2. Autopot
  3. 2 Pot XXL System

Autopot 2 Pot XXL System Operating instructions

  • Hello! I've reviewed the user manual for the AutoPot XXL 2Pot, XXL 2Pot 9, XXL 2Pot 13 watering system. This document contains important information about setting up and maintaining the system, including guidance on ensuring the AQUAvalve5 functions correctly. I'm ready to answer your questions about the device.
  • How do I ensure the AQUAvalve5 floods and drains correctly?
    How should I clean the AQUAvalve5?
    What should I do before turning on the system for the first time?
Your 2Pot XXL System
set-up guidelines 9
[email protected] I www.autopot-usa.com I +(1) 702-338-0373 [email protected] I www.autopot-usa.com I +(1) 702-338-0373
Simple care
guidelines
Ensuring that the AQUAvalve5 floods
and drains correctly
Care and maintenance
Making sure your AQUAvalve5 floods and
drains correctly is simply achieved and
only takes a few seconds.
Hold the AQUAvalve5 at eye level so that
you can see the silicone fitted to the top
float resting on the hole below it.
The silicone must create a tight seal when
touching the hole.
If it looks like it is not sitting parallel on the
hole below, simply lift the top float and
apply pressure to one side of the silicone,
drop the float and hold at eye level again.
Repeat the procedure if necessary.
It is also handy to have a paper clip or pipe
cleaner to hand so that you can push it
through the AQUAvalve5 nozzle, this will
remove any lime scale build up that may
have occurred during the growing season.
Blowing through the AQUAvalve5 nozzle
will also help to remove any build up. Do
not under any circumstances use a drill &
drill bit to clear the AQUAvalve5 nozzle.
This will potentially damage the
AQUAvalve5 beyond repair.
11
2
2
3
4
Ensure the silicone is sitting parallel
on the hole below it. Hold at eye level
to check the position is correct
13
2Pot XXL 13
(13 gal pot - excl.
adaptive collar)
2Pot XXL 9
(9 gal pot - incl.
adaptive collar )
plants
Allow your
to
establish
before turning your
system
on
.
At the end of your growing season, clean
the AQUAvalve5 using warm soapy water.
Using an old tooth brush will help.
The AQUAvalve5 is easily disassembled.
The top float will slide all the way across
and the bottom float is unclipped from its
pivoting position. The circular discs fitted to
the top float can also be removed by using
pliers to grip the raised point.
At this point is it advisable to remove the
silicones to avoid them being lost.
2Pot XXL setup instructions
Using your front instruction sheet, repeat the module set up instructions for the number of trays.
If you require any guidance email - [email protected]
Advice
Allow your plants to establish for 7-10 days before turning system on
Plan views
and options
Suggested layouts
• 1x12.4galreservoir&3/8”grommet
• 1xReservoirlid
• 2x1PotXXLtray,lid&3/8”grommet
• 2x1/4”blankinggrommet
• 2xXXLadaptivecollar(XXL9Only)
• 2x9galor13galfabricpot
• 1x3/8”GolfFilter
• 1x3/8”crossconnector
• 2xAQUAvalve5
• 6.6ftof3/8”pipe
• 2xrootcontrolPotSock
• 2x3/8”inlinetap
2Pot XXL System contents
Advice
• Pleasenotethatmultiplefabricpotsmayincreaseroomhumidityduetotheporosityoftheirexposedsurfaces.
• Potupyourplants,waterthrough,thenallowyourplantstoestablishinthepotsforaperiodof7to10daysbefore
turning your system on. This will encourage a stronger and healthier root system.
• Alwaysraiseyourreservoirtoaminimumof6”abovethehighestAQUAvalveandre-fillthereservoirwhenthereis
approximatelya1/3ofthesolutionleft-NEVERALLOWTHERESERVOIRTORUNEMPTY.
• WithAQUAvalve5systemsmineralororganicfertilisersmaybefedviathereservoirandpipework.Organicfertilisers
willrequireawaterpumpinthereservoirrunningfor15minsevery2hrsandcleaningofthereservoir,pump,and 
 filtereachtimethereservoirempties.Flushpipeworkwithplainwatereverytimethereservoirempties.
• CleanallsubstratefromthebottomandsidesofthepotsbeforeplacingintraystoensureAQUAvalvefunctionality.
• Alwaysusefreedrainingsubstrates,forexample:soil/perlite,coco/perlite,soil/claypebbles,coco/claypebbles,
rockwool/claypebbles.
13
1 2 Fit PotSock over the
base of fabric pot
Water through pot and
allow to drain outside
the tray. Brush off debris.
Fill fabric pot with grow
media and pot up plants.
Place fabric pot into the tray.
Make sure it is CLEAN!
Place lid over AQUAvalve
compartment on the tray.
Connect your 3/8” pipe
to the relevant fitting
3/8"crossconnector
3/8"pipe
3/8"to
p
hat
g
rommet
3/8"golffilter
3/8"inlinetap
AQUAvalve5
12.4gal
reservoir
1/4"blankinggrommet
[email protected] I www.autopot-usa.com I +(1) 702-338-0373
Pull
6Remove AQUAvalve collar
Push 3/8” pipe through
collar and attach to
AQUAvalve nozzle
Rescrew collar - DON’T
overturn... when you
feel it grip STOP
Thread approx 12” of
3/8” pipe into the tray
through the grommet.
Wetting the pipe end with
cold water helps harden
it, aiding insertion.
5
The 1/4” Blanking Grommet
should come ready-fitted in
the hole in the front of the tray
If growing outdoors remove
this grommet. If growing
indoors keep this grommet
in place.
3The 3/8” grommet (with
hole) will need fitting into the
square section of the tray.
From the outside of the tray
push the 3/8” grommet into
the hole in the tray wall.
4
8Align the ‘half moon’
section on the rear of
the AQUAvalve with the
‘T’ section in the tray.
Firmly push the
AQUAvalve onto the ‘T’.
7
Remove any slack in the
3/8” pipe by drawing
excess out of the tray.
9
12
Cut 3/8”/1/2” pipe to
appropriate length
If using 9 gal pot only:
Fit adaptive ring to
rim of module tray
10 11
Push 3/8” grommet into
reservoir, then push 3/8”
pipe through grommet.
Inside the tank push
3/8” filter into 3/8” pipe.
/