Electrolux EQ98X User manual

important safety instructions 1

warning

• This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

• Children should be supervised to ensure that they don’t

play with the appliance

• Accessible parts may become hot during use. To avoid

burns, young children should be kept away.

• Children should not play with the plastic bags or lms,

please keep these materials out of the reach of children

at all times to avoid any possibility of suffocation.

caution

If you nd the appliance is damaged or marked, you must

report it within 7 days if you wish to claim for damage/

marks under the manufacturer’s warranty.

This does not affect your statutory rights.

Please read the user manual carefully and store in a handy

place for future reference. Meanings of the symbols used in

this manual are shown below:

warning

This symbol indicates information concerning your

personal safety

caution

This symbol indicates information on how to avoid

damaging the appliance

tips and information

This symbol indicates tips and information about use

of the appliance

environmental tip

This symbol indicates tips and information about

economical and ecological use of the appliance

This symbol indicates never to do this

This symbol indicates always to do this

For your safety please read this book before

operating your microwave oven.

warning

Improper installation, adjustment, alteration or

maintenance can cause injury or property damage.

Please contact your nearest Electrolux Service

Department for additional information or assistance

for an approved installer.

NOTE TO THE INSTALLER

THIS MANUAL MUST REMAIN WITH THE OWNER FOR

FUTURE REFERENCE

Important safety instructions

2 important safety instructions electrolux keyhole cooktop

caution

Before using your cook top

• READ ALL the Warning and Safety information.

• Remove all packaging materials, plastic lms and any tags

or stickers.

• If you nd any damage on your cook top, please do not

connect it to the gas or electricity and contact the local

after service centre of Electrolux or agency.

• This appliance may only be installed and connected by a

qualied person.

• Built-in appliances may only be used after they have been

built into suitable built-in units and work surfaces which

meet required building & local standards or regulations.

• After the product is installed and before using it for the

rst time wipe all top surfaces with a soft cloth using soap

water.

• If the appliance that has not been used for long time or

is installed (reinstalled) for the rst time it may take a few

attempts to light the gas burner because there is air in the

gas system. Please repeat ignition but allow a moment

between each attempt to allow gas to disperse.

warning

Read the following carefully to avoid an electric

shock or ﬁre.

It is important to use your new appliance safely.

Check these safety points before using your appliance

for the rst time.

warning

The appliance may only be installed and connected by a

qualied person.

warning

This appliance MUST be connected to an earthed

power socket.

Important safety instructions

warning

IMPORTANT SAFETY INSTRUCTIONS READ

CAREFULLY AND KEEP FOR FUTURE REFERENCE

This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety.

During use, this appliance becomes hot. Care should

be taken to avoid touching hot surfaces. To avoid

burns, young children should be kept away.

This appliance must not be used as a space heater.

Do not spray aerosols in the vicinity of this appliance

whilst it is in operation.

Do not store ﬂammable liquids or materials on, under

or near this appliance, eg. Aerosols, plastic ﬁlms,

plastic, cleaning chemicals or paper.

Do not remove the trivet and enclose the burner with

a wok stand as this will concentrate and deﬂect heat

onto the burner.

Do not place anything, (eg. asbestos mat or heat

diffuser) between pan and trivet as serious damage

to the appliance may occur.

Do not modify this appliance.

This appliance has been designed for built in

application only. It may only be used after correct

installation into suitable bench top which complies

with all mandatory standards.

In the event of faults with this appliance or damage

to the glass ceramic (cracks, or breakages), the

appliance must be switched off and disconnected

from the electrical supply, to prevent the possibility

of an electric shock.

Repairs to the appliance must only be carried out by

trained registered service technicians.

This appliance is not intended to be operated by

means of an external timer or separate remote

control system.

Cables from electrical appliances must not touch the

hot surface of the appliance or hot cookware.

The appliance must always be attended during use as

overheated fats and oils can ignite very quickly and is

a potential ﬁre hazard.

Turn off the induction cooking zone after each use.

Do not rely on the pan detector.

Users with implanted pacemakers should keep their

upper body at least 30 cm from induction cooking

zone when they are switched on.

This appliance should be used only for normal

domestic cooking and heating of food.

Children should be supervised to ensure they do not

play with this appliance.

Ensure burner caps and crowns are in their correct

position.

If gas burner does not light in 5 seconds, allow one

minute for gas to clear before trying again.

electrolux keyhole cooktop tips and information 3

Product features

• The gas burner on this appliance has accidental ame

extinction protection device

• Mains powered gas ignition for 100% reliable ignition

• Strong powerful gas burner with high thermal efciency

• Large stainless steel and removable spill bowl for easy

cleaning

• Cast iron trivets for reliable performance

• Powerful 2000W induction cooking zone with low power

function to maintain slow cooking

• Simple and easy to use induction controls

• Smooth easy to clean ceramic top

Spill bowl & cast trivet

warning

Never operate this appliance without the spill bowl

correctly ﬁtted.

This appliance is tted with a removable spillage bowl

for easier cleaning.

To remove the spillage bowl:

• First remove the cast iron trivet.

• Remove the burner caps & base.

• Now the bowl can be lifted out.

caution

If the burner has been used make sure all the

components are cool before handling them.

NOTE! The spillage bowl and the cast iron trivet are all

located in their correct positions by 3 stainless steel pins

(see above). Ensure whenever removing these parts that

they are correctly re-tted.

tips and information

• To avoid small children and pets unintentionally switching

the induction control on, we recommend activation of the

lock feature as a child safety device.

• In order to avoid a re, this appliance must be kept clean.

• Pot handles should be turned away from the front of the

bench to avoid spillage accidents.

• For maximum stability, ensure pots and pans are centrally

located on the trivets.

• Keep all air vents clear of obstructions on the underside of

this product.

• Risk of burns! Do not leave objects made of metal, such as

knives, forks, spoons and saucepan lids on the induction

cooking surface or near the burner, as they can get hot.

• Remove stickers and lm from the glass ceramic or

stainless steel surfaces before using the appliance.

• The glass ceramic can be damaged by objects falling

onto it.

• The edge of the glass ceramic can be damaged by being

knocked by the cookware.

• Cookware made of cast iron, stainless steel or with

damaged bottoms can scratch the glass ceramic if pushed

or pulled across the surface.

• Spillage from cookware can burn onto the glass ceramic

or stainless steel and should be removed at the earliest

opportunity.

• Do not use the cooking zones with empty cookware or

without cookware.

• To avoid damaging cookware and glass ceramics, do not

allow saucepans or frying pans to boil dry.

• Do not allow large cookware to overhang the appliance

onto adjacent bench top. This will cause scorching to the

bench top surface.

• Do not allow cooking pots or pans to intrude into the area

which is close to the controls.

• Ensure burner bodies and trivets are properly located.

• Some cookware may make noise when used on an

induction unit. These noises are the result of vibration of

the laminated material (sandwich construction) inside the

cookware and will not affect the operation or performance

of the appliance.

Tips and information General product information

INDUCTION

Trivets

warning

Never operate this appliance without the trivet

correctly ﬁtted.

This appliance is supplied with two trivets.

The large integrated trivet is for all pans and pots with a

diameter greater than 200mm. For pan sizes greater than

300mm this trivet also has a second level which raises

larger pans to ensure maximum performance.

The smaller auxiliary trivet is intended for use with all pans

and pots which have a diameter between 200-100mm.

This trivet is supported by the large trivet.

warning

Always ensure the pot is centrally located on the

trivet and is stable. The auxiliary trivet should be

used with small pans.

4 general product information/controls electrolux keyhole cooktop

Gas control

NOTE! The gas control turns anticlockwise from ‘OFF’ and

has limited movement.

Lighting burners

Electronic ignition: This appliance is tted with mains

powered ignition. When the appliance has been connected

and the power is on, depressing the knob will release

sparks at the burner.

caution

Keep hands clear of the burners when lighting.

• If burner does not light within 5 seconds, turn knob

to ‘OFF’ position, allow gas to disperse, then try

lighting again.

• Burners MUST be operated between ‘HIGH’ and

‘LOW’ settings only (see above).

To light a burner, the knob must be turned to the ‘HIGH’

position, then push down as far as possible and hold for

approximately 5 seconds. If the ame goes out when the

knob is released simply depress the knob again, this time

holding it down with slightly more force for the same length

of time.

The height and power of the ame can be varied by turning

the control knob toward the ‘LOW’ position.

In the absence of electrical power, carry out the ignition

directly to the burner with a hand held ignition source.

The burner on this appliance has an integrated ame

safeguard system which will automatically turn off the gas

if the ame sensor fails to detect a ame on the burner.

General product information Controls

Integrated trivet

Auxiliary trivet

electrolux keyhole cooktop controls 5

Induction control

Control Touch sensors

The induction zone is operated using control touch sensor.

Functions are controlled by placing a nger on the desired

touch sensor and conrmed by displays and acoustic

signals. Only place your nger on the touch sensor which

activates the desired function. Do not cover multiple touch

sensors at any one time.

tips and information

If one or more of the touch sensor is selected for longer

than 6 seconds, a signal will sound and the induction unit

will then switch itself off.

tips and information

If no control functions are selected within 10 seconds after

switching the induction unit on a signal sounds and the

induction unit will then switch itself off.

Controls

3456

1 Power – On/Off

2 Child lock

3 Heating level

4 Timer

5 Increase

6 Decrease

7 Display

8 Indicator light

Sensor ﬁeld Function

Power–On/Off Switch Induction unit On/Off

Child lock

Lock/unlock control touch sensors

for induction unit

Heating level

Adjust heat level from 0-9 (0=no

heat , 1=minimum & 9=maximum)

Timer

Set cook time from 1 minute – 2

hours

Increase Increase heat or time

Decrease Decrease heat or time

Display

Displays selected time or

remaining, power or other

functions

Indicator light Indicates which control is active

Display Function

Cooking zone is switched OFF

1-9 Heat settings

Heating level 1 = minimum to 9 =

maximum

E:88 Error / fault Error or fault has occurred

F Pan detection

Cookware not detected or not

suitable

H Residual heat Cooking zone is still hot

Lock

Lock is activated

–– Automatic off Automatic switch off has activated

warning

Risk of burns from residual heat.

After being switched off, the cooking zone will need some

time to cool down. Look at the display for the “

” symbol

to check temperature status. The display will clear when the

temperature falls to a safe level.

Removal of the pan from the heating zone for more than

10 seconds will cause the induction unit to switch off

automatically.

Switching the induction zone on and off

Step Control Panel Display Indicator light

Switch on Touch for

1 second

Lights up +

beeps

Switch off Touch for

1 second

H or

none

Goes out +

beeps

After switching on within approximately 10 seconds a heat

setting or a function must be set, otherwise the induction

unit will automatically switch itself off.

Setting the heating level

After switching on the power the heat level function is

activated automatically

Step Control Panel Display Indicator light

Increase

Touch

for

1 second

1-9

Lights up +

beeps

Decrease

Touch

for

1 second

9-0

Lights up +

beeps

Switch off

Touch

and

together

for 1 second

tips and information

To check the suitability of cookware for induction unit, a

magnet should stick to the bottom of the cookware. When

non-magnetic cookware is used the internal pot detection

will display “F” in the display area.

6 using your cooktop electrolux keyhole cooktop

Lock and unlock the control touch sensors

The induction touch sensors, with the exception of the

On/Off touch sensor, can be locked at any time in order

to prevent the settings being changed. These controls can

be locked whilst the unit is either On or Off.

Step Control Panel Display Indicator light

Switch on

Touch

for

4 seconds

L for 5

seconds

Lights up +

beeps

Switch off

Touch

for

4 seconds

none

Goes out +

beeps

tips and information

The lock function can prevent unintentional use of the

induction unit for example when cleaning.

warning

If the induction unit is on and the controls locked the

unit can still be turned off immediately if needed by

touching the

On/Off touch sensor.

warning

If you lock the induction unit controls after the unit

has been turned off, the lock indicator light and the

display will turn off after 5 seconds. When you want

to use the induction unit you will need to unlock the

controls ﬁrst.

Using the timer

The timer can be set to a maximum of 2 hours and the

display shows the time in hours & minutes. One minute is

displayed as “0:01” and one hour is displayed as “1:00”.

Step Control Panel Display Indicator light

Activate

Touch

for 1

second

Lights up

+ beeps

Increase

Touch

for 1

second or hold

00 to 2:00

Lights up

+ beeps

Decrease

Touch

for 1

second or hold

2:00 to 00

Lights up

+ beeps

Switch off

Touch

and

together

for 1 second

Lights up

on power

Using your cooktop

When the set time reaches “0” an audible signal (3X) will

sound. Select any touch sensor to stop the audible signal.

NOTE! The power will need to be turned off separately if

required.

tips and information

To change the set time simply select the or

touch

sensor anytime whilst the time is displayed.

When setting the time using the or

touch sensor,

the longer you hold your nger on the touch sensor the

faster the display changes.

When the timer is set and counting down if you wish to see

the power level setting, select the power touch sensor.

To return to timer display you will need to select the timer

touch sensor.

NOTE: If the control is locked, the unit must be unlocked

before any changes can be made.

Settings with no activity

Heat setting Switches off after

10 seconds

1-2

6 hours

3-4

5 hours

4 hours

6-9

1.5 hours

electrolux keyhole cooktop using your cooktop 7

The table shown below is intended as a guide only to

demonstrate possible uses for each power level and

provide some examples to give you an appreciation of

the performance level for each power level setting. The

examples shown and the cooking times will change

according to food type, food weight or thickness, total

quantity and recipe being followed. Larger or smaller

quantities of food, pan size, pan type and pan base

thickness whether the lid is on or off during cooking will all

impact on the cooking results and may require adjustment

of the power to a higher or lower setting to achieve the

desired results. We suggest you experiment and test your

favourite recipes to familiarise yourself with this products

performance.

Heat setting Cooking process Suitable for Tips / hints

zero power position

1-2

keeping warm or

melting

melting butter, chocolate or

dissolving leaf or granulated gelatine,

yolk or whole egg or butter sauces, milk

based dishes

without lid unless

otherwise stated in individual recipe

2-3

heating

cooking rice - absorption method,

cream or pulses (beans, lentils) soup,

keeping food hot, defrosting frozen

vegetables, omlettes, scrambled eggs,

porridge

Stir occasionally or as per specic

recipe instructions

3-4

simmering on

low heat

poaching sh or meat, poaching fruit,

re-heating previously cooked foods

Cook with lid on or as per specic

recipe instructions

4-5

steaming/cooking/

stewing

red & white meat, sh or vegetables,

rice other than absorption method,

dumplings

use at least twice as much liquid as

rice, stir milk dishes part way through

cooking or as per specic

recipe instructions

5-6

boiling

steamed desserts & sweet dumplings,

puddings, vegetables, sh or meat stews,

gentle braising, soups and broths

use at least 2 litres of liquid plus

ingredients or as per specic

recipe instructions

6-7

shallow frying

sh, red and white meat, eggs, stir fry,

frying without overheating oil, fat or

butter (ghee), pancakes, pasta

dumplings

turn half way through or as per

specic recipe instructions

7-8

deep frying

deep frying from frozen (sh and

chicken portions),

doughnuts, fried pizza

as per specic recipe

instructions

8-9

boiling

boiling large quantities of water

or boiling water to add pasta, steam

puddings etc, then turn down

as per specic recipe

instructions

8 care and cleaning electrolux keyhole cooktop

warning

Ensure the appliance is off and cool before cleaning.

caution

Harsh abrasive cleaners, powder cleaners, steel wool

or wax polishes should not be used.

Regular cleaning immediately after use is the easiest and

simplest method for keeping your appliance looking like

new. If soiling, oil and food spatter is allowed to remain on

the surfaces for long periods and allowed to bake onto

the surfaces, they will be more difcult to remove but then

when trying to remove them it is more likely damage to the

surface nish may result.

Stainless steel

Simply wipe with a soft cloth using warm water and a mild

detergent and rinse with clean water. Where stainless steel

has a heat tint or become extremely dirty or discoloured,

use a stainless steel cleaner.

Ceramic glass

The specially treated glass in the product is manufactured

using the latest technology to the highest possible

standards for both safety and reliability. However, it must be

remembered that as it is CERAMIC GLASS, it may break.

Treat it accordingly. To clean the ceramic glass hob use a

soft cloth or sponge with detergent and warm water.

warning

If the surface is cracked, switch off the appliance

immediately to avoid the possibility of electric shock.

If the ceramic surface is very soiled:

1. Remove soilage using a damp cloth or a plastic scraper.

2. Use a suitable stainless steel cleaner or ceramic cleaner

after sufcient time has passed for the top surfaces

to cool. Apply small quantities of cleaner onto the top

surface and wipe with a damp cloth or paper towel.

3. Use a damp cloth to remove all remaining traces of the

cleaner, which could otherwise burn on when the hob is

next used. Wipe the hob dry.

Ensure the appliance is off before using any metal

implements for cleaning the induction unit.

Care and cleaning of your cooktop

Trivets and burners

These can all be lifted off and removed for

separate cleaning.

NOTE! When retting the burner, ensure that they are

correctly seated.

Ensure burner is thoroughly dried after cleaning or spillage.

When cleaning the burner, ensure that all the ame ports

are free of any blockage. If necessary, use a toothpick or

brush to clear ports. In instances of heavy soiling, it may be

necessary to apply a non-abrasive cleaning compound and

rub with a cloth until the soiling is removed and then nish

with a soft, dry cloth.

Ignition spark plug and ame safeguard sensor

GENTLY clean the ignition spark plug and ame safeguard

sensor with a damp cloth to avoid lighting difculties. Ensure

the spark plug is always clean and dry before use.

electrolux keyhole cooktop installation 9

�

Installation

This appliance has had a full safety and performance

inspection before leaving the factory, do not disassemble

the appliance whilst installing it or connecting it to gas and

power.

Install this appliance into the bench top as described in this

section and ensure you read the instructions and warnings

carefully.

tips and information

A bench top cut-out template has been provided with this

appliance to assist with the installation and is located on the

top of the packaging.

tips and information

This product has special minimum requirements for air

circulation, refer to installation preparation for information.

warning

Only an authorised and qualiﬁed person should install

this appliance.

warning

The installation of this appliance must comply with all

national and local government regulations.

warning

Before using the appliance, ensure that all packing

materials are removed from the appliance.

warning

In order to avoid any potential hazard, the installation

instructions in this booklet, and any labels on the

appliance must be followed.

warning

Ensure that all speciﬁed vents, openings and air

spaces are not blocked.

warning

Where the appliance is built into a bench top, the bench

top material must be capable of withstanding 85°C.

warning

Failure to ﬁx the appliance into the bench correctly

could result in loosening of the gas connection

through movement of the appliance and a gas leak

may result. Please ensure the appliance can not move

inside the cut-out after installation and location clips

are all ﬁtted.

warning

Before installation check the gas supply and the gas

type marked on the appliance data plate match.

warning

After installation and connection the gas supply

pressure should be checked and the burner operated

to ensure correct operation.

Gas type

Gas type Nominal gas supply

pressure (kPa)

Thermal

efﬁciency (kW)

Burner

LPG (20Y) 2.8 4.0

Natural Gas

(10T,12T,13T)

2.0 4.0

Electrical connection

This appliance is supplied with a standard 10 Amp service

cord terminated by a 3-pin plug for connection to a

standard household socket. The electrical supply is required

to power the induction unit & electronic gas ignition system.

NOTE! It will be necessary for servicing purposes to

disconnect the electrical power supply. The power point

should therefore be accessible after the appliance is

installed, as specied in the local wiring regulations.

On page 10 is a schematic of the internal electrical wiring

for this appliance.

10 wiring electrolux keyhole cooktop

Internal wiring schematic

Faston Spade/tab

Ignition switch

Spark plug

Induction

power board

Fan motor

CHASSIS

EARTH STUD

DANGER - 220Vac

DISCONNECT FROM

POWER SUPPLY BEFORE

REMOVING ANY PANELS

Induction

coil

Induction

user interface

A1 A2

GND

FAN1

CONA

CONB-11

CON703

NTC

sensor

220Vac

50Hz

(10Amps)

Installation

Installation procedure

1. Remove the cut-out template from the top of the pack.

2. Place the cut-out template in the desired position and

secure to the bench top with adhesive tape.

warning

Before cutting check position of the appliance will not

be too close to combustible surfaces and complies

with see ﬁgures below.

warning

To operate correctly, the induction unit in this

appliance requires air to circulate freely. Refer below

for minimum internal cupboard requirements for

this hob.

Minimum distances to combustible surfaces

Allow maximum space for air circulation.

NOTE: If a barrier or partition is tted below the appliance at

the minimum position then openings should be included to

allow for air circulation. The cross sectional area of the open

area must be greater than 400cm

3. Cut out hole in bench top.

4. Remove all accessories from the pack and place in a

safe place.

5. Remove the appliance from the bottom of the pack and

place on stable surface.

6. Fit supplied foam tape to edges of hob. The thick section

tape is for the stainless steel bowl and the thinner section

tape for the edges of the ceramic glass, see gure below.

INDUCTION

130mm

Flammable surfaces

thin section tapethick section tape

clip

underside view of appliance

100mm

130mm

1000mm

Refer to manufacturers

specications for hood

clearance

Rangehood

Bench top

Barrier or partition See note below

120mm

clip

electrolux keyhole cooktop installation 11

12 installing your cooktop electrolux keyhole cooktop

7. Install seven positioning clips into special holes on the

sides of the appliance, see gures left and below.

8. Place appliance into cut-out and check the t. The

appliance should be a good t and not move in any

direction.

9. Fit the gas connection elbow to the end of the manifold

pipe. Ensure the sealing washer is inserted into the elbow

rst. Orient the elbow to the desired position and use two

spanners to tighten the connection, see diagram below.

10. Connect the gas supply tubing and ensure all the

connections are sound and gas tight.

11. Turn on the gas and check for gas leaks on all the

connections that have been made.

12. Plug in the appliance electrical supply cord into the

power socket.

NOTE: there will be a beep from the induction unit when the

power is switched on.

13. Operate burner to check ame quality & turndown

operation.

NOTE: When rst operating the burner it may take several

attempts to light the burner before all the air has been

expelled from the supply system.

A normal ame consists of inner and outer ame which

should be a blue colour. If the ame has yellow tips or is

noisy then it may be necessary to adjust the aeration. The

aeration adjustment control is located on the bottom of the

product see gure below.

Installation

aeration adjustment

1 2 3

manifold pipe

manifold nut

washer

elbow

metal tube

connection

elbow

rubber hose

connection

elbow

electrolux keyhole cooktop troubleshooting 13

Before Calling a Service Technician please check carefully

the operating instructions, service booklet and the warranty

terms and conditions

Troubleshooting

problem possible cause remedy

No ignition

Appliance power cord not plugged into power

socket or power switch is switched off.

Plug power cord in and switch power on.

Power failure Use match to light burner

Gas port(s) blocked in crown Clean burner crown

Burner cap or base incorrectly installed Re-t caps or base

Gas control not rotated to the ignition position Rotate gas control further or refer to instructions

Gas mains supply tap is off or supply failure Turn on gas tap or contact gas supply authority.

Gas bottle is low or empty Change or rell bottle

Gas hose is kinked, bent or trapped Straighten gas hose

Air in the gas supply hose Repeat ignition operation 2 -3 times

Knob is not depressed with sufcient force Press the knob down harder

Control knob is released too soon Hold knob down longer

Spark plug is wet or is dirty Switch off power and clean or dry the spark plug

Internal fault with ignition Contact Electrolux customer care

Burner lights but goes

out as soon as control is

released

Knob is not depressed with sufcient force Press the knob down harder

Control knob is released too soon Hold knob down longer

Gas port(s) blocked in crown Clean burner crown

Water on the ame sensor Switch off gas and power and then clean or dry the

ame sensor

Burner ame not adjusted correctly Contact Electrolux customer care

Noisy ignition

Burner cap or base incorrectly installed Re-t caps or base

Incorrect installation of burner cap Correct installation

Burner cuts off when

using it

Flame sensor is dirty Switch off gas and power and then clean or dry the

ame sensor

Flame sensor may be faulty Contact Electrolux customer care

Yellow ame

Burner aeration adjustment incorrect Contact Electrolux customer care

Burner cap or base incorrectly installed Re-t caps or base

Gas port(s) blocked in crown Clean burner crown

Gas smell

Gas hose or connection at bottle leaking Turn gas off at bottle or mains and contact Electrolux

customer care

Gas hose damaged or cracked Turn gas off at bottle or mains and contact Electrolux

customer care

Appliance has internal gas leak Turn gas off at bottle or mains and contact Electrolux

customer care

The induction unit cannot

be switched on or is not

operating

More than 10 seconds have passed since the

appliance was switched on

Switch the appliance on again.

The lock is switched on “L” Switch off the lock function or refer to instructions

Supply cord not plugged in or power is off Plug power cord in and switch power on.

Several sensor elds were touched at the

same time

Only touch one sensor eld

Automatic switch off has been triggered Remove any objects (pan, cloths, etc.) that are lying

on the control panel. Switch the appliance on again.

14 trouble shooting electrolux keyhole cooktop

Troubleshooting continued

problem possible cause remedy

Repeated acoustic

signal (4x), appliance

switches off

One or more sensor elds have been covered for

longer than 10 seconds

Uncover sensor eld

Repeated acoustic

signal (3x)

Timer function has reached zero “0” Touch any sensor

“F” appears in display

when power level

function is set

No pan on the cooking zone Place pan on the cooking zone

Unsuitable pan Use suitable pan

“E:11 or E:12” appears

in display

Power supply problem ( too high or low) Try again later

“E:01to E:10” appears

in display

Internal appliance fault Contact Electrolux customer care

electrolux keyhole cooktop technical specications 15

Technical Specications

Domestic built-in gas & induction appliance

Weight Gross: 12.9kg Net: 10.9kg

Product dimension (mm) See diagram below

Cut out dimension (mm) 738.5 (W) × Ø352 and 304.5 (D)

Package dimension (mm) 810 (W) × 427 (D) ×194 (H)

Gas inlet Φ9.5mm Hose or G1/2" Pipe

Gas Safety device Flame safeguard system

Ignition Electronic ignition mains powered

Power supply requirements 220-230V AC 10amp

Service cord length 1500mm

Induction Power 2200W maximum

Top plate Stainless steel bowls & ceramic glass

Trivet Cast main trivet Cast auxiliary trivet

Accessories Instruction book, inspection certicate, warranty & service guide, installation

template, elbow, elbow sealing washer and 2 rubber hose clamps

IND UCT ION

374mm

326mm

116mm

74mm

1500 mm

734mm

760mm

Electrolux EQ98X User manual

Related papers

Other documents