Shark SS460 User manual

Category
Steam cleaners
Type
User manual
2 1-800-798-7398
WHEN USING YOUR SHARK
®
STEAM & SPRAY
PRO MOP, BASIC SAFETY PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED, INCLUDING
THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING
YOUR SHARK
®
STEAM & SPRAY
PRO MOP.
DANGER OF SCALDING.
Please use caution when using the steam mop. The
steam emitted from the steam mop is very hot.
POLARIZED PLUG
To reduce the risk of electric shock, this appliance
has a polarized plug (one blade is wider than the
other). As a safety feature, this plug will fit into a
polarized outlet only one way. If the plug does not
fit fully into the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. DO NOT
force into outlet or try to modify to fit.
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
When using an electrical appliance, basic safety precautions
should always be observed, including the following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
CAUTION: Keep all Shark
®
branded cleaners out of
the reach of children. Eye irritant. Should some of
the Shark
®
branded cleaners be rubbed or splashed
into the eyes, wash out thoroughly with water. If
irritation continues, contact a physician. In case of
ingestion, drink 16 FL. oz. (2 cups) of water.
WARNING: Your Shark
®
Steam & Spray
Pro
Mop is designed to clean hard floor surfaces. Do
not use on wood or tile floors that are highly worn,
unfinished or have a wax or oil finish. Surfaces
that have been treated with wax or some no wax
floors may be damaged by the cleaning solutions,
therefore, it is always recommended to test an
isolated area of the surface to be cleaned before
proceeding. You should always check the use and
care instructions from the floor manufacturer.
CAUTION - SHOCK HAZARD. To provide continued
protection against shock, disconnect from power
supply when not in use.
1 DO NOT use outdoors.
2 Unplug from electrical outlet when not in use and
before servicing.
3 DO NOT leave the appliance unattended when
plugged in. Always unplug the power cord from the
electrical outlet when not in use or before servicing.
Remove the 4 AA batteries if the appliance will not
be used for an extended period of time.
4 If hard floor cleaner is not working as it should, has
been dropped, damaged, left outdoors, or dropped
into water, return it to EURO-PRO Operating LLC
for examination, repair, or adjustment. Incorrect re-
assembly or repair can cause a risk of electrical shock
or injury to persons when the appliance is used.
3www.sharkclean.com
5 DO NOT attempt to repair. No user serviceable parts
inside.
6 DO NOT handle plug or hard floor cleaner with wet
hands or operate the appliance without shoes.
7 DO NOT run the hard floor cleaner over the power
cord, close a door on the cord or pull cord around
sharp corners.
8 DO NOT use an extension cord.
9 DO NOT allow the appliance to be used as a toy.
Close supervision is necessary when used by or near
children, pets or plants.
10 DO NOT use for space heating purposes.
11 DO NOT put any objects into openings. DO NOT use
with any opening blocked.
12 Use only on flat, horizontal surfaces. DO NOT use on
walls, counters or windows.
13 DO NOT put hands or feet under the hard floor
cleaner.
14 Keep hair, loose clothing, fingers and all parts of the
body away from openings and moving parts.
15 Do not immerse in water.
16 Use only as described in this manual.
17 To reduce the risk of fire and electric shock - use
ONLY SHARK
®
cleaning solutions intended for use
with this appliance.
18 DO NOT add any cleaning solutions in the Shark
®
Steam & Spray
Pro Mop other than the Shark
®
cleaners. Use of other scented perfumes, oils, or any
other chemicals may damage or clog the unit and
void the warranty.
19 DO NOT mix other cleaners with the Shark
®
cleaners as this could affect the effectiveness of the
appliance.
20 NEVER use the Shark
®
Steam & Spray
Pro Mop
to clean up or absorb flammable or combustible
materials.
21 DO NOT leave the Shark
®
Steam & Spray
Pro Mop
in one spot on any surface for any period of time
with a wet cleaning pad attached as this will damage
your floors.
22 When cleaning the Shark
®
Steam & Spray
Pro Mop
unplug the power cord from the electrical outlet and
clean with a dry or damp cloth. Do not pour water or
use alcohol, benzene or paint thinner on the unit.
23 Unplug the appliance before attaching the different
mop heads or attaching or removing the pads.
24 Use extreme caution when using this appliance to
clean stairs.
25 Only use manufacturer’s recommended attachments.
26 DO NOT use the Shark
®
Steam & Spray
Pro Mop
steam head without a pad attached.
27 DO NOT leave the batteries in the unit. Remove the
batteries when not in use.
28 DO NOT incinerate batteries or expose to high
temperatures. They may explode.
29 This unit is not intended for use with rechargeable
batteries. Use of rechargeable batteries can damage
the unit or lead to other hazards.
30 Leaks from battery cells can occur under extreme
conditions. If the liquid, which is 20-35% solution of
potassium hydroxide, gets on the skin wash quickly
with soap and water or neutralize with a mild acid
such as lemon juice or vinegar. If the liquid gets
into the eyes, flush them immediately with clean
water for a minimum of 10 minutes. Seek medical
attention.
31 Keep your work area well lit.
32 Store the Shark
®
Steam & Spray
Pro Mop indoors
in a cool, dry place.
33 To avoid circuit overload, do not operate another
appliance on the same socket (circuit) as the Shark
®
Steam & Spray
Pro Mop.
SAVE THESE
INSTRUCTIONS
8 1-800-798-7398
Euro-Pro, Shark, Steam & Spray, and SaniFiber are
trademarks of Euro-Pro Operating LLC. All other brand
names may be trademarks of their respective owners.
Thank you for purchasing the Shark
®
Steam & Spray
Pro Mop. This Owner’s Guide is designed to help you get a
complete understanding of your new hard floor cleaner. Please read it carefully and keep for future reference.
For a list of what is included with this model, refer to inside flap of box.
We are constantly striving to improve our products, therefore the specifications contained herein are subject to change
without notice.
If you should have a question about your Shark
®
Steam & Spray
Pro Mop, please call the Shark
®
Customer service
line at 800-798-7398.
REGISTER YOUR PURCHASE:
www.sharkclean.com
1-800-798-7398
RECORD THIS INFORMATION:
Model Number: _________________________________________
Date of Purchase (Keep receipt): _________________________
TECHNICAL SPECIFICATIONS:
Voltage: 120V., 60Hz
Watts: 1050W
10 1-800-798-7398
a Handle
b Spray Button
c Steam Head
d Spray Head
e Disposable Cleaning Pad (
XP1DISP)
f Washable Cleaning Pad (
P141GHF)
g Steam Energized Hard Floor Cleaner
(XRTU20HF)
h Filling Flask
AA Batteries (4 pack) (not shown)
h
c
d
e
f
a
b
g
NOTE: Select cleaning accessories are included. Others
are available for purchase at www.sharkclean.com or by
calling 1-800-798-7398 .
For a list of what is included with this model, refer to
inside flap of box.
12 1-800-798-7398
3 Connect the body of the unit with the selected
mop head. If selecting the steam head, you have
the option of filling the steam head at the sink or
using the fill flask to fill the water tank. Plug into the
electrical outlet. (fig. 3)
NOTE: To prolong the life of your Shark
®
Steam &
Spray
Pro Mop, we recommend using distilled water.
4 Insert the selected cleanser into the unit. Push it
down to make sure that it is well inserted. You will
hear an audible “click” when the cleanser bottle is
inserted properly. (fig. 4)
NOTE: To remove the Cleanser bottle, hold it and
pull it up.
IMPORTANT: Always make sure that the Shark
®
Steam
& Spray
Pro Mop is UNPLUGGED from the wall. It is
recommended to remove the batteries while the unit is
not in use. Use ONLY Cleansers supplied by Shark
®
. The
addition of other chemicals or cleaning solutions may
damage the appliance, void the warranty and could be
unsafe for you and your family.
1 Insert the top part of the pole into the bottom part of
the pole. Push the two parts together until you hear
it “click” into place. (fig. 1)
2 Remove the battery cover and insert the 4 AA
batteries. Replace the battery cover. (fig. 2)
fig. 1
fig. 2
AA
AA
AA
AA
fig. 3 fig. 4
14 1-800-798-7398
4 Plug into an electrical outlet.
5 Attach the cleaning pad onto the bottom of the steam
head. (fig. 5)
6 Lightly step on the back of the steam head to release the
handle to start automatic electronic steaming. (fig. 6)
7 Press the Spray Button to apply cleaning solution to
sticky stuck on messes as needed. Repeat until the
entire floor is cleaned. No rinsing is required. (fig. 6)
8 Once finished, step on the pad and lift the unit to
remove the pad. (fig. 7)
9 Unplug the steam head from the electrical outlet and
press the head release button to remove from the
main body of the unit. (fig. 8)
IMPORTANT: Never leave the steam head with a damp
pad on any floor surface for any amount of time as this
may damage the floor.
STEAM & SPRAY CLEANING
WARNING: Do not use on unsealed wood or unglazed
ceramic floors. Do not use on wood or tile floors that
are highly worn, unfinished or have a wax or oil finish.
It is always recommended to test an isolated area to be
cleaned before proceeding. You should always check the
use and care instructions from the floor manufacturer.
IMPORTANT: When cleaning with the steam head, make
sure that either the disposable or the washable cleaning
pad is attached to the bottom of the steam head.
IMPORTANT: Always make sure the floors are swept or
vacuumed before steam cleaning.
1 Connect the body of the unit with the steam head.
(fig. 5)
2 Open the filling hole on the steam head and fill with
water. (fig. 5)
3 Insert the Steam Energized Hard Floor cleanser into
the unit. (fig. 5)
MOP HEAD
RELEASE
fig. 5 fig. 6 fig. 8
fig. 7
16 1-800-798-7398
2 Insert the Steam Energized Hard Floor cleanser into
the unit. (fig. 9)
3 Attach the cleaning pad onto the bottom of the spray
head. (fig. 9)
4 Press the Spray Button to apply solution to the floor
that is to be cleaned. Repeat until the entire floor is
cleaned. No rinsing is required. (fig. 10)
5 Once finished, step on the pad and lift the unit to
remove thepad. (g. 11)
IMPORTANT: Never leave the spray head with a damp
pad on any floor surface for any amount of time as this
may damage the floor.
HARD FLOOR MOPPING
WARNING: Do not use on unsealed wood or unglazed
ceramic floors. Do not use on wood or tile floors that
are highly worn, unfinished or have a wax or oil finish.
It is always recommended to test an isolated area to be
cleaned before proceeding. You should always check the
use and care instructions from the floor manufacturer.
IMPORTANT: When cleaning with the spray head, make
sure that either the disposable or the washable cleaning
pad is attached to the bottom of the spray head.
IMPORTANT: Always make sure the floors are swept or
vacuumed before cleaning.
1 Connect the body of the unit with the spray head.
(fig. 9)
fig. 9
g. 10
g. 11
18 1-800-798-7398
F A Q
Q The Shark
®
Steam & Spray
Pro Mop leaves a
foam on hard floors.
A The cleaning pad is likely too saturated.
Replace with a clean, dry pad.
Q My floors seem cloudy after cleaning.
A The cleaning pad may be dirty. Replace with a
clean pad.
OR
A Shark
®
Steam & Spray
Pro Mop washable
cleaning pad was washed with a powder
detergent and may be damaged and require
replacement. Never use powder detergents.
Only use liquid detergent to launder the
washable cleaning pad.
OR
A Shark
®
Steam & Spray
Pro Mop may have
been left in the same spot for too long with a
wet cleaning pad. Never leave the unit with a
wet pad in one spot for too long.
OR
A This may be leftover from past cleaners that
were used on the floor surface. Use the Steam
Energized Hard Floor Cleaner a few more times
and see if the leftover cloudiness is removed. If
this does not work, we suggest rinsing the floor
with water and letting it dry. One or more rinses
generally removes the residue. A more stubborn
case may require you to rinse the floor with a
mix of one part vinegar to 2 parts water. Then
use the Steam Energized Hard Floor Cleaner
again with a clean pad.
20 1-800-798-7398
CONSUMPTION & USAGE OF
CLEANSERS & PADS
Consumption / Usage
Steam Energized Hard Floor
Cleaner
Use as necessary.
Washable Pad Replace after 20
washes.
GENERAL TIPS
• Changethecleaningpadfrequentlyforbestresults.
•  Always vacuum/sweep floors before cleaning.
MAINTENANCE & STORAGE
Care for the Washable Cleaning Pad
1 We recommend washing the cleaning pad
separate from other fabrics to avoid picking up lint.
Only use liquid detergent (no powder detergent).
Do not use any fabric softeners or bleach. Line dry
or dry on a low dryer setting.
Storing Shark
®
Steam & Spray
Pro Mop
2 Remove any cleaning pads from the bottom of the
Steam Head or the Spray Head.
3 Empty any water that is left in the water reservoir
of the Steam Head.
4 Remove the batteries from the main unit.
22 1-800-798-7398
TROUBLE-SHOOTING GUIDE
Cleaner not coming out from spray nozzle.
• Check to see that the batteries are inserted properly
into the battery compartment. If there are batteries,
then insert new ones.
• Makesurethatthecleanserbottleisinsertedall
the way in. You should hear an audible “click” when
inserted.
• Checkthatthereisenoughcleaningsolutioninthe
cleanser bottle. If not, then insert a new bottle.
• Theremaybeairinthesystem.Holddownthespray
button for 5 - 10 seconds until the solution comes out.
Shark
®
Steam & Spray
Pro Mop will not turn on.
• Makesurethatthebatteriesareinserted.
• MakesurethattheSteamHeadispluggedin.
Shark
®
Steam & Spray
Pro Mop will not make
steam.
• Makesurethatthereiswaterinthewatertank.
• MakesurethattheSteamHeadispluggedintoan
electrical outlet.
Shark
®
Steam & Spray
Pro Mop is squirting foam
from the spray nozzle.
• Thecleanerbottleisnotrmlyinsertedintotheunit:
Make sure that you hear an audible “click” when you
insert the cleaner bottle into the unit.
Shark
®
Steam & Spray
Pro Mop left a white spot
on the floor.
• Checktoseeifthecleaningpadissoakedthrough.
We recommend that replace the cleaning pad.
• Makesurethatthecleaningpadisattachedcorrectly.
Shark
®
Steam & Spray
Pro Mop leaves water on
theoor.
• Donotleavetheunitontheoorwithadamp
cleaning pad.
• Ifyouareusingtapwater,werecommendswitching
to distilled water.
• Makesurethatthecaponthewaterreservoirofthe
steam head is securely closed.
Floors are cloudy, spotty or streaky after cleaning.
• Thecleaningpadmaybedirty.Replacewitha
cleanone.
• Ifthewashablecleaningpadwaswashedwitha
powderer detergent, the it may be damaged and
require replacement.
• Thesteammopmayhavebeenleftinonespotfor
too long with a damp cleaning pad.
 This may be leftover from past cleaners that were
used on the floor surface. Use the Steam Energized
Hard Floor Cleaner a few more times and see if
the leftover cloudiness is removed. If this does not
work, we suggest rinsing the floor with water and
letting it dry. One or more rinses generally removes
the residue. A more stubborn case may require you
to rinse the floor with a mix of one part vinegar to
2 parts water. Then use the Steam Energized Hard
Floor Cleaner again with a clean pad.
25www.sharkclean.com
ONE (1) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a period of one
(1) year from the date of purchase when utilized for normal household use, subject to the following conditions, exclusions
and exceptions.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option.
This Limited Warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or
used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, abuse, negligent handling
or damage due to faulty packaging or mishandling in transit. This Limited Warranty does not cover damage or defects
caused by or resulting from damages from shipping or repairs, service or alteration to the product or any of its parts, which
have been performed by a repair person not authorized by EURO-PRO Operating LLC.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period, you
may return the complete appliance and accessories with proof of purchase and date, freight prepaid. For assistance with
warranty service options or customer support, please call our customer care and product specialists at 1-800-798-7398
or visit our website at www.sharkclean.com.
If the appliance is found by EURO-PRO Operating LLC to be defective, in EURO-PRO Operating LLCs sole discretion,
we will repair or replace it free of charge. Proof of purchase is required and a fee of $19.95 will apply to cover the cost
of return freight.*
Non-durable parts including, without limitation, filters, brushes and electrical parts which normally require replacement are
specifically excluded from warranty.
This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific obligations
expressly assumed by it under the terms of this Limited Warranty. In no event is EURO-PRO Operating LLC liable for
incidental or consequential damages to anyone of any nature whatsoever. Some states do not permit the exclusion or
limitation of incidental or consequential damages, so the above may not apply to you.
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state or
province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date
and to attach a tag to item before packing including your name, complete address and phone number with
a note giving purchase information, model number and what you believe is the problem with the item. We
recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the
outside of your package “ATTENTION CUSTOMER SERVICE”.
PRODUCT REGISTRATION
Please visit www.sharkclean.com or call 1-800-798-7398 to register your new Shark
®
product within ten (10) days of
purchase. You will be asked to provide the store name, date of purchase and model number along with your name and address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering you
acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying
instructions.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Shark SS460 User manual

Category
Steam cleaners
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages