John Lewis JLWM1407 User manual

Brand: John Lewis

Model: JLWM1407

Category: Washing machines

Type: User manual

JLWM 1407

1400 spin washing machine

Instruction manual

Safety information

It is most important that this instruction book should be retained with

the appliance for future reference. Should the appliance be sold or

transferred to another owner, or should you move house and leave the

appliance, always ensure that the book is supplied with the appliance in

order that the new owner can get to know the functioning of the

appliance and the relevant warnings.

These warnings have been provided in the interest of safety. You MUST

read them carefully before installing or using the appliance. If you are

unsure of the meanings of these warnings contact the John Lewis

branch from which you purchased the appliance.

Important! Read carefully and keep for

future reference.

• The safety of your appliance complies

with the industry standards and with legal

requirements on the safety of appliances.

However, as manufacturers, we feel it is

our duty to provide the following safety

notes.

• It is most important that this instruction

book should be retained with the

appliance for future reference. Should the

appliance be sold or transferred to

another owner, or should you move

house and leave the appliance, always

ensure that the book is supplied with the

appliance in order that the new owner

can get to know the functioning of the

appliance and the relevant warnings.

• You MUST read them carefully before

installing or using the appliance.

• Before first starting up, check the

appliance for any damage incurred during

transport. Never connect up a damaged

appliance . If parts are damaged, contact

your supplier.

• If the appliance is delivered in the winter

months when there are minus

temperatures. Store it at room

temperature for 24 hours before using for

the first time.

General safety

• It is dangerous to alter the specifications

or attempt to modify this product in any

way.

• During high temperature wash

programmes the door glass may get hot.

Do not touch it!

• Make sure that small children and animals

do not climb into the drum. To avoid this,

please check into the drum before using.

• Any objects such as coins, safety pins,

nails, screws, stones or any other hard,

sharp material can cause extensive

damage and must not be placed into the

machine.

• Only use the advised quantities of fabric

softener and detergent. Damage to the

fabric can ensue if you over-fill. Refer to

the manufacturer’s recommendations of

quantities.

• Wash small items such as socks, laces,

washable belts etc in a washing bag or

pillow case as it is possible for such items

to slip down between the tub and the

inner drum.

• Do not use your washing machine to

wash articles with whalebones, material

without hems or torn material.

• Always unplug the appliance and turn off

the water supply after use and during

cleaning and maintenance.

• Under no circumstances should you

attempt to repair the machine yourself.

Repairs carried out by inexperienced

people may cause injury or serious

malfunctioning. Contact your local Service

Centre. Always insist on genuine spare

parts.

Installation

• This appliance is heavy. Care should be

taken when moving it.

• When unpacking the appliance, check that

it is not damaged. If in doubt, do not use it

and contact the Service Centre.

• All packing and transit bolts must be

removed before use. Serious damage can

occur to the product and to property if

this is not adhered to. See relevant

section in the user manual.

• After having installed the appliance, check

that it is not standing on the inlet and

drain hose and the worktop is not

pressing the electrical supply cable against

the wall.

• If the machine is situated on a carpeted

floor, please adjust the feet in order to

allow air to circulate freely under the

appliance.

• Always be sure, that there is no water

leakage from hoses and their connections

after the installation.

• If the appliance is installed in a location

subject to frost, please read the “dangers

of freezing” chapter.

• Any plumbing work required to install this

appliance should be carried out by a

qualified plumber or competent person.

• Any electrical work required to install this

appliance should be carried out by a

qualified electrician or competent person.

Use

• This appliance is designed for domestic

use. It must not be used for purposes

other than those for which it was

designed.

• Only wash and dry fabrics which are

designed to be machine washed or dried.

Follow the instructions on each garment

label

• Do not overload the appliance. See the

Washing Programme Table.

• Before washing, ensure that all pockets

are empty and buttons and zips are

fastened. Avoid washing frayed or torn

articles and treat stains such as paint, ink,

rust, and grass before washing.

Underwired bras must NOT be machine

washed.

• Garments which have been in contact

with volatile petroleum products should

not be machine washed. If volatile

cleaning fluids are used, care should be

taken to ensure that the fluid is removed

from the garment before placing in the

machine.

• As some duvets and eiderdowns should

be washed/dried in large commercial

machines because of their bulk, please

check with the manufacturer of the item

before washing in a domestic machine.

• The users should always check that they

have not left their gas lighters (disposable

or otherwise) in their clothing.

• Never tumble dry items that have had

contact with chemicals such as dry

cleaning fluid. These are of a volatile

nature and could cause an explosion.

Only tumble dry items which have been

washed in water or require airing.

• Plastic detergent dispensers should not

remain in the drum during the drying

cycle, as the plastic used is not designed

to withstand the heat. If you wish to

wash-through-to-dry you should use the

conventional detergent dispenser drawer.

• Never pull the power supply cable to

remove the plug from the socket; always

take hold of the plug itself.

• Never use your new appliance if the

power supply cable, the control panel, the

working surface or the base are damaged

so that the inside of the appliance is

accessible.

Child safety

• This appliance is not intended for use by

person (including children) with reduced

physical sensory or mental capabilities or

lack of experience and knowledge unless

they have been given supervision or

instruction concerning use of the

appliance by a person responsible for

their safety.

• The packaging components (e.g. plastic

film, polystyrene) can be dangerous to

children - danger of suffocation! Keep

them out of children’s reach.

• Keep all detergents in a safe place out of

children’s reach.

• Make sure that children or pets do not

climb into the drum. To prevent children

and pets becoming trapped inside the

drum the machine incorporates a special

feature. To activate this device, rotate the

button (without pressing it) inside the

door clockwise until the groove is

horizontal. If necessary use a coin.

To disable this device and restore the

possibility of closing the door, rotate the

button counterclockwise until the groove

is vertical.

Contents

Operating instructions

Safety information

General safety 2

Installation 3

Use 3

Child safety 4

Product description

Detergent dispenser drawer 8

Control panel

Programme Dial (2) 9

Spin (3) 9

Prewash (4) 9

Intensive (5) 10

Extra Rinse (6) 10

Quick (7) 10

Start Pause (8) 10

Door lock light (9) 10

Delay Start (10) 10

Display (11)

First use

Personalisation

Acoustic signals 12

Child lock 12

Daily use

Load the laundry 12

Measure out the detergent 12

Select the required programme 13

Select the spin speed or None option 13

Select the desired options 13

Select the delay start 14

Start the programme 14

How to change an option or a programme

during its cycle 14

How to interrupt a programme 15

How to open the door during the cycle of a

programme 15

Installation instructions

Installation

Unpacking 28

Positioning and levelling 29

Plumbing in 29

Water inlet 30

Water drainage 30

Special conditions 32

In the interest of the environment 32

Electrical connection 33

What to do if…

Repairs - After Sales Service

Environment concerns

Packaging materials 39

Ecological hints 39

Guide to use the

instruction manual

The following symbols will be found in the

text to guide you throughout the instructions:

Safety instructions

Hints and tips

Environmental information

End of programme 15

Helpful hints and tips

Washing programmes

Technical data

Consumption values

Care and cleaning

Descaling 22

External cleaning 23

Washing drum 24

Door seal 24

Cleaning the pump 24

Product description

1 Detergent dispenser drawer

2 Control panel

3 Door opening handle

4 Rating plate

5 Drain pump

6 Adjustable feet

1 2

Detergent dispenser drawer

Compartment for detergent used for

prewash and soak phase or for stain remover

used during the stain action phase (if

available). The prewash and soak detergent is

added at the beginning of the wash

programme. The stain remover is added

during the stain action phase.

Compartment for powder or liquid

detergent used for main wash. If using liquid

detergent pour it just before starting the

programme.

Compartment for liquid additives (fabric

softener, starch).

Follow the product manufacturer’s

recommendations on quantities to use and

do not exceed the «MAX» mark in the

detergent dispenser drawer. Any fabric

softener or starching additives must be

poured into the compartment before starting

the wash programme.

Control panel

Below is a picture of the control

panel. It shows the programme

selector dial as well as the buttons

and pilot lights. These are presented

by relevant numbers on the following

pages.

123456789

1011

Detergent dispenser drawer

Programme selector dial

Spin button

Prewash button

Intensive button

Extra rinse button

Quick button

Start/Pause button

Door lock light

Delay start button

Display - Wash time

Programme Dial (2)

It allows you to switch the appliance on/off

and/or to select a programme.

Spin (3)

By pressing this button you can change the

spin speed of the selected programme or to

select the available function (s).

None

By selecting this function all the spinning

phases are cancelled and the last rinse water

is drained. If you set this option with

programmes for cotton, synthetics and

delicates, the machine will perform some

extra rinses.

Prewash (4)

By pressing this button repeatedly, you can

select only one of the following options:

Prewash: the machine performs a prewash

cycle before the main wash phase. The

washing time will be prolonged. This option

is recommended for heavily soiled laundry.

The prewash ends with a short spin in

programmes for cotton and synthetic

fabrics, whereas in the programme for

delicate fabrics the water is only drained.

Stain: the machine adds a stain phase to the

washing of heavily soiled laundry. The

washing time will be prolonged by a few

minutes.

Pour a stain removing detergent into

the compartment marked

This function is available with a temperature

of 40° or higher.

Rinse hold: the machine will not drain the

water of the last rinse, this will ensure the

minimum of creasing to laundry. Before

opening the door the water must be

drained.

Intensive (5)

By selecting this function the washing

intensity will be increased and the washing

time will be prolonged by a few minutes

depending on the selected temperature.

This option can be selected for heavily soiled

cottons.

Extra Rinse (6)

This appliance is designed to save energy. If

it necessary to rinse the laundry using an

extra quantity of water (extra rinse), select

this option. Some additional rinses will be

performed. This option is recommended for

people who are allergic to detergents, and in

areas where the water is very soft.

Quick (7)

This option can be used for lightly soiled

laundry. The washing time will be reduced

according to type of fabric and the selected

temperature.

Start Pause (8)

This button allows you to start or to

interrupt the selected programme.

Door lock light (9)

The light Door lock shows if you can open

the door:

• light on: the door cannot be opened. The

machine in working or has stopped with

water left in the tub.

• light off: the door can be opened. The

programme is finished or the water has

been emptied out.

Delay Start (10)

The programme can be delayed from 30 min

- 60 min - 90 min, 2 hours and then by 1

hour up to a maximum of 20 hours by

means of this button.

Display (11)

11.1 11.2

The following pieces of information are

shown on the display:

11.1 - Child lock symbol.

11.2

•

Duration of washing programme in

hours and minutes, after you have

selected a programme. While the

programme is running (after you have

pressed the button 8), the displayed time

value decreases by one unit every minute.

The washing machine has stopped

with water in the tub, at the end of

the «Soak» programme or if the «Rinse

hold» option has been set: this is indicated

by a flashing zero. The «Door lock» pilot

light is still on. The door cannot be

opened.

The washing machine has

completed the programme: this is

indicated by a flashing zero. The «Door

lock» pilot light has gone off. It is now

possible to open the door.

•

Delay start, a time value indicated in

hours and selected by the relevant button.

The delay time (20 hours max) is

displayed for a few seconds, then the

duration of the selected programme

reappears. After you have pressed the

button 8, the countdown is updated every

hour, and, for the last hour, every minute.

•

An incorrect option selection has

been made: this is indicated by the

message Err for a few seconds when an

option incompatible with the current

programme is selected.

•

An alarm code indicates a fault with the

machine (see the relevant chapter).

First use

• Ensure that the electrical and

water connections comply with

the installation instructions.

• Remove the polystyrene block and

any material from the drum.

• Pour 2 litres of water into the main

wash compartment

of the

detergent drawer in order to

activate the ECO valve. Then run

a cotton cycle at the highest

temperature without any laundry

in the machine, to remove any

manufacturing residue from the

drum and tub. Pour 1/2 a measure

of detergent into the main wash

compartment and start the

machine.

Personalisation

Acoustic signals

The machine is provided with an acoustic

device, which sounds in the following cases:

• at the end of a washing cycle

• if there is a fault

You can deactivate the acoustic signal

(except if there is a fault) by pressing the

buttons 5 and the 6 simultaneously for

about 5 seconds. By pressing these buttons

again the acoustic signal is reactivated.

Child lock

This function works in two different ways:

• If enabled before the «Start/Pause»

button is pressed, it prevents the machine

from being started.

• If enabled after pressing the «Start/

Pause» button, it prevents any changes

being made to the programmes or

options selected

To enable or disable this function, press the

buttons 3 and 4 simultaneously for

approximately 6 seconds until the icon

appears on or disappears from the display.

Daily use

Load the laundry

Open the door by carefully pulling the door

handle outwards. Place the laundry in the

drum, one item at a time, shaking them out

as much as possible. Close the door.

Measure out the

detergent

Measure out the detergent and the

fabric softener

Pull out the dispenser drawer until it stops.

Measure out the amount of detergent

required, pour it into the main wash

compartment

or in the appropriate

compartment if it is required by the selected

programme or option (see more details in

«Detergent dispenser drawer» ).

If required, pour fabric softener into the

compartment marked

(the amount used

must not exceed the «MAX» mark in the

drawer). Close the drawer gently.

Select the required

programme

Turn the programme dial to the required

programme. The washing machine will

automatically select the maximum spin value

provided for the programme you have

chosen and the display will show the

duration, calculated on the basis of the

maximum load for each type of fabric.

Pressing the corresponding buttons to

change those values. The green pilot light of

the button 8 starts flashing.

The dial can be turned either clockwise or

counterclockwise. Turn to position «Off» to

reset programme/Switching the machine off.

At the end of the programme the

selector dial must be turned to

position «Off» , to switch the machine

off.

Caution! If you turn the programme

selector dial to another programme

when the machine is working, the

red pilot light of button 8 will blink 3

times to indicate a wrong selection.

The machine will not perform the

new selected programme. The

message Err is displayed for a few

seconds. The machine will not

perform the new selected

programme.

Select the spin speed or

None option

Press button 3 repeatedly to select the

required spin speed or to select «None»

option. If you select this option, all spinning

phases are suppressed.

The relevant light will light up.

Select the desired

options

Press buttons 4,5,6 and 7 to select the

available options. Depending on the

programme, different options can be

selected together. These must be selected

after choosing the desired programme and

before pressing button 8.

If an option which is not compatible with the

set wash programme is selected, the red

button 8 light flashes 3 times and the

message Err is displayed for a few seconds.

When the option is set, the relevant light is

on.

Select the delay start

Before you start the programme, press this

button repeatedly to select the desired

delay. The set delay time value (up to 20

hours) will appear on the display for a few

seconds, then the duration of the

programme will appear again. The wash

programme can be delayed from 30 min - 60

min - 90 min, 2 hours and then by 1 hour up

to a maximum of 20 hours.

You can cancel the delay time at any

moment, before you press the «Start/

Pause» button.

Selecting the delayed start

You must select this option after you have

set the programme and before you press the

«Start/Pause» button.

• Select the programme and the required

options.

• Select the delay start.

•

Press button 8: the machine starts its

hourly count down. The programme will

start after the selected delay has expired.

Opening the door throughout the

delay time

If you wish to add laundry in the machine

during the delay time

•

Press button 8 to put the machine in

pause.

• Add the laundry, close the door

•

Press 8 button again.

Cancelling the delayed start

•

Press button 8.

• Press «Delay start» button once until the

symbol «0’» is displayed.

•

Press button 8 again.

The Delay Start cannot be selected with the

draining programme.

Start the programme

To start the selected programme, press the

button 8 ; the green pilot light stops flashing.

If you have selected a delay time, the

countdown will begin and will be shown on

the display.

To interrupt a programme which is running,

press button 8: the green pilot light starts to

flash. To restart the programme from the

point at which it was interrupted, press the

button 8 again. If an incorrect option is

selected, the red pilot light of button 8

flashes 3 times and the message Err is

displayed for a few seconds.

Important!

You must set the washing machine to Pause

before you make any change in the

programme in progress.

How to change an option

or a programme during

its cycle

It is possible to change some options

before the programme carries them out.

Before you make any change, you must

pause the washing machine by pressing the

button 8. Changing a running programme is

possible only by resetting it.

Turn the programme selector dial to «Off»

and then to the new programme position.

Start the new programme by pressing the

button 8. The washing water in the tub will

not empty out

How to interrupt a

programme

Press the button 8 to interrupt a

programme which is running, the

corresponding green pilot light starts

blinking.

Press the same button again to restart the

programme.

How to open the door

during the cycle of a

programme

You can open the door, after having set the

washing machine to Pause, provided the

following conditions exist:

• The washing machine is not in the heating

phase

• The level of the water is not high;

If these requirements are met, when you

pause the washing machine, the «Door

lock» light goes off and the door can be

opened.

Should it not be possible to open the door,

and should it be absolutely necessary to do

so, switch the machine off by turning the

selector dial to Off. After a few minutes,

you can open the door.

Pay attention to the level and

temperature of the water in the

washing machine! When you close the

door to restart the programme turn the dial

to the previous programme and repeat the

options previously selected and press button

End of programme

At the end of the programme, the washing

machine stops automatically, the button 8

light and the Door lock light go off. The

display shows a flashing zero «0». It is

possible to open the door.

If you had selected an option that ends with

water left in the tub the Door lock light

remains lit to indicate that the water must

be drained before opening the door.

To drain or to spin follow the below

instructions:

1. Turn the programme selector dial to

Off.

2. Select the draining or spinning

programme.

3. Reduce the spin speed if needed, by

pressing the relevant button.

Press button 8.

At the end of the programme, the door can

be now opened. Turn the programme

selector dial to Off to switch the machine

off.

Remove the laundry from the drum. Check

whether the drum is completely empty, by

rotating it with your hand. The purpose of

this is to prevent any items of laundry from

remaining accidentally in the drum, where

they might get damaged in a subsequent

wash (e.g. by shrinking) or bleed colour into

another load of laundry.

If you do not intend to carry out another

wash, close the water tap. Leave the door

open to prevent the formation of mildew

and unpleasant smells.

Stand by: once the programme has

finished after a few minutes the

energy saving system is enabled with

the pilot lights switched on. By

pressing any button the appliance will

come out of the energy saving status.

Helpful hints and tips

Sorting out the laundry

Follow the wash code symbols on each

garment label and the manufacturer’s

washing instructions. Sort the laundry as

follows: whites, coloureds, synthetics,

delicates, woollens.

Before loading the

laundry

Never wash whites and coloureds together.

Whites may lose their «whiteness» in the

wash.

New coloured items may run in the first

wash; they should therefore be washed

separately the first time.

Make sure that no metal objects are

left in the laundry (e.g. hair clips,

safety pins, pins).

Button up pillowcases, close zip fasteners,

hooks and poppers. Tie any belts or long

tapes.

Remove persistent stains before washing.

Rub particularly soiled areas with a special

detergent or detergent paste.

Treat curtains with special care. Remove

hooks or tie them up in a bag or net.

Removing stains

Stubborn stains may not be removed by just

water and detergent. It is therefore advisable

to treat them prior to washing.

Blood: treat fresh stains with cold water.

For dried stains, soak overnight in water

with a special detergent then rub in the soap

and water.

Oil based paint: moisten with benzine

stain remover, lay the garment on a soft

cloth and dab the stain; treat several times.

Dried grease stains: moisten with

turpentine, lay the garment on a soft surface

and dab the stain with your fingertips and a

cotton cloth.

Rust: oxalic acid dissolved in hot water or a

rust removing product used cold. Be careful

with rust stains which are not recent since

the cellulose structure will already have been

damaged and the fabric tends to hole.

Mould stains: treat with bleach, rinse well

(whites and fast coloureds only).

Grass: soap lightly and treat with bleach

(whites and fast coloureds only).

Ball point pen and glue: moisten with

acetone

, lay the garment on a soft cloth

and dab the stain.

1) do not use acetone on artificial silk

Lipstick: moisten with acetone as above,

then treat stains with methylated spirits.

Treat any residual marks with bleach.

Red wine: soak in water and detergent,

rinse and treat with acetic or citric acid, then

rinse. Treat any residual marks with bleach.

Ink: depending on the type of ink, moisten

the fabric first with acetone

, then with

acetic acid; treat any residual marks on white

fabrics with bleach and then rinse

thoroughly.

Tar stains: first treat with stain remover,

methylated spirits or benzine, then rub with

detergent paste.

Detergents and additives

Good washing results also depend on the

choice of detergent and use of the correct

quantities to avoid waste and protect the

environment.

Although biodegradable, detergents contain

substances which, in large quantities, can

upset the delicate balance of nature.

The choice of detergent will depend on the

type of fabric (delicates, woollens, cottons,

etc.), the colour, washing temperature and

degree of soiling.

All commonly available washing machine

detergents may be used in this appliance:

• powder detergents for all types of fabric

• powder detergents for delicate fabrics

(60°C max) and woollens

• liquid detergents, preferably for low

temperature wash programmes (60°C

max) for all types of fabric, or special for

woollens only.

The detergent and any additives must be

placed in the appropriate compartments of

the dispenser drawer before starting the

wash programme.

If using liquid detergents, a programme

without prewash must be selected.

Your appliance incorporates a recirculation

system which allows an optimal use of the

concentrated detergent.

Follow the product manufacturer’s

recommendations on quantities to use and

do not exceed the «MAX» mark in

the detergent dispenser drawer.

Quantity of detergent to

be used

The type and quantity of detergent will

depend on the type of fabric, load size,

degree of soiling and hardness of the water

used.

Follow the product manufacturers’

instructions on quantities to use.

Use less detergent if:

• you are washing a small load

• the laundry is lightly soiled

• large amounts of foam form during

washing.

Degrees of water

hardness

Water hardness is classified in so-called

“degrees” of hardness. Information on

hardness of the water in your area can be

obtained from the relevant water supply

company, or from your local authority. If the

water hardness degree is medium or high

we suggest you to add a water softener

following always the manufacturer’s

instructions. When the degree of hardness is

soft, readjust the quantity of the detergent.

Washing programmes

Programme - Maximum and Minimum

Temperature - Cycle Description - Maximum

Spin Speed - Maximum Fabrics Load - Type of

Laundry

Options

Detergent

Compartment

Cottons

90° - 60°

Main wash - Rinses

Maximum spin speed at 1400 rpm

Max. load 7 kg - Reduced load 3 kg

White cotton (heavily or normally soiled items).

SPIN

NONE

RINSE HOLD

PREWASH

INTENSIVE

STAIN

QUICK

EXTRA RINSE

Cottons Economy

60°

Main wash - Rinses

Maximum spin speed at 1400 rpm

Max. load 7 kg

White or fast colour cotton (normally or slightly

soiled items).

Energy saving programme: This programme can be

selected for slightly or normally soiled cotton items.

The temperature will decrease and the washing time

will be extended. This allows to obtain a good washing

efficiency by saving energy.

SPIN

NONE

RINSE HOLD

PREWASH

STAIN

EXTRA RINSE

Cottons Economy

40°

Main wash - Rinses

Maximum spin speed at 1400 rpm

Max. load 7 kg

White or non fast colour cotton (slightly soiled

items).

This programme can be selected for slightly or

normally soiled cotton items. The temperature will

decrease and the washing time will be extended. This

allows to obtain a good washing efficiency by saving

energy.

SPIN

NONE

RINSE HOLD

PREWASH

STAIN

EXTRA RINSE

Programme - Maximum and Minimum

Temperature - Cycle Description - Maximum

Spin Speed - Maximum Fabrics Load - Type of

Laundry

Options

Detergent

Compartment

Cottons

40° - 30°

Main wash - Rinses

Maximum spin speed at 1400 rpm

Max. load 7 kg - Reduced load 3 kg

Colour cotton (normally or slightly soiled items).

SPIN

NONE

RINSE HOLD

PREWASH

INTENSIVE

STAIN

QUICK

EXTRA RINSE

Synthetics

60° - 40° - 30°

Main wash - Rinses

Maximum spin speed at 900 rpm

Max. load 3.5 kg - Reduced load 2 kg

Synthetic or mixed fabrics: underwear, coloured

garments, non-shrink shirts, blouses.

SPIN

NONE

RINSE HOLD

PREWASH

STAIN

QUICK

EXTRA RINSE

Synthetics Economy

40°

Main wash - Rinses

Maximum spin speed at 900 rpm

Max. load 3.5 kg - Reduced load 2 kg

Mixed fabrics,shirts, blouses, underwear, coloured

garments, non-shrink shirts.

SPIN

NONE

RINSE HOLD

PREWASH

STAIN

EXTRA RINSE

Delicates

40° - 30°

Main wash - Rinses

Maximum spin speed 700 rpm

Max. load kg 3.5 - Reduced load kg 2

Delicate fabrics: acrylics, viscose, polyester.

SPIN

NONE

RINSE HOLD

PREWASH

STAIN

QUICK

EXTRA RINSE

Wool - Hand wash

40° - 30° - Cold

Main wash - Rinses

Maximum spin speed at 900

Max. load 2 kg

Washing programme for machine washable wool as

well as for hand washable woollens and delicate

fabrics. Note: A single or bulky item may cause

imbalance. If the appliance doesn’t perform the final

spin phase, add more items, redistribute the load

manually and then select the spinning programme.

SPIN

NONE

RINSE HOLD

Programme - Maximum and Minimum

Temperature - Cycle Description - Maximum

Spin Speed - Maximum Fabrics Load - Type of

Laundry

Options

Detergent

Compartment

Soak

30°

Prewash - Soak for about 40 minutes - Stop with

water in the tub

Max. load 7 kg

Special programme for heavily soiled laundry. The

machine performs a soak at 30°C. At the end of this

time the machine will stop automatically with water

left in the tub. Before starting a new washing phase, it

is necessary to empty out the water by:

•

Draining only: turn the programme selector dial

to the draining programme (press then the button

8).

•

Draining and spinning: turn the programme

selector dial to spinning programme, reduce the

spin speed by pressing the relevant button, press

then button 8.

Important! This programme cannot be used for very

delicate fabrics as silk or wool. Pour the detergent for

the soak programme into the compartment marked .

At the end of the soak (after having emptied out the

water) you can select the washing programme. (First

turn the programme selector dial to Off, then to the

programme and press the button 8).

Rinse

Rinses

Maximum spin speed at 1400 rpm

Max. load 7 kg

With this programme it is possible to rinse and spin

cotton garments which have been washed by hand.

The machine performs a few rinses, followed by a final

long spin. The spin speed can be reduced.

SPIN

NONE

RINSE HOLD

EXTRA RINSE

Drain

Draining of water

Max. load 7 kg

For emptying out the water of the last rinse in

programmes with the set option, which ends with

water left in the tub.

Page is loading ...

John Lewis JLWM1407 User manual

Brand: John Lewis

Model: JLWM1407

Category: Washing machines

Type: User manual

Download PDF

report

John Lewis JLWM1407 User manual

John Lewis JLWM1407 User manual

Related papers