Spektrum AR636 6-Channel AS3X Sport Receiver Owner's manual

Category
Toy parts
Type
Owner's manual
Instruction Manual
Bedienungsanleitung
Manuel d’utilisation
Manuale di Istruzioni
2
EN
• Setalltransmittersettingsto
default.
Important: The Aileron, Elevator
and Rudder settings in the
transmitter must remain at their
factory default values. Settings for
reverse, sub trim, travel adjustment,
expo and dual rate must be done in
the App only.
1.Installthereceiverinoneof8
possibleorientationsusingdouble
sidedtape.
2.Theservoportsmustbefacingthe
frontorrearoftheaircraft.
3.Thereceivermustbemounted
paralleltotheroll,pitchandyaw
axis(NOTANGLED).
1.Insertthebindplugintointhe
receiverbindportandpoweron
thereceiver.TheLEDshouldblink
toindicatethereceiverisinbind
mode.
2.Bindthetransmittertothereceiver
atlowthrottle.Refertoyour
transmitter’smanualfordetails
onhowtobindtoyourspecic
transmitter.
Togetmoreinformation,includingdetailsondownloading
theSpektrum™AS3X
®
MobileProgrammingApplication,
visitwww.SpektrumRC.com/AS3XorscanthisQRcode.
Transmitter Setup Connecting to the Receiver
Plug servo leads into assigned ports
Installing the Receiver
Binding
Getting Started
CLEAR
BACK
®
AR636 shown
AR636 shown
1.Connecttheservoplugonthe
audiointerfacecabletotheBIND/
PROGportonyourreceiver.
2.Powerthereceiverthroughany
openchannel.
3.Connecttheaudioplugonthe
interfacecabletotheaudiojack
onyourmobiledevice.Thevolume
MUSTbeturneduptofull.
4.Ensureyouhavesecurereceiver
dataportandaudiodataport
connections.
Ifthereceiverisbeingconnected
forthersttime,theAppwill
automaticallyopeninModelWizard
intheModelSetupscreen.
*Minimum system requirements:
iOS 6.0, iPhone 4, iPod 4th gen and Android 4.0
*Does not apply to iOS Devices.
If your Android device does not recognize the receiver*
1.Ensureyouhavesecurereceiverdata
portandaudiodataportconnections.
2.Disconnecttheaudioplugfromthe
device.
3.Separatetheservoplugsinthemiddle
oftheinterfacecable.
4.Flipthedeviceservoplug180degrees
andre-connecttheservoplugs.
5.Re-connecttheaudioplugtothe
device.
Normal Model Type
• Port1:Throttle
• Port2:Aileron
• Port3:Elevator
• Port4:Rudder
• Port5:Gear/Flap
• Port6:Left
Aileron
(ifequippedwith
dualservos)
Delta /
Elevon Model Type
• Port1:Throttle
• Port2:Right
Aileron
• Port3:Left
Aileron
• Port4:Rudder
• Port5:Gear
• Port6:Aux1
Typical Servo Port Assignments*:
Port1
Bind/Prog
Port2
Port3
Port4
Port5
Port6
*AR636 shown for reference. Port assignments
will be similar for all AS3X receivers. Refer to your
receivers manual for more information.
3
EN
Navigation
1. and movetothenextorpreviousscreenintheWizard.
2.The appearsattheendoftheWizard.TapthesquaretosavetheairplanecongurationandtoexittheWizard.
The Wizard
TheWizardstartsautomaticallywhenyouopentheappforthersttime.
1.Selectaphotoforthemodel(optional).
2.NametheModel.
3.Selectthereceiverthatyouwanttoprogram.Ifareceiverisalreadybound
andconnectedtothemobiledevice,theappwillauto-detectthereceiver.
4.Selectyourtransmitter.
Model Setup
4
EN
Telltheapphowthereceiverismountedinyouraircraft.
1.Toipthereceiverhorizontally,swipeLEFTorRIGHT.
2.Toipthereceiververtically,swipeUPorDOWN.
Theservopinsmustalwayspointtowardthenoseortailoftheaircraft.
Receiver orientation
Selectthetransmitterchannelyouwanttouseforightmodes.
Flight Mode Setup
1.Swipeleftorrightacrossthewingtochangethewingtype.
2.Swipeleftorrightacrossthetailtochangethetailtype.Ifatailtypeisnot
available,itisbecauseyouhaverunoutofchannelsinthereceiver.
Wing Type
5
EN
Theportassignmentscreenshowsyouwheretoconnecttheservostothe
receiver.Nooptionsareavailableonthisscreen;itisonlyusedforreference.
Port Assignment
YouhavetheoptionofselectingPresetorHoldforeachreceiverport.Ifyou
aren’tsurewhateachportdoes,tapthe toreturntothePortAssignment
screen.
Failsafe
Tap each surface to access the following:
Ifthesurfacemovesinthewrongdirectionwhenyoumovethecontrol
stickonthetransmitter,taptheselectortoreversethedirection.
Servo Reverse
Surface Setup
• ServoReverse
• SubTrim
• Travel
• Balance
6
EN
1. TapSUBTRIMtoaccessthesubtrimvalue.
2.Tapthe-or+tochangethesubtrimvalue.Tapping-movesthetrimto
theLeftand+movesthetrimtotheRight.
3.TapSUBTRIMagaintosavethevalue.
1. TapTRAVELtoaccessthetraveladjustgraph.
2.Toadjustthetravelvaluesdragupordownontheverticallinetoadjust
theLeft/Rightvaluessimultaneously.
•Directionscanbeadjustedatthesametimeorindependently.Toadjust
directionsatthesametime,makesurebothdirectionsareorange.
Active: Directionisorange
 Inactive: Directionisgray
Sub Trim
Travel
Thebalancefunctionisa7-pointcurveusedtopreventbindingwhenmultiple
servosareusedonasinglecontrolsurface.Toadjustthebalanceonacontrol
surface,drageachofthe7pointsonthecurveuntilthecontrolsurfacemoves
withoutbinding.
Press toreturntotheWizard.
Balance
7
EN
AS3X Settings
TheInitialSetupmenuenablesyoutoviewindividualscreenswithoutusing
theWizard.YouwillalsousetheInitialSetupmenutoperformaModelReset,
sharemodellesviae-mailoraccesstheWizard.SomescreensintheInitial
Setupmenualsohaveprogrammingcapabilitiesthatarenotavailableinthe
Wizard.
Initial Setup
SelectthetransmitterchannelyouwishtousefortheFlightModeswitch.
Tip: IfyouwishtousetheGearchannelforightmodes,butalsowish
tousea3-positionswitch,youwillneedtoassigntheGearchanneltoa
3-positionswitchinthetransmitter.
ThePortAssignmentscreenenablesyoutochangethereceiverport
assignmentforeachsurface.
CAUTION: Changingtheportassignmentsmaycauseissueswith
othercontrolsurfacesormixesthatyouhaveprogrammedinyour
transmitter.Alwaysperformacontroltestandsetfailsafevaluesbefore
yingyouraircraft.Failuretodosomayresultintheaircraftcrashing.
• Gray port assignemnts are not in use.
• Orange port assignments are currently in use.
• Red port assignments are currently being used as part of a
mix.
IMPORTANT: IfyouselectAircraftTypeintheInitialSetupmenu,the
followingpop-upalertappears:
“Reselecting your aircraft type will reset all your surface settings. Are
you sure you want to continue.”
Ifyouselect“Continue”,youmustre-programallofyourtravelvalues,dualrates,
etc.
Flight Mode Switch
Port Assignment
Wing Type
SurfaceSetupisthelaststepintheWizard.Pressthe intheupperright
cornertosavesettingsandexittheWizard.Theapplicationwilldisplaythe
AS3XSettingsmenuafterexitingtheWizard.
Exit the Wizard
8
EN
Resetstheactivemodelintheapplication.
Attachestheactivemodelletoanewemail.Theemailrecipientcanopen
theattachmentintheAS3XProgrammerapp.
Model Reset
Share Via Email
• PositiveExpodecreasescontrolsticksensitivitynearcenter.
• NegativeExpoincreasescontrolsticksensitivitynearcenter.
1. SwipeleftorrighttochangebetweenRoll,
PitchandYaw.
2.SelectaightmodetoaccesstheExpocurve.
3.DragthecurveUPorDOWNtoadjusttheExpovalues.
• Directionscanbeadjustedatthesametimeorindependently.Toadjust
directionsatthesametime,makesurebothdirectionsareorange.
Active: Directionisorange
 Inactive: Directionisgray
4.Pressthe toreturntothemainExposcreen.
Expo
DualRateisapercentageoftheTravelvalue.
1. SwipeleftorrighttochangebetweenRoll,
PitchandYaw.
2.SelectaightmodetoaccesstheDualRatecurve.
3.DragthecurveUPorDOWNtoadjusttheDualRatevalues.
• Directionscanbeadjustedatthesametimeorindependently.Toadjust
directionsatthesametime,makesurebothdirectionsareorange.
Active: Directionisorange
 Inactive: Directionisgray
4.Pressthe toreturntothemainDualRatescreen.
Dual Rate
9
EN
GainisapercentageoftheTravelvalue.
1. SwipeleftorrighttochangebetweenRoll,PitchandYaw
2.SelectaightmodetoaccesstheGaincurve.
3.DragthecurvetoadjusttheGainvalues.
• Directionscanbeadjustedatthesametimeorindependently.Toadjust
directionsatthesametime,makesurebothdirectionsareorange.
Active: Directionisorange
 Inactive: Directionisgray
Gain & Priority
WhenABSisselected,theRateandHeadingGainvaluesthatare
programmedintheApplicationarexed(absolute)foreachgivenight
modeandarenotadjustablefromthetransmitter.
WhenRELisselected,theRateandHeadinggainvaluesareadjustable
fromthetransmitter.Thisallowsinightgainadjustments.SomeSpektrum
transmittersfeatureanAS3Xscreenthatallowsthegaintobeadjusted
fromthetransmitteranddisplaystheactivevalueforeachgainthat
includespriorityinrealtime.
IMPORTANT: WhenRELisselected,thegainvalueintheapplication
representsthemaximumavailablegain.
ABS- Absolute
REL- Relative
1.DragupordownintheblackareaofthecurvetoadjusttheRateGain.
2.DragupordownontheverticallinetoadjusttheHeadingGain.Heading
Gainisonlyactivewhenthetransmittercontrolstickisnearcenter.
3.DragleftorrightacrosstheverticallinetoadjusttheStickPriority.
AdjustingthePriorityenablesyoutoturnthegainoffwhenthe
transmittercontrolstickreachesacertainposition.
4 Pressthe toreturntotheGainscreen.
TheMixingmenuintheAS3XProgrammerAppisonlyusedformixes
involvingcontrolsurfaces.Anymixesinvolvinglights,retracts,etc.should
beprogrammedinyourtransmitterasusual.Sixprogrammablemixesare
availableintheapp.
1. Pressthe“+”tocreateanewmix.
2.Assignthemasterandslavechannels.
3.Assignmixvalues.
4.Pressthesyncbuttontosavethemixandsendtheprogrammingtothe
receiver.Youmustsendthemixprogrammingtothereceiverbeforeyoucan
createanothermix.
Mixing
10
EN
TheDashboardscreenenablesyoutoseeallofthegain,dualrateandexposettingsforeachFlightMode.Youcanalsoadjustthevaluesbyselectinganyofthe
valueboxes.
Dashboard
Contact Information
CountryofPurchase HorizonHobby ContactInformation Address
United States of America
Horizon Service Center
(Repairs and Repair Requests)
servicecenter.horizonhobby.com/Request-
Form/
4105 Fieldstone Rd
Champaign, Illinois, 61822 USA
Horizon Product Support
(Product Technical Assistance)
www.quickbase.com/db/
bghj7ey8c?a=GenNewRecord
Heli 888-959-2304
Air 888-959-2305
Sales
sales@horizonhobby.com
Heli 888-959-2304
Air 888-959-2305
United Kingdom
Service/Parts/Sales:
Horizon Hobby Limited
sales@horizonhobby.co.uk
Units 1–4 , Ployters Rd, Staple Tye
Harlow, Essex, CM18 7NS, United Kingdom
+44 (0) 1279 641 097
Germany
Horizon Technischer Service service@horizonhobby.de
Christian-Junge-Straße 1
25337 Elmshorn, Germany
Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100
France
Service/Parts/Sales:
Horizon Hobby SAS
infofrance@horizonhobby.com
11 Rue Georges Charpak
77127 Lieusaint, France
+33 (0) 1 60 18 34 90
China
Service/Parts/Sales:
Horizon Hobby – China
info@horizonhobby.com.cn
Room 506, No. 97 Changshou Rd.
Shanghai, China 200060
+86 (021) 5180 9868
©2014HorizonHobby,LLC.DSM,DSM2,DSMX,theDSMXlogo,AS3X,andtheHorizonHobbylogoareregisteredtrademarksofHorizonHobbyLLC.The
SpektrumtrademarkisusedwithpermissionofBachmannIndustries,Inc.Apple
®
isatrademarkofAppleInc.,registeredintheU.S.andothercountries.Android
andGooglearetrademarksorregisteredtrademarksofGoogleInc.Allothertrademarks,servicemarksandlogosarepropertyoftheirrespectiveowners.
Created07/2014•42221
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Spektrum AR636 6-Channel AS3X Sport Receiver Owner's manual

Category
Toy parts
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI