PROPOSITION 65 WARNING

MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10) — PAGE 3

Grinding/cutting/drilling of masonry, concrete, metal and

other materials with silica in their composition may give

off dust or mists containing crystalline silica. Silica is a

basic component of sand, quartz, brick clay, granite and

numerous other minerals and rocks. Repeated and/or

substantial inhalation of airborne crystalline silica can

cause serious or fatal respiratory diseases, including

silicosis. In addition, California and some other

authorities have listed respirable crystalline silica as a

substance known to cause cancer. When cutting such

materials, always follow the respiratory precautions

mentioned above.

WARNING

Grinding/cutting/drilling of masonry, concrete, metal and

other materials can generate dust, mists and fumes

containing chemicals known to cause serious or fatal

injury or illness, such as respiratory disease, cancer,

birth defects or other reproductive harm. If you are

unfamiliar with the risks associated with the particular

process and/or material being cut or the composition of

the tool being used, review the material safety data

sheet and/or consult your employer, the material

manufacturer/supplier, governmental agencies such as

OSHA and NIOSH and other sources on hazardous

materials. California and some other authorities, for

instance, have published lists of substances known to

cause cancer, reproductive toxicity, or other harmful

effects.

Control dust, mist and fumes at the source where

possible. In this regard use good work practices and

follow the recommendations of the manufacturers or

suppliers, OSHA/NIOSH, and occupational and trade

associations. Water should be used for dust

suppression when wet cutting is feasible. When the

hazards from inhalation of dust, mists and fumes cannot

be eliminated, the operator and any bystanders should

always wear a respirator approved by NIOSH/MSHA for

the materials being used.

WARNING

SILICOSIS WARNING RESPIRATORY HAZARDS

SILICOSIS/RESPIRATORY WARNINGS

PAGE 4 — MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10)

TABLE OF CONTENTS

MP1 MASONRY SAW

Proposition 65 Warning ............................................. 2

Silicosis/Respiratory Warnings .................................. 3

Table Of Contents ..................................................... 4

Parts Ordering Procedures ....................................... 5

Safety Message Alert Symbols .............................. 6-7

Rules For Safe Operation .................................... 8-10

Operation and Safety Decals .................................. 11

Specifications .......................................................... 12

Dimensions ............................................................. 13

General Information ................................................ 14

Controls and Components ................................. 16-17

Electric Motor Components .................................... 18

Engine Components ............................................... 19

Pre-Setup (Electric) ............................................ 20-23

Pre-Setup (Gasoline) ......................................... 24-25

Operation (Electric) ............................................ 26-27

Operation (Electric) ............................................ 28-29

Maintenance ...................................................... 30-33

Electric Motor Wiring Diagram ................................ 34

Troubleshooting (Blade) .......................................... 36

Troubleshooting (Electric Motor) ............................. 37

Troubleshooting (Gasoline Engine) ................... 38-39

Explanation of Code In Remarks Column............... 40

Suggested Spare Parts ........................................... 41

MP1 COMPONENT

DRAWINGS

HONDA GX160K1QXC9

GASOLINE ENGINE

NOTE

MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10) — PAGE 5

PARTS ORDERING PROCEDURES

www.multiquip.com

Ordering parts has never been easier!

Choose from three easy options:

WE ACCEPT ALL MAJOR CREDIT CARDS!

When ordering parts, please supply:

R Dealer Account Number

R Dealer Name and Address

R Shipping Address (if different than billing address)

R Return Fax Number

R Applicable Model Number

R Quantity, Part Number and Description of Each Part

R Specify Preferred Method of Shipment:

UPS/Fed Ex DHL

N Priority One Tr u c k 

N Ground

N Next Day

N Second/Third Day

If you have an MQ Account, to obtain a Username

and Password, E-mail us at: parts@multiquip.

com.

To obtain an MQ Account, contact you

r

District Sales Manager for more information.

Order via Internet (Dealers Only):

Order parts on-line using Multiquip’s SmartEquip website!

N View Parts Diagrams

N Order Parts

N Print Speciﬁcation Information

Note: Discounts Are Subject To Change

Goto www.multiquip.com and click on

Order Parts

to log in and save!

Use the internet and qualify for a 5% Discount

on Standard orders for all orders which include

complete part numbers.*

Order via Fax (Dealers Only):

All customers are welcome to order parts via Fax.

Domestic (US) Customers dial:

1-800-6-PARTS-7 (800-672-7877)

Fax your order in and qualify for a 2% Discount

on Standard orders for all orders which include

complete part numbers.*

Order via Phone:

Domestic (US) Dealers Call:

1-800-427-1244

Best Deal!

International Customers should contact

their local Multiquip Representatives for

Parts Ordering information.

Non-Dealer Customers:

Contact your local Multiquip Dealer for

parts or call 800-427-1244 for help in

locating a dealer near you.

Note: Discounts Are Subject To Change

Effective:

January 1

st

, 2006

NOTICE

All orders are treated as Standard Orders and will

ship the same day if received prior to 3PM PST.

PAGE 6 — MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10)

Safety precautions should be followed at all times when operating

this equipment. Failure to read and understand the Safety

Messages and Operating Instructions could result in injury to

yourself and others.

FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

This Owner's Manual has been

developed to provide complete

instructions for the safe and

efficient operation of the

MULTIQUIP MP1

Before using this MASONRY SAW, ensure that the operating

individual has read and understands all instructions in this

manual.

SAFETY MESSAGE ALERT SYMBOLS

DANGER

WARNING CAUTION

DANGER: WILL KILLED

DO NOT

WARNING: CAN KILLED

DO NOT

CAUTION: CAN

DO NOT

HAZARD SYMBOLS

Hazard Symbols

Message Alert Symbols

Burn Hazards

DO NOT

NEVER

Rotating Parts

NEVER

hands hair

clothing

Guards and Covers In Place

NEVER

Rotating Blade

Accidental Starting

ALWAYS ON/OFF

OFF

NOTE

SAFETY MESSAGE ALERT SYMBOLS

MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10) — PAGE 7

Over Speed Conditions

NEVER

Respiratory Hazard

ALWAYS

Sight and Hearing hazard

Equipment Damage Messages

NEVER

DO

NOT

DO NOT

NEVER

Explosive Fuel

Lethal Exhaust Gases

HAZARD SYMBOLS - Gasoline Powered Models

This

saw

, other property, or the

surrounding environment could be

damaged if you do not follow

instructions.

NOTE

SAFETY MESSAGE ALERT SYMBOLS

PAGE 8 — MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10)

RULES FOR SAFE OPERATION

CAUTION:

Failure to follow instructions in this manual may

lead to serious injury or even death! This

equipment is to be operated by trained and

qualified personnel only! This equipment is

for industrial use only.

The following safety guidelines should always be used when

operating the MP1 SAW. Unless otherwise noted, these

guidelines refer to saws with gasoline powered engines.

SAFETY

■

DO NOT operate or service this equipment

before reading this entire manual.

■

This equipment should not be operated by

persons under 18 years of age.

■

NEVER operate the saw without proper protective

clothing, shatterproof glasses, steel-toed boots

and other protective devices required by the job.

■

NEVER operate this equipment when not

feeling well due to fatigue, illness or taking

medicine.

■

NEVER operate the saw under the

influence or drugs or alcohol.

■

NEVER use accessories or attachments,

which are not recommended by Multiquip

for this equipment. Damage to the equipment and/or injury to

user may result.

■

Manufacturer does not assume responsibility for any accident

due to equipment modifications. Unauthorized equipment

modification will void all warranties.

■

Whenever necessary, replace nameplate, operation and

safety decals when they become difficult read.

■

ALWAYS check the saw for loosened threads or bolts before

starting.

■

NEVER operate the saw in an explosive atmosphere where

fumes are present or near combustible materials. An explosion

or fire could result causing severe

bodily harm or even

death.

■

NEVER use fuel as a cleaning agent.

■

ALWAYS use extreme caution when

working with flammable liquids. When

refueling, stop the engine and allow it to cool.

■

NEVER

smoke

around or near the

machine. Fire or explosion could result from

fuel vapors

, or if fuel is spilled on a

hot!

engine.

■

Topping-off to filler port is dangerous, as it tends to spill fuel.

■

ALWAYS service air cleaner frequently to prevent carburetor

malfunction.

■

NEVER run the engine without the air filter. Severe engine

damage could occur. (Gasoline powered engines)

■

NEVER touch the hot exhaust

manifold, muffler or cylinder. Allow

these parts to cool before servicing

the saw.

■

The engine of this saw (

gasoline model only

) requires an

adequate free flow of cooling air. NEVER operate the saw in

any enclosed or narrow area

where free flow of the air is

restricted. If the air flow is

restricted it will cause serious

damage to the saw's engine

and may cause injury to

people. Remember the

saw's engine gives off

DEADLY

carbon monoxide

gas.

■

ALWAYS stop the engine before servicing, adding fuel and

oil.

■

High Temperatures – Allow the engine to cool before adding

fuel or performing service and maintenance functions. Contact

with

hot!

components can cause serious burns.

■

ALWAYS refuel in a well-ventilated

area, away from sparks and open

flames.

SAFETY - GASOLINE POWERED ENGINES

MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10) — PAGE 9

BLADE SAFETY

■

Use appropriate blades manufactured for use on masonry

saws.

■

Always inspect blades before each

use. The blade should exhibit no

cracks, dings, or flaws in the steel

centered core and/or rim. Center

(arbor) hole must be undamaged and

true.

■

Examine blade flanges for damage, excessive wear and

cleanliness before mounting blade. Blade should fit snugly

on the shaft and against the inside/outside blade flanges.

■

Ensure the blade is marked with an operating speed greater

than the blade shaft speed of the saw.

■

Only cut the material that is specified by the blade. Read the

specifications of the blade to ensure the proper tool has been

matched to the material being cut.

■

Always keep blade guards in place.

Exposure of the blade must not

exceed 180 degrees.

■

NEVER touch or try to stop a moving

blade with your hands. ALWAYS

keep hands clear of the blade.

■

Ensure that the blade does not come

into contact with the ground or surface

during transportation. DO NOT drop the blade on ground or

surface.

■

The engine governor is designed to permit maximum engine

speed in a no-load condition. Speeds that exceed this limit

may cause the blade to exceed the maximum safe allowable

speed.

■

Ensure that the blade is mounted for proper operating

direction.

■

Keep all inexperienced and unauthorized people away from

the equipment at all times.

■

ALWAYS use or operate the saw on a level surface to prevent

the saw from tipping.

GENERAL SAFETY

■

ALWAYS read, understand, and follow procedures in

Operator's Manual before attempting to operate equipment.

■

ALWAYS be sure the operator is familiar with proper safety

precautions and operating techniques before using the saw.

■

NEVER leave the machine

unattended

while running.

■

Block the unit when leaving or when using on a slope.

■

ALWAYS check to make sure that the operating area is clear

before starting the engine.

■

Maintain this equipment in a safe operating condition at all

times.

■

AVOID wearing jewelry or loose fitting clothing that may snag

on the controls or moving parts, this can cause a serious

injury.

■

ALWAYS keep clear of

rotating

or

moving parts

while

operating or the saw.

■

ALWAYS store equipment properly when it is not being used.

Equipment should be stored in a clean, dry location out of

the reach of children.

■

NEVER use accessories or attachments which are not

recommended by the manufacturer for this equipment.

Damage to the equipment and/or injury to user may result.

WARNING

■

ALWAYS check to make sure that the

operating area is clear before starting the

engine.

WARNING

SAFETY - ELECTRIC POWERED MODELS

■

ALWAYS connect the motor to a power source in compliance

with all local electrical codes. This must be performed by a

qualified electrician.

■

ALWAYS use only outdoor approved GROUNDED extension

cords.

■

MAKE CERTAIN the power cord/extension cord is free from

damage and that the grounding circuit is operational.

■

MAKE CERTAIN the extension cord used is intended to be

used in the environment you will be using it in. If an extension

is used, NEVER submerge the connection in water. To reduce

the risk of electrical shock, always make water-tight

connections.

■

MAKE CERTAIN the "ON/OFF" switch is in the "OFF" position

before plugging in the power cord/extension cord to avoid

accidental starting.

■

ALWAYS stop the motor before servicing. MAKE CERTAIN

the motor is stopped and turned "OFF" at the switch, and the

power cord is disconnected from the power source.

■

Use only the guage wire and length of cord recommended

for the motor size.

■

When cutting, ALWAYS be aware of the location of the cord.

RULES FOR SAFE OPERATION

PAGE 10 — MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10)

RULES FOR SAFE OPERATION

EMERGENCIES

■

ALWAYS know the

location of the nearest

fire extinguisher

.

■

ALWAYS know the location of the

nearest and

first aid kit

.

■

always

know the location of the

nearest phone or

keep a phone on the job site

.

Also know the phone numbers of the nearest

ambulance

,

doctor

and

fire department

. This

information will be invaluable in the case of an

emergency.

SAW TRANSPORTATION SAFETY

■

Use an appropriate lifting equipment to ensure the safe

movement of the saw.

■

DO NOT use the handles as lifting points.

■

Safeguard against extreme saw attitudes relative to level.

An engine tipped to extreme angles may cause oil to gravitate

into the cylinder head making the engine start difficult.

(Gasoline powered engines)

■

NEVER transport the saw with the blade mounted.

SAW MAINTENANCE (CLEANING)

■

ALWAYS clean the saw before maintenance or repair.

■

DO NOT use aggressive cleaners (i.e. containing solvents).

DO NOT use high pressure water jets, aggressive detergents

or solutions and liquids with a temperature exceeding 86 F.

Use a fluff-free cloth only.

■

Use a cloth which may be lightly moistened only for removing

dust and dirt. Hard packed dirt can be removed with a

soft

brush.

■

NEVER let water, cleaning liquid or vapor penetrate into the

electric motor, connectors, plugs, and switches. When

cleaning cover all apertures or openings on all electrical

components.

■

ALWAYS use a soft, low-pressure water jet and a brush to

rinse dirt and incrustations away. Be particularly careful not

to spray water on sensitive parts of of the saw (e.g. electric

motor, ON/OFF switch). Clean the motor and ON/OFF switch

by wiping with a

moist

cloth.

■

DO NOT rinse the bearings of the drive elements (gasoline

model only).

MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10) — PAGE 11

NOTES

PAGE 12 — MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10)

DANGER

SPECIFICATIONS (SAW/ENGINE)

ELBATWAS1PM.1SNOITACIFICEPS

snoisnemiD

)mc85.86xmc28.38xmc521.111("72x"33x"57.34

thgieWetamixorppA

).gK57(.sbl561

deepSrotoMcirtcelE

)2elbaTeeS(MPR0543

deepSedalB

MPR8852

pmuPretaW

detcetorpyllamrehT,zH06/V511

)enilosaG(enignE

)2elbaTeeS(adnoH,delooCriA,rednilyCelgniS,elcyc4PH5.5

deepSedalB

MPR0082

pmuPretaW

205-70852tiKlanoitpO

LARENEG

yticapaCedalB

mumixamedalb.ni41

htpeDgnittuC

edalb.ni41htiw.ni5

SNOITACIFICEPSENIGNESAG/ROTOMCIRTCELE1PM.2ELBAT

ledoMwaS PH5541PM E5141PM E0241PM

rotoM/enignE 9CXQ1K061XGadnoH

.P.H5.1

cirtcelEytuDyvaeH

V032/511

esahPelgniS

zH06

egatloVlauD

.L.FspmA

6.8/2.71

.P.H0.2

cirtcelEytuDyvaeH

V032/511

esahPelgniS

zH06

egatloVlauD

.L.FspmA

4.8/8.61

epyT rednilyCelgniSVHOekortS-4

ekortS&eroB )mm54x86(.ni8.1x7.2

tnemecalpsiD )cc361(.ni.uc9.9

tuptuOxaM mpr0063@)WK0.4(phb4.5

.paCknaTleuF )sretil6.3(.laG.S.U59.0

leuF enilosaGdedaelnU

.paCliOebuL )sretil06.0(.tQ.S.U36.0

lortnoCdeepS

dohteM

epytthgieW-ylFlagufirtneC

dohteMgnitratS tratSlioceR

noisnemiD

.nI2.31x3.41x0.21

)mm533x263x403(

thgieWteNyrD )gK0.51(.sbL1.33

MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10) — PAGE 13

DIMENSIONS

Figure 1. Dimensions

SNOISNEMID.3ELBAT

.FERSNOISNEMID

A

)rotomcirtcele(

)mc47(.ni0.92

A

)enigneenilosag(

)mc47(.ni0.92

B)mc601(.ni0.24

C)mc6.85(.ni0.72

D)mc79.31(.ni5.5

E)mc8.63(.ni5.41

F)mc2.92(.ni5.11

G)sretem53.6(.ni5.2

H)sretem2.84(.ni0.91

PAGE 14 — MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10)

GENERAL INFORMATION

MP1 MASONRY SAW

The MP1 masonry saw is designed for vigorous wet-cutting

masonry applications. The heavy-duty aluminum conveyor cart

and ball bearing roller wheels ensure material stability and

smooth travel. In addition a reinforced jig-welded steel frame

provides rigidity for cutting accuracy and long service life.

This saw is available with either an

electric motor

or a

gasoline

engine

. The heavy duty electric motors are available in either

1.5 HP or 2.0 HP with overload protection. Each motor can

operate at either 115 VAC or 230 VAC. The electric motor input

voltage is selectable by means of a toggle switch. Always make

sure that the input voltage being supplied to the motor matches

the position of the voltage selector toggle switch located on top

of the motor.

If desired, the MP1 saw can be configured with a 5.5 HP Honda

GX160 gasoline engine.

All MP1 models include a high flow water pump, cutting jig, water

hoses and associated plumbing to enable the operator to begin

wet cutting.

DRY CUTTING APPLICATIONS

The MP1 masonry saw is shipped from the factory for wet-cutting

saw applications, however it can be used for dry-cutting saw

applications (see dry-cutting saw applications in this manual).

The most import thing to remember is to

disconnect the water

pump

. The water pump is cooled by the flow of water, and

failure to disconnect the pump (when running dry) will cause

pump failure. NEVER! have the water pump engaged when dry

cutting applications are involved.

BLADE APPLICATIONS

This saw has been designed to incorporate the use of Diamond

Blades

™

as the cutting tool. The optimum performance of this

saw is best evidenced by using 14-inch (356 mm) Diamond

Blades

™

that match the material being cut. Ask your dealer, or

call MULTIQUIP about your specific cutting application.

OVERVIEW OF FEATURES

■

1.5 or 2.0 HP, 115/230 VAC , 60 Hz heavy duty electric motors

with overload protection.

■

5.5 HP Honda GX160 gasoline engine.

■

14-inch blade capacity provides 5-inch depth of cut.

■

Rugged aluminum conveyor cart for optimum stability.

■

Open back design permits capability of cutting large

materials.

■

Ergonomically designed cutting head provides operator

relief in high tempo operations.

■

Mounted carrying handles for easy transportation.

■

Rubber-matted cutting table helps hold the material being

cut in place while resisting vibrations for smoother cuts with

less chipping.

■

Cutting table marked in inches and centimeters (ruler) for

precision cuts.

■

Stay-level blade guard for operator safety.

■

Rigid steel frame minimizes vibrations and assures accurate

cutting.

■

Mechanical Water Pump Kit (Gasoline Model Only)

■

Electric Submersible Water Pump Kit (Electric Models Only).

ACCESSORIES/REPLACEMENT PARTS

If desired the MP1 masonry saw can be equipped with a scissors

type support stand P/N TRAK14SS, this stand is ideal when the

saw needs to be transported and placed on a secure reliable

platform.

MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10) — PAGE 15

NOTES

PAGE 16 — MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10)

CONTROLS AND COMPONENTS

Figure 2. MP1 Saw (Electric/Gasoline)

MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10) — PAGE 17

1. Ruler Backstop – When cutting, place material against

backstop. Use measurement rail (ruler) to determine where

material is to be cut.

2. Water Tray – When wet cutting is required, fill with clean

fresh water. Make sure submersible is totally immersed in

water.

3. Cutting Head Handle – Grab hold of this handle to move

the cutting blade head either

up

or down. To move the

cutting head, release the mounting plate release/lock lever.

4. Carrying Handle (Head) – Grip this handle (front) to lift

the mounting plate.

5. Blade Guard – Protects the user from the cutting blade.

NEVER

operate the saw with the blade guard removed.

6. Power ON/OFF Box – This box is used on

electric

models

saws only

. To turn on the saw place in the ON

position. Place in the OFF position to shut-down the saw.

7. V-belt Cover – Remove this cover to access the drive V-

belt.

NEVER

operate the saw with the V-belt cover removed.

8. Mounting Plate Release/Lock Lever – Push this lever

backwards to release

the mounting plate. This will allow

the cutting head to move either up or down. Push the lever

forward to lock

the mounting plate in place.

9. Electric Motor/Conduit Box– This unit uses 2 different

types of electric motors and voltages (see Table 2). Always

make sure the voltage selector switch has been set to the

correct position for the voltage being supplied to the motor.

Plug the water pump (electric models only) power cord

into the AC receptacle located on the conduit box.

10. Mounting Plate – Supports the electric motor/gasoline

engine. Plate has slotted holes for horizontal (right-side)

and vertical (left-side) adjustment of cutting head.

11. Carrying Handle (Head) – Grip this handle (rear) to lift

the mounting plate.

12 . Tie Rod – The tie rod length has been set at the factory for

best blade guard position for the majority of the cutting that

will be done.

13. Spring Tensioner – Allows for an easy up and down

movement of the mounting plate.

14. Mounting Plate Lock/Release Knobs – Turn knob (2)

clockwise to release the mounting plate. Turn counter-

clockwise to tighten.

15. Stopper – Place stopper in tray when filling with water.

16. Carrying Handle (Tray) – Grip this handle (right-side) to

trasport the saw.

17. Electric Water Pump – For best results place the pump

between the splash shield and the rear of the water tray.

This is for electric models only. Plug water pump power

cord into AC receptacle on electric motor conduit box.

NEVER

run pump dry. Pump must be immersed in water.

18. Spindle Bolt/Outside Blade Flange – When mounting

of the cutting blade is required, remove the spindle bolt

and outside blade flange. Align cutting blade with inside

flange arbor and reassemble spindle and outside blade

flange.

19. Splash Guard – Keeps water and debris from leaving the

water tray.

20. Carrying Handle (Tray) – Grip this handle (left-side) to

trasport the saw.

21. Mechanical Water Pump – This pump is used on gasoline

models only. Saw is shipped from the factor for wet cutting

applications (pump handle down). Place pump handle

upwards to disengage pump.

NEVER

run pump dry.

22. Engine – The gasoline model saws uses a 5.5 HP Honda

GX160, 4-stroke, OHV, single cylinder, air cooled gasoline

engine.

23. V-belt Cover (Gasoline Only) – Remove this cover to

access the engine shaft-side V-belt.

NEVER

operate the

saw with the V-belt cover removed.

24. Water Lines – Replace the clear vinyl tubing water lines

when they become brittle, worn or clogged. Water kits are

available through your dealer.

25. Priming Bulb – Squeeze this bulb to prime the mechanical

water pump (gasoline models only).

26. Blade Wrench – Use this tool to mount and remove cutting

blade.

27. Strainer – For best results place the strainer between the

splash shield and the rear of the water tray. This is for

gasoline models only.

NEVER

run pump dry. Strainer must

be immersed in water.

28. Miter Box – For angled cuts, place the lip of the miter box

on the measurement rail with the threaded thumb knob

facing you and tighten.

Figure 2 shows the location of the basic controls or components

for the MP1 saw. Listed below is a brief explanation of each

control or component.

CONTROLS AND COMPONENTS

PAGE 18 — MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10)

MP1 — ELECTRIC MOTOR COMPONENTS

Figure 3. Electric Motor Components

MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10) — PAGE 19

Figure 4. Engine Controls and Components

INITIAL SERVICING-GASOLINE ENGINE

The engine (Figure 4) must be checked for proper lubrication and

filled with fuel prior to operation. Refer to the manufacturers engine

manual for instructions & details of operation and servicing.

1. Fuel Filler Cap – Remove this cap to add unleaded

gasoline to the fuel tank. Make sure cap is tightened

securely. DO NOT over fill.

7. Air Cleaner – Prevents dirt and other debris from entering

the fuel system. Remove wing-nut on top of air filter

cannister to gain access to filter element.

.

DANGER

WARNING

Adding fuel to the tank should be done only when

the engine is stopped and has had an opportunity

to cool down. In the event of a fuel spill, DO NOT

attempt to start the engine until the fuel residue has been completely

wiped up, and the area surrounding the engine is dry.

2. Throttle Lever – Used to adjust engine RPM speed (lever

advanced forward

SLOW

, lever back toward operator

FAST

).

3. Engine ON/OFF Switch – ON position permits engine

starting, OFF position stops engine operations.

4. Recoil Starter (pull rope) – Manual-starting method. Pull

the starter grip until resistance is felt, then pull briskly and

smoothly.

5. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop

the flow of fuel.

6. Choke Lever – Used in the starting of a cold engine, or in

cold weather conditions. The choke enriches the fuel

mixture.

MP1 — ENGINE COMPONENTS

11. Oil Drain Bolt – Drain used oil while the engine is warm.

12. Oil Level Cap and Dipstick – Check engine oil with

engine stopped and in a level position.

10. Fuel Tank – Holds unleaded gasoline. For additional

information refer to engine owner's manual.

Engine components can generate extreme heat.

To prevent burns, DO NOT touch these areas

while the engine is running or immediately after

operating. NEVER operate the engine with the muffler removed.

NOTE

Operating the engine without an

air filter, with a damaged air filter,

or a filter in need of replacement

will allow dirt to enter the engine,

causing rapid engine wear.

8. Spark Plug – Provides spark to the ignition system. Set

spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean

spark plug once a month.

9. Muffler – Used to reduce noise and emissions

PAGE 20 — MP1 — OPERATION AND PARTS MANUAL — REV. #3 (03/29/10)

Whenever cleaning, adjusting or lubricating any part of the saw,

MAKE CERTAIN to place the power ON/OFF switch in the OFF

position and disconnect the plug from the power source.

PRE-SETUP (ELECTRIC)

Assembly (Electric Powered Saws Only)

1. Open the shipping container carefully, lift the saw by its carrying

handles and place it on a suitable table or platform. Make sure

the table or platform can support the weight of the saw. The

saw platform should be rigid and stationary so that it will not

move, sag, or sway due to the vibrations and movements of

the saw.

2. If using the MP1 series

support stand kit

(P/N TRAK14SS),

attach stand to the under-side of the water tray. Follow the

instructions supplied with the support stand kit when attaching

it to the water tray.

3. Attach the clear plastic water hose (Figure 5) coming from the

blade guard to the water pump.

4. Fill the water tray with

clean fresh water

. The

water

pump

intake must always be fully covered by water

. Also,

keep the pump intake free of sludge, debris and other

materials that may accumulate in the tray.

5. Make certain that the water hose will not come in contact

with the blade or interfere with any moving parts. The best

location for the water pump/strainer is between the splash

shield and the rear of the water tray. This will prevent some

of the abrasive particles from flowing through the pump.

6. Insert the water pump

power plug

into the outlet receptacle

on the electric motor conduit box as shown in Figure 6.

CONVEYOR CART PLACEMENT

1. Place the conveyor cart across the water tray as shown in

Figure 7. Align the wheels of the cart with the outer edge of the

water tray. Push the cart back and forth, it should move freely in

both directions.

Figure 5. Water Tray/Water Pump

Figure 6. Water Pump Power Connection

Figure 7. Conveyor Cart Placement

PRE-SETUP

WARNING

Page is loading ...

MQ Multiquip MP1-SERIES User manual

This manual is also suitable for

MQ Multiquip MP1-SERIES User manual

Related papers

Other documents