Renkforce Network adapter 1 Gbps Owner's manual

Brand: Renkforce

Model: Network adapter 1 Gbps

Category: Coffee making accessories

Type: Owner's manual

This manual is also suitable for

RF-3374950

Renkforce Network adapter 1 Gbps

The Renkforce Network Adapter 1 Gbps is a USB 3.1 Type C adapter that allows you to connect your computer to a network via an RJ45 cable. It supports network speeds of up to 1000 Mbps and is compatible with IEEE 802.3, 802.3u and 802.3ab standards. The adapter also supports full and half duplex operation over Ethernet and has a maximum transmission unit (MTU) of 9 kB.

The Renkforce Network adapter 1 Gbps is an ideal solution for connecting your computer to a network if you do not have a built-in Ethernet port or if you want to upgrade your network speed to 1 Gbps. It is also compatible with older USB standards, including USB 3.0 and below, is easy to install and does not require any additional drivers or software.

Renkforce Network adapter 1 Gbps

Page is loading ...

• Maintenance, modications and repairs must be carried out by a technician or a

specialist repair centre.

• If you have questions which remain unanswered by these operating instructions,

contact our technical support service or other technical personnel.

b) Persons and product

• Do not cover the USB network adapter. Always ensure sufcient ventilation of the

USB network adapter. It may heat up considerably during operation.

Operation

a) Driver installation, connection

• Connect the USB network adapter to a USB3.1 port (Type-C™) on a computer in order to

install the requisite drivers. The port must be able to supply a current of 800 mA.

• Connect the RJ45 port of the USB network adapter to your switch or router using a 1:1

connected network cable.

• Insert the supplied data carrier into the respective drive of your computer.

• The system automatically selects the appropriate drivers and installs them. Depending on

the operating system version, administrator rights may be required to install the drivers. If

installation does not start automatically, double click on the setup le to start the installation.

Follow the installation instructions and complete the installation.

• Check that the hoist was installed correctly. The driver must be displayed as “Realtek USB

Family Controller”. In Windows, you will nd it under “Network Adapter”. In other systems,

e.g. Linux, network devices may be displayed differently. See the operating instructions of

these systems for information on where the network devices can be found.

• You can also check the settings of the device, e.g. duplex mode, etc., and set them according

to your preferences.

• You may need to restart your operating system for the USB network adapter to work correctly.

• Your connected computer now has a network connection via the USB 3.1 port (Type-C™).

The enclosed data carrier has a link to the website to update the drivers to the latest

version. Follow the instructions to download new drivers and to update the USB

network adapter.

b) LED indicator

• The USB network adapter features an LED for function display with the following functions:

- LED ashes: Data transmission

- LED off: No network connection

Tips and useful information

• Only connect the USB network adapter to a USB3.1 port (Type-C™) on a computer. A USB

port with a lower specication is too slow.

• If you have a network or system administrator who is responsible for your network (for example

in a larger company), allow him or her carry out the connection and driver installation; do not

install the USB network adapter yourself.

• The stated maximum data transmission rate of 10/100/1000 MBit cannot, in practice, be

achieved. This is due to the transmission method used, transmission errors, other devices

on the network etc.

• If you are using Windows, it may take some time for a PC to appear on the network. When

you switch the computer on and Windows is loaded on all computers after a few seconds, you

cannot usually access another PC immediately.

• If, after a few minutes, it is still not possible to access other PCs, check any rewall and/or

virus scanner settings that may be used.

• Access permissions must also be set accordingly, if you are using an operating system that

offers such features.

• Consult the applicable operating instructions when using a network printer or other devices

on the network.

• There are numerous reasons as to why a network connection may not be successful.

• Please refer to the appropriate specialist literature or to a specialist technician.

- If you are not using a DHCP Server (e.g. integrated into all DSL-routers), you should assign

a xed IP address to each device on the network.

- For example, set the router to 192.168.1.1, set the rst computer to 192.168.1.2, the

second computer to 192.168.1.3, and so on.

- The rst three digits must be the same on all computers; the last digit can range from 1

to 254.

- The “subnet mask” must be set to 255.255.255.0 for all computers on the network.

- Please keep in mind that an IP address (such as 192.168.1.1) can only be used once on the

network. If you set your router to IP address 192.168.1.1, no other device on the network

can use this IP address!

Operating instructions

USB-C GIGABIT NETWORK ADAPTER

Item no. 1687475

Intended use

The product is intended for connection to a USB3.1 port (Type-C™) on a computer, where

it makes a network port with 10/100/1000 Mbps speed available via a cable with RJ45

connection. The USB network adapter detects the possible speed automatically (auto-sensing)

and uses the highest possible. The auto-MDIX feature allows you to dispense with a crossover

cable for physical connection of two devices. For more information on the supported protocols

and functions, please see the “Technical data”.

This product is intended for indoor use only. Do not use it outdoors. Contact with moisture (e.g.

in bathrooms) must be avoided under all circumstances.

For safety and approval purposes, you must not rebuild and/or modify this product. Using the

product for purposes other than those described above may damage the product. In addition,

improper use can cause hazards such as a short circuit or re. Read the operating instructions

carefully and store them in a safe place. Make this product available to third parties only

together with its operating instructions.

This product complies with statutory, national and European regulations. All company and

Delivery content

• USB network adaptor

• Data carrier with drivers

• Operating instructions

Up-to-date operating instructions

To download the latest operating instructions, visit www.conrad.com/downloads or scan the QR

code on this page. Follow the instructions on the website.

Explanation of symbols

The symbol with an exclamation mark in a triangle is used to highlight important

information in these operating instructions. Always read this information carefully.

The arrow symbol alerts the user to the presence of important tips and notes on

using the device.

Safety information

Read the operating instructions and safety information carefully. If you do

not follow the safety information and information on proper handling in these

operating instructions, we will assume no liability for any resulting personal

injury or damage to property. Such cases will invalidate the warranty/

guarantee.

a) General information

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. It may become a

dangerous toy for children.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high

humidity, moisture, ammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of operation and

protect it from any accidental use. Safe operation can no longer be guaranteed

if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stress.

• Always handle the product carefully. Jolts, impacts or a fall even from a low height

may damage the product.

• Always observe the safety information and operating instructions of any other

devices which are connected to the product.

• Consult a technician if you are not sure how to use or connect the product, or if

you have concerns about safety.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method (e.g. photocopying, microlming or the capture in

electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.

This publication represent the technical status at the time of printing.

Care and cleaning

• Always disconnect the product from the power supply before cleaning it.

• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these could

damage the housing or stop the product from functioning properly.

• Use a dry, lint-free cloth to clean the exterior of the product.

Disposal

Electronic devices are recyclable waste and must not be disposed of in the

household waste. At the end of its service life, dispose of the product according to

the relevant statutory regulations.

You thus full your statutory obligations and contribute to protection of the environment.

Technical data

Power supply ................................ Via USB 3.1 Type C Gen 1

Current consumption .................... Max. 800 mA (with super/high/full speed with bus supply)

Network connection ...................... RJ45

USB standard ............................... USB3.1 (compatible with USB1.0/1.1/2.0/3.0)

Network standard ......................... Compatible with IEEE 802.3, 802.3u and 802.3ab

(10Base-T, 100Base-TX and 1000Base-T)

Network speed .............................. 10/100 to 1000 MBit

Operating mode ............................ Supports full- and half-duplex mode via Ethernet Maximum

Transmission Unit (MTU), supports Jumbo frames up to

9 kB

Network cable ............................... Auto-MDIX (crossover and uncrossed)

Remote control via network .......... Magic Packet

support, Wake On LAN

TCP Ofoad .................................. For IPv4 and IPV6 with Ofoad Engine (TOE) for

checksums.

Transport layer protocols .............. TCP/UDP (for IPv6 and IPv4)

Internet layer protocols ................. IP, ICMP/IGMP & ICMPv6

Hardware requirements ................ CPU 1.2 GHz or faster, 1 GB RAM or more

Supported operating systems ....... Windows

, Vista™ (32/64 Bit), 7 (32/64 Bit),

8.0 (32/64 Bit), 8.1 (32/64 Bit), 10.0 (32/64 Bit), 10S, RT,

Mac OS 10.2 or higher, Linux

Driver CD ...................................... Diameter 8 cm

Cable length ................................. Approx. 6 cm

Operating conditions ..................... 0 to +40 °C, 0 - 90 % relative humidity (non-condensing)

Storage conditions ........................ -10 to +70 °C, 0 - 90 % relative humidity (non-condensing)

Dimensions (L x W x H) ................ 29 x 16 x 64.5 mm

Weight .......................................... 35.3 g

Page is loading ...

Renkforce Network adapter 1 Gbps Owner's manual

Brand: Renkforce

Model: Network adapter 1 Gbps

Category: Coffee making accessories

Type: Owner's manual

This manual is also suitable for

RF-3374950

Renkforce Network adapter 1 Gbps

Download PDF

report

in other languages

français: Renkforce Network adapter 1 Gbps Le manuel du propriétaire
Deutsch: Renkforce Network adapter 1 Gbps Bedienungsanleitung
Nederlands: Renkforce Network adapter 1 Gbps de handleiding

Renkforce Network adapter 1 Gbps Owner's manual

This manual is also suitable for

Renkforce Network adapter 1 Gbps Owner's manual

in other languages

Related papers

Other documents