Philips 190CW7CB User manual

e-Manual

Philips LCD Monitor Electronic User’s Manual

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20...190CW7CS.00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/INDEX.HTM2006-12-4 15:15:50

Safety and Troubleshooting Information

• Safety Precautions and

Maintenance

• FAQs

• Troubleshooting

• Regulatory Information

• Other Related Information

Safety and Troubleshooting Information

Safety precautions and maintenance

WARNING: Use of controls, adjustments or procedures other than

those specified in this documentation may result in exposure to shock,

electrical hazards and/or mechanical hazards.

Read and follow these instructions when connecting and using your computer monitor:

Operation:

● Keep the monitor out of direct sunlight and away from stoves or any other heat source.

● Remove any object that could fall into ventilation holes or prevent proper cooling of the

monitor’s electronics.

● Do not block the ventilation holes on the cabinet.

● When positioning the monitor, make sure the power plug and outlet are easily accessible.

● If turning off the monitor by detaching the power cable or DC power cord, wait for 6

seconds before attaching the power cable or DC power cord for normal operation.

● Please use approved power cord provided by Philips all the time. If your power cord is

missing, please contact with your local service center. (Please refer to Customer Care

Consumer Information Center)

● Do not subject the LCD monitor to severe vibration or high impact conditions during

operation.

● Do not knock or drop the monitor during operation or transportation.

Maintenance:

● To protect your display from possible damage, do not put excessive pressure on the LCD

panel. When moving your monitor, grasp the frame to lift; do not lift the monitor by

placing your hand or fingers on the LCD panel.

● Unplug the monitor if you are not going to use it for an extensive period of time.

● Unplug the monitor if you need to clean it with a slightly damp cloth. The screen may be

wiped with a dry cloth when the power is off. However, never use organic solvent, such

as, alcohol, or ammonia-based liquids to clean your monitor.

● To avoid the risk of shock or permanent damage to the set, do not expose the monitor to

dust, rain, water, or excessive moisture environment.

● If your monitor gets wet, wipe it with dry cloth as soon as possible.

● If foreign substance or water gets in your monitor, please turn the power off immediately

and disconnect the power cord. Then, remove the foreign substance or water, and send

it to the maintenance center.

● Do not store or use the LCD monitor in locations exposed to heat, direct sunlight or

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20....00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/safety.htm (1 of 2)2006-12-4 15:16:03

Safety and Troubleshooting Information

extreme cold.

● In order to maintain the best performance of your monitor and use it for a longer lifetime,

please use the monitor in a location that falls within the following temperature and

humidity ranges.

❍ Temperature: 0-40°C 41-95°F

❍ Humidity: 20-80% RH

Service:

● The casing cover should be opened only by qualified service personnel.

● If there is any need for any document for repair or integration, please contact with your

local service center. (please refer to the chapter of "Consumer Information Center")

● For transportation information, please refer to "Physical Specifications".

● Do not leave your monitor in a car/trunk under direct sun light.

Consult a service technician if the monitor does not operate normally, or you are

not sure what procedure to take when the operating instructions given in this

manual have been followed.

RETURN TO TOP OF THE PAGE

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20....00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/safety.htm (2 of 2)2006-12-4 15:16:03

FAQs (Frequently Asked Questions)
  
             
 
 
•  Safety and Troubleshooting
 
•  General FAQs
 
•  Screen Adjustments
 
•  Compatibility with Other 
Peripherals
 
•  LCD Panel Technology
 
•  Ergonomics, Ecology and 
Safety Standards
 
•  Troubleshooting
 
•  Regulatory Information
 
•  Other Related Information
 
 
 
FAQs (Frequently Asked Questions)
General FAQs 
Q:
 When I install my monitor what should I do if the screen shows 'Cannot display this video 
mode'?
A: Recommended video mode for Philips 19 ": 1440 x 900 @60Hz.
1.  Unplug all cables, then connect your PC to the monitor that you used 
previously.
2.  In the Windows Start Menu, select Settings/Control Panel. In the Control Panel 
Window, select the Display icon. Inside the Display Control Panel, select the 
'Settings' tab. Under the setting tab, in box labeled 'desktop area', move the 
slidebar to 1440 x 900 pixels (19").
3.  Open 'Advanced Properties' and set the Refresh Rate to 60Hz, then click OK.
4.  Restart your computer and repeat step 2 and 3 to verify that your PC is set at 
1440 x 900@60Hz (19").
5.  Shut down your computer, disconnect your old monitor and reconnect your 
Philips LCD monitor.
6.  Turn on your monitor and then turn on your PC.
Q: What does 'refresh rate' mean in connection with an LCD monitor?
A: The refresh rate is of much less relevance for LCD monitors. LCD monitors display 
a stable, flicker-free image at 60Hz. There is no visible difference between 85Hz and 
60Hz.
Q: What are the .inf and .icm files on the CD-ROM? How do I install the drivers (.inf and .
icm)?
A: These are the driver files for your monitor. Follow the instructions in your user 
manual to install the drivers. Your computer may ask you for monitor drivers (.inf and .
icm files) or a driver disk when you first install your monitor. Follow the instructions to 
insert the ( companion CD-ROM) included in this package. Monitor drivers (.inf and .
icm files) will be installed automatically.
file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20...00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/saf_faq.htm (1 of 8)2006-12-4 15:16:11

FAQs (Frequently Asked Questions)

Q: How do I adjust the resolution?

A: Your video card/graphic driver and monitor together determine the available

resolutions. You can select the desired resolution under Windows® Control Panel

with the "Display properties"

.

Q: What if I get lost when I am making monitor adjustments?

A: Simply press the MENU button, then select 'Reset' to recall all of the original

factory settings.

Q: What is the Auto function?

A: The AUTO adjustment key restores the optimal screen position, phase and clock

settings by pressing of a single button – without the need to navigate through OSD

(On Screen Display) menus and control keys.

Note: Auto function is available in selected models only.

Q: My Monitor has no power (Power LED does not light up). What should I do?

A: Make sure the AC power cord is connected between the monitor and AC outlet,

and click a key on keyboard/mouse to wake up the PC.

Q: Will the LCD monitor accept an interlaced signal under PC models?

A: No. If an Interlace signal is used, the screen displays both odd and even horizontal

scanning lines at the same time, thus distorting the picture.

Q: What does the Refresh Rate mean for LCD?

A: Unlike CRT display technology, in which the speed of the electron beam is swept

from the top to the bottom of the screen determines flicker, an active matrix display

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20...00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/saf_faq.htm (2 of 8)2006-12-4 15:16:11

FAQs (Frequently Asked Questions)

uses an active element (TFT) to control each individual pixel and the refresh rate is

therefore not really applicable to LCD technology.

Q: Will the LCD screen be resistant to scratches?

A: A protective coating is applied to the surface of the LCD, which is durable to a

certain extent (approximately up to the hardness of a 2H pencil). In general, it is

recommended that the panel surface is not subject to any excessive shocks or

scratches.

Q: How should I clean the LCD surface?

A: For normal cleaning, use a clean, soft cloth. For extensive cleaning, please use

isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone,

hexane, etc.

Q:Can I change the color setting of my monitor?

A:Yes, you can change your color setting through OSD control as the following

procedures,

1. Press "MENU" to show the OSD (On Screen Display) menu

2. Press "Left Arrow" to select the option "color" then press "MENU" to enter color

setting, there are five settings as below.

a. 6500K; this setting features the panel closed to red-white color tone.

b. 9300K; this setting features the panel closed to blue-white color tone.

c. Original; this setting load the default panel setting in terms of color

tone. (Note: different panel maker may feature a different color

temperature*)

d. User Define; the user can choose his/her preference color setting by

adjusting red, green, blue color.

e. sRGB; this is a standard setting for ensuring correct exchange of

colors between different device (e.g. digital cameras, monitors, printers,

scanners, etc.)

*A measurement of the color of light radiated by an object while it is being heated. This measurement

is expressed in terms of absolute scale, (degrees Kelvin). Lower Kevin temperatures such as 2004K

are red; higher temperatures such as 9300K are blue. Neutral temperature is white, at 6504K.

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20...00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/saf_faq.htm (3 of 8)2006-12-4 15:16:11

FAQs (Frequently Asked Questions)

Q: Can the Philips LCD Monitor be mounted on the wall?

A: Yes. Philips LCD monitors have this optional feature. For standard VESA mount

holes on the rear cover allows the user to mount the Philips monitor on most of the

VESA standard arms or accessories. We recommend to contact your Philips sales

representative for more information.

RETURN TO TOP OF THE PAGE

Screen Adjustments

Q:

What is the FPadjust program on the CD-ROM?

A: The FPadjust program generates alignment patterns that help you adjust monitor

settings such as Contrast, Brightness, Horizontal Position, Vertical Position, Phase

and Clock for optimal performance.

Q: When I install my monitor, how do I get the best performance from the monitor?

A:

1.

For best performance, make sure your display settings are set at 1440 x

900@60Hz for 19". Note: You can check the current display settings by

pressing the OSD MENU button once. The current display mode is shown in

OSD first page.

2. To install the Flat Panel Adjust (FPadjust) program located on the monitor

setup CD-ROM, open the CD-ROM and double-click the FP_setup4.3.exe

icon. This will install FP Adjust automatically and place a shortcut on your

desktop.

3. Run FPadjust by double clicking the shortcut. Follow the instructions step by

step to optimize image performance with your system's video controller.

Q: How do LCDs compare to CRTs in terms of radiation?

A: Because LCDs do not use an electron gun, they do not generate the same amount

of radiation at the screen surface.

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20...00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/saf_faq.htm (4 of 8)2006-12-4 15:16:11

FAQs (Frequently Asked Questions)

RETURN TO TOP OF THE PAGE

Compatibility with other Peripherals

Q:

Are Philips LCD monitors Plug-and-Play?

A: Yes, the monitors are Plug-and-Play compatible with Windows® 95, 98, 2000, XP,

and Vista.

Q: What is USB (Universal Serial Bus)?

A: Think of USB as a smart plug for PC peripherals. USB automatically determines

resources (like driver software and bus bandwidth) required by peripherals. USB

makes necessary resources available without user intervention. There are three main

benefits of USB. USB eliminates "case anxiety," the fear of removing the computer

case to install circuit board cards -- that often requires adjustment of complicated IRQ

settings -- for add-on peripherals. USB does away with "port gridlock." Without USB,

PCs are normally limited to one printer, two Com port devices (usually a mouse and

modem), one Enhanced Parallel Port add-on (scanner or video camera, for example),

and a joystick. More and more peripherals for multimedia computers come on the

market every day. With USB, up to 127 devices can run simultaneously on one

computer. USB permits "hot plug-in." No need to shut down, plug in, reboot and run

set up to install peripherals. No need to go through the reverse process to unplug a

device. Bottom line: USB transforms today's "Plug-and-Pray" into true Plug-and-Play!

Please refer to glossary for more information about USB.

Q: What is a USB hub ?

A: A USB hub provides additional connections to the Universal Serial Bus. A hub's

upstream port connects a hub to the host, usually a PC. Multiple downstream ports in

a hub allows connection to another hub or device, such as a USB keyboard, camera

or printer.

RETURN TO TOP OF THE PAGE

LCD Panel Technology

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20...00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/saf_faq.htm (5 of 8)2006-12-4 15:16:11

FAQs (Frequently Asked Questions)

Q: What is a Liquid Crystal Display?

A: A Liquid Crystal Display (LCD) is an optical device that is commonly used to

display ASCII characters and images on digital items such as watches, calculators,

portable game consoles, etc. LCD is the technology used for displays in notebooks

and other small computers. Like light-emitting diode and gas-plasma technologies,

LCD allows displays to be much thinner than cathode ray tube (CRT) technology.

LCD consumes much less power than LED and gas-displays because it works on the

principle of blocking light rather than emitting it.

Q:

What differentiates passive matrix LCDs from active matrix LCDs?

A: An LCD is made with either a passive matrix or an active matrix display grid. An

active matrix has a transistor located at each pixel intersection, requiring less current

to control the luminance of a pixel. For this reason, the current in an active matrix

display can be switched on and off more frequently, improving the screen refresh time

(your mouse pointer will appear to move more smoothly across the screen, for

example). The passive matrix LCD has a grid of conductors with pixels located at

each intersection in the grid.

Q: What are the advantages of TFT LCD compared with CRT?

A: In a CRT monitor, a gun shoots electrons and general light by colliding polarized

electrons on fluorescent glass. Therefore, CRT monitors basically operate with an

analog RGB signal. A TFT LCD monitor is a device that displays an input image by

operating a liquid crystal panel. The TFT has a fundamentally different structure than

a CRT: Each cell has an active matrix structure and independent active elements. A

TFT LCD has two glass panels and the space between them is filled with liquid

crystal. When each cell is connected with electrodes and impressed with voltage, the

molecular structure of the liquid crystal is altered and controls the amount of inlet

lighting to display images. A TFT LCD has several advantages over a CRT, since it

can be very thin and no flickering occurs because it does not use the scanning

method.

Q: Why is vertical frequency of 60Hz optimal for an LCD monitor?

A: Unlike a CDT monitor, the TFT LCD panel has a fixed resolution. For example, an

XGA monitor has 1024x3 (R, G, B) x 768 pixels and a higher resolution may not be

available without additional software processing. The panel is designed to optimize

the display for a 65MHz dot clock, one of the standards for XGA displays. Since the

vertical/horizontal frequency for this dot clock is 60Hz/48kHz, the optimum frequency

for this monitor is 60Hz.

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20...00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/saf_faq.htm (6 of 8)2006-12-4 15:16:12

FAQs (Frequently Asked Questions)

Q: What kind of wide-angle technology is available? How does it work?

A: The TFT LCD panel is an element that controls/displays the inlet of a backlight

using the dual-refraction of a liquid crystal. Using the property that the projection of

inlet light refracts toward the major axis of the liquid element, it controls the direction

of inlet light and displays it. Since the refraction ratio of inlet light on liquid crystal

varies with the inlet angle of the light, the viewing angle of a TFT is much narrower

than that of a CDT. Usually, the viewing angle refers to the point where the contrast

ration is 10. Many ways to widen the viewing angle are currently being developed and

the most common approach is to use a wide viewing angle film, which widens the

viewing angle by varying the refraction ratio. IPS (In Plane Switching) or MVA (Multi

Vertical Aligned) is also used to give a wider viewing angle.

Q: Why is there no flicker on an LCD Monitor?

A: Technically speaking, LCDs do flicker, but the cause of the phenomenon is

different from that of a CRT monitor -- and it has no impact of the ease of viewing.

Flickering in an LCD monitor relates to usually undetectable luminance caused by the

difference between positive and negative voltage. On the other hand, CRT flickering

that can irritate the human eye occurs when the on/off action of the fluorescent object

becomes visible. Since the reaction speed of liquid crystal in an LCD panel is much

slower, this troublesome form of flickering is not present in an LCD display.

Q: Why is an LCD monitor virtually low of Electro Magnetic Interference?

A: Unlike a CRT, an LCD monitor does not have key parts that generate Electro

Magnetic Interference, especially magnetic fields. Also, since an LCD display utilizes

relatively low power, its power supply is extremely quiet.

RETURN TO TOP OF THE PAGE

Ergonomics, Ecology and Safety Standards

Q:

What is the CE mark?

A: The CE (Conformité Européenne) mark is required to be displayed on all regulated

products offered for sale on the European market. This 'CE' mark means that a

product complies with the relevant European Directive. A European Directive is a

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20...00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/saf_faq.htm (7 of 8)2006-12-4 15:16:12

FAQs (Frequently Asked Questions)

European 'Law' that relates to health, safety, environment and consumer protection,

much the same as the U.S. National Electrical Code and UL Standards.

Q: Does the LCD monitor conform to general safety standards?

A: Yes. Philips LCD monitors conform to the guidelines of MPR-II and TCO 99/03

standards for the control of radiation, electromagnetic waves, energy reduction,

electrical safety in the work environment and recyclability. The specification page

provides detailed data on safety standards.

More information is provided in the Regulatory Information section.

RETURN TO TOP OF THE PAGE

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20...00/190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/saf_faq.htm (8 of 8)2006-12-4 15:16:12

Troubleshooting

• Safety and

Troubleshooting

• FAQs

• Common Problems

• Imaging Problems

• Regulatory Information

• Other Related Information

Troubleshooting

This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these

solutions, contact Philips customer service representative.

Common Problems

Having this problem Check these items

No Picture

(Power LED not lit)

● Make sure the power cord is plugged into the power outlet

and into the back of the monitor.

● First, ensure that the power button on the front of the monitor

is in the OFF position, then press it to the ON position.

No Picture

(Power LED is amber or yellow)

● Make sure the computer is turned on.

● Make sure the VGA cable is properly connected to your

computer.

● Check to see if the monitor cable has bent pins.

● The Energy Saving feature may be activated

Screen says

● Make sure the monitor cable is properly connected to your

computer. (Also refer to the Quick Set-Up Guide).

● Check to see if the monitor cable has bent pins.

● Make sure the computer is turned on.

AUTO button not working properly

● The Auto Function is designed for use on standard Macintosh

or IBM-compatible PCs running Microsoft Windows.

● It may not work properly if using nonstandard PC or video

card.

Imaging Problems

Display position is incorrect

● Press the Auto button.

● Adjust the image position using the Phase/Clock of More

Settings in OSD Main Controls.

Image vibrates on the screen

● Check that the VGA cable is properly connected to the

graphics board or PC.

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20.../190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/saf_troub.htm (1 of 3)2006-12-4 15:16:13

Troubleshooting

Vertical flicker appears

● Press the Auto button.

● Eliminate the vertical bars using the Phase/Clock of More

Settings in OSD Main Controls.

Horizontal flicker appears

● Press the Auto button.

● Eliminate the vertical bars using the Phase/Clock of More

Settings in OSD Main Controls.

The screen is too bright or too dark

● Adjust the contrast and brightness on On-Screen Display.

(The backlight of the LCD monitor has a fixed life span. When

the screen becomes dark or begins to flicker,

please contact

your sales representative).

An after-image appears

● If an image remains on the screen for an extended period of

time, it may be imprinted in the screen and leave an after-

image. This usually disappears after a few hours

An after-image remains after the power

has been turned off.

● This is characteristic of liquid crystal and is not caused by a

malfunction or deterioration of the liquid crystal. The after-

image will disappear after a peroid of time.

Green, red, blue, dark, and white dots

remains

● The remaining dots are normal characteristic of the liquid

crystal used in today’s technology.

For further assistance, refer to the Consumer Information Centers list and contact Philips customer service

representative.

RETURN TO TOP OF THE PAGE

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20.../190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/saf_troub.htm (2 of 3)2006-12-4 15:16:13

Troubleshooting

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20.../190CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/saf_troub.htm (3 of 3)2006-12-4 15:16:13

Regulatory Information

•

Recycling Information for Customers

•

Waste Electrical and Electronic

Equipment-WEEE

• CE Declaration of Conformity

• Energy Star Declaration

• Federal Communications

Commission (FCC) Notice (U.S.

Only)

•

FCC Declaration of Conformity

• Commission Federale de la

Communication (FCC Declaration)

• EN 55022 Compliance (Czech

Republic Only)

•

MIC Notice (South Korea Only)

• Polish Center for Testing and

Certification Notice

• North Europe (Nordic Countries)

Information

• BSMI Notice (Taiwan Only)

• Ergonomie Hinweis (nur

Deutschland)

• Philips End-of-Life Disposal

• Information for UK only

• China RoHS

• Troubleshooting

• Other Related Information

•

Frequently Asked Questions (FAQs)

Regulatory Information

Model ID: 190CW7

Model No: HWC7190T

Recycling Information for Customers

Philips establishes technically and economically viable objectives to optimize the environmental

performance of the organization's product, service and activities.

From the planning, design and production stages, Philips emphasizes the important of making products

that can easily be recycled. At Philips, end-of-life management primarily entails participation in national

take-back initiatives and recycling programs whenever possible, preferably in cooperation with

competitors.

There is currently a system of recycling up and running in the European countries, such as The

Netherlands, Belgium, Norway, Sweden and Denmark.

In U.S.A., Philips Consumer Electronics North America has contributed funds for the Electronic

Industries Alliance (EIA) Electronics Recycling Project and state recycling initiatives for end-of-life

electronics products from household sources. In addition, the Northeast Recycling Council (NERC) - a

multi-state non-profit organization focused on promoting recycling market development - plans to

implement a recycling program.

In Asia Pacific, Taiwan, the products can be taken back by Environment Protection Administration (EPA)

to follow the IT product recycling management process, detail can be found in web site www.epa.gov.tw

For help and service, please contact Consumers Information Center or F1rst Choice Contact Information

Center in each country or the following team of Environmental specialist can help.

Mr. WY Chen- Environment manager

Philips Multimedia Flat Display

E-mail: [email protected]

Tel: +886 (0) 3 222 6791

Mr. Maarten ten Houten - Senior Environmental Consultant

Philips Consumer Electronics

E-mail: [email protected]

Tel: +31 (0) 40 27 33402

Mr. Delmer F. Teglas

Philips Consumer Electronics North America

E-mail: [email protected]

Tel: +1 865 521 4322

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20...0CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/regs/regulat.htm (1 of 10)2006-12-4 15:16:17

Regulatory Information

RETURN TO TOP OF THE PAGE

Waste Electrical and Electronic Equipment-WEEE

Attention users in European Union private households

This marking on the product or on its packaging illustrates that, under European Directive

2002/96/EG governing used electrical and electronic appliances, this product may not be disposed of

with normal household waste. You are responsible for disposal of this equipment through a designated

waste electrical and electronic equipment collection. To determine the locations for dropping off such

waste electrical and electronic, contact your local government office, the waste disposal organization that

serves your household or the store at which you purchased the product.

RETURN TO TOP OF THE PAGE

CE Declaration of Conformity

Philips Consumer Electronics declare under our responsibility that the product is in conformity with the

following standards

- EN60950-1:2001 (Safety requirement of Information Technology Equipment)

- EN55022:1998 (Radio Disturbance requirement of Information Technology Equipment)

- EN55024:1998 (Immunity requirement of Information Technology Equipment)

- EN61000-3-2:2000 (Limits for Harmonic Current Emission)

- EN61000-3-3:1995 (Limitation of Voltage Fluctuation and Flicker)

following provisions of directives applicable

- 73/23/EEC (Low Voltage Directive)

- 89/336/EEC (EMC Directive)

- 93/68/EEC (Amendment of EMC and Low Voltage Directive)

and is produced by a manufacturing organization on ISO9000 level.

The product also comply with the following standards

- ISO9241-3, ISO9241-7, ISO9241-8 (Ergonomic requirement for CRT Monitor)

- ISO13406-2 (Ergonomic requirement for Flat Panel Display)

- GS EK1-2000 (GS specification)

- prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual Display)

- MPR-II (MPR:1990:8/1990:10 Low Frequency Electric and Magnetic fields)

- TCO'99, TCO'03 (Requirement for Environment Labelling of Ergonomics, Energy, Ecology and

Emission, TCO: Swedish Confederation of Professional Employees) for TCO versions

RETURN TO TOP OF THE PAGE

Energy Star Declaration

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20...0CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/regs/regulat.htm (2 of 10)2006-12-4 15:16:17

Regulatory Information

This monitor is equipped with a function for saving energy which supports the VESA Display

Power Management Signaling (DPMS)

standard. This means that the monitor must be

connected to a computer which supports VESA DPMS. Time settings are adjusted from the

system unit by software.

VESA State LED Indicator Power Consumption

Normal operation ON (Active) Green < 36 W (typ.)

Power Saving

Alternative 2

One step

OFF (Sleep) Amber < 1 W

Switch Off Off < 1 W

As an ENERGY STAR

®

Partner, PHILIPS has determined that this product meets

the

ENERGY STAR

®

guidelines for energy efficiency.

We recommend you switch off the monitor when it is not in use for a long time.

RETURN TO TOP OF THE PAGE

Federal Communications Commission (FCC) Notice (U.S. Only)

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

● Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

Use only RF shielded cable with ferrite core that supplied with the monitor when connecting this monitor to a computer

device .

If your RF shield cable without ferrite core, we recommend to contact with Philips Customer & Service center for more

information.

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20...0CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/regs/regulat.htm (3 of 10)2006-12-4 15:16:17

Regulatory Information

To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or

excessive moisture.

THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN

INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.

RETURN TO TOP OF THE PAGE

FCC Declaration of Conformity

Trade Name: Philips

Responsible Party:

Philips Consumer Electronics North America

P.O. Box 671539

Marietta , GA 30006-0026

1-888-PHILIPS (744-5477)

Declaration of Conformity for Products Marked with FCC Logo,

United States Only

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

RETURN TO TOP OF THE PAGE

Commission Federale de la Communication (FCC Declaration)

Cet équipement a été testé et déclaré conforme auxlimites des appareils numériques de

class B,aux termes de l'article 15 Des règles de la FCC. Ces limites sont conçues de façon

à fourir une protection raisonnable contre les interférences nuisibles dans le cadre d'une

installation résidentielle. CET appareil produit, utilise et peut émettre des hyperfréquences

qui, si l'appareil n'est pas installé et utilisé selon les consignes données, peuvent causer

des interférences nuisibles aux communications radio. Cependant, rien ne peut garantir

l'absence d'interférences dans le cadre d'une installation particulière. Si cet appareil est la

cause d'interférences nuisibles pour la réception des signaux de radio ou de télévision, ce

qui peut être décelé en fermant l'équipement, puis en le remettant en fonction, l'utilisateur

pourrait essayer de corriger la situation en prenant les mesures suivantes:

● Réorienter ou déplacer l'antenne de réception.

● Augmenter la distance entre l'équipement et le récepteur.

● Brancher l'équipement sur un autre circuit que celui utilisé par le récepteur.

● Demander l'aide du marchand ou d'un technicien chevronné en radio/télévision.

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20...0CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/regs/regulat.htm (4 of 10)2006-12-4 15:16:17

Regulatory Information

Toutes modifications n'ayant pas reçu l'approbation des services compétents en matière de

conformité est susceptible d'interdire à l'utilisateur l'usage du présent équipement.

N'utiliser que des câbles RF armés pour les connections avec des ordinateurs ou périphériques.

CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU

REGLEMENT SUR LE MATERIEL BROUILLEUR DU CANADA.

RETURN TO TOP OF THE PAGE

EN 55022 Compliance (Czech Republic Only)

RETURN TO TOP OF THE PAGE

MIC Notice (South Korea Only)

Class B Device

Please note that this device has been approved for non-business purposes and may be used in any

environment, including residential areas.

RETURN TO TOP OF THE PAGE

Polish Center for Testing and Certification Notice

The equipment should draw power from a socket with an attached protection circuit (a three-prong

socket). All equipment that works together (computer, monitor, printer, and so on) should have the same

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20...0CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/regs/regulat.htm (5 of 10)2006-12-4 15:16:17

Regulatory Information

power supply source.

The phasing conductor of the room's electrical installation should have a reserve short-circuit protection

device in the form of a fuse with a nominal value no larger than 16 amperes (A).

To completely switch off the equipment, the power supply cable must be removed from the power supply

socket, which should be located near the equipment and easily accessible.

A protection mark "B" confirms that the equipment is in compliance with the protection usage

requirements of standards PN-93/T-42107 and PN-89/E-06251.

RETURN TO TOP OF THE PAGE

North Europe (Nordic Countries) Information

Placering/Ventilation

VARNING:

FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR

DU STÄLLER DIN UTRUSTNING PÅPLATS.

Placering/Ventilation

ADVARSEL:

SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT

ER NEMT TILGÆNGELIGE.

file:////Cnhszhmonams001/dev$/TPV_dev/TPV_ME/Old%20MDEV$/data/Coding%20...0CW7%20EDFU-V1-061204/lcd/manual/ENGLISH/190CW7/safety/regs/regulat.htm (6 of 10)2006-12-4 15:16:17

Page is loading ...

Philips 190CW7CB, 190CW7CB/00, 190CW7CB/69 User manual

Related papers

Other documents