Bake Max BMPME20 Operating instructions

BMPME20

20 Qt Encore Planetary Mixer

Operation Manual

The BakeMax® Endurance Planetary Mixer provides durability, long life and

excellent mixing performance, all with an affordable price tag. They are safe,

easy to use and capable of a broad range of dough and food mixing applications.

Operation & Function

 Standard power supply 120 V/ 60 HZ. Nema 5-15P (Please use a plug with 3 wide

contacts and good grounding.)

 Installation of Mixer: Put the mixer attachment (#3) into the planetary shaft #2 and rotate

it in clockwise direction.

 Starting Procedure: Pull the gear change hand lever (#1) to position 1 before starting;

close the safety guard and then turn on the power switch (#5).

 Changing Speeds: Ensure the mixer is turned off before changing speeds. If the mixer is

turned on while changing gears you will damage the unit.

 Installation procedures for meat grinder and vegetable attachment: Ensure the

machine is turned off before starting, loosen the stud bolt and lift the top cover of its

head (#9). Then put on the attachment and tighten the stud bolt. Only use on the 1

st

speed as using a higher speed can damage the mixer.

 Shutting Down: When the operation is completed, turn off the power switch (#5) first,

then pull the gear change hand lever (#1) to position 1, and pull back the bowl lift handle

(#6) to the lowest point and finally disconnect power supply.

NOTES:

 The power socket must be provided with a good ground wire to guarantee the

mixer is grounded properly. There will be an electric shock if there is no ground

wire or if it is improperly mounted. Never connect the ground wire to gas pipes,

water pipes, lightning rods or telephone lines. Electric leakage should be

checked after installation. If the power line is damaged, it must be replaced by a

Service Company.

 Moving agitator in bowl. Keep hands, clothing and utensils out of bowl while in

operation. Do not use without interlocked safety guard. Do not put your hand into the

stirring barrel during operation. Disconnect the power supply before the installation of

the mixer.

 Power supply should be disconnected before installing the mixer.

 Don't operate the mixer beyond the time limit or overload its capacity to prevent

reduction of its service life.

 The mixer should be mounted on a stable and clean place. Keep it away from heat or

wet places and away from equipment which has strong electromagnet or can produce

strong electromagnet.

 Keep the machine clean constantly. Disconnect power supply before maintenance.

Clean machine with a soft damp cloth. Do not clean it with water spray or use harsh

detergents.

Warning!

Please have all service work completed by a professional service company.

Troubleshooting Guide:

WARNING

Ensure your recipe meets the mixers capacity.

Ensure water is 70 degrees Fahrenheit or reduce capacity.

Ensure Flour is at room temperature.

Ensure mixer is turned off when changing gears

Failure to comply with these warnings will void warranty.

BMPME20

SER.NO.

PART.NO.

PART NAME

SER.NO

.

PART.NO.

PART NAME

1

SM20-0I-19

Top cover

40

SM20-01-12

Gear shaft

2

GB54

Nut

41

SM20-01-03

Case

3

GB97.1

Clamp plate

42

SM20-01-06

Worm wheel

4

SM20-01-15

Pressing plate

43

GB119

5

SM20-01-07

Transmission shaft

support

44

SM20-DQ-09

Motor

6

SM20-0I-14

Spacer-lower

45

SM20-0I-02

Back housing

7

SM20-01-13

Taper gear wheel I

46

SM20-01-01

Back Cover

8

SM20-01-18-01

Tooth gear

47

SM20-0I-25

Plug

9

SM20-0I-18-02

Gear

48

SM20-01-38

Locking bolt

10

SM20-01-20

Gear

49

SM20-0I-24

Attachment hub

11

SM20-01-21

Bushing

50

SM20-0I-26

Ring

12

SM20-01-22

Sleeve

51

SM20-01-23

Taper gear wheel 2

13

SM20-01-I6

Main shaft

52

SM20-01-30

Front housing

14

SM20-01-44

Plunger-shifter yoke

53

SM20-01-32

Internal gear

15

SM20-01-43

Spring

54

SM20-01-34

Hood ring

16

SM20-0I-42

Retainer-spring

55

SM20-06-01

Flat Beater

17

SM20-01-2I

Bushing

56

SM20-04-00

Bowl assembly

18

201

Bearing

57

GB591.1

Nut

19

SM20-01-09

Shaft worm gear

58

SM20-01-33

Gear

20

SM20-01-08

Gear

59

203

Bearing

21

201

Bearing

60

SM20-01-35

Operating shelf

22

SM20-01-27

Claw type gear

wheel

61

SM20-01-36

Working shaft

23

205

Bearing

62

204

Bearing

24

HG-692

Oil seal

63

HG4-692

Oil seal

25

GB54

Nut

64

SM20-01-39-01

Cam-gear shifter

26

GB54

Nut

65

SM20-01-39-02

Plate-shifter index

27

201

Bearing

66

SM20-01-39-04

Handle-shifter

28

SM20-06-02

Wire whip

67

SM20-05-01

Stud

24

SM20-01-11

Gear

68

SM20-05-12

Crank lever

30

SM20-01-05

Bushing

69

SM20-05-11

Connecting rod

31

SM20-01-04

Gear

70

SM20-05-13

Lift handle

32

201

Bearing

71

GB97.1

Ring

33

SM20-06-03

Spiral dough hook

72

GB97.1

Ring

34

SM20-01-44

Plunger-shifter yoke

73

SM20-05-10

Spring

35

SM20-01-43

Spring

74

Gb6171

Nut

36

SM20-01-42

Retainer Spring

(shifter yolk)

75

SM20-05-05

Support

37

SM20-01-41

Shifting yoke

76

SM20-05-06

Base

38

SM20-01-40

Declutch shift shaft

77

203

Bearing

39

GB6171

Nut

78

SM20-03-00

Safety guard

Bake Max BMPME20 Operating instructions

Bake Max BMPME20 Operating instructions

Related papers

Other documents