Saeco HD8753/15 Operating instructions

Register your product and get support at

www.philips.com/welcome

EN

02

English

Type HD8753

OPERATING INSTRUCTIONS

READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE MACHINE.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be

followed, including the following:

1. Read all instructions.

2. Do not touch hot surfaces. Use handles or knobs.

3. To protect against fire, electric shock and injury to persons do not immerse

cord, plugs, or appliance in water or other liquid.

4. Close supervision is necessary when the appliance is used by or near

children.

5. Unplug from outlet when not in use and before cleaning. Allow to cool

before putting on or taking off parts, and before cleaning the appliance.

6. Do not operate any appliance with a damaged cord or plug or after the

appliance malfunctions, or has been damaged in any manner. Return

appliance to the nearest authorized service facility for examination, repair

or adjustment.

7. The use of accessory attachments not recommended by the appliance

manufacturer may result in fire, electric shock or injury to persons.

8. Do not use outdoors.

9. Do not let cord hang over edge of table or counter, or touch hot surfaces.

10. Do not place on or near a hot gas or electric burner, or in a heated oven.

11. Always attach plug to appliance first, then plug cord into wall outlet. To

disconnect, turn any control to “off”, then remove plug from wall outlet.

12. Do not use appliance for other than intended use.

13. Save these instructions.

SAVE THESE INSTRUCTIONS

CAUTION

This appliance is for household use only. Any servicing, other than cleaning

and user maintenance, should be performed by an authorized service center.

Do not immerse machine in water. To reduce the risk of fire or electric shock,

do not disassemble the machine. There are no parts inside the machine

serviceable by the user. Repair should be done by authorized service personnel

only.

1. Check voltage to be sure that the voltage indicated on the nameplate

corresponds with your voltage.

2. Never use warm or hot water to fill the water tank. Use cold water only.

3. Keep your hands and the cord away from hot parts of the appliance during

operation.

4. Never clean with scrubbing powders or harsh cleaners. Simply use a soft

cloth dampened with water.

5. For optimal taste of your coffee, use purified or bottled water. Periodic

descaling is still recommended every 2-3 months.

6. Do not use caramelized or flavored coffee beans.

INSTRUCTIONS FOR THE POWER

SUPPLY CORD

A. A short power-supply cord (or detachable power-supply cord) is to be

provided to reduce risks resulting from becoming entangled in or tripping

over a longer cord.

B. Longer detachable power-supply cords or extension cords are available

and may used if care is exercised in their use.

C. If a long detachable power-supply cord or extension cord is used,

1. The marked electrical rating of the detachable power-supply cord or

extension cord should be at least as great as the electrical rating of the

appliance

2. If the appliance is of the grounded type, the extension cord should be a

grounding-type 3-wire cord, and

3. The longer cord should be arranged so that it will not drape over the

counter top or table top where it can be pulled on by children or tripped

over.

2

1

31

32

21

22

20

17

19

23

18

12 3

1110 12 13 14

4

5

6

7

8

9

24 27

15

25 28

26 29

30

16

3

Table of Contents

Introduction .................................................................................................... 4

General Description ( g.1) ............................................................................... 4

Important ....................................................................................................... 5

Intended Use .............................................................................................................................................5

Power Supply - Power Cord .......................................................................................................................5

For the Safety of Others .............................................................................................................................5

Danger of Burns ........................................................................................................................................5

Machine Location - Suitable Location for Operation and Maintenance ......................................................6

Cleaning and Storing the Machine ............................................................................................................6

Malfunction ..............................................................................................................................................6

Fire Safety Precautions ..............................................................................................................................6

First Use .......................................................................................................... 7

Packaging .................................................................................................................................................7

Preliminary Operations .............................................................................................................................7

Circuit Priming ..........................................................................................................................................9

Rinse/Self-Cleaning Cycle ........................................................................................................................10

For a perfect Espresso: Rinse the co ee circuit if using the machine for the  rst time or after a long

period of inactivity. .................................................................................................................................10

Measuring Water Hardness ..............................................................................12

"INTENZA+" Water Filter (Optional) ..................................................................13

"INTENZA+" Water Filter Installation .....................................................................................................13

Espresso Co ee: Brewing and Adjustments .......................................................15

Pre-brewing Technology: Enhancing the Aroma......................................................................................15

Adjustable Ceramic Co ee Grinder: A Full Aroma Preservation ................................................................15

"Aroma" Adjustment: Select Your Favourite Amount ...............................................................................16

Brewing Co ee ...............................................................................................17

Adjusting the Dispensing Spout ..............................................................................................................17

Using Co ee Beans ..................................................................................................................................18

Using Pre-ground Co ee .........................................................................................................................18

Adjusting the Co ee Length (MEMO Function) .......................................................................................19

Milk Carafe .....................................................................................................20

Filling the Milk Carafe .............................................................................................................................20

Inserting the Milk Carafe .........................................................................................................................21

Removing the Milk Carafe .......................................................................................................................22

Emptying the Milk Carafe ........................................................................................................................22

Cappuccino .....................................................................................................23

Adjusting the Cappuccino Length (MEMO Function) ...............................................................................24

Hot Milk .........................................................................................................25

Adjusting the Amount of Hot Milk in the Cup (MEMO Function) ..............................................................26

Hot Water Dispensing .....................................................................................27

Eco-friendly: Stand-by .....................................................................................28

Stand-by .................................................................................................................................................28

Cleaning and Maintenance ..............................................................................29

General Cleaning .....................................................................................................................................29

Cleaning the Milk Carafe (After Each Use)................................................................................................31

Weekly Cleaning of the Carafe (Carafe Lid) ..............................................................................................32

Monthly Cleaning of the Carafe (Thorough Cleaning) ..............................................................................35

Brew Group ....................................................................................................37

Weekly Cleaning - Brew Group ................................................................................................................37

Brew Group Cleaning with "Co ee Clean Tablets" ...................................................................................39

Brew Group Lubrication ..........................................................................................................................41

Descaling .......................................................................................................42

Programming .................................................................................................46

Enter the “Menu” .....................................................................................................................................46

Programming Controls ............................................................................................................................47

Exiting the Programming Mode ..............................................................................................................47

Functions ................................................................................................................................................48

Programming Example ...........................................................................................................................48

Control Panel Display ......................................................................................50

Troubleshooting .............................................................................................52

Technical Speci cations ..................................................................................53

Service ...........................................................................................................56

4

ENGLISH

Introduction

Congratulations on your purchase and welcome to Philips SAECO!

To fully bene t from the support that Philips o ers, register your product at

www.philips.com/welcome.

In this user manual you will  nd all the information you need to install, use,

clean and descale your appliance. In case you need further support, please

contact the toll free Philips consumer care help line. You can  nd the phone

number on the last page of this document and in the warranty booklet sup-

plied with the appliance.

General Description ( g.1)

1. Grinder adjustment knob

2. Pre-ground co ee compartment

3. Co ee bean hopper

4. Co ee bean hopper lid

5. Control panel

6. Dispensing spout

7. Full drip tray indicator

8. Cup holder grill

9. Drip tray

10. Water dispensing spout (removable)

11. Co ee grounds drawer

12. Brew group

13. Co ee residues drawer

14. Service door

15. Milk carafe

16. Water tank

17. Power cord socket

18. Power button

19. Co ee grinder adjustment key + Pre-ground co ee doser

20. Cleaning brush

21. Grease for the brew group

22. Power cord

23. Water hardness test

24. Espresso co ee brew button

25. Long Espresso brew button

26. Special beverages selection button

27. ON/OFF button

28. "Aroma" - Pre-ground co ee button

29. "MENU" button

30. Cappuccino brew button

31. Descaling solution

32.

Filter (INTENZA+) - Optional

ENGLISH

5

Important

Read this user manual carefully before using the appliance and save it for

future reference.

Never allow water to come into contact with any of the electrical parts of

the machine: Danger of short circuit! Steam and hot water may cause bur-

ning! Never direct the hot water jet towards body parts: Danger of burning!

Intended Use

The co ee machine is intended for domestic use only. Do not make any

technical changes or use the machine for unauthorised purposes since this

would create serious hazards! The appliance is not to be used by persons

(including children) with reduced physical, mental or sensory abilities or

with scarce experience and/or expertise, unless they are supervised by a

person responsible for their safety, or they are instructed by this person on

how to properly use the machine.

Power Supply - Power Cord

Only connect the co ee machine to a suitable socket. The socket to which

the machine is connected must be:

- Compatible with the type of plug installed on the machine;

- Sized to comply with the data on the tag attached to the appliance;

- Connected to an e cient earthing system.

Never use the co ee machine if the power cord is defective or damaged.

If the power cord is damaged, it must be replaced by the manufacturer or

by its authorised service centre.

Do not pass the power cord around corners, over sharp edges or over hot

objects and keep it away from oil.

Do not use the power cord to carry or pull the co ee machine.

Do not pull out the plug by the power cord or touch it with wet hands. Do

not let the power cord hang freely from tables or shelves.

For the Safety of Others

Prevent children from playing with the machine. Children are not aware

of the risks related to electrical household appliances. Do not leave the

machine packaging materials within the reach of children.

Danger of Burns

Never direct the jet of hot steam and/or hot water towards yourself or oth-

ers: Danger of burning!

6

ENGLISH

Machine Location - Suitable Location for Operation and Mainte-

nance

For best use, it is recommended to:

• Choose a safe, level surface, where there will be no danger of overtur-

ning the appliance or being injured;

• Choose a location that is su ciently well-lit, clean and near an easily

reachable socket;

• Provide for a minimum distance from the sides of the machine as

shown in the illustration

;

• While switching on or o the machine, we suggest placing an empty

glass under the dispensing spout.

Do not keep the machine at temperatures below 0°C. Frost may damage

the machine. Do not use the co ee machine outdoors.

In order to prevent its housing from melting or being damaged, do not

place the machine on very hot surfaces and close to open  ames.

Cleaning and Storing the Machine

Keep the machine at its best, clean and store it properly.

Since the machine uses natural ingredients to brew beverages (co ee

beans, water, milk, etc.), some residues of ground co ee or condensed wa-

ter could be present on its supporting surface. For this reason we recom-

mend to periodically clean both the visible parts of the machine and the

area beneath it.

Before storing the machine we strongly recommend to clean it:

- Water left in the tank and/or in the water circuit for several days should

not be consumed. If the machine is going to remain inactive for a long

time, dispense water as described in the “Hot Water Dispensing” sec-

tion.

- Turn o the power button and clean the machine. Finally, remove the

plug from the socket. Wait for the machine to cool down.

Never immerse the machine in water! Store it in a dry place, out of the

reach of children. Keep it protected from dust and dirt.

It is strictly forbidden to tamper with the internal parts of the machine.

Malfunction

In case of failure, problems or a suspected fault resulting from the falling of

the machine, immediately remove the plug from the socket. Never attempt

to operate a faulty machine.

For further information on troubleshooting and service, please refer to the

"Troubleshooting" and "Service" chapters.

Fire Safety Precautions

In case of  re, use carbon dioxide (CO

2

) extinguishers. Do not use water or

dry powder extinguishers.

ENGLISH

7

First Use

Packaging

The original package has been designed and constructed to protect the

machine during transport. We recommend keeping the packaging material

for possible future transport.

Preliminary Operations

Remove the drip tray with cup holder grill and the co ee machine from

the package. Place the machine in a place that meets the requirements

described in the safety regulations.

1

Insert the grill drip tray into the seat in the machine. Make sure the tray

is fully inserted into position. The tray must be clipped into to the

machine.

Important Note:

- Insert the plug into the socket only when indicated and make sure the

power button is on "0".

- Carefully read the explanations of all the warnings the machine displays

to the user on the control panel LCD display (“LCD Display Warnings”

chapter).

NEVER remove the drip tray when the machine is on. Wait for a couple of

minutes after turning on/o , as the machine will be carrying out a rinse/

self-cleaning cycle (see section "Rinse/Self-Cleaning Cycle").

2

Remove the water tank from its seat.

3

Rinse and  ll it with fresh water, making sure that the (MAX) level indi-

cated in the tank is not exceeded. Completely reinsert the tank into the

designated seat pushing all the way to the end (the external pro les

must match).

Fill the tank only with fresh, non-sparkling water. Hot water or any other

liquid may damage the tank and/or the machine. Do not operate the ma-

chine without water. Make sure there is enough water in the tank.

8

ENGLISH

4

Remove the co ee bean hopper lid.

Note: The hopper may be provided with di erent safety features according to

the regulations applicable in the country of use of the machine.

5

Slowly pour the co ee beans into the hopper.

Only co ee beans must be put into the co ee bean hopper. If ground

co ee, instant co ee or any other object is put in the co ee bean hopper, it

may damage the machine.

6

Reposition the co ee bean hopper lid.

7

Insert the plug into the socket on the back of the machine.

8

Insert the plug of the other end of the cable into a wall socket with

suitable power voltage.

1

2

9

Switch the power button to "I" to turn on the machine.

Black

The display shows the Stand-by icon.

10

To turn on the machine simply press the " " button.

ENGLISH

9

YellowYellow

The display indicates that the circuit must be primed.

Circuit Priming

In order to avoid that any water is left in the circuit for a long time, before

starting the machine for the  rst time, and after long periods of inactivity,

the water circuit needs to be primed. This is because we want to o er you a

perfect and fresh product.

1

Select "START" by pressing the " " button. The machine starts the

automatic priming of the circuit and the bar under the icon shows the

operation progress.

When the process is complete, the machine stops dispensing automa-

tically.

The display might show the machine warm-up icon, as shown in the

 gure.

YellowGreen

3

Once the warm-up is complete, the machine performs a rinse cycle of

the internal circuits.

During this phase, the icon indicated in the  gure will be displayed.

4

When the operations described above are complete, the icon is displa-

yed.

The machine is ready to brew beverages.

5

To brew co ee or dispense hot water or steam, and for a proper use of

the machine, carefully follow the instructions provided.

Note: If the machine is being used for the  rst time or after a long period of

inactivity, follow the procedures described in the following section.

2

Place a container under the dispensing spout.

10

ENGLISH

Rinse/Self-Cleaning Cycle

After the automatic priming of the circuit, the machine will automatically

rinse/clean the circuit. This cycle allows you to rinse the internal co ee

circuits with fresh water. The cycle is automatically performed also in the

following conditions:

• At machine start-up (with cold boiler)

• After priming the circuit (with cold boiler)

• During the Stand-by preparation phase (if a co ee product has been

brewed)

• During the turning o phase after pressing the ON/OFF button (if a

co ee product has been brewed).

A small amount of water will be dispensed to rinse and heat all the ma-

chine parts; in this phase this icon is displayed.

We strongly recommend to wait for the cycle to  nish automatically.

You can stop dispensing by pressing the “

” button.

For a perfect Espresso: Rinse the co ee circuit if using the machine

for the  rst time or after a long period of inactivity.

Besides the rinse/self-cleaning cycle, we recommend you to run these

simple operations to always brew excellent espresso.

They have to be performed:

A) At  rst start-up;

B) When the machine remains inactive for a long time (more than 2

weeks).

1

Place a large container under the dispensing spout.

Yellow

Before starting the procedure, check that the following icon is dis-

played.

GreenGreen

2

Select the pre-ground co ee brewing function by pressing the " "

button one or more times, until the following icon is displayed.

Note: Do not add pre-ground co ee into the compartment.

ENGLISH

11

Green

7

Press the " " button to start dispensing hot water. Dispense water

until the no water signal appears.

8

At the end,  ll the water tank again. Then the products can be brewed

as described in the following sections.

Note: If available, it is necessary to install a new "Intenza +"  lter in the ma-

chine as described in the following section.

3

Press the " " button. Wait until the dispensing procedure is complete

and empty the water tank.

4

Repeat the operations from step 1 to step 3 for 3 times, then continue

with step 5.

5

Place a container under the water dispensing spout.

6

Press the " " button.

The following icon is displayed.

12

ENGLISH

Measuring Water Hardness

Measuring water hardness is very important in order to correctly manage

the “INTENZA+”  lter and the frequency with which the machine must be

descaled.

1

Immerse the water hardness test strip - provided with the machine - in

water for 1 second.

Note: The test strip is only valid for one measurement.

2

Check how many squares change colour and refer to the table.

Note: The letters correspond to the references that are located in the base of the

“INTENZA+”  lter. The  lter must be adjusted according to this measurement.

3

The numbers correspond to the settings that are found for the water

hardness adjustment, shown in the programming chapter.

More precisely:

1 = 1 (very soft water)

2 = 2 (soft water)

3 = 3 (hard water)

4 = 4 (very hard water)

YellowYellowGreen

4

Once you know this value, set the water hardness value.

Press the “

” button and scroll the pages by pressing the “ ” but-

ton until the following page is displayed.

Note: The machine is supplied with a standard adjustment suitable for most of

the uses.

5

Press:

The “

” button to increase the value

or

the “

” button to reduce the value.

6

Press the “ ” button to con rm the adjustment.

7

Press the “ ” button to exit and brew the products.

23 4

A

B

C

Intenza Aroma System

Machine water hardness setting

1

ENGLISH

13

"INTENZA+" Water Filter (Optional)

The "INTENZA+" water  lter can improve the quality of water. Using the

"INTENZA+"  lter will prevent limescale from building up and will ensure a

much more intense aroma to your espresso co ee. We therefore recom-

mend you install the "INTENZA+" water  lter, which can be purchased

from your local dealer or on-line at the Philips on-line store http://shop.

philips.com or at authorized service centres.

"INTENZA+" Water Filter Installation

1

Remove the small white  lter from the tank and store it in a dry place

sheltered from dust.

2

Remove the "INTENZA+" water  lter from its package, immerse it

vertically (with the opening positioned upwards) in cold water and

delicately press the sides so as to let the air bubbles out.

Measuring water hardness is very important in order to correctly manage

the "INTENZA+" water  lter and the frequency with which the machine

must be descaled.

3

The  lter should be set according to the measurements performed to

set the water hardness. Use the water hardness test strip provided with

the machine. Set the "Intenza Aroma System" as speci ed on the  lter

package (see section "Measuring Water Hardness").

A = Soft water

B = Hard water (standard)

C = Very hard water

4

Put the  lter into the empty tank. Press it until its limit stop.

5

Fill the tank with fresh drinking water and reinsert it into the machine.

14

ENGLISH

YellowYellow YellowYellowGreen

6

Dispense the water in the tank by using the hot water function (see

section "Hot Water Dispensing”).

7

Fill the water tank again.

8

Press the " " button and scroll the pages by pressing the " " but-

ton until the following page is displayed.

Note: When the “INTENZA +” water  lter needs to be replaced with a new one,

the following icon is displayed; in this case the function must be reset. Replace

the  lter as previously shown.

9

Press the " " button to select "ON" and press the " " button to

con rm.

In this way the machine has been programmed to inform the user of

the need to replace the  lter.

Yellow

After that, enter the programming menu until the indicated page is displayed

and select the "RESET" option. Then press the "

" button. The machine is now

programmed to manage a new  lter.

Note: If the  lter is already installed and you want to remove - but not replace -

it, select the "OFF" option and then press the "

" button.

10

To exit, press the " " button until the home page is displayed.

Note: If there is no "INTENZA+" water  lter, insert the small white  lter previ-

ously removed into the water tank.

ENGLISH

15

Espresso Co ee: Brewing and Adjustments

The machine you have bought works with co ee beans and/or pre-ground

co ee. It allows for certain adjustments that will permit you to use it to its

full potential and get a complete "Espresso experience".

Saeco Adapting System: An intelligent self-adjusting system that allows the

use of all types of co ee beans available on the market.

Co ee is a natural product and its characteristics may change according

to its origin, blend and roast. The Saeco co ee machine is equipped with a

self-adjusting system that allows the use of all types of co ee beans avail-

able on the market (non caramelised).

• The machine automatically adjusts itself in order to optimise the

extraction of the co ee, ensuring perfect compression of the tablet to

obtain a creamy espresso co ee that will release all the aromas, regard-

less of the type of co ee used.

• The optimisation process is a learning process that requires the brew-

ing of a certain number of co ee cups to allow the machine to adjust

the compactness of the ground co ee.

• Attention should be given to special blends, which require grinder ad-

justments in order to optimise the extraction of co ee - (see “Adjusting

the Co ee Grinder” section”).

Pre-brewing Technology: Enhancing the Aroma

Thanks to the Pre-brewing Technology, ground co ee is moistened before

the actual brewing process, ensuring that the aroma can unfold even bet-

ter.

Adjustable Ceramic Co ee Grinder: A Full Aroma Preservation

The ceramic grinders always guarantee accurate grinding for every co ee

blend. In addition, this technology prevents the beans from overheating.

These two combined factors provide for a full aroma preservation, deliver-

ing the truly Italian taste in every cup.

Warning! The grinder adjustment knob, which is placed inside the cof-

fee bean hopper, must be turned with the Co ee grinder adjustment

key only when the co ee grinder is working. Do not put any material

other than co ee beans into the hopper. Do not pour ground and/or

instant co ee into the co ee bean hopper.

Warning: The co ee grinder contains moving parts that may be dangerous.

Therefore, do not insert  ngers and/or other objects. In case of malfunc-

tion, turn o the appliance by pressing the ON/OFF button and remove the

plug from the socket before carrying out any type of operation inside the

co ee bean hopper. Do not pour co ee beans when the co ee grinder is

working.

The machine allows you to make slight adjustments to the co ee grinder

to adapt it to the kind of co ee used.

The adjustment must be performed by means of the pin located inside the

16

ENGLISH

co ee bean hopper. This must be pressed and turned using the supplied

key only.

Press and turn the pin one notch at a time and brew 2-3 cups of co ee; this

is the only way to notice di erences in grind.

1

2

The reference marks inside the co ee bean hopper indicate the grind set-

ting. There are 5 di erent grind settings to choose from with the following

references:

1 - Coarse Grind: Lighter taste, for dark roasted co ee blends;

2 - Fine Grind: Bolder Taste, for light roasted co ee blends.

"Aroma" Adjustment: Select Your Favourite Amount

Choose your favourite co ee blend and adjust the amount of co ee to be

ground until they meet your personal taste. The machine is set-up to adjust

the amount according to the co ee to be ground.

Four choices are possible by pressing and releasing the "

" button: Mild,

medium or strong aroma, and pre-ground co ee.

Selection can be made when the beans appear on the display.

Each time the "

" button is pressed and released, the aroma changes by

one degree, according to the selected amount:

= Mild aroma

= Medium aroma

= Strong aroma

Note: Selection must be made prior to select co ee. The system sets the aroma

according to the personal taste of the user.

After selecting "Strong aroma", the function for brewing co ee with pre-

ground co ee is displayed.

This selection is displayed by the icon on the side.

Refer to the relevant section to use this function.

GreenGreen

ENGLISH

17

Brewing Co ee

Before brewing co ee:

- Check the warnings on the display and make sure that the water tank

and co ee bean hopper are full.

- Adjust the height of the dispensing spout according to your needs and

select the aroma or the pre-ground co ee.

Adjusting the Dispensing Spout

Most cups on the market can be used with this co ee machine.

The height of the dispensing spout may be adjusted to better  t the

dimensions of the cups that you wish to use.

Manually move the dispensing spout up or down to adjust its height by

placing your  ngers as shown in the  gure.

The recommended positions are:

For the use of small cups;

For the use of large cups.

Two cups can be placed under the dispensing spout to brew two cups of co ee

at the same time.

18

ENGLISH

Using Co ee Beans

To brew a cup of Espresso co ee, press and release:

1

The " " button to select the desired Aroma;

2

The " " button for a cup of espresso;

or

the "

" button for a cup of long espresso.

The brewing cycle will start:

To brew 1 cup of co ee, press the button once. This icon will be dis-

played.

To brew 2 cups of co ee, press the button twice consecutively. This

icon will be displayed.

Note: To brew 2 cups of co ee, the machine automatically grinds and doses the

correct amount of co ee. Brewing two co ees requires two grinding cycles and

two brewing cycles, which the machine carries out automatically.

3

Once the prebrewing cycle is complete, co ee begins to come out of

the dispensing spout.

4

The co ee brewing process stops automatically. It is nevertheless

possible to interrupt the co ee brewing process by pressing the “

”

"STOP" button.

Using Pre-ground Co ee

This function allows using pre-ground and deca einated co ee.

Pre-ground co ee must be poured into the relevant compartment posi-

tioned next to the co ee bean hopper. Only use ground co ee for espresso

machines and never co ee beans or instant co ee.

Note:

With this function you can just brew one cup of co ee at a time.

If no pre-ground co ee is poured into the compartment, only water will be

dispensed.

If the dose is excessive and 2 or more measuring scoops of co ee are used, the

machine will not brew the product. Also in this case, the machine will run an

empty cycle and discharge any ground co ee into the co ee grounds drawer.

To brew co ee:

1

Press and release the " " button one or more times to select and

activate the pre-ground co ee function.

2

Lift the pre-ground co ee compartment lid.

Add only 1 scoop of pre-ground co ee to the compartment. Use only

the measuring scoop supplied with the machine to perform this opera-

tion. Then, close the lid.

GreenGreenGreen

Page is loading ...

Saeco HD8753/15 Operating instructions

This manual is also suitable for

Saeco HD8753/15 Operating instructions

Related papers

Other documents