Electrolux EFC9436X/S User manual

Page is loading ...

52

S Innehållsförteckning.............................................................. 2

N Innholdsfortegnelse ............................................................ 12

DK Indholdsfortegnelse ............................................................ 22

FIN Sisällysluettelo................................................................... 32

TR Ýçindekiler ........................................................................... 42

UK Contents ............................................................................ 52

Contents

Safety warnings .................................................................................................... 52

Description of the appliance.................................................................................. 53

How to use the hood ............................................................................................. 54

Maintenance and care........................................................................................... 56

Special Accessories .............................................................................................. 57

What to do if ......................................................................................................... 57

Technical assistance service ................................................................................. 58

Service and Spare Parts........................................................................................ 58

Guarantee Conditions ............................................................................................ 59

Technical Specifications ........................................................................................ 60

Installation ............................................................................................................. 60

Safety warnings

The hood is designed uniquely for non-professional use, in a domestic setting. It respects international quality

safety provisions and requisites. Safety measures cannot however eliminate all the risks of accidents.

Read the instructions, suggestions and warnings carefully before installing.

Pay particular attention to the texts with the triangular warning symbol beside them to avoid damage to people

and objects. We recommend keeping the instructions booklet, which must be supplied in case of sale or cession

of the hood to a third party.

Installation and assistance

• A specialised electrician must carry out any

electrical connection and a qualified person

must carry out the installation of the hood.

Installation of the work by unqualified personnel

can lead to malfunction of the hood and cause

damage to people and/or objects.

• The hood must be installed at least 50 cm above

the cooking top or electric cooker, or at least 65

cm above gas cookers or gas cooking tops.

• Respect the greater distances indicated in the

installation instructions of the cooking top.

• Check that the connection cable has not been

not crushed during installation.

• The hood is considered electrically disconnected

only when the plug is disconnected or the fuse

removed.

• Note that the discharge of the hood cannot be

connected to a conduit that is used to expel

fumes from apparatuses supplied by power

other than electricity, e.g. a boiler or a fireplace.

During use

• Never leave frying food, melted fats, paraffin or

other inflammable liquids remaining unattended

on the cooking top. In case of fire: Turn the

hood and the cooking top off immediately.

ATTENTION! Put the flame out with the cover

of a pan. Do not use water.

• It is forbidden to cook on the flame under the

hood because it may cause a fire. Remember

that overheated oil can begin to burn

spontaneously. Never leave frying food

unattended.

• The anti-fat filter of the hood must be cleaned

periodically to avoid fat dripping onto the

cooking top and causing a fire. Read the relative

“Maintenance and cleaning” chapter in the

instructions booklet.

Dismantling and disposal

Contact Elkretsen AB or the dealer for information

about dismantling and disposing of the product.

Otherwise connect to the www.elkretsen.se

site to

find the collection point nearest to you.

For products such as refrigerators and freezers

contact the local authorities to find out where they

can be demolished and disposed of.

53

Description of the appliance

Functions

There are two possible mode:

• Suction of air outside with a flue (optional) and

a discharge tube.

• Recirculating using a carbon filter (optional). .

Attention! The EFCR 943-941 models have been

designed exclusively as suction versions and must

therefore be connected to an external suction

system.

The discharge tube cannot be connected to a

flue of other apparatuses functioning with

sources of power other than electricity, e.g.

a boiler or a fireplace.

Accessories

The following accessories are supplied with the

hood:

• 1 cap complete with commands, lighting and

ventilation motor (the EFCR 943-941 models

lack the motor and must therefore be connected

to an external suction system);

• 1 telescopic flue consisting of an upper U

section and a lower U section;

• 1 montage template;

• 1 baffle (only the EFC 9436-9416 models);

• 1 plastic container with a wall consol for fixing

the hood, wall dowels and screws and the

documentation;

The following accessories can be ordered from

your dealer:

• Carbon filter, Type 20. An active carbon filter

must be used when the hood is connected to a

“recirculating” system.

Extraction mode

• In this mode fumes are extracted to the outside

via a hose connected to the coupling ring A.

Fig. 1.

• In order to obtain the best performance the hose

should have a diameter equal to the outlet hole.

Recirculation mode

Attention! The EFCR 943-941models have been

designed exclusively for extraction mode and must

therefore be connected to an external suction

system.

• The air is filtered through a charcoal filter and

returned to the kitchen.

• You will need an original charcoal filter Type 20

for the recirculation mode. (See Special

Accessories).

D

A

Fig. 1

54

How to use the hood - EFC/R 941/6

Control panel

• Best results are obtained by using a low speed

for normal conditions and a high speed when

odours are more concentrated.

Turn the hood on a few minutes before you

start cooking.

The hood should be left on after cooking for

about 15 minutes or until all the odours have

disappeared.

The control switches are located on the hood’s

front panel:

• the light switch switches the hood lamp ON

and OFF;

• ON/OFF switch Speed 1: used to turn the fan

off and to set the fan to speed 1.

• Speed 2: used to set the fan to speed 2.

• Speed 3: used to set the fan to speed 3.

Correct ventilation

If the cooker hood is to work correctly there must

be an under pressure in the kitchen. It is important

to keep the kitchen windows closed and have a

window in an adjacent room open.

Important

If the hood is used together, for example, with an

open-fire fireplace that takes air from the interior

of the house, an eddy of air may take place that

produces smoke in the room. Try opening a

window.

This does not concern the carbon filter version.

Light switch

ON/OFF switch

Speed 1

Speed 2

Speed 3

Fig. 2 - Correct ventilation

55

How to use the hood - EFC/R 943/6

Control panel

• Best results are obtained by using a low speed

for normal conditions and a high speed when

odours are more concentrated.

Turn the hood on a few minutes before you start

cooking.

The hood should be left on after cooking for

about 15 minutes or until all the odours have

disappeared.

The control switches are located on the hood’s

front panel:

A - Main switch, hood off.

B - Start and choice of motor speed 1-2-3-1-

2.........

C - Indicates speed 1 (LED).

D - Indicates speed 2 and saturation of the

grease filter (LED)

E - Indicates speed 3 and saturation of the

charcoal filter (LED) (flashing LED)

F - Indicates Intensive speed (LED).

G - Intensive speed on/off. The Intensive

speed runs for 5 minutes:

If the hood is on when the Intensive speed

is activated, the hood reverts to previous

speed after 5 minutes.

If the hood is off when the Intensive

speed is activated, the hood will be turned

off after 5 minutes.

To interrupt the Intensive speed, press

button A or B.

H - Light OFF

I - Light ON

Should the hood or the controls fail to operate:

disconnect the power supply for at least 5 seconds,

then turn the hood back on again.

Control device for grease and

charcoal filters

This hood is fitted with a device that signals when it

is necessary to clean the grease filter or the

charcoal filter (in the case of recirculation version

with charcoal filter).

On delivery, the hood is not supplied with an

charcoal filter, so the saturation indicator will be

disabled.

If the hood is to be used with a charcoal filter, the

saturation

indicator light must be enabled as follows:

Press buttons B and G simultaneously and hold

them for 3 seconds. At first only the grease filter

LED D will light up, but when the charcoal filter

LED E lights up the saturation indicator will be

enabled.

To disable it: Press buttons B and G again

simultaneously and hold

them for 3 seconds, until the charcoal filter LED E

goes out.

Grease filter LED (D)

LED D will start to flash when it is time to clean

the grease filter.

Cleaning will be necessary after 40 working hours.

Always comply with the maintenance instructions

for the grease filter.

Charcoal filter LED (E)

The charcoal filter LED E will start to flash when

the charcoal filter needs to be replaced.

This operation is necessary after approximately 160

working hours.

Resetting the saturation indicator

After cleaning or replacing the filters, press button

A for 3 seconds until the Led D or the Led E

stops flashing.

Warning! The resetting of the saturation indicator

MUST be donein stand-by, never disconnect the

hood from the mains.

Correct ventilation

If the cooker hood is to work correctly there must

be an under pressure in the kitchen. It is important

to keep the kitchen windows closed and have a

window in an adjacent room open.

Important

If the hood is used together, for example, with an

open-fire fireplace that takes air from the interior

of the house, an eddy of air may take place that

produces smoke in the room. Try opening a

window.

This does not concern the carbon filter version.

AB

CDE F G

HI

56

Disconnect the hood from the power supply before starting any maintenance work by disconnecting the

plug or removing the fuse.

Clean the filter often. Deposits of fat on the filter and on the walls of the evacuation conduit are a fire

danger if, for example, a cooker is left on (or in the case of other kinds of overheating).

Maintenance and care

Cleaning the hood

Clean the outside of the hood using a damp cloth

and a neutral detergent.

Never use products containing corrosive and

abrasive agents or inflammable substances.

Cleaning the grease filter

Clean the filter every month or every two months,

depending on how often the hood is used.

The more the filter is cleaned, the greater will be

the amount of fat it can capture.

To remove the filter- Fig. 3:

• Press the metal clips on the anti-fat filter

backwards and remove the filter downwards.

The filter consists of an aluminium grid upon which

the fat is collected.

Clean the filter with detergent, immersing it in hot

water or putting it in the dishwasher. Wait until the

filter is dry before mounting it again.

Attention! Putting it into the dishwasher can make

the filter fade.

Cleaning/replacing the charcoal

filter

The active carbon filter must only be used if the

hood is to be used in the recirculation mode. The

active carbon filters absorb fumes and smells.

Unlike other charcoal filters, the LONGLIFE

charcoal filter can be cleaned and reactivated. With

normal use the filter should be cleaned every

second month (when using the hood 2,5 hours per

day,on avarage). The best way to clean the filter is

in the dishwasher. Use normal detergent and

choose the highest temperature (65º C). Wash the

filter separately so that no food parts gets stuck on

the filter and later causes bad odours. To reactivate

the charcoal, the filter should be dried in an oven

for 10 minutes with a maximum temperature of

100º C.

After approximately three years of use, the

charcoal filter should be replaced with a new, as

the odour reduction capacity will be reduced.

• Fitting - Fig. 4

Remove the frame i which supports the filter h

by turning 90° the two knobs g.

Insert the charcoal filter inside the frame and

put all parts back in their place. Fig. 4.

• To remove proceed in the reverse order.

• Clean the inner housing using a hand hot

solution only(never use caustic detergents,

abrasive powders or brushes).

• Always specify the hood model code number

and serial number when ordering replacement

filters. This information is shown on the

registration plate located on the inside of the

unit.

• The charcoal filter can be ordered from your

local Service Force Centre.

Fig. 4

Fig. 3

h

i

g

h

g

57

Fig. 5

Changing the light bulb - Fig. 5

• Disconnect the cooker hood from the main

supply.

• Press (1) the lamp cover (2) and open it.

• Replace the old bulb with a new one of the

same type (3).

• Close the lamp cover.

3

1

2

Special Accessories

Charcoal Filter Type 20

External motor (for external installation) 942 122 035

External motor (for internal installation) 942 122 036

What to do if

If your appliance fails to work properly please carry out the following checks.

Symptom Solution

The cooker hood will not start... Check that: The hood is connected to the electricity supply.

Check that a fan speed has been selected

The cooker hood is not working Check that: The fan speed is set high enough for the task.

The grease filters are clean.

The kitchen is adequately vented to allow the entry of fresh air.

If set up for recirculation, check that the charcoal filter is still effective.

If set up for extraction, check that the ducting and outlets are not

blocked.

The cooker hood has The safety cut-out device has been tripped.

switched off during operation... Turn off the hob and then wait for the device to reset.

If the hood has been installed below the heights indicated in the

installation instructions the motor will cut-out frequently which will

damage the hood.

If after all these checks, the problem persists, contact your local Service Force Centre, quoting the model and

serial number.

Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls.

In-guarantee customers should ensure that the above checks have been made as the engineer will make a

charge if the fault is not a mechanical or electrical breakdown.

58

Technical assistance service

You are welcome to telephone our technical assistance service (see list of technical assistance centres)

whenever you need information or in the unlikely event of a fault.

For service in Australia call 1300 650 020.

When calling, please be ready to specify:

1. The model code number

2. The serial number (E-Nr.)

3. The manufacturing number (F-Nr.)

This information is shown on the registration plate inside the unit behind the grease filter.

We reserve the right to change specifications and colours as a result of our policy of continuing technological

development.

Service and Spare Parts

In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local

Service Force Centre by telephoning: 08705 929 929

Your call will be automatically routed to the Service Centre covering your post code area. For the address of

your local Service Force Centre and further information about Service Force, please visit the website at

www.serviceforce.co.uk

Please ensure that you have read the section „What to do if....“ as the engineer will make a charge if the fault is

not a mechanical or electrical breakdown even the appliance is under warranty. Please note that proof of

purchase is required for in-guarantee service calls.

Help us to help you

Please determine your type of enquiry before writing or telephoning.

When you contact us we need to know:

• Your name • Clear and concise details of the fault • Serial number*

• Address and post code • Name and model of the appliance*

• Telephone number • E number*

* This information can be found on the rating plate, which can be seen when the grease filters are removed.

If you require Customer Service in the Republic of Ireland please contact us at the address below:

Electrolux

Electrolux Group (Ire) Ltd

Long Mile Road

Dublin 12

Republic of Ireland

Tel: + 353 (0) 1 4090751

Email: [email protected]

CUSTOMER CARE DEPARTMENT

For general enquiries concerning your ELECTROLUX appliance or for further information on ELECTROLUX

products, please contact our Customer Care Department by letter or telephone at the address below or visit our

website at www.electrolux.co.uk

Customer Services Department

Major Appliances

Electrolux

Addington Way

Luton

Bedfordshire

LU4 9QQ

08705 950 950 (*) * calls to this number may be recorded for training purposes.

59

Guarantee Conditions

Standard guarantee conditions

We, Electrolux, undertake that if within 12 months of the date of the purchase this Electrolux appliance or any

part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option

repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:

The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.

The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s

instructions.

The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not

authorised by us.

All service work under this guarantee must be undertaken by an Electrolux Service Force Centre. Any appliance

or defective part replaced shall become the Company’s property.

This guarantee is in addition to your statutory and other legal rights.

Home visits are made between 8.30am and 5.30pm Monday to Friday.

Visits may be available outside these hours in which case a premium will be charged.

Exclusions

This guarantee does not cover:

Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or

removable parts of glass or plastic.

Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the

European Community (EC) or European Free Trade Area.

Appliances found to be in use within a commercial environment, plus those which are subject to rental

agreements.

Products of Electrolux manufacture which are not marketed by Electrolux.

European Guarantee

If you should move to another country within Europe then your guarantee moves with you to your new home

subject to the following qualifications:

The guarantee starts from the date you first purchased your product.

The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of

use for this brand or range of products.

This guarantee relates to you and cannot be transferred to another user.

Your new home is within the European Community (EC) or European Free Trade Area.

The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal

household.

The product is installed taking into account regulations in your new country.

Before you move please contact your nearest Customer Care centre, listed below, to give them details of your

new home. They will then ensure that the local Service Organisation is aware of your move and able to look

after you and your appliances.

France Senlis +33 (0)3 44 62 20 13

Germany Nürnberg +49 (0)800 234 7378

Italy Pordenone +39 (0) 800 117511

Sweden Stockholm +46 (0)20 78 77 50

UK Luton +44 (0) 8705 950 950

60

Installation

Unpacking

Check that the cooker hood has no damages.

Transportation damages should immediately be

reported to the company responsible for the

transportation.

Damages, faults and any missing parts or

documents should immediately be reported to the

retailer.

Take care of the packing materials so that small

children cannot play with them.

Fitting

The hood is to be mounted on the wall.

When installed, the hood must be not less than 50

cm. above electric burners or 65 cm. above gas or

mixed-fuel burners. Fig. 6.

The hood can be installed above these heights but

for optimum performance it should be installed at

the distance quoted for the appropriate heat source.

The discharge of the hood cannot be

connected to a conduit that is used for

expelling fumes from apparatuses supply by

power other than electricity, e.g. a boiler or

fireplace.

Electrical connection

The electrical point must be positioned inside the

flue. The hood has a supply cable and a plug pro-

vided with earth and a voltage of 230V.

Min

65 cm

Min

50 cm

Fig. 6

Technical Specifications

EFCR 943 EFC 9436 EFC 9416 EFCR 941

Dimensions (cm) Height 66 - 116 66 - 116 74,5 - 116 74,5 - 116

Width 89,8 89,8 89,8 89,8

Depth 50 50 50 50

Lighting 2 x 20 W 2 x 20 W 2 x 20 W 2 x 20 W

Grease filter 1 1 1 1

Electrical Connection 230 V 230 V 230 V 220-240 V

Power absorption 230 W* 215 W 200 W 230 W*

* External motor (for external installation) 942 122 035

External motor (for internal installation) 942 122 036

61

Mounting the hood on the wall –Fig. 8

Disconnect the hood from the power supply using the main switch of the house.

Remove the 2 screws inside the hood, below at the fixing points of the suction unit (also see operation 3-

removing the anti-fats filter/s or active carbon filter/s frame).

• Position the suction unit on a support and insert the lower part of the hood (1).

• Connect the two components electrically (2).

• Fix the hood to the suction unit using 8 screws (3).

• To facilitate the montage, draw a line corresponding to the centre of the apparatus (4), position the template

so that its centre corresponds to this line and the lower corner of the template corresponds to the lower

corner of the hood (5).

• Make two Ø 8 mm holes with a drill and fix the support to the wall with two dowels and two screws (6).

• Hang the hood up (7), adjust the position (8-9) and mark the hole from inside the hood for the definitive fixing

(10), remove the hood (11), make a Ø 8 mm hole with a drill (12), insert a wall dowel (13).

• Make two Ø 8 mm holes in the upper part, near the ceiling (14), insert two wall dowels and fix the support of

the flue with two screws (15).

• Hang the hood up again (16).

• Fix definitively with a screw (17).

• If the hood has to be used in a filtering version, mount a baffle F on the support of the flue (G) with four

2.9x6.5 screws and install a fumes discharge tube (18) to connect the exit of hood A with baffle F. If the

hood has to be used in a suction version, baffle F does not have to be installed and a fumes discharge tube

(18) has to be installed to connect hood exit A with the outside.

Attention! Only models EFCR 943-941: the discharge tube is to be connected to an external suction unit

(see successive paragraph “Connection to an external motor”).

• Connect electrically (19) but do not connect the hood to the main panel of the house.

Attention! Only models EFCR 943-941: It is also necessary to connect electrically to an external suction

motor (see successive paragraph “Connection to an external motor”.

• Fix the flue (20a) to the support (20b).

Let the lower section of the flue slide downward and insert it in the apposite housing on the upper part of the

hood.

Mount the frame of the active carbon filter and the anti-fats filter again, connect the hood to the power supply

and check that the hood is functioning correctly.

=

X

Fig. 7

Mounting the flue support

bracket (3 sections)

Fix the three sections with 4 screws, adjust the

width of the support on the basis of the internal

width of the flue. Fig. 7

Page is loading ...

63

N

B

S

L

Tube

Electrical cable

H05 VVF (3x0.75).

Connection to an external motor

Only for models EFCR 943-941

The hood is not equipped with an internal motor

and must be connected to an external motor (to

purchase separately).

The electrical connection must be made with the

help of suitable attachments.

Attention! Only use an external motor

supplied by the constructor.

Connecting the discharge tube to the external

motor.

The external motor must be installed in a

reasonably spacious point, respecting the

regulations in force.

The external motor must be connected to the hood

with a discharge tube having an adequate diameter

(min. 150 mm).

Note that the longer the discharge tube is, the less

effective will be the suction effect. The length of

the discharge tube must not be more than 7 metres

in any case.

All the materials needed for connecting the hood to

the external motor (tubes, electrical cables, etc.)

are not supplied and must be purchased separately.

Electrical connection of the external motor

• Check the position of branching box B

positioned over the hood.

• Remove the S screws and open the cover of

box B.

• Open the cable holder and remove the L

screws.

• Use a (3x0.75) type cable to connect the hood.

• Connect the clamps of the motor cable on the

terminal board in branching box B to the hood.

• Close the cable holder with the L screws.

• Close cover B and fix the S screws.

• Connect the hood to the power supply.

Fig. 9

External motor (for external installation)

942 122 035

Internal motor (for internal installation)

942 122 036

LI2EXD Ed. 05/06

The Electrolux Group. The world´s No.1 choice.

The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million

Electrolux Group products (such as refrigerators, cookers, washing machines,vacuum cleaners, chain saws and lawn mowers) are sold each

year to a value of approx. USD 14 billion in more than 150 countries around the world.

Electrolux HemProdukter AB

S-105 45 Stockholm

www.electrolux.se

Electrolux Home Products

Risløkkveien 2

0508 Oslo

Tlf: 81 53 02 22

E-mail: [email protected]

Internett: www.electrolux.no

Electrolux Husholdningsapparater A/S

Lundtoftevej 160

2800 Lyngby

Tlf: 45 87 70 88

Oy Electrolux Ab

Pakkalankuja 6

01510 VANTAA

Puh. 0200-2662 (0,1597 •/min+pvm)

Electrolux EFC9436X/S User manual

This manual is also suitable for

Electrolux EFC9436X/S User manual

in other languages

Related papers

Other documents