Page is loading ...
Rack Mounting Instructions
• Insert cage nuts (G) into the rack, six
on the front and four on the rear of
the rack.
• Mount the front of the sliders
(A & B) onto the rack with sunk head
screws (F), using a hex key N° 4.
• Fix the length of the sliders by
using a hex key N° 3.
• Mount the support bracket (C)
on the left and right front of
the device with two socket cap
screws (E) using a hex key N° 3.
• Mount the brackets onto the rack
by slightly lifting the device and
inserting the remaining screws
(H & I) using a Pozi screwdriver N° 3.
• Mount the rear of the sliders onto
the rack using a Pozi screwdriver
N° 3, using the rack mount screws
(I) and washers (H).
• Place and fix the sliding wheels
(D) with two socket cap screws (E)
on the left and right rear of the
device by using a hex key N° 3.
• Place the sliding wheels onto the
sliders and slide the device into
the rack.
INSTALL THE SLIDERS AND
DEVICE INTO THE RACK
1
2
4
6
3
5
7
These instructions are
valid for a standard
19” rack, using 3
mounting holes per
rack unit (1U).
!
You can configure settings using the Front Panel, the Graphical User
Interface (GUI) or the Command Line Interface (CLI).
To configure and save settings via GUI and CLI, please refer to
www.newtec.eu/support/documentation
• Insert the power cable to start the device.
• Wait for the menu tree to display.
• Select Mgmt Itf from the corresponding soft button.
• Navigate to IP Address.
• Press OK (to unfold the branch).
• Navigate to Mgmt1.
• Press OK.
• Navigate to IP Address/prefix and press OK.
• Use the Soft Buttons to enter a new IP Address/prefix.
• Press OK to confirm the setting.
• Now connect the Ethernet cable to Mgmt1 on the back panel.
• Now you can access the device from a management PC.
Congure your Device
The only way to shut down the device is to disconnect
the power cable from the power connector. Therefore
make sure that the power cable is accessible and not
obstructed when the device is operational.
Please save to fix your configured settings.
SET THE MANAGEMENT IP ADDRESS
SET DATE AND TIME
CONFIGURE AND SAVE
Display Navigate Buttons
Soft Buttons Escape OK
!
!
• Select Device from the corresponding soft button.
• Navigate to Date and Time.
• Press OK (to unfold the branch).
• Navigate to Date or Time and press OK.
• Use the navigation down button to display numerical values.
• Use the Soft Buttons to enter a new Date or Time.
• Press OK to confirm the settings.
To save settings via the Front Panel:
• Use the Soft Button Arrow and navigate completely to the right of
the root menu pane and select Actions.
• Navigate to Device Configuration Save and press OK.
• Select the configuration file name and Press OK to save the
configuration.
M6100
MDM6100
MDM6000
MCD6000
QUICK START GUIDE
Box Content
Safety & Cautions
Slider Kit Content
Item Quantity
Device 1
Slider Kit 1
Power Cable 1
QDR-report 1
Soft Copy Documentation 1
Hard Copy Documentation (optional) 1
6
16
16
C
10x
2x 8x
2x 4x2x 8x
1x RIGHT
1x LEFT
Hex Key size n°3
•
Hex Key size n°4
•
Pozi screwdriver
•
Size 3 (min size 2)
E
D
F
G
I
H
A
B
Required tools
Material in the box
Please read the Safety & Cautions section of the User Manual
(available on www.newtec.eu/support/documentation)
before you install and use this equipment.
!
Newtec’s training programs are designed to keep you up-to-date on the
latest Newtec products and technologies and have the confidence and
experience to install, configure, manage and troubleshoot our equipment.
TRAINING CALENDAR
For a list of public trainings, please refer to
www.newtec.eu/services-training
For pricing of tailor-made trainings or on-site training,
please contact [email protected]
Technical Support
CONTACT CUSTOMER SUPPORT
Newtec provides you with the expert technical support through our
Business Partners and our Support Centers worldwide.
If you encounter any issue on a product or you have a technical question,
please contact our Business Partner or use our Service Desk tool
customersupport.newtec.eu
DIAGNOSTIC REPORT
For effective support Newtec advices you to generate a diagnostic report out
of the equipment and provide it when raising a ticket to Customer Support.
For the procedure please refer to: www.newtec.eu/support
HOW TO UPGRADE THE SOFTWARE?
For the procedure please refer to: www.newtec.eu/support
HOW TO OBTAIN A SOFTWARE OR CAPABILITIES UPGRADE?
To obtain a software or capabilities upgrade,
please contact your Account Manager.
3
Training ServiceS
For an up-to-date calendar of our
Public Trainings, visit ou r website
(www.newtec.eu/tra ining) or contact us
via email (traini ng@newt ec.eu) to learn
more about Customer Trainings and
Tailor-Made Trainings.
Tom Paridaens
Training Operations M anager
TeCHnOLOgY Tr ainings
1. Satellite Communications 2 days Basic Level p. 4
2. Link Budget Calculation 2 days Advanced Level p. 5
3. Earth Station Design 4 days Advanced Leve l p. 6
saTeLLiTe aPPLiCaTiOns Trainings
1. VSAT Technology & Installation 1 day Basic Level p. 7
2. IP Trunking Certification Track 5 days Advanced Level p. 8
3. Broadcast & DSNG 2 days Advan ced Level p. 9
4. Redundancy Switching 0,5 day Advanced Level p. 10
5. Newtec IP Acceleration Solutions 2 days Advanced Level p. 11
newtec_training_148x210.indd 3 30/08/12 11:52
Training
CenTer
Portfolio
newtec_training_148x210.indd 1 30/08/12 11:52
8
Training ServiceS
IP Trunking Certification Track
This track is designed for Operators a nd
installers of IP Trun king Networks. Th e
training track brings you to t he world of
IP Trunking over Satel lite. The track wil l
give you the knowledge to design your
own Point-to-Point or Point-to-Multipoint
satellite IP Trunki ng Network. In 5 days
you will learn every thing you need to k now
about IP trunking:
MODULE 1*: IP TRUNKING
FUNDAMENTALS
IP Essentials for Satellite
Communication
IP over Satellite Network
Design: Point to Point
SATELLITE APPLICATIONS
TRAINING
MODULE 2:
IP TRUNKING ADVANCED
IP over Satellite Network
Design: Point to Multipoint
Trac Shaping & Acceleration
IP FlexACM Trunking & iDSNG
MODULE 3*:
IP TRUNKING BANDWIDTH
OPTIMISATION
FlexACM
NoDE: Noise and Distortion
Estimator Tool
Equalink: Linear and
Non-Linear Predistortion
Clear Channel Technology
Bandwidth Cancellation
* These modules can be followed as a
separate course.
newtec_training_148x210.indd 8 30/08/12 11:52
Training
serviCes
Newtec’s Training Center offers a w ide
variety of training co urses covering
Satellite Technology and Application s,
ensuring that you are kept up-to-d ate with
the latest technologies and to help you
advance your business. We invite you to
browse through this train ing portfolio to
learn more about their specific conte nt.
Newtec offers three types o f trainings :
1. Public Trainings
catalogue trainings ava ilable for everyone
and organised at Newtec Headquar ters
2. cusTomer Trainings
private catalogue traini ngs,
organised wherever you want
3. Tailor-made Trainings
private customized trai nings,
organised wherever you want
Our trainers are highly
experienced in their field and
receive satisfaction rates
of 90% and more.
Newtec is a certified
GVF training reseller
newtec_training_148x210.indd 2 30/08/12 11:52
Manuals
To obtain the latest device manuals, application notes and other product
documentation, please refer to www.newtec.eu/support/documentation
Training
NEWTEC’S TRAINING
CENTER OFFERS A
WIDE VARIETY OF
TRAINING COURSES,
BOTH PUBLIC AND
TAILOR-MADE
Get More Out of Your Equipment
The understanding of your application in combination with our
products leads to reliable and cost-efficient solutions.
APPLICATIONS
Visit: www.newtec.eu/applications
for our full application range.
This guide is provided for information purposes only.
The details contained in this document, including product and feature specifications,
are subject to change without notice and shall not bind Newtec in any way.
Visit our website: www.newtec.eu
Europe North-America South-America
Tel: +32 3 780 65 00 Tel: +1 203 323-0042 Tel: +55 11 2092 6220
Fax: +32 3 780 65 49 Fax: +1 203 323-8406 Fax: +55 11 2093 3756
Asia-Pacic China MENA
Tel: +65 6777 22 08 Tel: +86 10-823 18 730 Tel: +971 4 390 18 78
Fax: +65 6777 08 87 Fax: +86 10-823 18 731 Fax: +971 4 368 67 68
Shaping the Future of Satellite Communications
Feedback on this document Ref. 36185_01 – 04.2013
Please provide any comment, error found or suggestion
for improvement, you may have about this document to
Youtube.com/NewtecSatcom
Slideshare.net/newtec_satcom
Twier.com/Newtec_Satcom
Linkedin.com/company/newtec
Follow us
in
You
Tube
Register your Care Pack now!
Thank you for choosing Care Pack.
By registering your Care Pack on www.newtec.eu/support and
telling us who the end user of the unit is, we will be able to provide
valued Care Pack support. Moreover the end user will receive an
early notification on availability of new Software
updates/upgrades.
How to order a Care Pack?
Care Pack is to be ordered as a service option along with your Newtec
equipment.
In case you don’t have the Care Pack option on your equipment,
you can still order it up to six months after purchase date.
To order a Care Pack, please contact your Account Manager.
Need Additional Services?
Newtec offers higher levels of support (also on top of Care Pack) in order to
meet your services requirements (e.g. 24/7 technical support, assistance for
configuration or advanced hardware replacement).
Care Plan is a customized service contract protecting your installed base.
Information and pricing for service contracts can be provided on request on
/
