Philips GC7057/20PERFECTCARE VIVA GC7052/30GC7055/20 PERFECTCARE VIVAPERFECTCARE VIVA GC7058/27GC7054/20 User manual

Page is loading ...

IMPORTANT

- Perform Calc-Clean process regularly for great steam and prolonged life (Fig. 1).

- Recommended water to use: distilled or demineralised water (Fig. 2).

IMPORTANT

- Eectuez régulièrement le traitement anticalcaire pour une vapeur de qualité et une

durée de vie prolongée (g. 1).

- Recommandation pour l’eau à utiliser : eau distillée ou déminéralisée (g. 2).

PENTING

- Menjalankan proses Calc-Clean secara teratur untuk penguapan yang baik dan masa

pakai yang panjang (Gbr. 1).

- Air yang disarankan: air suling atau tanpa campuran mineral (Gbr. 2).

중요사항

- 뛰어난 스팀 성능과 수명 연장을 위해서는 석회질을 정기적으로 제거하십시오 (그림 1).

- 권장 용수: 증류수 또는 정수된 물 (그림 2)

PENTING

- Lakukan proses Pembersihan Kerak secara berkala untuk stim yang hebat dan hayat

yang lebih panjang (Gamb. 1).

- Jenis air yang disyorkan: air suling atau air yang dinyahgalian (Gamb. 2).

IMPORTANTE

- Execute o processo Calc-Clean regularmente para um óptimo vapor e uma vida útil

prolongada (g. 1).

- Água recomendada para utilização: água destilada ou desmineralizada (g. 2).



-  ( 1)

- :  ( 2)

LƯU Ý QUAN TRỌNG

- Thường xuyên thực hiện quá trình Calc-Clean cho hơi nước tối ưu và kéo dài tuổi thọ của thiết

bị (Hình 1).

- Khuyến khích sử dụng: nước cất hoặc nước đã được khử khoáng (Hình 2).

CALC

CLEAN

1

CALC

CLEAN

1

12

2

12

2

4 5 6

15-30 min.

7

8 9

10

Press

2 sec.

11

2 min.

12 13

16

2

3

54

6

910

12

13

11

8 7

1

3

14

15

重要事項

- 定期執行除鈣程序，以達到良好蒸氣效果和延長壽命。

(

圖

1)

- 建議用水種類：蒸餾水或軟水。

(

圖

2)

注意事项

- 定期执行除垢流程可获得更出色的蒸汽和更长的使用寿命。

(

图

1)

- 建议使用的水：蒸馏水或软化水。

(

图

2)

Page is loading ...

6

Introduction

This iron has been approved by The Woolmark Company Pty Ltd for the ironing of

wool-only products, provided that the garments are ironed according to the

instructions on the garment label and those issued by the manufacturer of this iron.

R1401. In the United Kingdom, Eire, Hong Kong and India, the Woolmark trademark

is a certication trademark.

General description (Fig. 3)

1 Carry lock (specic types only)

2 Water tank lling funnel

3 Water tank

4 Iron platform

5 Supply hose

6 Mains cord with plug

7 Calc-Clean button with Calc-Clean light

8 On/o button with power-on light

9 ECO button with light

10 Soleplate

11 Steam trigger

12 ‘Iron ready’ light

13 Smart Calc-Clean container

OptimalTEMP Technology

The OptimalTEMP technology enables you to iron all types of ironable fabrics,

without adjusting the iron temperature.

- Fabrics with these symbols are ironable, for example linen, cotton, polyester, silk,

wool, viscose and rayon (Fig. 4).

- Fabrics with this symbol are not ironable. These fabrics include synthetic fabrics

such as Spandex or elastane, Spandex-mixed fabrics and polyolens (e.g.

polypropylene), but also prints on garments (Fig. 5).

Recommended water to use: distilled or demineralised water

Your appliance has been designed to be used with tap water. If you live in an area

with hard water, fast scale build-up may occur. It is therefore recommended to use

distilled or demineralised water to prolong the lifetime of your appliance.

Do not use perfumed water, water from the tumble dryer, vinegar, starch, descaling

agents, ironing aids, chemically descaled water or other chemicals, as they may

cause water spitting, brown staining or damage to your appliance.

Ironing

Please read the quick start guide on the packaging carefully to start using your

appliance.

Note: Keep the steam trigger pressed continuously when you move the iron over

the fabric while you iron.

ENGLISH

7

IMPORTANT - Cleaning and maintenance

Smart Calc-Clean System

Your appliance has been designed with a Smart Calc-Clean system to ensure that

descaling and cleaning is done regularly. This helps to maintain a strong steam

performance and avoids dirt and stains coming out of the soleplate over time.

To ensure that the cleaning process is performed, the steam generator gives regular

reminders. Besides that, a second defence step to protect the steam generator from

scale is integrated: the steam function gets disabled if descaling is not done after

1 hour steam ironing once the reminder came up. After descaling is done, the steam

function will be restored. This takes place regardless of the type of water used.

Sound and light Calc-Clean reminder

- After 1 to 3 months of use, the light of the Calc-Clean button starts ashing and

the appliance starts beeping to indicate that you have to perform the Calc-Clean

process (Fig. 6).

- You can continue steam ironing for 1 hour while the Calc-Clean light ashes and

the appliance beeps. After 1 hour, the steam function is automatically disabled.

You have to perform the Calc-Clean process before you can continue steam

ironing. (Fig. 7)

Performing the Calc-Clean process with the Calc-Clean container

Do not leave the appliance unattended during the Calc-Clean process.

Caution: Do not interrupt the process by lifting the iron up from the Calc-Clean

container, as hot water and steam will come out of the soleplate.

1 Fill up the water tank halfway (Fig. 8).

2 Make sure that the appliance is plugged in and switched ON during the

Calc-Clean process (Fig. 9).

3 Place the Calc-Clean container on the ironing board or any other even,

stable surface (Fig. 10).

4 Place the iron stably on the Calc-Clean container.

5 Press and hold the Calc-Clean button for 2 seconds until you hear short

beeps (Fig. 11).

Note: The Calc-Clean container has been designed to collect scale particles and

hot water during the Calc-Clean process. It is perfectly safe to rest the iron on this

container during the entire process.

6 During the Calc-Clean process, you hear short beeps and a pumping sound.

Wait approximately 2 minutes for the appliance to complete the

process (Fig. 12).

7 When the Calc-Clean process is completed, the iron stops beeping (Fig. 13).

8 Wipe the iron with a piece of cloth and put it back on the base station (Fig. 14).

9 As the Calc-Clean container becomes hot during the Calc-Clean process, wait

approx. 5 minutes before you touch it.

10 Carry the Calc-Clean container to the sink, empty it and store it for future

use (Fig. 15).

ENGLISH

8

11 If necessary, you can repeat steps 1 to 10. Make sure that you empty the

Calc-Clean container before you start the Calc-Clean process.

Note: During the Calc-Clean process, clean water may come out of the soleplate

if no scale has accumulated inside the iron. This is normal.

Energy saving

Eco mode

By using the ECO mode (reduced amount of steam), you can save energy without

compromising on the ironing result.

1 To activate the ECO mode, press the ECO button. The green ECO light goes

on. (Fig. 16)

2 To deactivate the ECO mode, press the ECO button again. The green light goes

o.

For the best results on tough fabrics you can use the TURBO mode.

1 Press and hold the on/o button for 2 seconds until the light turns white.

2 To deactivate the TURBO mode, press and hold the on/o button for 2 seconds

again until the light turns blue.

Safety auto-o (specic types only)

The safety auto-o function automatically switches o the appliance if it has not

been used for 5 minutes, to save energy.

Troubleshooting

This chapter summarises the most common problems you could encounter with the

appliance.

If you are unable to solve the problem with the information below, visit www.

philips.com/support for a list of frequently asked questions or contact the Consumer

Care Centre in your country.

Problem Possible cause Solution

The iron does not

produce any

steam.

There is not enough

water in the water

tank.

Fill the water tank beyond the MIN

indication. Press and hold the steam

trigger until steam comes out. It may

take up to 30 seconds until steam

comes out.

You have not pressed

the steam trigger.

Press and hold the steam trigger

until steam comes out.

The steam function

has been disabled

until you have

performed the Calc-

Clean process.

Perform the calc-clean process to

restore the steam function

(see chapter ‘IMPORTANT - Cleaning

and maintenance’).

The light of the

Calc-Clean

button ashes

and/or the

appliance beeps.

This is the Calc-Clean

reminder.

Perform the Calc-Clean process

within 1 hour after the Calc-Clean

reminder is given (see chapter

‘IMPORTANT - Cleaning and

maintenance’).

ENGLISH

9

Problem Possible cause Solution

The light of the

Calc-Clean

button ashes

and the

appliance beeps

every time I press

the steam trigger.

No steam comes

out of the

soleplate.

You have not done or

have not completed

the Calc-Clean

process.

Perform the Calc-Clean process to

enable the steam function again

(see chapter ‘IMPORTANT - Cleaning

and maintenance’).

The appliance

has switched o.

The safety auto-o

function was activated.

This happens

automatically when

the steam generator

has not been used for

more than 5 minutes.

Set the on/o switch to ‘o’ position

and then to ‘on’ position.

The appliance

produces a loud

pumping sound.

The water tank is

empty.

Fill the water tank with water and

press the steam trigger until the

pumping sound becomes softer and

steam comes out of the soleplate.

Water droplets

come out of the

soleplate.

After the Calc-Clean

process, remaining

water may drip out of

the soleplate.

Wipe the soleplate dry with a piece

of cloth. If the light in the Calc-Clean

button still ashes and the appliance

still beeps, perform the Calc-Clean

process (see chapter ‘IMPORTANT

- Cleaning and maintenance’).

The Calc-Clean

process has not been

completed.

You have to perform the Calc-Clean

process again (see chapter

‘IMPORTANT - Cleaning and

maintenance’).

Dirty water and

impurities come

out of the

soleplate.

Impurities or chemicals

present in the water

have deposited in the

steam vents and/or

soleplate.

Perform the Calc-Clean process

regularly (see chapter ‘IMPORTANT

- Cleaning and maintenance’).

Water ushes out

of the soleplate.

You have accidentally

started the Calc-Clean

process (see chapter

‘IMPORTANT -

Cleaning and

maintenance’).

Switch o the appliance. Then switch

it back on again. Let the iron heat up

until the ‘iron ready’ light lights up

steadily.

ENGLISH

10

Problem Possible cause Solution

The Calc-Clean

process does not

start.

You have not pressed

the Calc-Clean button

for 2 seconds until the

appliance started

beeping.

See chapter ‘IMPORTANT - Cleaning

and maintenance’.

The iron leaves a

shine or an

imprint on the

garment.

The surface to be

ironed was uneven, for

instance because you

were ironing over a

seam or a fold in the

garment.

Perfect Care is safe on all garments.

The shine or imprint is not

permanent and will disappear when

you wash the garment. Avoid ironing

over seams or folds or you can place

a cotton cloth over the area to be

ironed to avoid imprints.

The ironing board

cover becomes

wet or water

droplets come

out of the

soleplate.

Steam has condensed

on the ironing board

cover after a long

ironing session.

Replace the ironing board cover if

the foam material has worn out. You

can also add an extra layer of felt

material under the ironing board

cover to prevent condensation on

the ironing board.

You may have an

ironing board that is

not designed to cope

with the high steam

rate of the steam

generator.

Put an extra layer of felt material

under the ironing board cover to

prevent condensation on the ironing

board.

Steam continues

to come out after

I release the

steam trigger.

Steam is generated in

the soleplate. When

you release the steam

trigger, remaining

water is transformed

into steam. This is

normal.

Release the steam trigger 2 to 3

seconds before you place the iron

back on the iron platform or ironing

board.

There is a strong

gush of steam

when I release

the steam trigger

after placing the

iron on the iron

platform.

When the iron is tilted

upwards, remaining

water is collected and

converted into strong

steam. This is normal.

Release the steam trigger 2 to 3

seconds before you place the iron

back on the iron platform or ironing

board.

Steam is weak. You do not press the

steam trigger

continuously.

Keep the steam trigger pressed

continuously when you move the

iron over the fabric.

ENGLISH

11

Problem Possible cause Solution

You use the ECO

mode.

For more steam, switch o the ECO

mode by pressing the ECO button.

The green ECO light goes o.

Steam does not

come out

immediately

when I press the

steam trigger.

Water is converted into

steam in the soleplate.

When you press the

steam trigger, it will

take 1 to 2 seconds

until steam is

generated and

released. This is

normal.

Keep the steam trigger pressed

continuously when you move the

iron over the fabric.

ENGLISH

Page is loading ...

Philips GC7057/20PERFECTCARE VIVA GC7052/30GC7055/20 PERFECTCARE VIVAPERFECTCARE VIVA GC7058/27GC7054/20 User manual

Philips GC7057/20PERFECTCARE VIVA GC7052/30GC7055/20 PERFECTCARE VIVAPERFECTCARE VIVA GC7058/27GC7054/20 User manual

in other languages

Related papers

Other documents