MagTek® Inc., 1710 Apollo Court, Seal Beach, CA 90740 | p 562-546-6400 | f 562-546-6301 | 800-788-6835 | www.magtek.com
oDynamo is a PCI PTS 5.x Certied Secure Card Reader (SCR) with SRED. oDynamo’s
enclosure and its associated electronics have been designed to form a Tamper
Resistant Security Module (TRSM). The covers are securely attached and incorporate
sensing circuits to detect if any attempt is made to open the device. Internal spaces
within the device have been minimized to reduce the possibility of unauthorized
modications. Any attempt to penetrate or modify oDynamo electronically will cause
the device to permanently erase its stored encryption keys, after which oDynamo will
cease to function. Following are the areas the user can check for tampering.
oDynamo
Device Inspection
Front
Visual Comparison
Carefully inspect the form factor. Make certain there are no additional electronics, wires or forms added to the device.
Check the overall form factor for signs of attempted entry.
Exterior Surface/Metal Bezel
Look for any hidden and additional
wires in crevasses, seams and
exterior surface of the device.
No additional wires should be on
the device. Observe front face of
the metal bezel and inspect for
any modication or hidden wires
coming out of the card slot or drain
holes. The device has a metal
bezel that is one die-cast piece.
Decal
The device includes a label well
around the General Status LED.
MagTek is default label.
General Status LED
Apply power to the device, LED
should be solid GREEN. Apply
power to the device for 60
seconds. If the LED shows any
red, a tamper event has occurred.
Card Insertion Slot
The card insertion slot is a
smooth, unobstructed path.
Insert an embossed card into
the device to check for any
signs of obstructions inside the
card insertion slot. Other than
the magnetic head that reads
magnetic stripes and contact
points that read chips there are
no electronics, objects or wires
on the path.
Dismount Switches
Exercise the two (2) dismount
switches by pressing them.
The switch should return to the
original position upon release
of nger pressure. They disable
the device in the event of
unauthorized removal.
Mounting Gasket
The device’s installation face
includes a gasket. Do not remove
the gasket.
PN D998200235 PAGE 1
Weight and Dimension
Weight: 1.76 lbs. (800g) Dimensions: 3.94 in. W x 2.80 in. H x 5.52 in. L
(100.1 mm x 71.1mm x 140.2mm)
MagTek, Inc. | www.magtek.com
Top Back
Carefully inspect the form factor. Make certain there are no additional electronics, wires or forms added to the device.
Crevasses
Look for any hidden and additional wires in crevasses,
seams and exterior surface of the device.
Screws
Check tampering of 6 screws. DO NOT REMOVE THE
SCREWS.
Connection Ports
Inspect individual connection
ports
• RS-232 and Power Port
• USB Host Port
• USB Device Port
• Ethernet Port
• Alternative Earth Grounding
Port
oDynamo | Device Inspection
Bottom Back
Carefully inspect the form factor. Make certain there are no additional electronics, wires or forms added to the device.
Screws
Check tampering of 4 screws.
DO NOT REMOVE THE
SCREWS.
Ventilation Holes
PRIOR TO INSTALLATION Inspect for objects or wires in
the vent holes.
Product Label
The product label is located on the back of the device.
Check PN, SN and HW number. Serial Number matches
serial number on boot-up.
PN D998200235 PAGE 2
MagTek, Inc. | www.magtek.com
oDynamo | Device Inspection
Left Side Angle
Carefully inspect the form factor. Make certain there are no additional electronics, wires or forms added to the device.
5 Drain Holes
Inspect the 4x drain holes below
the bezel nose (plus the 1x drain
hole to the left side of the bezel
nose). There are no electronics,
objects or wires coming from the
drain holes.
Right Side Angle
Carefully inspect the form factor. Make certain there are no additional electronics, wires or forms added to the device.
Crevasses
Inspect crevasses to
make certain there are no
extraneous wires.
Seams Parting Line
Inspect where the seams come
together to make certain there
are no extraneous wires.
Crevasses
Inspect crevasses to
make certain there are no
extraneous wires.
Seams Parting Line
Inspect where the seams come
together to make certain there
are no extraneous wires.
PN D998200235 PAGE 3
Founded in 1972, MagTek is a leading manufacturer of electronic systems for the reliable issuance, reading, transmission and security of cards, checks, PINs and identication
documents. Leading with innovation and engineering excellence, MagTek is known for quality and dependability. Its products include secure card reader/authenticators, token
generators, EMV contact, contactless and NFC reading devices, encrypting check scanners, PIN pads and distributed credential personalization systems for secure magstripe and
EMV enabled cards. These products are used worldwide by nancial institutions, retailers, and processors to provide secure and efcient payment and identication transactions.
Today, MagTek continues to innovate. Its MagneSafe™ Security Architecture leverages strong encryption, secure tokenization, dynamic card authentication, and device/host validation
enabling users to assess the trustworthiness of credentials and terminals used for online identication, payment processing, and high-value electronic transactions.
MagTek
®
Inc. | www.magtek.com | Registered to ISO 9001:2015 © Copyright 2018 MagTek, Inc. D998200235 rev 20 6/18
oDynamo | Device Inspection
At Point of Installation - Mounted
Device Audit
As part of your inspection it is helpful to do the following for
your device inspection audit.
• Be certain to have a list of the devices and include the
details listed on the asset tag.
• It may be helpful to take photos of the front, back, and
side of each device.
Be certain to check device Part numbers, serial numbers
and IDs and check physical connections. Report any
suspected signs of tampering immediately.
PCI compliance web page.
How to nd oDynamo on PCI web site https://www.pcise-
curitystandards.org/assessors_and_solutions/pin_trans-
action_devices. Search for MagTek and nd the product
name, oDynamo, on the web page. Compare the Hardware
# and Firmware #.
Periodically inspect the following items while installed:
Exterior surface/metal bezel
• Card slot
• Five (5) drain holes
• Form factor
• Crevasses
• Screws
Inspect the following additional items during service:
• Crevasses
• Screws
• Ventilation holes
• Connection ports
• Seams parting lines
Checklist Summary
Front Face Metal Bezel
Observe front face of the metal bezel and inspect for any
modication or hidden wires.
Mounting Holes
Look for any hidden and additional wires. No additional
wires should be coming out of the holes.
Carefully inspect the form factor. Make certain there are no additional electronics, wires or forms added to the device.
Periodically inspect the following items:
• Metal Bezel
• Card Slot
When servicing behind cabinet/door (terminal) inspect
device for external wires, or foreign objects not included
in the solution design. For proper installation, refer to your
solution design documentation.
PN D998200235 PAGE 4
Check views of front, bottom, top and back of the device and compare to photos.
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Magtek MT-85 Datasheet
-
-
-
-
-
-
-
-
-
