CAREFULLY READ AND FOLLOW ALL SAFETY WARNINGS AND INSTRUCTIONS IN THIS MANUAL
Assembly Instruction
BEFORE
• Failure to follow these instructions could result in serious bodily injury and/or property loss.
ASSEMBLING AND OPERATING THE FIRE PIT TO AVOID PERSONAL INJURY OR PROPERTY DAMAGE! KEEP
THIS MANUAL FOR FUTURE REFERENCE.
• FOR OUTDOOR USE ONLY. DO NOT use this fire pit indoors or in any enclosed areas.
• At all times, keep the fire pit in a well-ventilated area.
• The fire pit should NEVER be used in a fully or pa
rtially enclosed area such as a garage,
breezeway, porch, or under any area that could catch fire.
• Proper clearance of at least 10 feet between the fire pit and any combustible materials (bushes,
landscape materials, trees, wooden decks, fences, buildings, etc.) should be maintained at all
times when the fire pit is in use.
• DO NOT use in windy conditions.
• Always place the fire pit on a flat and l
evel surface. DO NOT place the fire pit on a wood deck
or other combustible deck.
• The fire pit should NEVER be left unattended while in use.
• Extreme caution and care is necessary when handling fire and operating the fire pit.
• NEVER use gasoline, kerosene, alcohol or any other highly flammable liquid for lighting and
never add these liquids while the fire pit is in use.
• NEVER use the fire pit unles
s the fire pit is completely assembled and all parts are securely
fastened and tightened.
• This fire pit is intended to burn wood logs only, not to exceed 12 inches in length and 2 inches
in diameter. DO NOT burn coal, leaves, or other combustible materials in the fire bowl.
• NEVER touch parts of the fire pit until it has completely cooled to avoid injuries.
• DO NOT move the fire pit when it is in use
or when it is hot.
• NEVER wear loose clothing around the fire pit when it is in operation or while hot.
• NEVER remove ashes while the fire pit is in use or while cooling.
• NEVER dismantle the fire pit while in use or hot.
• When the fire pit is in use, the handle on the mesh screen/cover [Part A/B] can reach extreme
temperatures that can cause serious injury to an unprotected hand. Use the poker [Par
t J] to
remove the mesh screen when in use and wear appropriate heat resistant gloves when
removing the mesh screen with the poker.
• When the mesh screen/cover [Part A/B] is removed, place it on a level and non-combustible
service at least 10 feet away from any other combustible materials.
• At all times, use appropriate heat resistant gloves when adding proper wood logs to the fire.
• DO NOT use the fire pit or any portion of it, including the grate [Part C] or the fire bowl [Part H]
as a cooking appliance. The fire pit is not designed for grilling food.
• When the fire pit is not in use, make sure that the fire and any coals are completely and
thoroughly extinguished.
• Check state and local fire regulations and municipal laws for safe use.
• It is recommended to keep a fire extinguisher within reach.
1/3
PARTS LIST:
Tools required: screwdriver (not included)
1
2
3
6
7
8
5
4
A
B
B
9
A
A
B
Part No.
Description Qty
1
2
3
4
5
6
7
8
9
A
B
Lift Handle
1PC
Screen
1PC
Decorative rail
4PCS
Upper connector
4PCS
Grate supporter
4PCS
Cooking grill
1PC
Fire bowl
1PC
Leg
1PC
Poker
1PC
C
M6*15MM Bolt
M6 Nut
M6*10MM Bolt
8PCS
9PCS
6PCS
1. Unpack parts and put aside on a flat, non-abrasive surface. Check the parts list to make sure that
you have all the parts for the fire pit.
ASSEMBLY INSTRUCTIONS:
2. Choose a level location for setup.
3. Turn the fire bowl upside down (7) and place it on the level gr ound, insert the square end of leg (8)
into the slot of 7, use M6X10 bolts (C) to secure it. Do the same for the other two legs. Fig. 1.
8
7
C
C
2/3
4. Turn around the fire pit to have it stand upright on its legs. Connect the grate supporter (5) and
upper connector (4) with M6X15 bolts (A) and M6 nuts (B). Then join the two d ecorative rails (3)
together and fit its joint into the arc slot of (4), and nip them with the decorative rails (3) . F inally,
secure them with M6X15 bolts (A) and M6 nuts (B); d o the same for the other three parts. Fig. 2.
5. Connect lift hand
le (1) with screen (2) and use M6 nuts (B ) to connect them. Fig. 3.
6. Place the grill (6) and screen (2) on top of the fire bowl (7). U se the poker (9) for removal of the
mesh screen when in use. Fig. 4.
NOW THE FIRE PIT IS READY FOR USE.
OPERATING AND CARE INSTRUCTIONS:
1. Use the poker tool (J) provided to lift the mesh cover when using this fire pit. Do not lift the mesh
cover by hand when the fire pit is in use.
2. DO NOT leave this fire pit in the rain when it is not being used.
3. After using the fire pit, make sure that the fire and any coals are completely and thoroughly
extinguished. Allow the fire pit to completely cool down after use. After it has completely coole
d,
use a dry cloth to clean up the fire bowl, and then cover it with a PVC cover.
1
2
6
7
4
3
8
5
B
A
A
B
A
A
A
B
B
4
5
1
2
B
9
3/3
/
