Wen DF475T User manual

Category
Power generators
Type
User manual
A A
B B
C C
D D
E E
F F
G G
H H
J J
K K
L L
M M
N N
P P
R R
T T
24
24
23
23
22
22
21
21
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
DRAWN
CHK'D
APPV'D
MFG
Q.A
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
FINISH:
DEBURR AND
BREAK SHARP
EDGES
NAME
SIGNATURE
DATE
MATERIAL:
DO NOT SCALE DRAWING
REVISION
TITLE:
DWG NO.
SCALE:1:5
SHEET 1 OF 1
A0
WEIGHT:
GLT WEN4750
IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability,
ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged,
trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use
your tool properly and for its intended purpose, you will enjoy years of safe, reliable service.
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact us:
TECHSUPPOR[email protected]1-847-429-9263 (M-F 8AM-5PM CST)
For replacement parts and the most up-to-date instruction manuals, visit WENPRODUCTS.COM
4750-WATT
DUAL FUEL GENERATOR
Instruction Manual
MODEL DF475T
Introduction ............................................................................................. 2
Safety Information ................................................................................... 4
Generator Safety Warnings ......................................................................5
Know Your Generator ............................................................................... 8
Unpacking & Assembly .......................................................................... 10
Generator Preparation ............................................................................ 12
Starting the Generator ............................................................................ 19
Using the Generator ............................................................................... 21
Shutting Off the Generator ..................................................................... 24
Maintenance ........................................................................................... 25
Transportation & Storage .......................................................................32
Specifications ......................................................................................... 33
Exploded View & Parts List .................................................................... 34
Wiring Diagram ...................................................................................... 38
Troubleshooting Guide ........................................................................... 39
Warranty Statement ...............................................................................40
TABLE OF CONTENTS
Your generator is compatible with the WEN 55201 Magnetic Oil Dipstick,
available at wenproducts.com
Model Number DF475, DF475T
Rated Wattage Gasoline: 3800 Watts, LPG: 3500 Watts
Surge Wattage Gasoline: 4750 Watts, LPG: 4350 Watts
Frequency 60Hz
Rated Voltage AC: 120V/240V, DC: 12V
Rated Amperage AC: 32A/16A, DC: 8A
Engine OHV, 4 stroke, single cylinder, 224cc
Fuel Tank Capacity 4 US gallons (15 L), 87 octane minimum
Oil Capacity 20.3 fl. oz. (0.6 L)
Half-Load Run Time Gasoline: 11 hours
LPG (with 20 lb tank): 7 hours
Product Dimensions 23.2 x 17.5 x 18.5 in. (L x W x H)
Product Net Weight 105.8 lbs (48 kg)
SPECIFICATIONS
2
INTRODUCTION
THANKS FOR PURCHASING THE WEN GENERATOR!
Refer to the illustration below for the location of the serial number. Record the generator information in the spaces
provided below. If assistance for information or service is required, please contact the Customer Service Help Line
by calling 1-847-429-9263, M-F 8-5 CST; you will be asked to provide the following generator information when
calling.
GENERATOR MODEL NUMBER: WEN DF475, WEN DF475T
DATE OF PURCHASE: __________________________________________
PURCHASED FROM: ___________________________________________
SERIAL NUMBER: _____________________________________________
Record the service dates of your generator in the chart below. Please perform maintenance checks and operations
according to the “MAINTENANCE” section of the manual.
Service Record Date Date Date Date Date Date
Change Oil
Change Spark Plug
Clean Air Cleaner
Clean Spark Arrestor
Clean Fuel Tank
TO MAXIMIZE THE LIFESPAN OF YOUR GENERATOR:
We recommend running your generator at least ONCE A MONTH for 20 to 30 minutes. Start the generator ac-
cording to the instructions and plug a small load in to make sure the outlet is producing electricity.
SERVICE RECORD
A A
B B
C C
D D
E E
F F
G G
H H
J J
K K
L L
M M
N N
P P
R R
T T
24
24
23
23
22
22
21
21
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
DRAWN
CHK'D
APPV'D
MFG
Q.A
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
FINISH:
DEBURR AND
BREAK SHARP
EDGES
NAME
SIGNATURE
DATE
MATERIAL:
DO NOT SCALE DRAWING
REVISION
TITLE:
DWG NO.
SCALE:1:5
SHEET 1 OF 1
A0
WEIGHT:
GLT WEN4750
Serial Number
3
DANGER: indicates a hazard, which, if not avoided, will result in death or serious injury.
WARNING: indicates a hazard, which, if not avoided, could result in death or serious injury.
CAUTION: indicates a hazard, which, if not avoided, might result in minor or moderate injury.
CAUTION: when used without the alert symbol, indicates a situation that could result in damage to the
machine.
QUESTIONS? PROBLEMS?
In order to answer questions and solve problems in the most efficient and speedy manner, contact Customer
Service at 1-847-429-9263, M-F 8-5 CST or email [email protected].
SAFETY SYMBOLS
The purpose of following safety symbols is to attract your attention to possible dangers. The safety symbols, and
their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves
eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention
measures.
SAFETY INTRODUCTION
Safety is a combination of common sense, staying alert, and knowing how your tool works. This manual contains
important information regarding the generator’s potential safety concerns, as well as preparation, operation, and
maintenance instructions. Before operating this generator, be sure to read and observe all warnings and instruc-
tions both on the generator labels and in this instruction manual. Failure to follow all instructions listed below may
result in personal injury.
NOTE: The following safety information is not meant to cover all possible conditions and situations that may oc-
cur. WEN reserves the right to change this product and specifications at any time without prior notice.
SAVE THESE INSTRUCTIONS - Please keep this manual available to all users during the entire life of the tool.
Review it frequently to maximize safety for both yourself and others.
WARNING: Before operating the generator, make sure to read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire or serious injury.
NOTICE REGARDING EMISSIONS
Engines that are certified to comply with U.S. EPA emission regulations for SORE (Small Off Road Equipment), are
certified to operate on regular unleaded gasoline, and may include the following emission control systems: (EM)
Engine Modifications and (TWC) Three-Way Catalyst (if so equipped).
SAFETY INFORMATION
4
GENERATOR SAFETY WARNINGS
DANGER! CARBON MONOXIDE
Using a generator indoors CAN KILL YOU IN MINUTES. Generator exhaust contains carbon monoxide (CO). This
is a poison gas you cannot see or smell. If you can smell the generator exhaust, you are breathing CO. But even
if you cannot smell the exhaust, you could be breathing CO.
NEVER use a generator inside homes, garages, crawl spaces, or other partially enclosed areas. Deadly levels
of carbon monoxide can build up in these areas. Using a fan or opening windows and doors does NOT supply
enough fresh air. ONLY use a generator outside and far away from windows, doors, and vents. These openings
can pull in generator exhaust.
Even if you use a generator correctly, CO may leak into the home. ALWAYS use a battery-powered or battery-
backup CO alarm in the home. If you start to feel sick, dizzy, or weak after the generator has been running, move
to fresh air RIGHT AWAY. See a doctor. You may have carbon monoxide poisoning.
WARNING! RISK OF EXPLOSION. HIGHLY FLAMMABLE: This generator may emit highly flammable and
explosive gasoline vapors, which can cause severe burns or even death, if ignited. A nearby open flame can lead
to explosion even if not directly in contact with gasoline.
• Do not operate near open flame, heat, or any other ignition source. Do not smoke near the generator.
• Always operate on a firm, level surface.
Always turn generator off before refueling. Allow generator to cool for at least 2 minutes before removing
fuel cap. Loosen cap slowly to relieve pressure in tank.
Do not overfill fuel tank. Gasoline may expand during operation. Do not fill to the top of the tank. Allow for
expansion. Always check for spilled fuel before operating.
If fuel spills, move the generator at least 30 feet away from the spill and wipe clean any spilled fuel before
starting the engine.
• Empty fuel tank before storing or transporting the generator.
WARNING! If this generator is used as a supply for a building’s wiring system, the generator must be in-
stalled by a qualified electrician and connected to a transfer switch as a separately derived system in accordance
with all applicable laws and electrical codes and the National Electrical Code, NFPA 70. The generator shall be
connected to a transfer switch that switches all conductors excluding the equipment grounding conductor. The
frame of the generator shall be connected to an approved grounding electrode.
CALIFORNIA PROPOSITION 65 WARNING: This product contains chemicals and produces exhaust known
to the State of California to cause cancer, birth defects and other reproductive harm. For more information, visit
www.P65Warnings.ca.gov
5
GENERATOR SAFETY WARNINGS
OPERATING ENVIRONMENT
1. Using a generator indoors can KILL YOU IN MINUTES. Only use a generator outside and far away from windows,
doors and vents.
2. Do not operate near open flame or flammable materials. This generator may emit highly flammable and explosive
gasoline vapors, which can cause severe burns or even death if ignited. A nearby open flame can lead to an explo-
sion even if it isn’t directly in contact with gasoline.
3. Do not smoke near the generator.
4. Do not use the generator in rainy or wet conditions; doing so significantly increases the risk of electrical shock.
5. Always operate the generator on a dry, firm, level surface.
6. Do not allow children or non-qualified persons to operate the generator.
7. Do not use or store LPG cylinder in a building, garage or enclosed area. Failure to do so will result in death or
serious injury. Liquid Petroleum Gas (LPG) is highly flammable and explosive. Flammable gas under pressure can
cause a fire or explosion if ignited. Always keep the LPG cylinder in an upright position. The LPG cylinder valve
should be turned OFF (closed) when generator is not in use; failure to do so could result in death or serious injury.
GENERATOR PREPARATION
1. Always ground the generator before using it to maximize safety (see “GROUND THE GENERATOR” section on
page 18).
2. Always make sure generator is turned OFF before filling the fuel tank. Do not overfill fuel tank, as gasoline may
expand during operation. Do not fill to the very top of the tank. Leave room for gasoline expansion. Always check
for spilled fuel before operating.
3. Do not use receptacles or cords that show signs of damage, such as broken or cracked insulation. If any part
of the generator or electrical device is broken, damaged, or defective, make sure it is repaired or replaced before
operation. Service should only be performed by a qualified technician.
4. Use a ground fault circuit interrupter (GFCI) in highly conductive areas such as metal decking or steel work.
Extension cords with in-line GFCIs are recommended for these operations to maximize safety.
5. NEVER connect the generator to a building’s electrical system without consulting a qualified electrician. Such
connections must comply with local electrical laws and codes. Failure to comply can create a back-feed, which
may result in serious injury or death to utility workers.
WARNING: Do not let comfort or familiarity with the product replace strict adherence to product safety
rules. Failure to follow the safety instructions may result in serious personal injury.
6
GENERATOR SAFETY WARNINGS
GENERATOR OPERATION
1. Only use the generator for its intended purposes. Modifying or using the generator for operations for which it
was not designed may cause hazards and personal injury.
2. Do not touch bare wires or receptacles (outlets).
3. Do not exceed the wattage capacity of the generator by plugging in more electrical devices than the unit can
handle.
4. Allow generator to run for several minutes before connecting electrical devices.
5. Do not exceed the wattage capacity of the generator by plugging in more electrical devices than the unit can
handle (see “OPERATION” section).
6. Do not turn on electrical devices until after they are connected to the generator.
7. Generators vibrate in normal use. During and after the use of the generator, inspect both the generator as well
as extension and power supply cords for damage resulting from vibration.
8. Do not touch HOT PARTS. This generator produces heat when running. Temperatures near exhaust can ex-
ceed 150º F (65º C). Allow generator to cool down after use before touching engine or areas of the generator that
become hot during use.
9. Turn off all connected electrical devices before stopping the generator.
10. Always turn generator off before refueling. Allow generator to cool for at least 2 minutes before removing fuel
cap. Loosen cap slowly to relieve pressure in tank.
11. Turn the engine switch to “OFF” position when the engine is not running.
12. Empty fuel tank before storing or transporting the generator. Do not store generator or gasoline near furnaces,
water heaters, or any other appliances that produce heat or have automatic ignitions. Store the generator and fuel
away from sparks, open flames, pilot lights, heat and other sources of ignition.
CAUTION: Misuse of this generator can damage it or shorten its lifespan.
TO MAXIMIZE THE LIFESPAN OF YOUR GENERATOR:
We recommend running your generator at least once a month for 20 to 30 minutes. Start the generator ac-
cording to the instructions and plug a small load in to make sure the outlet is producing electricity.
If you do not run it often, it will greatly shorten the generator’s lifespan and void the warranty.
7
KNOW YOUR GENERATOR
1. Pressure Relief Valve
2. Fuel Gauge
Indicates amount of fuel inside the fuel tank
E indicates Empty, F indicates Full
3. Choke Lever
Adjusts the amount of air let into the engine
during startup
4. Fuel Valve
Allows fuel to enter engine from the fuel tank
5. Air Filter
A case with a sponge-like element that filters the air
entering the engine
6. Recoil Starter
Pull cord for manually starting the engine
7. 224cc OHV Engine
8. Transportation Handle
For easy transport of the generator
(installed by user)
9. Gasoline Fuel Cap
Access to the fuel tank for adding gasoline
10. Fuel Tank
11. Control Panel
Refer to the next page for descriptions
12. Battery
Connect the battery before starting the generator
13. Oil Fill and Dipstick
For filling and checking oil
14. LPG Hose Connector
Connects to LPG hose and LPG cylinder
Use the illustration below to become familiar with all the components and controls of this generator. If any part is
damaged or missing, please contact our customer service at 1-847-429-9263, M-F 8-5 CST or email us at techsup-
A A
B B
C C
D D
E E
F F
G G
H H
J J
K K
L L
M M
N N
P P
R R
T T
24
24
23
23
22
22
21
21
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
DRAWN
CHK'D
APPV'D
MFG
Q.A
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
FINISH:
DEBURR AND
BREAK SHARP
EDGES
NAME
SIGNATURE
DATE
MATERIAL:
DO NOT SCALE DRAWING
REVISION
TITLE:
DWG NO.
SCALE:1:5
SHEET 1 OF 1
A0
WEIGHT:
GLT WEN4750
9
1
2
3
4
5
6
7
8
10
11
12
13
14
8
KNOW YOUR GENERATOR
1. Fuel Selector Dial
Turn the dial to select between gasoline
or LPG before operation.
2. Electric Start Key
Turn the key to start, run and stop the
engine.
3. DC 12V Receptacle
Cigarette lighter style receptacle, 12V DC, 8A.
4. DC Circuit Breaker
Thermal protector that protects the DC circuit from
overload.
5. AC 120V 20A NEMA 5-20 GFCI Receptacles
Connect electrical devices that run on 120V, 60 Hz,
single phase, AC current.
6. 20A Circuit Breaker (for 5-20R)
Thermal protector that protects the 5-20 receptacles
from overload.
KNOW YOUR CONTROL PANEL
7. Voltage Selector
Selects the voltage between 120V and 240V for the L14
-30 receptacle.
8. AC 120/240V 30A NEMA L14-30R
Twistlock Receptacle
Connect electrical devices that run on 120V/240V, 60 Hz,
single phase, AC current.
9. 16A Main Circuit Breakers
Thermal protectors that protect the generator’s main cir-
cuit from overload.
10. Grounding Nut
Ground generator to reduce risk of electric shock.
MODEL DF475
F
U
E
L
S
W
I
T
C
H
1 2 3 5
4
6
10
7 8
9
9
UNPACKING & ASSEMBLY
No. Accessory Qty.
43 Foot Support Assembly 2
44 Foot Support Isolator 2
32 M6X40 Bolt 4
45 M6 Nut 6
42 Wheel 2
48 Wheel Axle 2
16 Flat Washer 2
25 Cotter Pin 2
19 Handle 1
PACKING LIST
UNPACKING THE GENERATOR AND ACCESSORIES
Open the packaging and take out all loose parts from the box. With the help of a good friend or trustworthy foe,
carefully lift the generator from the packaging and place it on a sturdy, level surface.
Make sure all the accessories are accounted for and fully assemble the generator before discarding the packaging.
If any part is missing or broken, please contact our customer service at 1-847-429-9263, M-F 8-5 CST or email us
IMPORTANT: Two red shipping brackets have been added to
the bottom of your generator to protect the generator during
shipping. Please make sure to remove BOTH shipping brack-
ets before operation.
IMPORTANT: The LPG hose is packed underneath the fuel
tank, sitting above the engine. Remove to hose and set it aside
before assembling or operating the generator.
No. Accessory Qty.
49 Handle Connector 1
31 M8X35 Bolt 2
64 M8 Hex Nut 8
59 Handle Bolt 1
30 Handle Fixing Clip 1
15 M6X55 Bolt 1
N/A Spark Plug Wrench 1
N/A First Stage Regulator 1
N/A Oil Bottle 1
10
TO INSTALL THE FEET:
Slide two M6X40 bolts (32) through the foot support assembly (43) and the generator frame. Tighten with M6
nuts (45). Repeat for the other foot.
TO INSTALL THE WHEELS:
UNPACKING & ASSEMBLY
NOTE: Only the generator frame is shown to
maximize clarity for assembly.
NOTE: Connecting/disconnecting the battery’s negative terminal requires removing the right wheel. Before
installing the wheels, verify that the negative terminal of the battery has been connected securely. See p. 17.
Slide the wheel axle (48) through the wheel (42), flat washer (16), and wheel bracket on the frame. Insert a cotter
pin (25) through the hole on the end of the axle to keep the wheel in place. Repeat for the other wheel.
TO INSTALL THE HANDLE:
Slide the M8X35 bolts (31) through the handle connector (49) and the frame. Tighten with the M8 nuts (64). Slide
the handle bolt (59) through the handle connector (49) and the handle (19), and tighten with M8 nut (64).
Next, install the handle fixing clip (30). Insert the M6X55 bolt (15) through the frame and handle fixing clip (30)
and tighten with M6 nut (45).
11
The following section describes the necessary steps to prepare the generator for use. If you are unsure about how
to perform any of the steps please call 1-847-429-9263 M-F 8-5 CST for customer service. Failure to perform these
steps properly can damage the generator or shorten its life.
STEP 1 - ADD/CHECK OIL
The generator is shipped without oil. User must add the proper amount of oil before operating the generator for
the first time. The oil capacity of the engine crankcase is 20.3 fl. oz (0.6 L).
Oil Dipstick
Lower Level
Fill Line
Upper Level
Fill Line
2. Unscrew the oil dipstick from the engine.
3. Using an oil funnel or appropriate dispenser, slowly add oil into
the oil fill (Fig. 2), being careful not to overfill the unit. Fill the crank-
case to the upper fill line so you can visually see the oil coming
halfway up the oil fill threads (Fig. 3).
4. Reinstall the oil dipstick and firmly tighten it. Wipe clean any
spilled oil.
32
-30 -20 -10 0 10 20 30
-20 0 20 40 60 80 100
40
°F
°C
Synthetic 5W-30
30
10W-30
• 30W engine oil for temperatures
above 40°F.
• 10W-30 engine oil for temperatures
between 0°F - 40°F.
• Synthetic 5W-30 engine oil for all
temperature ranges.
ENGINE OIL RECOMMENDATIONS - Select good quality detergent oil bearing the American Petroleum Insti-
tute (API) service classifications SJ, SL, or SM (synthetic oils may be used). Select the SAE viscosity grade
of oil that matches the expected operating temperature. For general use (above 40° F), we recommend 30W
engine oil.
Fig. 1 - Oil Recommendation Chart
CAUTION: Keep the generator level! Tilting the generator to
assist in filling will cause oil to flow into the wrong areas of the
engine and will cause damage.
GENERATOR PREPARATION
To add oil, follow these steps:
1. Place the generator on a level surface. Make sure the engine is
OFF before adding or checking oil.
Fig. 2
Fig. 3
12
GENERATOR PREPARATION
For subsequent operation, the oil level should be checked before each use, or after every 8 hours of operation. The
generator is equipped with a low-oil sensor and will NOT start without a sufficient amount of oil.
Upper Limit
Lower Limit
To check oil level (before every subsequent start):
1. Place the generator on a level surface. Make sure the engine is OFF
before adding or checking oil.
2. Remove and wipe the dipstick with a clean rag.
3. Insert the dipstick into the oil fill without screwing it in. Remove the
dipstick to check the oil mark (Fig. 4).
If the oil mark covers less than one half of the dipstick, slowly add oil until
the oil mark reaches to the top of the dipstick (or when you can see the oil
coming halfway up the oil fill threads).
4. Wipe clean any oil leaks and firmly tighten the dipstick.
OIL LEVEL SHUTDOWN
To protect the unit from damage, the generator is equipped with a low-oil-
pressure shutoff that will automatically shut down the engine when the oil
level is too low. The oil level of the engine should be checked before each
start to ensure that the engine crankcase contains sufficient lubricant.
TIP: Your WEN generator is compatible with the WEN 55201 Magnetic Oil Dipstick (not included), available for
purchase at wenproducts.com. The dipstick’s industrial-strength magnetic tip will collect metal shavings from
your generator’s oil tank to help preserve the engine and extend your generator’s lifespan.
Fig. 4
13
GENERATOR PREPARATION
STEP 2 - ADD/CHECK FUEL
IMPORTANT:
• Never use an oil/gasoline mixture.
• Never use old gasoline.
• Keep gasoline away from sparks, open
flames, pilot lights, heat and other sources of
ignition.
• Avoid getting dirt or water into the fuel tank.
• Gasoline can age in the tank and make
starting difficult. Never store generator for
more than 2 months with fuel in the tank.
GASOLINE WARNING: Keep generator away from open flame. This generator may emit highly flammable
and explosive gasoline vapors, which can cause severe burns or even death if ignited. A nearby open flame can
lead to explosion even if not directly in contact with gasoline.
• Do not operate near open flame.
• Do not smoke near the generator.
• Always operate on a firm, level surface.
• Always turn generator off before refueling. Allow generator to cool for at least 2 minutes before removing fuel
cap. Loosen cap slowly to relieve pressure in tank.
• Do not overfill fuel tank. Fuel may expand during operation. Do not fill to the top of the tank. Allow for expan-
sion.
• Always check for spilled fuel before operating. Clean up any spilled fuel before starting.
• Empty fuel tank before storing or transporting the generator to prevent spilling.
Use ONLY fresh (within 30 days from purchase), lead-free gasoline with a minimum of 87 octane rating. The gen-
erator performs best with ethanol-free gasoline. DO NOT use gasoline with over 10% ethanol.
The capacity of the fuel tank is 6.6 gallons. DO NOT mix oil with gasoline.
To add gasoline, follow these steps:
1. Make sure the generator is shut OFF and on a level surface.
Unscrew the fuel cap (Fig. 5) and set it aside. The fuel cap may
be tight and hard to unscrew.
2. Slowly add unleaded gasoline to the fuel tank. Be careful not
to overfill.
NOTE: Do not fill the fuel tank to the very top. If you do so,
gasoline will expand and spill during use, even with the fuel cap
in place.
3. Reinstall fuel cap and wipe clean any spilled gasoline with a
dry cloth.
To check fuel level
(before every subsequent start):
Before starting the generator, check the fuel gauge to see if
there is sufficient fuel inside the tank. “E” indicates Empty and
“F” indicates Full. Refill the fuel tank as necessary.
Fuel Cap
Fuel Gauge
FUEL OPTION A: GASOLINE
Fig. 5
14
GENERATOR PREPARATION
DANGER: EXPLOSION AND FIRE. LP vapors are extremely flammable and explosive. Do not use or store
LP cylinder in a building, garage or enclosed area. Failure to do so will result in death or serious injury.
WARNING: EXPLOSION AND FIRE. The cylinder valve should be turned OFF (closed) when generator is
not in use. Failure to do so could result in death or serious injury.
• Always keep the LPG cylinder in an upright position.
• When transporting and storing, keep cylinder secured in an upright position with cylinder valve turned off.
Keep cylinders ventilated and away from heat when in a vehicle.
• Liquid Petroleum Gas (LPG) is highly flammable and explosive. Flammable gas under pressure can cause a
fire or explosion if ignited.
• In any petroleum gas fire, flames should not be extinguished unless the fuel supply valve is turned OFF. If a
fire is extinguished and a supply of fuel is not turned OFF, an explosion hazard could be created.
• RISK OF BURNS. Contact with liquid contents of cylinder will cause freeze burns to the skin. If liquid con-
tents contacts skin or eyes, seek immediate medical attention.
• When exchanging LPG cylinders, be sure the cylinder valve is of the same type.
WARNING: If using gasoline, the LPG tank must be shut OFF. If using LPG, the fuel valve on the genera-
tor must be turned to OFF position.
FUEL OPTION B: LIQUID PETROLEUM GAS (LPG)
NOTE: LPG regulator inlet pressure is approximately 30 PSI at 0 °F, and 218 PSI at 100 °F.
• You can use LPG tanks with Type 1, right hand Acme threads with this generator. Verify that the qualification date
on tank has not expired. Do not use rusted or damaged cylinders.
• All new cylinders must be purged of air and moisture prior to filling. Used cylinders that have not been plugged or
kept closed must also be purged.
• The purging process should be done by the propane gas supplier. (Cylinders from an exchange supplier should
have been purged and properly filled by supplier).
Follow the instruction on the next page for connecting your generator to an LPG cylinder.
15
GENERATOR PREPARATION
FUEL OPTION B: LIQUID PETROLEUM GAS (LPG) - CONTINUED
To connect your generator to an LPG cylinder:
1. Take off the safety caps from the cylinder valve, generator mounted
regulator, and regulator connecting hose ends.
2. With the LPG tank closed, attach the LPG regulator connecting hose
into the valve. Turn the plastic coupling from the hose right (clock-
wise) to tighten hose assembly onto the LPG tank (Fig. 6).
3. Connect the opposite regulator connecting hose end to the genera-
tor’s LPG primary regulator with a 3/4 in. (19mm) wrench (not sup-
plied) (Fig. 7).
4. Turn the LPG tank valve ON (Fig. 8) and check for leaks by spraying
soapy water to check connections. If bubbles appear, become larger
in size, or increase in number, a leak exists. This MUST be corrected
before using generator. Contact your local Independent Authorized
Service Dealer (IASD) for assistance.
NOTE: You can use Teflon (or other tape) to secure the connection of
the LPG hose to your generator.
CAUTION: Always position the LPG cylinder so the connection be-
tween the valve and regulator won’t cause sharp bends or kinks in
hose.
WARNING: Risk of burns. Contact with liquid contents of cyl-
inder will cause freeze burns to the skin. If liquid contents contacts
skin or eyes, seek immediate medical attention.
WARNING: When transporting and storing, keep cylinder se-
cured in an upright position with cylinder valve turned off. Keep
cylinders ventilated and away from heat when in a vehicle.
Fig. 6
Fig. 7
Fig. 8
16
STEP 3: CONNECT THE BATTERY
Connecting/disconnecting the battery’s negative terminal requires removing the right wheel. Follow the instructions
below to connect the battery’s negative terminal.
NOTE: When using gasoline to run the generator, the battery must be connected whether using electric or recoil
start. The battery must also be connected for electric start when using LPG, but the battery does not need to be
connected for recoil start on LPG.
To connect the battery:
1. Remove the cover from the negative (-) battery terminal.
2. Connect the black cable to the negative (-) battery terminal with the suitable nuts and bolts.
3. Make sure connections are secure and slide rubber boot over the negative (-) battery terminal and connection
hardware.
4. Check that the positive (+) battery terminal has been pre-connected properly.
GENERATOR PREPARATION
WARNING: BATTERY GIVES OFF EXPLOSIVE HYDROGEN GAS.
• Keep battery away from spark, flame, or cigarette.
• Do not connect or disconnect battery while generator is running.
• Service or use battery only in well ventilated areas.
WARNING: Battery contains sulfuric acid. Battery acid is poisonous. Tilting the generator with the battery
installed can cause battery acid to spill.
• Wear protective clothing and eye wear when servicing battery.
• Keep out of reach of children.
• Do not tilt generator with battery installed.
• If battery acid gets on your skin, wash with water immediately.
• If battery acid gets in your eyes, flush with water for at least 15 minutes and call a doctor immediately.
If battery acid is swallowed, call a doctor immediately. Drink a large amount of water or milk. Then drink milk
of magnesia or vegetable oil.
IMPORTANT: If you do not plan to use the generator for an extended period of time, it is recommended to
DISCONNECT the battery cable from the battery terminal to protect the battery from losing charge. After discon-
necting the cable, cover the free end with an insulator such as electrical tape.
17
GENERATOR PREPARATION
After completing the above preparation, the generator is ready to be started.
STEP 4 - GROUND THE GENERATOR
To reduce the risk of electric shock and to maximize safety, the gen-
erator should be properly grounded.
Ground the generator by tightening the grounding nut on the front
control panel (Fig. 9) against a grounding wire. A generally acceptable
grounding wire is a No. 12 AWG (American Wire Gauge) stranded
copper wire.
This grounding wire should be connected at the other end to a cop-
per, brass, or steel-grounding rod that is driven into the earth. Wire
and grounding rods are not included with the generator.
NOTE: Grounding codes can vary by location. Contact a local electri-
cian to check the area codes.
WARNING: Failure to properly ground the generator increases your risk of electric shock.
HIGH ALTITUDE OPERATION ABOVE 2000 FEET
The fuel system on this generator may be affected by operation at high altitudes. Proper operation can be ensured by
installing an altitude kit at altitudes higher than 2000 feet above sea level. At elevations above 7000 feet, the engine
may experience a decrease in performance, even with the proper altitude kit. Operating this generator without said
kit may increase the engine’s emissions and decrease both fuel economy and performance.
This kit should be installed by a qualified mechanic. You can order the kit at wenproducts.com by searching part
number DF475-HA27. Refer to the instructions included with your altitude kit for more information about installa-
tion.
WARNING: To prevent serious injury from fire, follow the kit installation procedures in a well-ventilated
area away from ignition sources. If the engine is hot from use, shut the engine off and wait for it to cool before
proceeding. Do not smoke near the generator. Warranty will be void if adjustments are not made for high altitude
use.
CAUTION: Engines with the high-altitude kit installed operated at lower altitudes could cause severe engine
damage and affect emissions compliance. Be sure to UNINSTALL the high altitude kit when operating at altitudes
below 2000 feet.
Grounding Nut
Fig. 9
18
STARTING THE GENERATOR
To maximize safety, ALWAYS ground the generator before using it (see the “GROUND THE GENERATOR” section
on page 18).
Use a ground fault circuit interrupter (GFCI) in highly conductive areas such as metal decking or steel work. GFCIs
are available in-line with some extension cords.
CAUTION: Disconnect all electrical loads from the generator before attempting to start.
DANGER: CARBON MONOXIDE
Using a generator indoors CAN KILL YOU IN MINUTES. Generator exhaust contains carbon monoxide (CO). This
is a poison gas you cannot see or smell. If you can smell the generator exhaust, you are breathing CO. But even
if you cannot smell the exhaust, you could be breathing CO.
NEVER use a generator inside homes, garages, crawl spaces, or other partially enclosed areas. Deadly levels
of carbon monoxide can build up in these areas. Using a fan or opening windows and doors does NOT supply
enough fresh air. ONLY use a generator OUTSIDE and far away from windows, doors, and vents. These openings
can pull in generator exhaust.
Even if you use a generator correctly, CO may leak into the home. ALWAYS use a battery-powered or battery-
backup CO alarm in the home. If you start to feel sick, dizzy, or weak after the generator has been running, move
to fresh air RIGHT AWAY. See a doctor. You may have carbon monoxide poisoning.
WARNING: The exhaust from this product contains chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
WARNING: DO NOT operate generator near open flame or flammable materials This generator may emit
highly flammable and explosive gasoline vapors, which can cause severe burns or even death if ignited. A nearby
open flame can lead to explosion even if it isn’t directly in contact with gasoline. Do not smoke near the genera-
tor.
WARNING: This generator produces powerful voltage, which can result in electrocution.
WARNING: Do not use in rainy or wet conditions. Do not touch bare wires or receptacles (outlets). Do not
allow children or non-qualified persons to operate.
WARNING: Generator should ONLY be connected to electrical devices, either directly or with an extension
cord. NEVER CONNECT TO A BUILDING ELECTRICAL SYSTEM without a qualified electrician and connected to
a transfer switch as a separately derived system. Such connections must comply with local electrical laws and
codes. Failure to comply can create a back-feed, which may result in serious injury or death to utility workers.
Before starting the generator, make sure you have read and performed the steps in the “GENERATOR PREPARA-
TION” section of this manual. If you are unsure about how to perform any of the steps in this manual please call
1-847-429-9263 M-F 8-5 CST for customer service.
19
STARTING THE GENERATOR
STARTING THE GENERATOR
1. To use gasoline, turn the fuel valve to the ON position.
To use LPG, make sure all of the LPG connectors and hoses are well connected
and sealed. Close the fuel valve, then open the LPG tank valve.
2. Move the choke lever to the CLOSE/START position.
BEFORE STARTING THE GENERATOR
1. Verify that the generator is outside on a dry, level surface. Allow at least two feet of clearance on all sides of the
generator.
2. To maximize safety, check that the generator is properly grounded (see “GROUND THE GENERATOR”).
3. Check there is sufficient level of oil in the crankcase. Add oil if necessary (see “ADD/CHECK OIL”).
4. Verify the fuel selection dial is turned to the desired fuel. Turn the dial up to 12 o’clock position for gasoline and
down to 6 o’clock position for LPG. Check that there is adequate supply of the selected fuel.
5. Make sure all electrical devices are unplugged from the generator during ignition. Otherwise it will be difficult for
the engine to start.
a. To start the engine with electric starter:
3. Insert the key and turn the engine switch to the
START position for 2-3 seconds. NOTE: If the engine
does not start, release the switch and try again. Keeping
the switch in the START position too long can damage
the starter.
4. When engine starts, release the switch to the ON.
5. Slowly move choke lever to the OPEN/RUN posi-
tion. If engine fires, but does not continue to run, move
choke lever to CLOSE/START position and repeat start-
ing instructions.
b. To start the engine with recoil starter:
3. Turn the engine switch to the ON position.
4. Pull on the recoil starter handle slowly until a slight
resistance is felt, then pull quickly to start the engine.
Return cord gently into the recoil starter. Never allow
the cord to snap back.
If engine fails to start, repeat this step.
5. Once the engine has started, slowly return the choke
lever all the way to the OPEN/RUN position.
6. Allow the engine to run for several minutes before attempting to connect any electrical devices. This allows the
generator to stabilize its speed and temperature. Follow the instructions in the next section for properly connecting
your electrical devices.
NOTE: In case you have had repeated failed attempts to start the engine, please consult the troubleshooting guide
before attempting to start the generator. If problems persist please call 1-847-429-9263, M-F 8-5 CST.
WARNING: The LPG cylinder valve must be shut OFF when using gaso-
line. The generator’s fuel valve must be shut OFF when using LPG.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Wen DF475T User manual

Category
Power generators
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI