Grizzly T32428 Owner's manual

Brand: Grizzly

Model: T32428

Type: Owner's manual

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#CS22167 PRINTED IN CHINA V1.01.22

MODEL T32428

37" BEAR ROLL

OUTFEED SYSTEM

OWNER'S MANUAL

(For models manufactured since 11/21)

This manual provides critical safety instructions on the proper setup,

operation, maintenance, and service of this machine/tool. Save this

document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual

may result in fire or serious personal injury—including amputation,

electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.

This responsibility includes but is not limited to proper installation in

a safe environment, personnel training and usage authorization,

proper inspection and maintenance, manual availability and compre-

hension, application of safety devices, cutting/sanding/grinding tool

integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage

from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to the State

of California to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

Work in a well ventilated area, and work with approved safety equip-

ment, such as those dust masks that are specially designed to filter

out microscopic particles.

Table of Contents

INTRODUCTION ............................................... 2

Contact Info.................................................... 2

Manual Accuracy ........................................... 2

SECTION 1: SAFETY ....................................... 3

Safety Instructions for Machinery .................. 3

SECTION 2: SETUP ......................................... 5

Needed for Setup ........................................... 5

Unpacking ...................................................... 5

Inventory ........................................................ 6

Hardware Recognition Chart ......................... 7

Site Considerations ........................................ 8

Mounting ........................................................ 9

SECTION 3: OPERATIONS ........................... 13

Operation Overview ..................................... 13

Adjusting Cams ............................................ 14

Raising/Lowering Roller System .................. 15

SECTION 4: MAINTENANCE ......................... 16

Schedule ...................................................... 16

Cleaning & Protecting .................................. 16

Lubrication ................................................... 16

SECTION 5: SERVICE ................................... 17

Troubleshooting ........................................... 17

SECTION 6: PARTS ....................................... 18

Main ............................................................. 18

Labels & Cosmetics ..................................... 20

WARRANTY & RETURNS ............................. 21

IMPORTANT NOTICE!

Table Saw Modifications Required for Installation

The Model T32428 can be installed on a wide range of cabinet-type table saw brands and sizes.

Installation usually requires permanent modification to your table saw or its parts. This modification may

include cutting, grinding, drilling, and tapping threads in metal surfaces. Read the following to determine

which type of modification may be required for your saw:

• If your table saw does not have mounting holes that match those in the Model T32428, you will need

to drill new holes in the cabinet.

• The low voltage controller box on some Delta Unisaws may need to be lowered a few inches to

create clearance for the roller system.

CAUTION: For your own safety and protection of property, consult an electrician if you are

unsure about wiring practices or electrical codes required for moving a low voltage controller box.

Before beginning any modification to your table saw or its parts, read the entire assembly section in this

manual to make sure the person making the modification is capable of performing the required tasks,

and to make sure the Model T32428 will fit your saw.

Specifications

Main Specifications

Table Size ................................................................................................................................. 36-1/2 x 31 in.

Weight ................................................................................................................................................... 48 lbs.

Construction

Rollers ...........................................................................................................................Chrome, Ball Bearing

Frame ........................................................................................................................................ Formed Steel

Paint Type/Finish ................................................................................................................................. Enamel

-2- Model T32428 (Mfd. Since 11/21)

We stand behind our machines! If you have ques-

tions or need help, contact us with the information

below. Before contacting, make sure you get the

serial number

and manufacture date

from the

machine ID label. This will help us help you faster.

Grizzly Technical Support

1815 W. Battlefield

Springfield, MO 65807

Phone: (570) 546-9663

Email: [email protected]

We want your feedback on this manual. What did

you like about it? Where could it be improved?

Please take a few minutes to give us feedback.

Grizzly Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: [email protected]

Contact Info

We are proud to provide a high-quality owner’s

manual with your new machine!

made every effort to be exact with the

instruc-

tions, specifications, drawings, and photographs

in this manual. Sometimes we make mistakes, but

our policy of continuous improvement also means

that

sometimes the machine

you receive is

slightly different than shown in the manual

If you find this to be the case, and the difference

between the manual and machine leaves you

confused or unsure about something

check our

website for an updated version. W

e post

current

manuals and

manual updates for free

on our web-

site at

www.grizzly.com.

Alternatively, you can call our Technical Support

for help. Before calling, make sure you write

down the

manufacture date and

serial number

from the machine ID label (see below). This

information is required for us to provide proper

tech support, and it helps us determine if updated

documentation is available for your machine.

Manufacture Date

Serial Number

Manual Accuracy

INTRODUCTION

Like all machinery there is potential danger

when operating this equipment. Accidents

are frequently caused by lack of familiarity

or failure to pay attention. Use this machine

with respect and caution to decrease the

risk of operator injury. If normal safety pre-

cautions are overlooked or ignored, seri-

ous personal injury may occur.

No list of safety guidelines can be com-

plete. Every shop environment is different.

Always consider safety first, as it applies

to your individual working conditions. Use

this equipment and machinery with caution

and respect. Failure to do so could result in

serious personal injury, damage to equip-

ment, or poor work results.

Model T32428 (Mfd. Since 11/21) -3-

ELECTRICAL EQUIPMENT INJURY RISKS.

You can be shocked, burned, or killed by touching

live electrical components or improperly grounded

machinery. To reduce this risk, only allow qualified

service personnel to do electrical installation or

repair work, and always disconnect power before

accessing or exposing electrical equipment.

DISCONNECT POWER FIRST.

Always discon-

nect machine from power supply BEFORE mak-

ing adjustments, changing tooling, or servicing

machine. This prevents an injury risk from unin-

tended startup or contact with live electrical com-

ponents.

EYE PROTECTION. Always wear ANSI-approved

safety glasses or a face shield when operating or

observing machinery to reduce the risk of eye

injury or blindness from flying particles. Everyday

eyeglasses are NOT approved safety glasses.

OWNER’S MANUAL. Read and understand this

owner’s manual BEFORE using machine.

TRAINED OPERATORS ONLY. Untrained oper-

ators have a higher risk of being hurt or killed.

Only allow trained/supervised people to use this

machine. When machine is not being used, dis-

connect power, remove switch keys, or lock-out

machine to prevent unauthorized use—especially

around children. Make your workshop kid proof!

DANGEROUS ENVIRONMENTS. Do not use

machinery in areas that are wet, cluttered, or have

poor lighting. Operating machinery in these areas

greatly increases the risk of accidents and injury.

MENTAL ALERTNESS REQUIRED. Full mental

alertness is required for safe operation of machin-

ery. Never operate under the influence of drugs or

alcohol, when tired, or when distracted.

For Your Own Safety, Read Instruction

Manual Before Operating This Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions.

This manual uses a series of symbols and signal words intended to convey the level of impor-

tance of the safety messages. The progression of symbols is described below. Remember that

safety messages by themselves do not eliminate danger and are not a substitute for proper

accident prevention measures. Always use common sense and good judgment.

Indicates a potentially hazardous situation which, if not avoided,

MAY result in minor or moderate injury. It may also be used to alert

against unsafe practices.

Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

Alerts the user to useful information about proper operation of the

machine to avoid machine damage.

NOTICE

Safety Instructions for Machinery

SECTION 1: SAFETY

-4- Model T32428 (Mfd. Since 11/21)

WEARING PROPER APPAREL. Do not wear

clothing, apparel or jewelry that can become

entangled in moving parts. Always tie back or

cover long hair. Wear non-slip footwear to reduce

risk of slipping and losing control or accidentally

contacting cutting tool or moving parts.

HAZARDOUS DUST. Dust created by machinery

operations may cause cancer, birth defects, or

long-term respiratory damage. Be aware of dust

hazards associated with each workpiece mate-

rial. Always wear a NIOSH-approved respirator to

reduce your risk.

HEARING PROTECTION. Always wear hear-

ing protection when operating or observing loud

machinery. Extended exposure to this noise

without hearing protection can cause permanent

hearing loss.

REMOVE ADJUSTING TOOLS. Tools left on

machinery can become dangerous projectiles

upon startup. Never leave chuck keys, wrenches,

or any other tools on machine. Always verify

removal before starting!

USE CORRECT TOOL FOR THE JOB. Only use

this tool for its intended purpose—do not force

it or an attachment to do a job for which it was

not designed. Never make unapproved modifica-

tions—modifying tool or using it differently than

intended may result in malfunction or mechanical

failure that can lead to personal injury or death!

AWKWARD POSITIONS. Keep proper footing

and balance at all times when operating machine.

Do not overreach! Avoid awkward hand positions

that make workpiece control difficult or increase

the risk of accidental injury.

CHILDREN & BYSTANDERS. Keep children and

bystanders at a safe distance from the work area.

Stop using machine if they become a distraction.

GUARDS & COVERS. Guards and covers reduce

accidental contact with moving parts or flying

debris. Make sure they are properly installed,

undamaged, and working correctly BEFORE

operating machine.

FORCING MACHINERY. Do not force machine.

It will do the job safer and better at the rate for

which it was designed.

NEVER STAND ON MACHINE. Serious injury

may occur if machine is tipped or if the cutting

tool is unintentionally contacted.

STABLE MACHINE. Unexpected movement dur-

ing operation greatly increases risk of injury or

loss of control. Before starting, verify machine is

stable and mobile base (if used) is locked.

USE RECOMMENDED ACCESSORIES. Consult

this owner’s manual or the manufacturer for rec-

ommended accessories. Using improper acces-

sories will increase the risk of serious injury.

UNATTENDED OPERATION. To reduce the

risk of accidental injury, turn machine OFF and

ensure all moving parts completely stop before

walking away. Never leave machine running

while unattended.

MAINTAIN WITH CARE. Follow all maintenance

instructions and lubrication schedules to keep

machine in good working condition. A machine

that is improperly maintained could malfunction,

leading to serious personal injury or death.

DAMAGED PARTS. Regularly inspect machine

for damaged, loose, or mis-adjusted parts—or

any condition that could affect safe operation.

Immediately repair/replace BEFORE operating

machine. For your own safety, DO NOT operate

machine with damaged parts!

MAINTAIN POWER CORDS. When disconnect-

ing cord-connected machines from power, grab

and pull the plug—NOT the cord. Pulling the cord

may damage the wires inside. Do not handle

cord/plug with wet hands. Avoid cord damage by

keeping it away from heated surfaces, high traffic

areas, harsh chemicals, and wet/damp locations.

EXPERIENCING DIFFICULTIES. If at any time

you experience difficulties performing the intend-

ed operation, stop using the machine! Contact our

Technical Support at (570) 546-9663.

Model T32428 (Mfd. Since 11/21) -5-

SECTION 2: SETUP

This equipment presents

serious injury hazards

to untrained users. Read

through this entire manual

to become familiar with the

controls and operations

before using equipment!

Wear safety glasses during

the entire setup process!

Description Qty

• Safety Glasses (for Each Person) .............. 1

• Tape ............................................ As Needed

• Framing Square .......................................... 1

• Machinist's Square 6" ................................. 1

• Steel Hammer ............................................ 1

• Center Punch ............................................. 1

• Hand Drill .................................................... 1

• Drill Bit 11 ⁄32" ................................................ 1

• Another Person .......................................... 1

• Open-End Wrenches 13mm ....................... 2

• Straightedge 4' ........................................... 1

Needed for Setup

Unpacking

The following items are needed, but not included,

for the setup/assembly of this equipment.

This equipment was carefully packaged for safe

transport. When unpacking, separate all enclosed

items from packaging materials and inspect them

for shipping damage. If items are damaged,

please call us immediately at (570) 546-9663.

IMPORTANT: Save all packaging materials until

you are completely satisfied with the equipment

and have resolved any issues between Grizzly or

the shipping agent. You MUST have the original

packaging to file a freight claim. It is also extremely

helpful if you need to return your equipment later.

Lifting heavy machinery

or parts without proper

assistance or equipment

may result in strains, back

injuries, crushing injuries,

or property damage.

-6- Model T32428 (Mfd. Since 11/21)

Inventory

The following is a list of items shipped with the

roller system. Before beginning setup, lay these

items out and inventory them.

If any non-proprietary parts are missing (e.g. a

nut or a washer), we will gladly replace them; or

for the sake of expediency, replacements can be

obtained at your local hardware store.

Inventory (Figures 1–2) Qty

A. Roller System ............................................. 1

B. Mounting Stud Pads M8-1.25 ..................... 2

C. Hex Bolts M8-1.25 x 25 .............................. 4

D. Lock Washers 8mm.................................... 4

E. Hex Nuts M8-1.25 ....................................... 4

F. Flat Washers 8mm ..................................... 6

G. Mounting Template (Not Shown) ................ 1

Figure 1. Roller system.

Figure 2. Loose inventory.

NOTICE

If you cannot find an item on this list,

carefully check around/inside the equip-

ment and packaging materials. Often, these

items get lost in packaging materials while

unpacking or they are pre-installed at the

factory.

Model T32428 (Mfd. Since 11/21) -7-

Hardware Recognition Chart

USE THIS CHART TO MATCH UP

HARDWARE DURING THE INVENTORY

AND ASSEMBLY PROCESS.

5mm

Flat

Head

Cap

Screw

-8- Model T32428 (Mfd. Since 11/21)

Site Considerations

Figure 3. Minimum working clearances.

40" (From Saw Cabinet)

36½"

Weight Load

Refer to the Machine Data Sheet for the weight

of your table saw. Make sure that the surface

upon which the machine is placed will bear the

weight of the machine, additional equipment that

may be installed on the machine, and the heaviest

workpiece that will be used. Additionally, consider

the weight of the operator and any dynamic load-

ing that may occur when operating the machine.

Physical Environment

The physical environment where a machine is

operated is important for safe operation and lon-

gevity of components. For best results, use this

equipment in a dry environment that is free from

excessive moisture, hazardous chemicals, air-

borne abrasives, or extreme conditions. Extreme

conditions for this type of equipment are gener-

ally those where the ambient temperature range

is outside 41°–104°F; the relative humidity range

is outside 20–95% (non-condensing); or the envi-

ronment is subject to vibration, shocks, or bumps.

Children or untrained people

may be seriously injured by

table saw. Only install in an

access restricted location.

Lighting

Lighting around the machine must be adequate

enough that operations can be performed safely.

Shadows, glare, or strobe effects that may distract

or impede the operator must be eliminated.

Space Allocation

Consider the largest size of workpiece that will

be processed with this equipment and provide

enough space around the machine and roller

system for adequate operator material handling or

the installation of auxiliary equipment. With per-

manent installations, leave enough space around

the table saw to open or remove doors/covers

as required by the maintenance and service

described in its manual. See below for required

space allocation for this roller system.

Model T32428 (Mfd. Since 11/21) -9-

Mounting

To mount system:

1. DISCONNECT SAW FROM POWER!

2. Tape mounting template to table saw cabinet

rear (see Figure 4). Baseline must be parallel

with and 41⁄2" from table surface.

The mounting process typically requires modi-

fication of your table saw. Be sure to read the

Important Notice on Page 1.

To make the process easier, we strongly recom-

mend that you have another person to help you.

Before beginning the mounting process, refer to

Needed for Setup and gather all listed items.

Note: If table saw has no cabinet access

panel or door, you may need to turn machine

on its side and access holes from underneath

machine.

4. Remove mounting template and drill (4) 11 ⁄32"

holes at locations marked in Step 3 (see

Figure 5).

Tip: Drill pilot holes using smaller bit before

enlarging to 11⁄32 for best results.

5. Open cabinet access panel or door to insert

(2) M8-1.25 mounting stud pads through

holes (see Figure 5).

Lifting heavy machinery

or parts without proper

assistance or equipment

may result in strains, back

injuries, crushing injuries,

or property damage.

Baseline

Figure 4. Mounting template taped to table

saw cabinet rear with baseline 41⁄2" below table

surface.

Figure 5. Mounting stud pads inserted.

Mounting Stud

Pads

3. Use center punch to mark (4) mounting holes

indicated on mounting template.

41⁄2"

-10- Model T32428 (Mfd. Since 11/21)

7. Loosen (2) cam lock knobs, adjust roller sys-

tem until lock knobs are in UP position (see

Figure 7), then tighten lock knobs.

8. Extend straightedge off of saw table surface

to highest rollers (see Figure 8).

10. Lift roller frame to straighten folding support

arm and extend roller frame (see Figure 9).

Figure 9. Extending roller frame.

9. Adjust roller system until three highest rollers

are parallel with table surface, then tighten

hardware from Step 6.

Figure 7. Cam lock knobs in UP position.

Cam Lock Knob

(1 of 2)

Figure 8. Using straightedge to check roller

frame position.

Straightedge

Highest Roller

(1 of 3)

Figure 6. Roller system attached to cabinet.

x 2

Roller

System

6. With help from another person, attach roller

system to mounting stud pads with (2) M8-1.25

x 25 hex bolts, (4) 8mm lock washers, (4)

8mm flat washers, and (2) M8-1.25 hex nuts

(see Figure 6). Finger-tighten for now.

Model T32428 (Mfd. Since 11/21) -11-

11. Loosen (4) hex nuts shown in Figure 10.

Figure 10. Location of adjustment plate hex

nuts.

x 4

14. Mark and drill 11⁄32" mounting holes at loca-

tions shown in Figure 13.

— If there is not a dust port or other fixture

in cabinet preventing this step, proceed to

Step 16.

— If there is a dust port or other fixture in

cabinet preventing this step, proceed to

Step 15.

Figure 13. Location of lower mounting holes.

13. With straightedge extended over saw table

and outermost rollers (see Figure 12), adjust

hex bolt shown in Figure 11 until outermost

rollers are parallel with table surface, then

tighten hex nuts from Step 11 to secure

position.

Figure 12. Straightedge extended to outermost

rollers.

Outermost Rollers

12. Loosen jam nut shown in Figure 11.

Figure 11. Location of roller frame adjustment

hex bolt and jam nut.

Straightedge

-12- Model T32428 (Mfd. Since 11/21)

16. Secure support bracket to cabinet through

holes drilled in Step 14 with (2) M8-1.25 x 25

hex bolts, 8mm flat washers, and M8-1.25

hex nuts (see Figure 15).

Figure 15. Lower portion of mounting arm

secured to cabinet.

x 2

Support Bracket

15. Remove (2) hex nuts, lock washers, flat

washers, and hex bolts shown in Figure 14,

move support bracket up or down to holes in

mounting beam where it has the necessary

clearance, install with hex nuts, lock wash-

ers, flat washers, and hex bolts, then repeat

Step 14.

Figure 14. Location of support bracket and

fasteners.

x 2

Mounting Beam

Support

Bracket

Model T32428 (Mfd. Since 11/21) -13-

SECTION 3: OPERATIONS

Operation Overview To complete a typical operation, the operator

does the following:

1. Examines workpiece to make sure it is suit-

able for cutting.

2. Adjusts blade tilt, if necessary, to correct

angle for desired cut.

3. Adjusts blade height approximately 1⁄4" higher

than thickness of workpiece.

4. Adjusts fence to desired width of cut, then

locks it in place.

5. Adjusts roller system cams as needed for

operation.

6. Checks roller system for proper support

and to make sure the workpiece can safely

pass all the way through the blade without

interference.

7. Puts on safety glasses, respirator, and hear-

ing protection, and locates push sticks/blocks

if needed.

8. Starts dust collection system, then starts

saw.

9. Feeds workpiece all the way through blade

while maintaining firm pressure on workpiece

against table and fence, and keeping hands

and fingers out of blade path and away from

blade.

10. Stops machine immediately after cut is

complete.

The purpose of this overview is to provide the nov-

ice machine operator with a basic understanding

of how the equipment is used during operation,

so the controls/components discussed later in this

manual are easier to understand.

Due to the generic nature of this overview, it is

not intended to be an instructional guide. To learn

more about specific operations, refer to the table

saw manual for information on safely operating

your table saw, read this entire manual, seek

additional training from experienced machine

operators, and do additional research outside

of this manual by reading "how-to" books, trade

magazines, or websites.

To reduce your risk of

serious injury, read this

entire manual BEFORE

using roller system.

Eye injuries, respiratory problems, or hear-

ing loss can occur while operating table

saw. Wear personal protective equipment

to reduce your risk from these hazards.

Dynamic forces involved with processing

large/heavy workpieces may cause

unsecured roller system to shift during

cutting operations, which could result

in kickback injuries. To reduce this risk,

properly secure roller tables to outfeed side

of machine.

-14- Model T32428 (Mfd. Since 11/21)

The cams on the Model T32428 have two posi-

tions: UP and DOWN.

The UP position aligns the rollers with the surface

of the table saw table (see Figure 16). This posi-

tion cannot be used with fixtures in the miter slot

of the table, as these will contact the roller system

as the workpiece exits the outfeed side of the

machine.

Adjusting Cams Loosen the cam lock knob on either side of the

roller system, move lock knobs to the position

indicated on the cam labels (see Figure 18), then

tighten the lock knobs.

Figure 18. Cam lock knob positions.

The DOWN position gives extra clearance to

allow for a miter gauge or other sliding fixture (see

Figure 17).

Figure 16. Cams in UP position.

Figure 17. Cams in DOWN position.

Rollers Aligned with

Table Surface

Rollers Slightly Below

Table Surface

Model T32428 (Mfd. Since 11/21) -15-

Raising/Lowering

Roller System

Figure 20. Lowering roller system.

Keep fingers away from hinge points to

prevent pinch injuries.

The roller system should be lowered whenever it

is not needed for outfeed support to prevent over-

reaching and to save space.

Lowering Roller System

To lower the roller system, grip the outermost roll-

ers or the roller frame. Slightly lift the frame and

push the hinge point on the folding support arm

with your foot. This will unlock the frame so it can

be lowered.

Raising Roller System

To raise the roller system, simply grip the outer-

most rollers or roller frame, then lift the frame until

the folding support arm locks in place.

Figure 19. Raising roller system.

-16 - Model T32428 (Mfd. Since 11/21)

SECTION 4: MAINTENANCE

To reduce risk of shock or

accidental startup, always

disconnect machine from

power before adjustments,

maintenance, or service.

For optimum performance from this equipment,

this maintenance schedule must be strictly

followed.

Ongoing

To minimize your risk of injury and maintain proper

operation, stop use of equipment immediately if

you ever observe any of the items below, and fix

the problem before continuing operations:

• Loose mounting bolts.

• Damaged rollers.

• Any other unsafe condition.

Weekly Maintenance

• Clean rollers and hinge points.

Monthly Maintenance

• Clean roller frame, support bracket, and

mounting beam.

• Lubricate rollers and hinge points.

Schedule

Cleaning the Model T32428 is relatively easy.

Vacuum excess wood chips and sawdust, and

wipe off the remaining dust with a dry cloth. If any

resin has built up, use a resin dissolving cleaner

to remove it.

Cleaning &

Protecting

Keep hinge and pivot points and roller axles lubri-

cated for smooth operation and long life of your

equipment.

Lubrication

Hinge & Pivot Points

Oil Type .................T26685 or ISO 32 Equivalent

Oil Amount ....................................... 1 or 2 Drops

Lubrication Frequency .............................Monthly

Items Needed Qty

Mineral Spirits .................................... As Needed

Wire Brushes ..................................... As Needed

Shop Rags ......................................... As Needed

T26685 or ISO 32 Equivalent ............ As Needed

Use a rag to clean any built-up resin or dust from

hinge and pivot points (see Figure 21) before

applying a few drops of lubricant to these loca-

tions. Lower and raise roller system a couple

times to distribute the lubricant.

Figure 21. Location of hinge and pivot points.

Clean each roller with mineral spirits before apply-

ing a drop of lubricant at each roller axle.

Roller Axles

Oil Type .................T26685 or ISO 32 Equivalent

Oil Amount ................................................ 1 Drop

Lubrication Frequency .............................Monthly

Hinge Point

Pivot Point

Model T32428 (Mfd. Since 11/21) -17-

SECTION 5: SERVICE

Troubleshooting

Operations

Symptom Possible Cause Possible Solution

Roller will not

turn smoothly.

1. Roller axle requires lubrication.

2. Bearing inside roller has failed.

1. Clean and lubricate roller axle (Page 16).

2. Replace roller.

Roller system

will not lower.

1. Hinge and pivot point require lubrication.

2. Folding support arm fasteners are too tight.

1. Clean and lubricate hinge and pivot points (Page 16).

2. Loosen fasteners.

Rollers are

not parallel

with table saw

surface.

1. Roller frame adjustment plate is adjusted

incorrectly.

1. Adjust roller frame adjustment plate (Page 11).

Review the troubleshooting procedures in this section if a problem develops with your equipment. If you

need replacement parts or additional help with a procedure, call our Technical Support. Note: Please

gather the serial number and manufacture date of your equipment before calling.

-18- Model T32428 (Mfd. Since 11/21)

BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Main

SECTION 6: PARTS

We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown

are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability.

Page is loading ...

Grizzly T32428 Owner's manual

Grizzly T32428 Owner's manual

Grizzly T32428 Owner's manual

Related papers

Other documents