Hallman HGR24CMBGLP User manual

Brand: Hallman

Model: HGR24CMBGLP

Category: Ovens

Type: User manual

This manual is also suitable for

HGR24CMSS

07/2016

cod. I/301/89/HA

User Instructions, Installation, maintenance for

•COOKERS•

Majestic • Professional • Quadra

Cookers characteristics

These warnings refer to different models of cookers.

Be sure that you have correctly identifiedthe model that you possess (see the data plate).

MODEL DIMENSIONS

UP60 23 5/8” (W) x 23 5/8” (D) x [33 15/32”- 35 53/64“] (H)

UP76 29 7/8” (W) x 23 5/8” (D) x [33 15/32” - 35 53/64”] (H)

UM76 29 7/8” (W) x 27 9/16” (D) x [34 1/4”- 36 20/32”] (H)

UP90, UPD90 35 7/16” (W) x 23 5/8” (D) x [33 15/32”- 35 53/64”] (H)

UM90 35 7/8” (W) x 27 9/16” (D) x [34 1/4”- 36 20/32”] (H)

UPD100 39 3/8” (W) x 23 5/8” (D) x [33 15/32”- 35 53/64”] (H)

UQM100 39 3/8” (W) x 25 19/32” (D) x [34 1/4”- 36 20/32”] (H)

UMD100 39 3/8” (W) x 27 9/16” (D) x [34 1/4”- 36 20/32”] (H)

UP120,UPD120 47 1/4” (W) x 23 5/8” (D) x [33 15/32”- 35 53/64”] (H

UM120 47 7/8” (W) x 27 9/16” (D) x [34 1/4”- 36 20/32”] (H)

UP150 59 1/16” (W) x 23 5/8” (D) x [33 15/32”- 35 53/64”] (H)

UM150 59 1/2” (W) x 27 9/16” (D) x [34 1/4”- 36 20/32”] (H)

• Installation must conform with local codes or in absence of codes, the National Fuel Gas Code ANSIZ223.1-latest

edition. Electrical installation must be in accordance with the National Electrical Code, ANIS/NFPA70 – latest

edition and/or local codes. IN CANADA: Installation must be in accordance with the current CAN/CGA-B149.1

National Gas

• Installation Code or CAN/CGA-B 149.2, Propane. Installation Code and/or local codes. Electrical installation must

be in accordance with the current CSA C22.1 Canadian Electrical Codes Part 1 and/or local codes.

• Installation of any gas –ﬁ red equipment should be made by a licensed plumber. A manual gas shut-oﬀ valve must

be installed in the gas supply line ahead of the oven in the gas stream for safety and ease of service.

• In Massachusetts: All gas products must be installed by a “Massachusetts” licensed plumber or gasﬁ tter. A “T”

handle type manual gas valve must be installed in the gas supply line to this appliance.

• The manufacturer will not be responsible for any damage to property or to persons caused by incorrect installation

or improper use of the appliance.

• The manufactured reserves the right to make changes to its products when considered necessary and useful,

without aﬀ ecting the essential safety and operating characteristics.

• This appliance has been designed for non-professional, domestic use only.

• This appliance must be used only for the purposes for which it was intended. Any other use is incorrect and

therefore dangerous.

• Possible hazards may result from using this appliance for storage space.

IMPORTANT - PLEASE READ AND FOLLOW

• Before beginning, please read these instructions

completely and carefully.

• Do not remove permanently afﬁ xed labels, warnings, or

plates from the product. This may void the warranty.

• Please observe all local and national codes and

ordinances.

• Please ensure that this product is properly grounded.

• The installer should leave these instructions with the

consumer who should retain for local inspector’s use and

for future reference.

NEVER use this appliance as a space heater to heat or warm

the room. Doing so may result in carbon monoxide poisoning.

WARNING

Keeping appliance area clear and free from combustible materials, gasoline and other ﬂ ammable vapors

and liquids.

IMPORTANT INSTRUCTION

All Appliances:

Do Not Leave Children Alone - Children should not be left alone or unattended in area where appliance is in use.

They should never be allowed to sit or stand on any part of the appliance. Do not store items of interest to children

above or at the back of this appliance, as they could climb on the appliance to reach items and be injured.

Wear Proper Apparel - Loose-ﬁ tting or hanging garmets should never be worn while using the appliance.

User Servicing - Do not repair or replace any part of the appliance unless speciﬁ cally recommended in the manual.

All other servicing should be referred to a qualiﬁ ed technician.

Storage in or on Appliance - Flammable materials should not be stored near surface units.

Do Not Use Water on Grease Fires - Smother ﬁ re or ﬂ ame or use dry chemical or foam type extinguisher.

Use Only Dry Potholders - Moist or damp potholders on hot surfaces may resultin burns from steam. Do not let

potholder touch hot heating elements. Do not use a towel or other bulky cloth.

When using this appliance, do not touch grates, burner caps, burner bases or any other parts in proximity to the

ﬂ ame. These components may be hot enough to cause burns.

Never leave this appliance unattended when in use. Boilovers and greasy spills may smoke or ignite

Do not heat unopened food containers, such as baby food jars and cans. Pressure build-up may cause the container

to burst and cause injury.

Before performing service, shut oﬀ gas supply by closing the gas shut-oﬀ valve and shut oﬀ elec-tricity to this

appliance

For safety when cooking, set burner controls so ﬂ ame does not extend beyond the bottom of pan.

• Wear proper apparel. Loose-ﬁ tting or hanging garments should never be worn while using this appliance.

• Use extreme caution when moving a grease kettle or disposing of hot grease.

• Clean only those parts listed in this guide.

• Do not repair or replace any part of this appli-ance unless speciﬁ cally recommended in literature accompanying

this appliance.

• Do not obstruct the ﬂ ow of air to ensure proper combustion and ventilation.

• IMPORTANT: Do not install a ventilation system that blows air downward toward this gas cooking appliance. This

type of ventilation system may cause ignition and combustion problems with this gas cooking appliance resulting in

personal injury or unintended operation.

Ovens:

Use Care When Opening Door - Let hot air or steam escape before removing or replacing food.

INSTALLATION INSTRUCTIONS

This appliance shall only be installed by an authorized person. This appliance shall be installed in

accordance with the manufactures installation instructions, IMPORTANT: this appliance must be installed in

accordance with the norms in force of the country concerned.

The installation of this appliance must conform to local codes and ordinances. In the absence of local codes.

Installations must conforms to American National Standards, National Fuel Gas Code ANSI Z223.1-54

If local codes permit, a ﬂ exible metal appliance connection with the new AGA or CGA certiﬁ ed design,

max. 5 feet (1,5m) long, ½” I.D. recommended for connecting this cooktop to the gas supply line. Do not

bend or damage the ﬂ exible connector when moving the cooktop. The pressure regulator has ½” female

pipe thread. You will need to determine the ﬁ tting required, depending on the size of your gas supply line,

the ﬂ exible metal connector and the shutoﬀ valve.

The appliance , when installed, must be electrically grounded in accordance with local codes or, in absence

of local codes, with the National Electrical Code, ANSI/NFPA 70.

The appliance and its individual shut oﬀ valve must be disconnected from the gas supply piping system

any pressure testing of that system at test pressure in excess of ½psi (3,5kPa).

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoﬀ

valve during any pressure testing of the gas supply piping system at test pressure equal to or less than

½psi (3,5kPa).

For use with a pressure regulator. The regulator supplied must be used with this appliance; it shall be

properly installed in order to be accessible when appliance is installed in deﬁ nitive position.

The gas appliance pressure regulator must be set for the gas with which the appliance is used.

This appliance can be used with Natural gas and LP Gas. It is shipped from the factory adjusted for use

with Natural gas: CONVERSION FIXED ORIFICES ARE LOCATED IN THE LITERATURE PACK SUPPLIED

WITH THE UNIT.

Injectors kit for the change of type of gas are contained inside the package jointly with the hob installation

kit and Instruction booklet. The maximum inlet gas supply pressure incoming to the gas appliance pressure

regulator is 20” water column (5kPa). The minimum gas supply pressure for checking the regulator setting

shall be at least 1”w.c.(249Pa) above the inlet speciﬁ ed manifold pressure to the appliance (this operating

pressure is 5”w.c. for Natural Gas and 10”w.c. for LP Gas.All opening and holes in the wall and ﬂ oor, back

and under the appliance shall be sealed before installation of the appliance.

ATTENTION: A manual valve shall be installed in an accessible location in the gas line external to the appliance for the

purpose of turning on or shutting off gas to the appliance.

WARNING: Do not use aerosol sprays in the vicinity of this appliance while it is in operation.

The appliances should not be installed with a ventilation system that blows air downward toward the range.

BC B B

Fig.2a Fig.2b

ABCCAB

BASE FEET

Legs are packed in carton box. Legs should be installed near to where the appliance is to be used, as they are not

secure for long transit. After unpacking the range, raise it about a foot to remove the bottom shipping skid. Keep the

unit raised to permit legs to be screwed into our couplings and lower it gently to keep any undue strain from the legs

and internal mounting hardware. It is strongly recommended that a pallet or lift jack be used rather than tilting.

Fig.1a

1) Remove the foot (A) from the cooker and

ﬁ x in the foot cover (D)

2) Secure the foot cover (D) with three bolts,

the three whashers and the three nuts (B)

into the bracket (C) which is positioned at

the rear of the kitchen

Fig.1c

1) Screw partially bolt (F)

into the base feet (G).

2) Insert base feet (G) into

the hole (Ha), move to the

hole (Hb) and screw com-

pletely bolt (F).

Fig.1b

1) Insert the bolt (A) into the bra-

cket hole and tighten the nut (B).

2) Insert the pin between the bra-

cket and the ﬁ xing support (D)

and tighten the nut (B).

PRESSURE GAS REGULATOR INSTALLATION INSTRUCTION

Pressure gas regulator is supplied with the appliance. It is stored in the oven.

As show in Figure 2a, unscrew B part from C part.

Screw B part into A part (Fig. 2a). Please use a proper gasket, for this connection.

As show in Figure 2b, screw A+B part into part C.

MAJESTIC PROFESSIONALMAJESTIC PAW LION FEET

ANTI-TIP STABILITY DEVICE INSTALLATION INSTRUCTIONS

1. The anti-tip bracket have to be attached to rear wall, as show in Fig.4, before backguard installation. The dimension

for the bracket location from the ﬂ oor have to be determined after range legs have been adjusted to the proper

installation height as show in the installation instructions and the range has been levelled.

2. Measure from the ﬂ oor to the bottom of the anti-tip location on the back of the range.

3. Locate the two anti-tip bracket holes (dimension of the holes 15/64”(6mm)) on the wall at the measured dimension

plus 5/32”(4mm). The two anti-tip have to be placed close to the side of the range location (recommended

dimension is 1”(25,4mm from the sides).

4. Fix the two bracket on the wall.

5. Install backguard, as shown at the next part (see Install backguard chapter).

6. Adjust range legs 5/16”(8mm) shorter than the proper installation height. Slide in then the range against the wall.

Adjust range legs to the proper installation height.

BACKGUARD INSTALLATION INSTRUCTION

Please follow the following installation instructions in sequence:

1. install base feet (see proper instruction Fig.3)

2. Place the backguard and fix it from bottom side with the two screw as shown in figure below.

Figure 3

Figure 4

PROXIMITY TO SIDE CABINET INSTALLATION

1. This range may be installed directly adjacent to existing [33 15/32” - 36 20/32”] high base cabinets. IMPORTANT:

The top border of the worktop should be at the same level of the adjacent cabinets counter top. This may be

accomplished by raising using the adjustment spindles on the legs.

2. The range CANNOT be installed directly adjacent to sidewall, as cabinets, appliances, or other side vertical surface

above 36 20/32” high. There must be a minimum of 5” side clearance.

3. Within the side clearance to combustible vertical surfaces above 36 20/32”, the maximum wall cabinet depth

must be 13” and wall cabinets within this side clearance within this side clearance must be 18” above the 36” high

countertop.

4. Distance A cannot be less than width of the appliance.

Figure 5

TABLE 1

A ≥ [23 15/32” – 59 1/2”] [60cm – 151cm]

B 36” (91,5cm)

C 13” (33cm)

D 18” (45,7cm)

E 36” (91,5cm)

F 5” (12,7cm)

ELECTRICAL CONNECTION

The appliance shall be connected to a single phase electric line rated at 120/208Vac or

120/240Vac and 60Hz frequency.

The appliance is equipped at the factory with a flexible hose . Inside the flexible hose you have

4 cables: grenn cable must be connected to the ground, white cable (NEUTRAL), red en black

cables: supply wire (L1 – L2). Check the electrical schetch available at the bottom in our in-

structions booklet

Electric power absorption of each model are shown in the Electrical and Gas Power Table en-

closed.

Before connecting the appliance to the electric network, follow the instructions below:

1. fuse and electric feeding installation of your home must support the load of the appliance (see registration label).

2. Power supply system must have an eﬃ cient earth plate.

3. The outlet or multiple-switch, with a minimum1/8” (3mm) contact opening, has to be easily reached once the

appliance has been installed.

The appliance is supplied without outlet: you need a normal one proper for the electric load.

The power supply cable should not reach a 120°F temperature above the one surrounding.

GAS CONNECTION

All gas connections must be made according to national and local codes. This gas supply (ser-

vice) line must be the same size or grater than the inlet line of the appliance. This range uses a

½”NPT inlet. Sealant on all pipe joints must be resistive to LP gas.

1. Manual Shut-oﬀ Valve: This installer-supplied valve must be installed in the gas service line ahead of the appliance

in the gas stream and in a position where it can be reached quickly in the event of an emergency. The manual

shut-oﬀ valve shall be installed properly in order to be accessible when appliance is installed in deﬁ nitive position.

In Massachusetts: A ‘T’ handle type manual gas valve must be installed in the gas supply line to this appliance.

2. Pressure Regulator

1. All heavy duty, commercial type cooking equipment must have a pressure regulator on the incoming service line

for safe and eﬃ cient operation, since service pressure may ﬂ uctuate with local demand. The pressure regulator is

supplied separately with the appliance; regulator has two female threads ½” NPT; it shall be installed properly in

order to be accessible when appliance is installed in deﬁ nitive position.

2. This range can be used with Natural or LP/Propane gas. It is shipped from the factory adjusted for use with natural

gas. The oriﬁ ce hoods must be screwed snug when LP/Propane gas is used(see LP/Propane conversion).

3. The appliance, its individual shut-oﬀ valve, and pressure regulator must be disconnected from the gas supply

piping system during any pressure testing of that system at pressure is in excess of 1/2psig(3.45kPa).

4. The appliance must be isolated from the gas supply piping system by closing its individual manual shut-oﬀ valve

during any pressure testing of gas supply piping system at test pressures equal to or less than 1/2psig(3.45kPa).

3. Flexible Connections:

1. If the unit is to be installed with ﬂ exible couplings and/or quick disconnect ﬁ ttings, the installer must use an heavy

duty, AGA design-certiﬁ ed commercial ﬂ exible connector of at least ½”(1.3cm)ID NPT(with suitable strain relieves)

in compliance with ANSI Z21.41 and Z21.69 standards.

2. In Massachusetts: The unit must be installed with a 36” (3-foot) long ﬂ exible gas connector.

3. In Canada: CAN 1-6.10-88 metal connectors for gas appliances and CAN 1-6.9M79 quick disconnect device for

use with gas fuel.

CAUTION: Leak testing of the appliance shall be conducted according to the manufacturer’s instructions. Before placing the

oven into operation, always check for leaks with a soapy water solution of other acceptable method. DO NOT USE AN OPEN

FLAME TO CHECK FOR LEAKS!

PERFORMANCE CHECKLIST

All burners are tested before leaving the factory. There are no adjustments for the burners

if connected according to the information on the rating plate. Check each burner for proper

operations. Flames should be blue in all settings. If service is required, contact your dealer for

the name of their authorized service agency. Gas conversions and initial installation are not

responsibility of the manufacturer.

The installer should carry out the following performance checks. Refer to instructions below.

1. Check surface burner ignition.

2. Check air shutter adjustment (only for oven and broiler burner) sharp blue ﬂ ame, no yellow tipping, shooting or

ﬂ ame lifting.

3. Check low ﬂ ame adjustment

4. Check broiler and oven ignition - all burners ports.

5. Check for gas leaks (odors) at all gas connections.

6. Check oven bake and convection bake function.

REQUIREMENTS

Room ventilation – Location and venting.

ATTENTION: A exhaust fan may be used with the appliance; in each case it shall be installed in conformity with the

national standards in force.

ATTENTION: Exhaust hood operation may affect other vented appliances; in each case it shall be installed in conformity

with the national standards in force.

CONVERSION TO DIFFERENT TYPES OF GAS

Any conversion required must be performed by your dealer or a qualified licensed plumber or gas service company.

Please provide the service person with this manual before work is started on the range.(Gas conversions are the

responsibility of the dealer or end user.)

WARNING

This conversion kit shall be installed by a qualified service agency in accordance with the

manufacturer’s instructions and all applicable codes and requirements of the authorityhaving

jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or

production of carbon monoxide may result causing property damage, personal injury or loss of life.

The qualified service agency is responsible for the proper installation of this kit. The installation

is not proper and complete until the operation of the converted appliance is checked as specified

in the manufacturer’s instructions supplied with the kit.

CAUTION

Before proceeding with the conversion, shut off the gas supply to the appliance prior to disconnecting

the electrical power.

The appliance is supplied for use with a certain type of gas; if this has to be varied, you must change the burner

injectors, adjust the air flow rate and the minimum gas flow.

Before carrying out these operations you must disconnect the electric power supply of the cooker to avoid accidental

contacts.

Before carrying out any maintenance work, disconnect the appliance from the gas and electric supply.

ADAPTATION OF THE PRESSURE REGULATOR FOR

USE WITH DIFFERENT TYPE OF GAS

The pressure regulator supplied with the appliance is a convertible type pressure regulator for

use with Natural Gas at a nominal outlet pressure of 5”w.c. or LP gas at a nominal outlet pressure

of 10”w.c. and it is pre-arranged from the factory to operate with one of these gas/pressure as

indicated in the pre-arranging labels affixed on the appliance, package and Instruction booklet.

If Natural gas is converted to LP gas, also by-pass orifice has to be change.

The regulating crew of by-pass orifice must be fully screwed in.

To convert the regulator (Fig.6 and Fig.7) for use with the other gas different from which one it is

pre-arranged it is enough perform the following operations:

1. Unscrew by hand the upper metal stopper of the regulator.

2. Unscrew by hand the white plastic piece screwed under the above mentioned metal stopper, afterward screw

it again in opposite way under the metal stopper(for gas reference see the written “LP” and “NAT” with relative

indicating arrows on the white piece).

3. Screw again by hand the metal stopper in the original position on the regulator.

Operating in this way the gas regulator is converted for use with the other gas/pressure

Figure 6 Figure 7

Pressure regulator Pressure regulator; pressure

test-point stopper is pointed out

CHANGING THE INJECTORS AND ADJUSTING THE AIR

TABLE 2

Burner Gas INPUT

RATE

[Btu/h]

ORIFICE

SIZE

(1/100) mm

SIMMER

RATE

[Btu/h]

PRIMARY

AIR

OPENING

BY-PASS

ORIFICE

SIZE

(1/100)mm

SR NATURAL (A) 7000 120 2100 Open Adj.*

R NATURAL (A) 10500 145 3200 Open Adj.*

Fish Kettle NATURAL (A) 10500 145 3600 Open Adj.*

TC NATURAL (A) 15500 180 5600 Open Adj.*

Dual NATURAL (A) 15500 165+68 8000

15 (external)

/ Open (inner

ring)

Adj.*

Dual (aux only) NATURAL (A) 2300 68 1100 Open Adj.*

Griddle NATURAL (A) 10500 145 3600 Adj.*

Big Solid Top Bur-

ner

NATURAL (A) 8500 130 2100 5 Adj.*

Small Solid Top Bur-

ner

NATURAL (A) 8500 130 2100 5 Adj.*

OVEN (60) NATURAL (A) 11500 155 4

GRILL (60) NATURAL (A) 9000 140 /

OVEN (70) NATURAL (A) 15000 180 4

GRILL (70) NATURAL (A) 13500 165 /

OVEN (90) 1 burner NATURAL (A) 15000 180 /

GRILL (90) NATURAL (A) 13500 165 /

SR LP (E) 7000 78 2100 Open 45

R LP (E) 10500 95 3200 Open 55

Fish Kettle LP (E) 10500 95 3600 Open 60

TC LP (E) 15500 117 5600 Open 75

Griddle LP (E) 10500 95 3600 60

Dual LP (E) 15500 110+43 8000 Open 75

Dual (aux only) LP (E) 2300 43 1100 Open 35

Big Solid Top Bur-

ner

LP (E) 8500 85 2100 5 45

Small Solid Top Burner

LP (E) 8500 85 2100 5 45

OVEN (60) LP (E) 11500 95 2800 20 55

GRILL (60) LP (E) 9000 88 /

OVEN (70) LP (E) 15000 115 20

GRILL (70) LP (E) 13500 105 /

OVEN (90) 1 burner LP (E) 15000 115

GRILL (90) LP (E) 13500 105 /

A1) Burners of the hob

1. Remove the grill, the caps and the burners from the worktop.

2. Lift the worktop.

3. Unscrew the screw “F” and remove the pipe “R”.

4. Unscrew the injectors (U) and replace them with those suitable for the gas used, supplied with the cooker. See TABLE 2.

5. The air is adjusted by means of the pipe “R” according to the value “X” given in TABLE 2 for the primary air opening.

Once regulation has been completed, secure the pipe ”R” with the screw “F”.

A2) Air adjustment

The air adjustment must be carried out with the burner ignited and the flame to the maximum.

Examples (Fig.10):

A) Flame with excess of air; it is small and thin. Move sleeve R forward.

B) Flame with lack of air; it is irregular with yellow streaks. Move sleeve R backward.

C) Normal ﬂ ame: its colour is light blue.

Figure 8 Figure 9 Figure 10

B1) Burner in the oven

1. Remove the bottom shelf of the oven

2. Remove the ﬁ xing screws to move the burner

3. Unscrew the injectors and replace it with one suitable for the gas used. See table 2.

4. Unscrew the screw “f”.

5. The burner air must be adjusted by means of the pipe “r” according to the value ”x” given in table 2 for the

“primary air opening”.

6. Once regulation has been completed, secure the pipe “r” with the screw “f”.

B2) Air adjustment

The air adjustment must be carried out with the burner ignited and the flame to the maximum.

Examples (Fig.12):

D) Flame with excess of air; it is small and thin. Move sleeve R forward.

E) Flame with lack of air; it is irregular with yellow streaks. Move sleeve R backward.

F) Normal ﬂ ame: its colour is light blue.

Figure 11 Figure 12

By-pass

regulating

screw

Figure 14b (DUAL)

AUX AUX

Figure 13 Figure 14a

ADJUSTING THE MINIMUM GAS FLOW

When installing the cooker you must check that the minimum gas ﬂ ow of the burners on the hob and in the oven is

correctly regulated. If the type of gas is changed it is indispensable to adjust the minimum ﬂ ow. The regulating procedure

is as follows.

A) Burners on the hob (fig. 13)

1. Light one burner at a time and turn the flame up to maximum.

2. Remove the knob of the corresponding gas tap and insert screwdriver in the screw as showed in figure

14a or 14b (DUAL).

3. Turn the tap to minimum position.

4. Unscrew, turning to the left, to increase the flame, or screw to the right to decrease it.

5. If a liquid gas is used (Butane - Propane), the regulating screw must be fully screwed in.

SERVICE & MAINTENANCE INSTRUCTIONS

Replacement Parts.

Authorized replacement parts may be used in performing service on the appliance. Replacement parts are available

from factory authorized part distributors.

Service and maintenance only to be carried out by an authorised person.

To replace parts such burners, valves and electric components, the hotplate must be removed from the bench

top by releasing the attachment hooks, loosening the attachment screws of each burner, unscrewing the hotplate

attachments nuts which are visible at the bottom of the surface, removing the hotplate top and ﬁ nally replacing the

defective parts.

Note: if the valves must be replaced, ﬁ rst disassemble the ignitions switches wires.

It is recommended to replace the valve gaskets each time the valve is replaced.

WARNING: After first installation of the appliance or after any service intervention concerning main gas parts of the

appliance, make the leak test using water with soap an the gas connections in order to verify the correct installation.

Do not use fire for gas leak testing.

NON WORKING APPLIANCES

Before calling the After Sales Service, check that the appliance is connected or that the main switch is activated.

After, call the After Sales Service. The faults must be checked by a skillfull technician.

Remark: the appliance is equipped with a safety thermostat, adjusted at a certain temperature. In case it reaches a

higher temperature, the appliance switches oﬀ .

OVEN CLEANING AND CARE

It is advised to clean the oven after each use. The dirt comes oﬀ more easily, preventing it from being burnt repeatedly

at high temperatures. Wait until the chamber is lukewarm. Remove all the extractable parts and wash them separately

in hot water and non abrasive detergent. The cooking chamber can be cleaned with a soft cloth soaked in a solution

of lukewarm water and ammonia; then rinse and dry. Do not use abrasive or corrosive detergents as they may

damage the oven. Do not use steam appliances for cleaning, as there is a risk of short circuit.

DISMANTLING THE OVEN DOOR

For ease of intensive cleaning it is practical to dismantle the door following these instructions: insert the hook (C) (Fig.

16) in the hinge sector (D). Put the door in half-open position and, using both hands, pull the small door towards you

until it uncouples from the connection. To reassemble the door, proceed in inverse order, taking care to insert the two

guides (F) correctly.

OVEN DOOR

The oven door is composed of three sheets of plate glass (two in some models). The plate glass parts may be cleaned

using absorbent kitchen paper and an ordinary non abrasive detergent. The inside glass may be removed to facilitate

cleaning.

To do this it is necessary to dismantle the oven door (see paragraph “Dismantling the oven door”) or, alternatively, to

set it in the intermediate click position.

ATTENTION: DO NOT SLIDE OUT THE INSIDE GLASS WITH THE DOOR COMPLETELY OPEN THE DOOR COULD CLOSE SUDDENLY AND

HURT YOU.

Once the door has been dismantled, place it with the outside facing down on a ﬂ at soft surface to avoid scratching

it. If you do not want to dismantle the door, it is possible to slide out the glass by setting it in the intermediate click

position (see Fig. 17), but take care that the door does not close suddenly

Figure 16 Figure 17

Self-cleaning panels

If the oven is equipped with self-cleaning catalytic panels, at normal cooking temperatures (430°F) the catalytic

enamel favours the transformation of splashes of fat into a light powder residue. This powder may be removed with

a damp cloth once the oven has cooled. In this way the enamel surface remains porous and ensures maximum yield

of the panels.

Fat-filter

(in selected models only)It is recommended that the fat ﬁ lter is cleaned regularly as a build up of grease could

damage the thermostat and the fan motor.

Fig. 18: Removal of oven shelf support

Fig. 19: Removal of fat-ﬁ lter (F)

Fig. 20: Removal of oven lamp

When the oven is out of order

In case your appliance is not working correctly, disconnect it from the mains and call the After Sales Service.

In case oven light is not working properly, disconnect the appliance from the mains, remove the protection glass of

the lamp and replace it (Fig. 20).

Take care that lamp must be suitable for working at high temperatures and has the proper technical features.

Cleaning the grills

We advise always cleaning the pan support grills after cooking. Wait until they have cooled down and then clean them

with a NON ACID detergent. Acid substances such as lemon juice or other acid detergents may cause irremediable

damage to the enamel on the grills. Dry the grills carefully with a cloth immediately after washing them. Washing in

the dishwasher not recommended.

IMPORTANT

Insert foods when the oven is hot.«Grill» baking.

When appliances are equipped with grill, baking can be achieved keeping the door closed. By using the grill you can

cook meat, fish and even vegetables. At first, we suggest using the upper runner (4). Position the selector on grill

and fix the temperature of 360˚F.

Figure 18 Figure 19 Figure 20

USER MANUAL

IMPORTANT: keep children away from the appliance when it operates. The oven door becomes very hot. Safety rules

do not always cover any type of accident. The appliance must not be used for heating purposes. If other electric

appliances are connected to outlets placed near the appliance, make sure that the connection cables will not be

trapped in the oven door while operating.

GENERAL NOTES: for safety reasons and to ensure proper functioning of the appliance, any required maintenance

must be undertaken by skilled technicians or after sales service in warranty period. Clean the oven regularly after

the use. The dirt can be easily removed, in this way it will not burn at high temperatures. Choose heat-resisting pans

according to the quantity of food you want to cook. Stainless steel containers are not recommended as they reﬂ ect

heat. Shelf height should be adjusted as necessary according to the food to be cooked and the recipe.

FIRST SYSTEM STARTUP: all removable parts of the oven, should be washed with detergent and then reassembled.

Start the oven for about 60 minutes and set the thermostat to 440°F. During this initial heating period some unpleasant

smell will be experienced, which is unavoidable and quite normal. When the oven has completely cooled down, clean

it referring to the paragraph «Cleaning and care».

IMPORTANT: correct positioning of the brass ﬂ ame distributor (d, Fig. 21) is very important. For this purpose, ensure

that the ﬂ ame distributor tooth (e, Fig. 21) coincides with the notch (b, Fig. 21) on the aluminium base (a, Fig. 21). To

keep the ﬂ ame distributor covers (c) new, you are advised to remove them before lighting the ﬂ ame.

IMPORTANT: be sure that you have correctly identiﬁ ed the model that you possess (see the data plate).The various

operations are described below, one after the other. Not all concern the cooker you have bought, select the ones that

do.

IMPORTANT: when you are using the oven for the ﬁ rst time,

let it work empty for one hour, leaving possibly the windows

of the kitchen open. The oven will emanate bad smells due

to production residuals such as greases, oils or resins. After

that the oven is ready for the ﬁ rst cooking.

USE OF THE ELECTRIC THERMOSTAT (Fig. 25)

The thermostat (Fig. 25) allows to choose the temperature

of the oven from 100°F to 500°F, turning the knob clockwise.

The pilot lamp will turn oﬀ when the selected temperature

has been reached. It will turn on again when the internal

temperature of the oven is decreased more than 10°F.

USE OF THE TURNSPIT (Fig. 23, 24)

Spit the meats to be cooked. Put the spit on the proper base

and insert it on the spit motor. Place the collector plate on

the lower shelf, ignite the grill, turn on the spit motor.

Figure 21

Figure 24

Figure 25

Figure 23

1. FUNCTIONS: cooking time - end of cooking - clock - timer - manual operation

2. DISPLAY - symbols indicating functions in progress:

duration and manual functions = pot symbol

automatic programme = “A”

minute minder = bell symbol

3. SETTING A FUNCTION

Select the function required by pressing the corresponding button and set the time with the +/- buttons.

4. KEYS FOR BUTTONS

Bell button

Cooking time button

End of cooking button

- + button = timer setting

Time is increased with the “+” button and decreased with the “-“ button at a speed directly proportional to the

length of the time for which the button is pressed.

5. CLOCK FUNCTION

The clock function is activated by pressing the cooking time and end of cooking buttons simultaneously.

The time is set by pressing the +/- buttons. Any previously set programmes will be automatically cancelled.

6. MANUAL FUNCTION

This function is set by pressing the cooking time and end of cooking buttons simultaneously.

The symbol “A” disappears and the pot symbol appears . Previously set programmes are cancelled.

7. SEMI-AUTOMATIC FUNCTION WITH COOKING TIME

Select the cooking time function (

button) and set the time with the +/- buttons. The symbols “A” and the

pot symbol appear. The oven is switched on. When the time coincides with the set time, shown on the end

of cooking button

,the oven is switched oﬀ and the pot symbol disappears. The buzzer then sounds. The

symbol “A” starts to ﬂ ash.

USE OF THE ELECTRONIC PROGRAMMER

REMARK: To know what the electronic programmer drive see ELECTRONIC PROGRAMMER TABLE (at the end of the booklet).

ATTENTION: DO NOT USE ELECTRONIC PROGRAMMER WHEN VENTILATED GAS FUNCTION IS SELECT.

8. SEMI-AUTOMATIC FUNCTION WITH END OF COOKING TIME

Choose the function end of cooking (

button) and set the ﬁ nal time with the +/- buttons. The symbols “A”

and the pot symbol appear. The oven is switched on. When the time coincides with the set time the oven is

switched oﬀ and the pot symbol disappears. The buzzer then sounds. The symbol “A” starts to ﬂ ash.

9. AUTOMATIC FUNCTION WITH COOKING TIME AND END OF COOKING

Choose the function cooking time and set the required time with the +/- buttons. The symbol “A” appears.

The oven is switched on and the pot symbol appear. Wait a few seconds until the current time appears.

Set the end time using the end of cooking button , the approximate ﬁ nal time appears on the display.

Use the +/- buttons to set the ﬁ nal time actually required. The oven is switched oﬀ and the pot symbol

disappear. The pot symbol will appear again when the time coincides with the ﬁ nal time minus the cooking time.

At the end of the automatic programme the symbol “A” starts to ﬂ ash. The buzzer sounds and the oven and pot

symbol disappear.

10. MINUTE MINDER

Choose the timer function ( button) and set the required time with the +/- buttons. The bell symbol will

remain on for the duration of time set. At the end of this time the buzzer sounds.

11. BUZZER

The buzzer sounds at the end of the cooking time function and continues to buzz for 7 minutes. The buzzer is

silenced by pressing any of the buttons or .

The volume of the buzzer can be adjusted using the “-“ button without having ﬁ rst selected any function.

There are three diﬀ erent buzz volumes to choose from and their duration depends upon the length of time for

which the “-“ button is held pressed.

12. START OF A PROGRAMME AND CHECKING

Once a programme has been selected it starts after setting the time. The time remaining can be viewed at any

time by selecting the corresponding function again.

13. IDENTIFYING A PROGRAMMING ERROR

There is a programming error if the time indicated on the clock is between the cooking and end of cooking times.

The error is indicated by the buzzer sounding and the symbol “A” ﬂ ashing.

14. CANCELLING A PROGRAMME

To cancel a programme select the manual function. At the end of the set programme this is automatically cancelled.

15. IMMEDIATE USE

A) If the display ﬂ ashes read point B, otherwise go to point C.

B) If the display ﬂ ashes the correct time has not been set or there has been a power failure. In this case, set the

correct time (see paragraph 5) and then go to point C.

C) Press the

and button simultaneously. Set the temperature (thermostat knob) and function (selector

knob) using the knobs on the appliance.

Figure 26

USE OF THE MULTIFUNCTION OVEN

Turn the selector knob (S) and choose the function. Select the desired temperature from 100˚F to 500˚F turning the

thermostat (T). If your oven is ﬁ tted with a programmer then you have to switch it on.

Oven light

To switch on the oven light, press the button (R) on the left part of the board.

1 Pizza cooking

Pizza function suitable when cooking pizza, bread and scones. Lower heating element works with the other heating

elements of the oven.

2 Upper & lower elements

This operates like a conventional electric oven and can be used accordingly.

3 Lower element

As the heat comes from the lower element, this setting is particularly suitable for pastry and cakes e.g. ﬂ ans, pizzas,

biscuits, fruit cakes etc.

4 Upper element

Especially suitable for browning and to add the ﬁ nishing touches of colour to diﬀ erent dishes. We suggest this setting

when cooking hamburgers, pork outlets, steaks etc.

5 Grill-baking

Suitable for roast meats in general e.g. ﬁ llet steak, grilled ﬁ sh and vegetables. And also for cooking «au gratin» e.g.

cauliﬂ ower cheese

Use of the turnspit (available only on certain models)

Insert the spit on its support and in the motor placed in the back of the oven.

6 Grill & fan

An energy saving method for deep cooking. Suitable for chops, sausages, kebabs etc. This setting is also used to

operate the turn-spit on 35 45/64” ovens.

7 Upper lower elements and fan

A fast intensive form of cooking, suitable for a variety of dishes. It replaces the turn-spit and can be used for baked

ﬁ sh, braised vegetables, kebabs, roast chicken, duck etc.

8 Fan oven

This provides a more even heat than a conventional oven and food is «sealed» very quickly. As there is no top or

bottom heat the whole area of the oven can be utilized. This setting is ideal for batch baking or cooking a complete

meal. Several diﬀ erent dishes can be cooked using various shelf positions. Cooking temperatures required are lower

than in a conventionally heated oven. This not only saves energy but reduces the amount of spitting when roasting

meat.

9 Defrost function and Quick Start

Defrosting of frozen food is accelerated by means of fan driven air circulation.

Quick Start is a fast pre-heating oven function. When setting a cooking temperature between 390-500°F, it is advisable

to use the Quick Start function. First turn the oven function selector knob (S) to position (9). Turn the oven temperature

knob (T) to the desired temperature (between 390-500°F). When the orange thermostat light goes oﬀ this indicates

the selected temperature has been reached. Food to be cooked can now be placed into the oven. Now turn the oven

function selector knob (S) to the desired cooking function.

Warning: please note the Quick Start function is not suitable as a cooking function. It is a quick pre-heat system. The

Quick Start function should not be operated for more than 20 minutes.

Switch (S) Thermostat (T)

Page is loading ...

Hallman HGR24CMBGLP User manual

Brand: Hallman

Model: HGR24CMBGLP

Category: Ovens

Type: User manual

This manual is also suitable for

HGR24CMSS

Download PDF

report

Hallman HGR24CMBGLP User manual

This manual is also suitable for

Hallman HGR24CMBGLP User manual

Related papers

Other documents