Toro 14-38Z TimeCutter Z Riding Mower User manual

Category
Lawnmowers
Type
User manual

This manual is also suitable for

Operators Manual
English (GB)
Form No. 3329–262
Z14–38 and Z16–42
TimeCutter
Z with Side Discharge Mower
Model No. 74402—Serial No. 230000001 and Up
Model No. 74403—Serial No. 230000001 and Up
2
All Rights Reserved
Printed in the USA
2003 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
This spark ignition system complies with Canadian
ICES-002.
Ce système d’allumage par étincelle de véhicule est
conforme à la norme NMB-002 du Canada.
Contents
Page
Introduction 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safe Operating Practices 3. . . . . . . . . . . . . . . . . . . .
Toro Riding Mower Safety 5. . . . . . . . . . . . . . . . . . .
Slope Chart 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety and Instruction Decals 9. . . . . . . . . . . . . . . . .
Gasoline and Oil 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Gasoline 12. . . . . . . . . . . . . . . . . . . . .
Using Stabilizer/Conditioner 12. . . . . . . . . . . . . . . . .
Filling the Fuel Tank 12. . . . . . . . . . . . . . . . . . . . . . .
Checking the Engine Oil Level 12. . . . . . . . . . . . . . .
Operation 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Think Safety First 13. . . . . . . . . . . . . . . . . . . . . . . . . .
Controls 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking Brake 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting and Stopping the Engine 13. . . . . . . . . . . . . .
Operating the Power Take Off (PTO) 14. . . . . . . . . .
The Safety Interlock System 14. . . . . . . . . . . . . . . . .
Testing the Safety Interlock System 14. . . . . . . . . . . .
Driving Forward or Backward 15. . . . . . . . . . . . . . . .
Stopping the Machine 15. . . . . . . . . . . . . . . . . . . . . .
Adjusting the Height of Cut 16. . . . . . . . . . . . . . . . . .
Adjusting the Mower Wheels (For Models 74330 and
74350 Only) 16. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Positioning the Seat 16. . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Motion Control Levers 17. . . . . . . . . .
Pushing the Machine by Hand 17. . . . . . . . . . . . . . . .
Adjusting the Footrest 17. . . . . . . . . . . . . . . . . . . . . .
Removing and Installing the Engine Hood 18. . . . . .
Side Discharge 18. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tips for Mowing Grass 19. . . . . . . . . . . . . . . . . . . . .
Maintenance 20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Maintenance Schedule 20. . . . . . . . .
Servicing the Engine Oil 21. . . . . . . . . . . . . . . . . . . .
Servicing the Air Cleaner 22. . . . . . . . . . . . . . . . . . . .
Servicing the Spark Plug 23. . . . . . . . . . . . . . . . . . . .
Servicing the Cutting Blades 24. . . . . . . . . . . . . . . . .
Greasing and Lubrication 26. . . . . . . . . . . . . . . . . . . .
Servicing the Battery 27. . . . . . . . . . . . . . . . . . . . . . .
Page
Draining the Fuel Tank 29. . . . . . . . . . . . . . . . . . . . . .
Replacing the Fuel Filter 29. . . . . . . . . . . . . . . . . . . .
Checking the Tire Pressure 29. . . . . . . . . . . . . . . . . .
Leveling the Mower from Side-to-Side 29. . . . . . . . .
Adjusting the Front-to-Rear Blade Slope 30. . . . . . . .
Inspecting the Belts 32. . . . . . . . . . . . . . . . . . . . . . . .
Replacing the Mower Belt 32. . . . . . . . . . . . . . . . . . .
Removing the Mower 32. . . . . . . . . . . . . . . . . . . . . . .
Installing the Mower 33. . . . . . . . . . . . . . . . . . . . . . .
Fuse 33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Washing the Underside of the Mower 33. . . . . . . . . .
Replacing the Grass Deflector 34. . . . . . . . . . . . . . . .
Wiring Diagram 35. . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning and Storage 36. . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Toro Total Coverage Guarantee 40. . . . . . . . . . . . . .
Introduction
Read this manual carefully to learn how to operate and
maintain your product properly. The information in this
manual can help you and others avoid injury and product
damage. Although Toro designs and produces safe
products, you are responsible for operating the product
properly and safely.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model and
serial numbers of your product ready. Figure 1 illustrates
the location of the model and serial numbers on the
product.
m–6414
1
Figure 1
1. Model and serial number plate
3
Write the product model and serial numbers in the space
below:
Model No.
Serial No.
This manual identifies potential hazards and has special
safety messages that help you and others avoid personal
injury and even death. Danger, Warning, and Caution are
signal words used to identify the level of hazard. However,
regardless of the hazard, be extremely careful.
Danger signals an extreme hazard that will cause serious
injury or death if you do not follow the recommended
precautions.
Warning signals a hazard that may cause serious injury or
death if you do not follow the recommended precautions.
Caution signals a hazard that may cause minor or moderate
injury if you do not follow the recommended precautions.
This manual uses two other words to highlight information.
Important calls attention to special mechanical
information and Note: emphasizes general information
worthy of special attention.
Safety
Safe Operation Practices for
Ride-on (riding) Rotary
Lawnmower Machines
This machine meets or exceeds European Standards in
effect at the time of production. However, improper use
or maintenance by the operator or owner can result in
injury. To reduce the potential for injury, comply with
these safety instructions and always pay attention to the
safety alert
symbol, which means CAUTION,
WARNING, or DANGER—“personal safety
instruction.” Failure to comply with the instruction may
result in personal injury or death.
Safe Operating Practices
The following instructions are from the CEN standard EN
836:1997.
This product is capable of amputating hands and feet and
throwing objects. Always follow all safety instructions to
avoid serious injury or death.
Training
Read the instructions carefully. Be familiar with the
controls and the proper use of the equipment.
Never allow children or people unfamiliar with these
instructions to use the lawnmower. Local regulations
can restrict the age of the operator.
Never mow while people, especially children, or pets
are nearby.
Keep in mind that the operator or user is responsible for
accidents or hazards occurring to other people or their
property.
Do not carry passengers.
All drivers should seek and obtain professional and
practical instruction. Such instruction should
emphasize:
the need for care and concentration when working
with ride-on machines;
control of a ride-on machine sliding on a slope will
not be regained by the application of the control
levers. The main reasons for loss of control are:
insufficient wheel grip, especially on wet grass;
being driven too fast;
inadequate braking;
the type of machine is unsuitable for its task;
lack of awareness of the effect of ground
conditions, especially slopes;
incorrect hitching and load distribution.
Preparation
While mowing, always wear substantial footwear and
long trousers. Do not operate the equipment when
barefoot or wearing open sandals.
Thoroughly inspect the area where the equipment is to
be used and remove all objects which may be thrown by
the machine.
Warning—Fuel is highly flammable.
Store fuel in containers specifically designed for this
purpose.
Refuel outdoors only and do not smoke while
refuelling.
Add fuel before starting the engine. Never remove
the cap of the fuel tank or add fuel while the engine
is running or when the engine is hot.
4
If fuel is spilled, do not attempt to start the engine
but move the machine away from the area of
spillage and avoid creating any source of ignition
until fuel vapors have dissipated.
Replace all fuel tanks and container caps securely.
Replace faulty silencers.
Before using, always visually inspect to see that the
blades, blade bolts and cutter assembly are not worn or
damaged. Replace worn or damaged blades and bolts in
sets to preserve balance.
On multi-bladed machines, take care as rotating one
blade can cause other blades to rotate.
Operation
Be alert, slow down and use caution when making
turns. Look behind and to the side before changing
directions.
Do not operate the engine in a confined space where
dangerous carbon monoxide fumes can collect.
Mow only in daylight or in good artificial light.
Before attempting to start the engine, disengage all
blade attachment clutches and shift into neutral.
Do not use on slopes greater than 12–1/2 degrees.
Remember there is no such thing as a safe slope. Travel
on grass slopes requires particular care. To guard
against overturning:
do not stop or start suddenly when on a slope;
use slow speeds on slopes and during tight turns;
stay alert for humps and hollows and other hidden
hazards;
Use care when pulling loads or using heavy equipment.
Use only approved drawbar hitch points.
Limit loads to those you can safely control.
Do not turn sharply. Use care when reversing.
Watch out for traffic when crossing or near roadways.
Stop the blades rotating before crossing surfaces other
than grass.
When using any attachments, never direct discharge of
material toward bystanders nor allow anyone near the
machine while in operation.
Never operate the machine with damaged guards or
without safety protective devices in place.
Do not change the engine governor settings or
overspeed the engine. Operating the engine at excessive
speed can increase the hazard of personal injury.
Before leaving the operators position:
disengage the power take-off and lower the
attachments;
change into neutral and set the parking brake;
stop the engine and remove the key.
Disengage drive to attachments, stop the engine, and
disconnect the spark plug wire(s) or remove the ignition
key
before clearing blockages or unclogging chute;
before checking, cleaning or working on the
lawnmower;
after striking a foreign object. Inspect the
lawnmower for damage and make repairs before
restarting and operating the equipment;
if the machine starts to vibrate abnormally (check
immediately).
Disengage drive to attachments when transporting or
not in use.
Stop the engine and disengage drive to attachment
before refuelling;
before removing the grass catcher;
before making height adjustment unless adjustment
can be made from the operators position.
Reduce the throttle setting during engine run-out and, if
the engine is provided with a shut-off valve, turn the
fuel off at the conclusion of mowing.
Maintenance and Storage
Keep all nuts, bolts and screws tight to be sure the
equipment is in safe working condition.
Never store the equipment with fuel in the tank inside a
building where fumes can reach an open flame or spark.
Allow the engine to cool before storing in any
enclosure.
To reduce the fire hazard, keep the engine, silencer,
battery compartment and fuel storage area free of grass,
leaves, or excessive grease.
Check the grass catcher frequently for wear or
deterioration.
Replace worn or damaged parts for safety.
If the fuel tank has to be drained, this should be done
outdoors.
On multi-bladed machines, take care as rotating one
blade can cause other blades to rotate.
5
When machine is to be parked, stored or left
unattended, lower the cutting means unless a positive
mechanical lock is used.
Toro Riding Mower Safety
The following list contains safety information specific to
Toro products or other safety information that you must
know that is not included in the CEN standard.
Engine exhaust contains carbon monoxide, which is an
odorless, deadly poison that can kill you. Do not run
engine indoors or in an enclosed area.
Keep hands, feet, hair and loose clothing away from
attachment discharge area, underside of mower and any
moving parts while engine is running.
Do not touch equipment or attachment parts which may
be hot from operation. Allow to cool before attempting
to maintain, adjust, or service.
Battery acid is poisonous and can cause burns. Avoid
contact with skin, eyes and clothing. Protect your face,
eyes, and clothing when working with a battery.
Battery gases can explode. Keep cigarettes, sparks and
flames away from battery.
Use only genuine Toro replacement parts to ensure that
original standards are maintained.
Use only Toro-approved attachments. Warranty may be
voided if used with unapproved attachments.
Slope Operation
Do not mow slopes greater than 12–1/2 degrees.
Do not mow near drop–offs, ditches, steep banks or
water. Wheels dropping over edges can cause rollovers,
which may result in serious injury, death or drowning.
Do not mow slopes when grass is wet. Slippery
conditions reduce traction and could cause sliding and
loss of control.
Do not make sudden turns or rapid speed changes.
Use a walk behind mower and/or a hand trimmer near
drop–offs, ditches, steep banks or water.
Reduce speed and use extreme caution on slopes.
Remove or mark obstacles such as rocks, tree limbs,
etc. from the mowing area. Tall grass can hide
obstacles.
Watch for ditches, holes, rocks, dips, and rises that
change the operating angle, as rough terrain could
overturn the machine.
Avoid sudden starts when mowing uphill because the
mower may tip backwards.
Be aware that loss of traction may occur going
downhill. Weight transfer to the front wheels may cause
drive wheels to slip and cause loss of braking and
steering.
Always avoid sudden starting or stopping on a slope. If
tires lose traction, disengage the blades and proceed
slowly off the slope.
Follow the manufacturers recommendations for wheel
weights or counterweights to improve stability.
Use extreme care with grass catchers or other
attachments. These can change the stability of the
machine and cause loss of control.
6
Sound Pressure for
Model 74402
This unit has a maximum sound pressure level at the
operators ear of 86 dBA, based on measurements of
identical machines per Directive 98/37/EC.
Sound Power for Model 74402
This unit has a guaranteed sound power level of 100 dBA,
based on measurements of identical machines per Directive
2000/14/EC.
Vibration for Model 74402
This unit does not exceed a hand/arm vibration level of
3.22 m/s
2
, based on measurements of identical machines
per Directive 98/37/EC.
This unit does not exceed a whole body vibration level of
.195 m/s
2
, based on measurements of identical machines
per Directive 98/37/EC.
Sound Pressure for
Model 74403
This unit has a maximum sound pressure level at the
operators ear of 87 dBA, based on measurements of
identical machines per Directive 98/37/EC.
Sound Power for Model 74403
This unit has a guaranteed sound power level of 100 dBA,
based on measurements of identical machines per Directive
2000/14/EC.
Vibration for Model 74403
This unit does not exceed a hand/arm vibration level of
4.66 m/s
2
, based on measurements of identical machines
per Directive 98/37/EC.
This unit does not exceed a whole body vibration level of
.14 m/s
2
, based on measurements of identical machines per
Directive 98/37/EC.
7
Slope Chart
8
9
Safety and Instruction Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or lost.
93-6677
1. Warning—do not operate
the mower with the
deflector up or removed;
keep the deflector in
place.
2. Cutting/dismemberment
hazard of hand or foot,
mower blade—stay away
from moving parts.
93-7009
1. Warning—do not operate the mower with the deflector up or
removed; keep the deflector in place.
2. Cutting/dismemberment hazard of hand or foot, mower
blade—stay away from moving parts.
93-7010
1. Thrown object hazard—stay a safe distance from the machine.
2. Thrown object hazard, mower—keep the deflector in place.
3. Cutting/dismemberment of hand or foot—stay away from
moving parts.
105-7015
106-2223
106-2224
1. Throttle
2. Choke
3. Fast
4. Continuous variable
setting
5. Slow
6. Power take-off (PTO)
7. Headlights
8. Engine—stop
9. Engine—run
10. Engine—start
11. Ignition
10
104-4163
1. Explosion hazard
2. No fire, open flames, or
smoking.
3. Caustic liquid/chemical
burn hazard
4. Wear eye protection
5. Read the
Operator’s
Manual.
6. Keep bystanders a safe
distance from the battery.
106-7043
1. Do not tow the machine; pull the lever out to ride on the
machine or push the lever in to push the machine.
106-8717
1. Read the instructions
before servicing or
performing maintenance.
2. Check tire pressure every
25 operating hours.
3. Grease every
25 operating hours.
4. Engine
106-6989
1. Warning—read the
instructions before servicing
or performing maintenance;
set the parking brake and
remove the ignition key
before leaving the machine.
2. Warning—read the
Operator’s Manual.
3. Thrown object hazard,
mower—keep the deflector
in place.
4. Tipping hazard, slopes
greater than 12.5
degrees—drive the machine
up and down the hill.
5. Thrown object hazard—keep
bystanders a safe distance
from the machine and pick
up debris before operating.
6. Crushing/dismemberment
hazard of bystanders—do
not carry passengers.
7. Cutting/dismemberment
hazard of hand or foot,
mower blade—stay away
from moving parts.
11
104-5091
1. Contains lead; do not
discard.
2. Recycle
3. Wear eye protection;
explosive gases can cause
blindness and other injuries
4. No sparks, flame, or
smoking
5. Sulfuric acid can cause
blindness or severe burns.
6. Flush eyes immediately with
water and get medical help
fast.
7. Maximum fill line
8. Minimum fill line
9. Instructions for activating the
battery
12
Gasoline and Oil
Recommended Gasoline
Use UNLEADED Regular Gasoline suitable for automotive
use (87 pump octane minimum). Leaded regular gasoline
may be used if unleaded regular is not available.
Important Never use methanol, gasoline containing
methanol, or gasohol containing more than 10% ethanol
because the fuel system could be damaged. Do not mix oil
with gasoline.
Danger
In certain conditions, gasoline is extremely
flammable and highly explosive. A fire or
explosion from gasoline can burn you and others
and can damage property.
Fill the fuel tank outdoors, in an open area,
when the engine is cold. Wipe up any gasoline
that spills.
Never fill the fuel tank inside an enclosed trailer.
Do not fill the fuel tank completely full. Add
gasoline to the fuel tank until the level is 1/4 to
1/2 inch (6 to 13 mm) below the bottom of the
filler neck. This empty space in the tank allows
gasoline to expand.
Never smoke when handling gasoline, and stay
away from an open flame or where gasoline
fumes may be ignited by a spark.
Store gasoline in an approved container and
keep it out of the reach of children. Never buy
more than a 30-day supply of gasoline.
Always place gasoline containers on the ground
away from your vehicle before filling.
Do not fill gasoline containers inside a vehicle or
on a truck or trailer bed because interior
carpets or plastic truck bed liners may insulate
the container and slow the loss of any static
charge.
When practical, remove gas–powered
equipment from the truck or trailer and refuel
the equipment with its wheels on the ground.
If this is not possible, then refuel such
equipment on a truck or trailer from a portable
container, rather than from a gasoline dispenser
nozzle.
If a gasoline dispenser nozzle must be used, keep
the nozzle in contact with the rim of the fuel
tank or container opening at all times until
fueling is complete.
Gasoline is harmful or fatal if swallowed.
Long–term exposure to vapors can cause serious
injury and illness.
Avoid prolonged breathing of vapors.
Keep face away from nozzle and gas tank or
conditioner opening.
Keep gas away from eyes and skin.
Warning
Using Stabilizer/Conditioner
Use a fuel stabilizer/conditioner in the machine to provide
the following benefits:
Keeps gasoline fresh during storage of 90 days or less.
For longer storage it is recommended that the fuel tank
be drained.
Cleans the engine while it runs
Eliminates gum-like varnish buildup in the fuel system,
which causes hard starting
Important Do not use fuel additives containing
methanol or ethanol.
Add the correct amount of gas stabilizer/conditioner to the
gas.
Note: A fuel stabilizer/conditioner is most effective when
mixed with fresh gasoline. To minimize the chance of
varnish deposits in the fuel system, use fuel stabilizer at all
times.
Filling the Fuel Tank
1. Shut the engine off and set the parking brake.
2. Clean around the fuel tank cap and remove the cap. Add
unleaded regular gasoline to the fuel tank until the level
is 1/4 to 1/2 inch (6 to 13 mm) below the bottom of the
filler neck. This space in the tank allows gasoline to
expand. Do not fill the fuel tank completely full.
3. Install the fuel tank cap securely. Wipe up any gasoline
that may have spilled.
Checking the Engine Oil Level
Before you start the engine and use the machine, check the
oil level in the engine crankcase; refer to Checking the Oil
Level, page 23.
13
Operation
Note: Determine the left and right sides of the machine
from the normal operating position.
Think Safety First
Please carefully read all of the safety instructions and
decals in the safety section. Knowing this information
could help you, your family, pets or bystanders avoid
injury.
Danger
Mowing on wet grass or steep slopes can cause
sliding and loss of control.
Wheels dropping over edges can cause rollovers,
which may result in serious injury, death or
drowning.
To avoid loss of control and possibility of rollover:
Do not mow near drop–offs or near water.
Do not mow slopes greater than 12.5 degrees.
Reduce speed and use extreme caution on slopes.
Avoid sudden turns or rapid speed changes.
2
3
1
m–6491
Figure 2
1. Safe Zone—use the
Timecutter here
2. Use walk behind mower
and/or hand trimmer near
drop–offs and water.
3. Water
Controls
Become familiar with all of the controls (Fig. 3 and 4)
before you start the engine and operate the machine.
m–6415
1
3
2
Figure 3
1. Ignition switch
2. Throttle/Choke
3. Power take off (PTO)
1 1
3
2
m–6416
3
Figure 4
1. Motion control lever
2. Height-of-cut lever
3. Armrests —Optional for
models 74402 and 74403
Parking Brake
The parking brake is automatically set when the motion
control levers are in the brake position (Fig. 9).
Always position the motion control levers into the brake
position when you stop the machine or leave it unattended.
14
Starting and Stopping the
Engine
Starting the Engine
1. Sit down on the seat and move the motion controls to
the brake position.
2. Move the PTO (power take off) to Off (Fig. 5).
1
m–4201
2
Figure 5
1. PTO—On 2. PTO—Off
3. Move the throttle lever to Choke before starting a cold
engine (Fig. 6).
Note: A warm or hot engine may not require choking.
4. Turn the ignition key to Start to energize the starter.
When the engine starts, release the key.
Important Do not engage the starter for more than
10 seconds at a time. If the engine fails to start, allow a
60 second cool-down period between attempts. Failure to
follow these instructions can burn out the starter motor.
5. After the engine starts, move the throttle lever to Fast
(Fig. 6). If the engine stalls or hesitates, move the
throttle lever back to Choke for a few seconds. Then
move the throttle lever to the desired setting. Repeat
this as required.
m–5126
4
3
2
1
Figure 6
1. Engine
2. Choke
3. Fast
4. Slow
m–4268
1
2
3
4
Figure 7
1. Off
2. Run
3. Start
4. Ignition
Stopping the Engine
1. Move the throttle lever to Fast (Fig. 6).
2. Move the PTO to Off (Fig. 5).
3. Turn the ignition key to Off (Fig. 7).
4. Pull the wire off of the spark plug(s) to prevent the
possibility of someone accidentally starting the machine
before transporting or storing the machine.
5. Close the fuel shut-off valve under the front of the fuel
tank before transporting or storing the machine.
Important Make sure the fuel shut-off valve is closed
before transporting or storing the machine, as fuel leakage
may occur.
Operating the Power Take Off
(PTO)
The power take off (PTO) switch engages and disengages
power to the electric clutch.
Engaging the PTO
1. Release pressure on the traction control levers and place
the machine in neutral.
2. Move the throttle to the Fast position.
3. Pull out on the PTO switch to engage it (Fig. 8).
15
1
m–4201
2
Figure 8
1. PTO—On 2. PTO—Off
Disengaging the PTO
Push the PTO switch to Off (Fig. 8).
The Safety Interlock System
If safety interlock switches are disconnected or
damaged the machine could operate unexpectedly
causing personal injury.
Do not tamper with the interlock switches.
Check the operation of the interlock switches
daily and replace any damaged switches before
operating the machine.
Caution
Understanding the Safety Interlock
System
The safety interlock system is designed to prevent the
engine from starting unless:
The PTO is disengaged.
The motion control levers are in the brake position.
The safety interlock system also is designed to stop the
engine when the control levers out of brake position and
you rise from the seat when the PTO is engaged.
Testing the Safety Interlock
System
Test the safety interlock system before you use the machine
each time. If the safety system does not operate as
described below, have an Authorized Service Dealer repair
the safety system immediately.
1. While sitting on the seat, with the control levers in
brake position, and move the PTO to On. Try starting
the engine; the engine should not crank.
2. While sitting on the seat, move the PTO to Off. Move
either motion control lever to the center, unlocked
position. Try starting the engine; the engine should not
crank. Repeat with the other motion control lever.
3. While sitting on the seat, move the PTO to Off, and
lock the motion control levers in neutral. Start the
engine. While the engine is running, move the motion
control levers to the center, unlocked position, engage
the PTO, and rise slightly from the seat; the engine
should stop.
Driving Forward or Backward
The throttle control regulates the engine speed as measured
in rpm (revolutions per minute). Place the throttle control in
the Fast position for best performance. Always operate in
the full throttle position.
The machine can spin very rapidly. The operator
may lose control of the machine and cause
personal injury or damage to the machine.
Use caution when making turns.
Slow the machine down before making sharp
turns.
Caution
Forward
1. Move the levers to the center, unlocked position.
2. To go forward, slowly push the motion control levers
forward (Fig. 9).
3
2
5
4
2
m–6466
1
Figure 9
1. Motion control lever
2. Center unlock position
3. Forward
4. Backward
5. Brake position
16
To go straight, apply equal pressure to both motion control
levers (Fig. 9).
To turn, release pressure on the motion control lever toward
the direction you want to turn (Fig. 9).
The farther you move the traction control levers in either
direction, the faster the machine will move in that direction.
To stop, pull the motion control levers to neutral.
Backward
1. Move the levers to the center, unlocked position.
2. To go backward, slowly pull the motion control levers
rearward (Fig. 9).
To go straight, apply equal pressure to both motion control
levers (Fig. 9).
To turn, release the pressure on the motion control lever
toward the direction you want to turn (Fig. 9).
To stop, push the motion control levers to neutral.
Stopping the Machine
To stop the machine, move the traction control levers to
neutral and separate to the brake position, disengage the
PTO, ensure the throttle is in the fast position, and turn the
ignition key to off. Remember to remove the key from the
ignition switch.
Children or bystanders may be injured if they
move or attempt to operate the tractor while it is
unattended.
Always remove the ignition key and move the
motion control levers to the brake position when
leaving the machine unattended, even if just for a
few minutes.
Caution
Adjusting the Height of Cut
The height of cut is adjusted from 1-1/2 to 4-1/2 inch (38 to
114 mm) in 1/2 inch (13 mm) increments by moving the
height-of-cut lever in different locations.
1. Raise the height-of-cut lever to the transport position
(also the 4-1/2 inch (114 mm) cutting height position)
(Fig. 10).
2. To adjust, pull up on the height-of-cut lever and move it
to the desired position (Fig. 10).
m–6421
A
B
C
D
E
F
G
2 inch (51 mm)
2–1/2 inch (64 mm)
3 inch (76 mm)
3–1/2 inch (89 mm)
4 inch (102 mm)
4–1/2 inch (114 mm)
1–1/2 inch (38 mm)
Figure 10
1. Height-of-cut lever 2. Height-of-cut positions
Adjusting the Mower Wheels
The front mower wheels are to guide the mower over
uneven ground. The front wheel height can be changed to
closely match the selected height of cut for the mower.
1. To change the height of the mower front wheels,
remove the wheel mounting bolt and change the hole
into which the wheel is mounted (Fig. 11).
2. Use the top hole for the lowest cutting height and the
bottom hole for higher cutting heights (Fig. 11).
1505
1
2
3
4
Figure 11
1. Wheel
2. Wheel bracket
3. Locknut
4. Wheel bolt
17
Positioning the Seat
The seat can move forward and backward. Position the seat
where you have the best control of the machine and are
most comfortable.
1. Raise the seat and loosen the adjustment knobs
(Fig. 12).
2. Move the seat to the desired position and tighten the
knobs.
m–6433
1
Figure 12
1. Adjustment knobs
Adjusting the Motion Control
Levers
The motion control levers can be adjusted higher or lower
for maximum operator comfort.
1. Remove the 2 bolts holding the control lever to the
control arm shaft (Fig. 13).
2. Move the control lever to the next set of holes. Secure
the lever with the 2 bolts (Fig. 13).
3. Repeat the adjustment for the opposite control lever.
1
2
3
m–6417
Figure 13
1. Control lever
2. Bolt
3. Control arm shaft
Pushing the Machine by Hand
Important Always push the machine by hand. Never
tow the machine because damage may occur.
To Push the Machine
1. Park the machine on a level surface and disengage the
blade control (PTO).
2. Move the motion control levers to the brake position,
stop the engine, remove the key, and wait for all moving
parts to stop before leaving the operating position.
3. Push each bypass lever forward and then push them out
(Fig. 14).
4. Move the motion control levers to the center, unlocked
position to disengage the brake (Fig. 9).
5. Push the machine.
18
3
2
m–6418
1
1
Figure 14
1. By–pass valve
2. Position for operating the
machine
3. Position for pushing the
machine
To Operate the Machine
Push the two bypass levers towards the inside and then pull
them rearward (Fig. 14).
Note: The machine will not drive unless the bypass levers
are pushed in and then to the outside.
Adjusting the Footrest
The footrest can be adjusted forward or backward for
maximum operator comfort.
1. Lift up the footrest and place the rods in the same hole
positions (Fig. 15).
m–6423
1
3
2
3
Figure 15
1. Footrest
2. Rod
3. Hole positions
Removing and Installing the
Engine Hood
1. To remove the hood, loosen the knobs and then pull the
hood back and up (Fig. 16).
2
1
m–6480
Figure 16
1. Engine hood 2. Knob
2. To install the hood, put the hooks into the slots and slide
forward (Fig. 17).
3. Tighten the knobs (Fig. 16).
19
1
2
m–6479
Figure 17
1. Engine hood 2. Hook
Side Discharge or Mulch Grass
This mower is able to mulch or side discharge grass.
Coming from the factory, the mower is in mulching mode.
Danger
Without the grass deflector, discharge cover, or
complete grass catcher assembly mounted in place,
you and others are exposed to blade contact and
thrown debris. Contact with rotating mower
blade(s) and thrown debris will cause injury or
death.
Never remove the grass deflector from the
mower because the grass deflector routes
material down toward the turf. If the grass
deflector is ever damaged, replace it
immediately.
Never put your hands or feet under the mower.
Never try to clear discharge area or mower
blades unless you move the power take off
(PTO) to disengage and turn the ignition key to
off. Also remove the key and pull the wire off
the spark plug(s).
The mower has a hinged grass deflector that disperses
clippings to the side and down toward the turf, while in side
discharge mode.
To mulch grass clippings the discharge cover (optional on
some models) must be installed into the opening in the side
of the mower; refer to Installing the Discharge Cover,
page 19.
Installing and Removing the
Discharge Cover (For Both
Models)
Installing the Discharge Cover
1. Stop the engine and remove the ignition key.
2. Lift the grass deflector and slide the tabs on top of the
discharge cover under the grass deflector retaining rod.
Rotate the discharge cover down over the opening, and
onto the lower lip of the mower (Fig. 18).
3. Secure the discharge cover to the lower lip of the
mower with bolts and nuts (Fig. 18).
Note: Do not over-tighten the nuts, which could distort the
cover and cause blade contact.
1
6
5
4
3
6
5
2
m–6469
Figure 18
1. Grass deflector
2. Tabs under retaining rod
3. Discharge cover
4. Lower lip
5. Bolt
6. Nut
Removing the Discharge Cover
To convert to side discharge mode do the following
procedure.
1. Stop the engine and remove the ignition key.
2. Remove the nuts and bolts that secure the discharge
cover to the mower (Fig. 18).
3. Remove the discharge cover and lower the grass
deflector over the discharge opening.
20
Removing and Installing the
Mulching Baffles (For Model
74402 Only)
Removing the Mulching Baffles
Complete the following procedure to convert your
mulching mower into a side discharge mower.
1. Raise the mower to the G position (4–1/2 inch)
(Fig. 10).
2. Remove the bolts and locknut from the front baffle and
remove the baffle (Fig. 19). Save these bolts and
locknut.
5
m–6468
1
3
4
2
1
2
3
6
Figure 19
1. Front baffle
2. Bolt
3. Locknut
4. Middle baffle
5. Slot in discharge cover
6. Mower wheel bracket
3. Remove the nuts and bolts from the middle baffle.
(Fig. 19).
4. Install bolts and locknuts into the mower wheel bracket
and mower (Fig. 19).
Open holes in the mower expose you and others to
thrown debris which can cause severe injury.
Never operate the mower without hardware
mounted in all holes in the mower housing.
Install the hardware in the mounting holes when
you remove the recycling baffle.
Warning
Installing the Mulching Baffles
Complete the following procedure to convert back to a
mulching mower.
1. Thoroughly clean the mower.
2. Remove the locknuts and bolts from the front baffle
mounting holes (Fig. 19).
3. Install the middle baffle to the mower with 2 bolts and
locknuts removed in step 2 (Fig. 19).
4. Install the front baffle into the slot in the discharge
cover (Fig. 19).
5. Install the front baffle to the mower with three bolts and
one locknut (Fig. 19).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Toro 14-38Z TimeCutter Z Riding Mower User manual

Category
Lawnmowers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI