Ibiza Light HYPNO40-LED Owner's manual

Brand: Ibiza Light

Model: HYPNO40-LED

Category: Stroboscopes & disco lights

Type: Owner's manual

Ibiza Light & Sound HYPNO40-LED is an impressive light effect featuring 4x 10W RGBW CREE LEDs that generate mesmerizing psychedelic projections on walls, ceilings, and floors. With 8 DMX channels, it offers hypnotic effects, multiple operating modes, and remote control convenience. Ideal for creating dynamic light shows for parties, events, or stage performances.

©Copyright LOTRONIC 2017 HYPNO40-LED Page 1

Ref.: HYPNO40-LED (16-2070)

USER

MANUAL

MANUEL D’UTILISATION

BEDIENUNGSANLEITUNG

HANDLEIDING

Imported from China by

LOTRONIC SA – Avenue Zénobe Gramme 9 – 1480 Saintes - Belgium

©Copyright LOTRONIC 2017 HYPNO40-LED Page 2

BEFORE YOU BEGIN

Contents of the carton:

• 1 x light effect

• 1 x mains lead

• 1 x remote control

• 1 x user manual

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are

present and have been received in good condition. Notify the freight company immediately and retain packing

material for inspection if any parts appear to be damaged from shipping or the carton itself shows signs of

mishandling. Keep the carton and all packing materials. In the event that a fixture must be returned to the factory, it

is important that the fixture be returned in the original factory box and packing.

Safety Instructions

Please read these instructions carefully, they include important information about the installation, usage and

maintenance of this product.

• Please keep this User Guide for future reference. If you sell the unit to another user, be sure that they also receive

this instruction booklet.

• Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is

not higher than that stated on the decal or rear panel of the fixture.

• This product is intended for indoor use only!

It is essential that the device is earthed. A qualified person must carry out the electric connection.

• To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable

materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent surfaces. Be

sure that no ventilation slots are blocked.

• Always disconnect from power source before servicing or replacing fuse and be sure to replace with same fuse size

and type.

• Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use its carrying

handles.

• Maximum ambient temperature (Ta) is 104° F (40°C). Do not operate the fixture at temperatures higher than this.

• In the event of a serious operating problem, stop using the unit immediately. Never try to repair the unit by

yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest

authorized technical assistance center. Always use the same type of spare parts.

• Don’t connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

DISCONNECT DEVICE: Where the MAINS plug or an appliance coupler is used as the disconnect device, the

disconnect device shall remain readily operable.

Features

DMX controlled light effect fitted with 4 CREE LEDs that project psychedelic effects on walls, ceiling and floor.

• 8 DMX channels

• 4x 10W RGBW CREE led’s

• Hypnotic effects

©Copyright LOTRONIC 2017 HYPNO40-LED Page 3

• Operating modes: Auto, sound, DMX, Master-slave & remote controlled

• Remote control

Power supply .................................................................................................. 110-240Vac 50/60Hz

Consumption ................................................................................................................... 50W max.

Fuse ............................................................................................................. F3AL 250V Ø5 x 20mm

DMX channels ................................................................................................................ 8 channels

Light source ................................................................................... 4 x 10W RGBW CREE LED 4-in-1

Beam angle ................................................................................................................................... 4°

Dimensions ....................................................................................................... 155 x 110 x 150mm

Weight ..................................................................................................................................... 1.5kg

Fixture Linking

You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run

synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of

channels required by all fixtures on a serial data link determines the number of fixtures that the data link can

support.

Important: Fixtures on a serial/data link must be daisy chained in one single line. Maximum recommended serial

data link distance: 100 meters (1640 ft.) Maximum recommended number of fixtures on a serial data link: 32 fixtures

CABLE CONNECTORS

Cabling must have a male XLR connector on one end and a female XLR connector on the other end.

DMX connector configuration

Termination reduces signal errors. To avoid signal transmission problems and interference, it is always advisable to

connect a DMX signal terminator.

CAUTION

Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can cause a

ground loop, and your fixture may perform erratically. Test cables with an ohm meter to check correct polarity and

to make sure the pins are not grounded or shorted to the shield or each other.

Setting up a DMX Serial Data Link

1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the controller.

2. Connect the end of the cable coming from the controller which will have a (female) 3 pin connector to the input

connector of the next fixture consisting of a (male) 3 pin connector.

3. Then, proceed to connect from the output as stated above to the input of the following fixture and so on.

DMX address setting

Each fixture must have a specific starting address. When receiving signal transmission, every fixture will receive

channels control signals for its own starting address.

The user can set several fixtures to the same address or set up a separate address for every device.

If more than one fixture is set to the same address, all of them receive the same DMX channels signals. All connected

fixtures are jointly controlled; the controller can't control a device separately.

If every device is set to a different address, it will receive different DMX signals corresponding to its starting address.

This device has 8 channels, so the first device starting address is set 1, second is 9 (1+8), third is 17 (9+8) and so on.

INPUT

COMMON

DMX +

DMX-

Resistance 120 ohm

1/ 4w between pin 2

(DMX-) and pin 3

(DMX+) of the last

fixture.

©Copyright LOTRONIC 2017 HYPNO40-LED Page 4

MENU operation

This fixture has 4 buttons on the rear panel to access, edit and set all functions.

[MENU]: press MENU key to enter into the submenus. Press MENU again to leave the sub-menu. If no key is pressed

during 30 seconds, the unit will go back to MENU display automatically.

[Up]: press UP key to increase the displayed values. Keep pressed to increase the values quickly.

[Down]：press DOWN key to decrease the displayed values. Keep pressed to decrease the values quickly.

[ENTER]：in normal status, this button has no function. In edit mode, press ENTER to enter into the sub-menu.

MODE MENU FUNCTION

A001~A511

A001~A511 DMX Mode/Strobe

A1 *

A1 1 R

A1 2 G

A1 3 B

A1 4 W

A1 5 RGBW

A1 6 RG

A1 7 BW

A1 8 GB

A1 9 RW

A110 RB

A111 GW

A112 GBW

A113 RBW

A114 RGW

A115 RGB