Whirlpool ACM 709/BA User guide

Brand: Whirlpool

Model: ACM 709/BA

Category: Hobs

Type: User guide

This manual contains important information regarding

safety, the use and maintenance of your new hob. Read the

manual carefully and keep it in an easily accessible place for

future consultation.

Precautions and Advice

1. CAUTION: This cooktop complies with all

applicable safety and electromagnetic

compatibility legislation.

However, individuals fitted with a heart pacemaker

should maintain a safe distance from the appliance.

This is because it is not possible to guarantee that all

pacemakers on the market comply with the standards

in compliance with which this appliance was tested so

it is not possible to provide an absolute guarantee of

the absence of potentially harmful interference.

2. Disposal of packaging materials: dispose of the various

packing materials responsibly, in full compliance with

local authority regulations governing waste disposal.

3. This induction hob is designed solely for use as a

domestic appliance. No other type of use is permitted.

The manufacturer declines all responsibility for

inappropriate use.

4. The appliance is not intended for use by persons

(children included) with physical, sensory or mental

impairment or without experience and knowledge of

the appliance, unless supervised or previously

instructed in its use by those responsible for their

safety.

5. The cooking zones become extremely hot during use:

be careful and keep children away from the appliance

to avoid the risk of scalding or burns.

6. The letter “H” will appear on the control

panel display to indicate “residual heat” in the

corresponding cooking zone: the temperature

of the cooking zone is above 60 °C: do not

touch the cooking zone or

place any object on it while the letter “H” remains lit.

7. If the surface of the hob should become damaged

(cracked or broken glass), do not use the appliance

and call the After-sales Service immediately.

8. Any repairs or work on the appliance must be carried

out by a qualified technician.

9. This hob is equipped with a thermoprotector to

prevent the risk of its internal circuits being damaged

by high temperatures from external heat sources

(e.g. an undercounter oven). If the temperature of the

electronic circuits exceeds the safety threshold, the

thermoprotector activates, automatically switching off

the hob. The display shows an error message

(see. section “Troubleshooting Guide”). When the

temperature returns to within normal levels the hob is

able to be switched on again.

10. Make sure the cooking zones and the bottoms of pots

are dry before use.

11. Do not place metal objects such as kitchen utensils

(knives, forks, spoons, …), lids or other similar items

on the cooking zones as they can become very hot.

12. Be extremely vigilant when cooking food with boiling

oil or fat since these can catch fire. In the event of oil

catching fire, never attempt to put it out with water:

switch the hob off and cover the pot immediately with

a lid; leave the pot on the cooking zone to cool down.

Dispose of the oil in compliance with current

regulations.

13. When you finish cooking, press button .

Before use

Important: The induction cooking zones

will not switch on if pots and pans are not of

the correct dimensions.

Only use pots bearing the symbol

“INDUCTION SYSTEM” (See figure

opposite).

Before switching the hob on, position the pot on the

desired cooking zone.

Existing pots and pans:

Use a magnet to check whether pots or pans are suitable

for use on the induction hob: pots are unsuitable if they

cannot be magnetically detected.

1. Ensure pots have a smooth bottom, otherwise they

may scratch the hob's glass ceramic surface. Check

dishes.

2. Do not use empty pots on the hob, especially

enamelled or aluminium ones. This could result in

damage to both the glass ceramic surface and the

bottom of the pots.

3. Never place hot pots or pans on the hob's control

panel. This could result in damage.

Recommended diameters of pot bottoms

IMPORTANT SAFETY INFORMATION

OK NO

26 cm

17 cm 26 cm

21 cm

14 cm 21 cm

18 cm

14.5 cm

12 cm 18 cm

9 cm 14.5 cm

Installation must be carried out by a qualified electrician

who is fully aware of current safety and installation

regulations. The manufacturer declines all liability for injury

to persons or animals and for damage to property resulting

from failure to observe the regulations provided in this

chapter.

Electrical connections

• Hob electrical connection must be made before

connecting the appliance to the electricity supply.

• Electrical connection must be carried out in compliance

with the regulations of the local electric utility company.

• Make sure that the voltage indicated on the rating plate

on the underside of the appliance corresponds to the

domestic power supply voltage.

• Regulations require that the appliance is earthed: use

conductors (including the earth conductor) of the

appropriate size only.

• For electrical connection, use an H05 RR-F type cable as

specified in the table “Power supply voltage”.

The power supply cable must be long enough

to allow the hob to be removed from the

worktop and must be positioned so as to avoid

damage or overheating caused by contact with

the base of the hob itself. Do not use extension leads.

Power supply voltage

If the hob already has a power cable, follow the

instructions given on the label attached to the

cable.

Connect the appliance to the electricity supply by

means of an all-pole disconnect switch with minimum

contact gap of 3 mm.

Connecting to the terminal board

Connect the yellow/green earth wire to the terminal with

the symbol . This wire must be longer than the other

wires.

1. Remove the terminal block cover (A), undoing the

screw and inserting the cover in the terminal block

hinge (B).

2. Strip approx. 70 mm of sheath from the power supply

cable.

3. Strip approx. 10 mm of sheath from the wires. Insert

the power supply cable into the cable clamp and

connect the wires to the terminal board as indicated in

the diagram next to the terminal board itself.

4. Secure the power cable with the cable clamp.

5. Close the cover (C) and screw it on the terminal block

with the removed screw - point (1).

Each time the cooktop is connected to the mains it

carries out an automatic check which lasts several

seconds.

INSTALLATION and ELECTRICAL CONNECTION

Wires Amount x size

230V ~ +

3 X 4 mm

230-240V ~ +

3 X 4 mm

(Australia only)

230V 3 ~ +

4 X 1.5 mm

400V 3N ~ +

5 X 1.5 mm

400V 2N ~ +

4 x 1.5 mm

230V

400V 3N ~ 230V ~

230-240V~FOR AU ONLY

230V~FOR UK ONLY

400V 2N ~

230V 3~

ONLY FOR BELGIUM

400V 2N~

FOR NL ONLY

Installation and fixing

The installer is responsible for any damage or

injury resulting from incorrect installation.

To guarantee correct operation, the appliance

must be installed on a perfectly flat surface.

The worktop must be 20-50 mm thick.

If necessary, cut the kitchen unit and worktop to fit before

installing the hob. Clean the cutout of any chips that could

compromise appliance operation.

For cut-out dimensions, see the figure below.

For flush mounted installation or setting

into a marble worktop, contact the After-sales

Service for the installation kit and necessary

instructions.

• 4812 310 19277 Installation kit for marble

worktop.

• 4801 211 00112 Installation kit for flush fitted

worktop.

To guarantee correct operation, the appliance must be

installed on a perfectly flat surface.

The worktop must be 20-50 mm thick.

If necessary, cut the kitchen unit and worktop to fit before

installing the hob. Clean the cutout of any remaining dust

that could compromise appliance operation.

For the distance between the underside of the induction

hob and the kitchen unit (or separating panel), observe the

dimensions given in the figure at the side. If a column unit

is installed adjacent to the hob, leave a distance of at least

100 mm from the edge of the hob.

Assembly

1. Position the clips (A) in the spaces provided on the

hob trim (fig. 3) if not already positioned.

2. Measure the centre point of the vertical sides of the

cut-out (fig. 1)

3. Fit the brackets (C) in the centre of the vertical sides,

aligning the upper edge of the brackets so that they are

flush with the worktop surface (fig. 2).

4. Fix the brackets with the 4 screws supplied (B) using

the holes provided.

5. Insert the hob in the cutout, making sure the clips (A)

are secured in the spaces provided (fig. 4).

490

580

510

483

553

min. 50

770

483

510

742

R min. 6.5

max. 8

min. 50

560

490

R min. 6.5

max. 8

Dimensions

in mm

750

min.

min. 20

min. 5

fig. 2

fig. 1

Undercounter oven installation:

• If an oven (which must be of our manufacture) is to be

installed under the hob, ensure it is equipped with a

cooling system and observe the distances given in the

figure to the side.

• There must be nothing between the cooktop and the

oven (cross rails, panels, brackets, etc.).

Control panel

Switching the hob ON/OFF

To switch the hob on, press the button for approx.

2 seconds until the cooking zone displays light up. To

switch off, press the same button until the displays switch

off. All the cooking zones are switched off.

If the hob has been in use, the residual heat indicator “H”

remains lit until the cooking zones have cooled down.

The hob automatically switches off if no function

is selected within 10 seconds of switching on.

fig. 4

fig. 3

5mm

OPERATING INSTRUCTIONS

Child safety

Cooking zone controls and corresponding display

On/Off

Timer

the symbols are not

active! To select the

desired functions,

touch the

areas below.

Switching on and adjusting cooking zones

After switching on the hob and positioning the pot on the

chosen cooking zone, adjust the heat setting using the

button +. When switched on, the display shows level 5.

Each cooking zone has different heat settings that can be

adjusted using the buttons +/-, which go from “1”: min.

heat setting to “9”: max. heat setting. Some cooking zones

have a fast boil function (Booster), shown on the display

with the letter “P”.

Fast boil function (Booster)

This function, only present on some cooking zones, makes

it possible to exploit the hob's maximum power (for

example to bring water to the boil very quickly). To select

this function, press the button “+” until “P” appears on the

display or, after switching the hob on, press the “-” button

for the selected cooking zone. In this case too, “P” appears

on the display. After 10 minutes' use of the booster

function, the appliance automatically sets the zone to

level 9.

Switching off cooking zones

Select the cooking zone to be switched off by pressing the

“+” or “-” key (a dot lights up at the bottom right hand

side of the heat setting indicator).

Press the key “-” to set the level to “0”.

The cooking zone can also be switched off by pressing keys

“+” and “-” at the same time. The cooking zone switches

off and the residual heat indicator “H” lights up

Child safety

This function locks the hob controls to prevent accidental

switching on by children. To activate the child safety

function, switch on the hob then press and hold the

button for three seconds: an acoustic signal and a

luminous indicator under the key symbol signal activation.

The control panel is locked with the exception of the OFF

function. To unlock the controls, repeat the child safety

activation procedure. The illuminated dot switches off and

the hob is active again.

The presence of cleaning water, liquid spilled

from pots or any objects resting on the button

below the symbol can accidentally activate or

deactivate the child safety function.

Child guard accessory AMH 122

This accessory can be obtained from the After-sales

Service under Part N° 481931018436

Timer

The timer can be used to set a max.

cooking time of 99 minutes (1 hour and

39 minutes) for one cooking zone only.

Select the cooking zone to be used with

the timer (an illuminated dot appears to

the bottom right hand side of the heat setting indicator on

the display), then set the desired cooking time using the

buttons “+” and -“-” of the timer function (see figure

above). A few seconds after the button is pressed, the

timer begins the countdown (the luminous dot of the

selected cooking zone starts flashing). Once the set time

has elapsed, an acoustic signal sounds and the cooking zone

switches off automatically.

To deactivate the timer, press the button “-” until the

display shows “0:0” or press the buttons “+” and “-” of the

timer at the same time.

Important! The timer function can only be

used with one cooking zone at a time.

Minute minder

The minute minder can only be used when the hob is not

in use and allows a maximum setting of 99 min.

Press the button “+” below the timer indicators: the

display shows the minutes for setting.

Select the time desired using the buttons + and -.

After a few seconds the minute minder starts to count

down. Once the set time has elapsed an acoustic signal

sounds.

Important! The minute minder function can

only be used when the hob is switched off; if it is

then switched on, the minute minder countdown

is automatically cancelled.

Control panel warnings.

Residual heat indicator.

The hob is fitted with a residual heat indicator for

each cooking zone. These indicators alert the user

when cooking zones are still hot.

If the display shows , the cooking zone is still hot.

If the residual heat indicator of a given cooking zone is lit,

that zone can be used, for example, to keep a dish warm

or to melt butter.

When the cooking zone cools down, the display switches

off.

Incorrect or missing pot indicator.

The hob features an automatic pot detection

system for all cooking zones. If no pot is detected,

the display with the cooking zone power level

indicator flashes. Make sure the pot is correctly

positioned and that it has the characteristics given in the

section “Before use”.

Button -

Heat setting indicator

Selected cooking zone

indicator

Button +

Cooking zone

positioning

Care and maintenance

Clean the hob after each use in order to avoid damaging

the surface and to prevent the formation of baked-on

deposits which are difficult to remove. Before cleaning,

make sure the cooking zones are switched off and that the

residual heat indicator (“H”) is not displayed.

• Never clean the hob with a steam cleaner!

• Periodically check for dust under the

appliance, near the cooling air inlet or the

outlet openings. This could hinder the

ventilation and cooling of the electronic

module and decrease the effectiveness of the

hob.

To clean the hob, proceed as follows:

1. use a soft clean cloth, absorbent kitchen wipes or a

proprietary cleaner for glass ceramic hobs. Do not use

abrasive sponges and/or metal scouring pads.

2. Food spills should be cleaned off before they bake

onto the glass ceramic surface. Sugar and foods with a

high sugar content damage the glass ceramic surface

and must be immediately removed using a scraper for

glass. Caution! Glass scrapers have a very sharp blade

and must be handled with care.

3. Remove any stubborn food residues with a scraper or

proprietary detergents.

4. Salt, sugar and sand can scratch the glass ceramic hob:

clean up any such spills on the hob immediately.

Troubleshooting Guide

• Before contacting After-sales Service:

• read and follow the instructions given in the section

“Operating instructions”.

• Connect the hob to the electricity supply and check that

the supply has not been shut off.

• Clean the hob and dry it thoroughly.

• If, when the hob is switched on, alphanumeric codes

appear on the display, consult the following table for

instructions.

Important! If you are unable to turn the glass-ceramic hob off after using it, disconnect it immediately from the

power supply.

After-sales Service

Before contacting After-sales Service:

• Try to solve the problem (see “Troubleshooting

Guide”).

• Switch the appliance off, wait 30 seconds then switch it

on again. to see if the fault persists.

If after the above checks the fault persists, contact the

nearest After-sales Service.

Always provide:

• a brief description of the fault;

• the exact type and model;

• the service number (number after the word Service on

the rating plate) is located on the underside of the

cooktop or on the warranty booklet;

• your complete address and phone number.

If any repairs are required, please contact an authorized

After-sales Service as indicated in the warranty.

MAINTENANCE

ERROR CODE DESCRIPTION POSSIBLE CAUSES REMEDY

The hob switches off

and after 30 seconds

emits an acoustic signal

every 4 seconds

Continuous pressure on

control panel area

Water or utensils on control panel Clean the control panel

C81, C82

The control panel switches off

because of excessively high

temperatures

The internal temperature of

electronic parts is too high

Wait for the hob to cool down

before using it again

F42 or F43

The connection voltage is

wrong

The sensor detects a discrepancy

between the appliance voltage and

that of the mains supply

Disconnect the hob from the

mains and check the electrical

connection

F12, F21, F25, F36,

F37, F40, F47, F56,

F58, F60

Call the After-Sales Service and specify the error code

Failure to comply with these instructions may

compromise the safety and quality of the

product.

Appliance data plate

Energy saving tips

For optimum results, observe the following advice:

• Use pots and pans whose bottom diameter is equal to

that of the cooking zone.

• Only use flat-bottomed pots and pans.

• If possible, keep pot lids on when cooking.

• Cook vegetables, potatoes, etc. with little water in

order to cut down cooking time.

• Use a pressure cooker to to save even more energy and

time.

• Make sure you place the pot or pan in the centre of the

cooking zone outlined on the hob.

Safeguarding the environment

Packaging

The packaging material is 100% recyclable and marked

with the recycling symbol

Electrical Appliances

This appliance is marked in compliance with European

Directive 2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE). By ensuring that this appliance is

scrapped suitably, you can help prevent potentially

damaging consequences for the environment and health.

• The symbol on the appliance, or on documentation

enclosed with the appliance, indicates that this product

must not be treated as household waste, but must be

delivered to the nearest collection centre for the

recycling of electrical and electronic appliances. Disposal

must be carried out in accordance with local

environmental regulations for waste disposal. For further

information on the treatment, recovery and recycling of

this appliance, contact your competent local authority,

the collection service for household waste.

Declaration of Conformity

• This hob is suitable for contact with foodstuffs and

complies with EEC (CE) regulation n. 1935/2004.

• The appliances are designed solely for use as cooking

appliances. Any other use (e.g. for room heating) is

considered as improper use and potentially dangerous.

• The appliances are designed, built and sold in

compliance with:

• safety objectives of the “Low Voltage” Directive

2006/95/EC (which replaces 73/23/EEC and

subsequent amendments);

• Protection requirements of EMC Directive

2004/108/EC “Electromagnetic compatibility”;

• the requirements of Directive 93/68/EEC.

MODEL SERIALNUMBER

BRAND

USER ADVICE

Attach here one of the two appliance

data plate stickers found in the warranty booklet

Whirlpool ACM 709/BA User guide

Brand: Whirlpool

Model: ACM 709/BA

Category: Hobs

Type: User guide

Download PDF

report

Whirlpool ACM 709/BA User guide

Whirlpool ACM 709/BA User guide

Related papers

Other documents