Highwood AD-CNW44-ACE Operating instructions

Type
Operating instructions

This manual is also suitable for

For information on Care and Cleaning or to register your
highwood product, please visit www.highwood-usa.com.
PAGE 1 OF 1
IMPORTANT!
DO NOT fully tighten the nuts until all
nuts are started. Once all nuts are started,
go back & tighten all the nuts.
Retain these instructions for future reference
HARDWARE
high
wood
NATURE'S CLOSEST RIVAL
INCLUDED TOOLS
5/32" HEX KEY
Lehigh, Weatherly, or Adirondack Collection
Rectangular, Square, or Sideboard Tables
Assembly Guide
All AD-DTB/AD-CTB
08.07.2017
A
x8
1/4"-20 x 3" Bolt
This assembly guide applies to all tables displayed above!
- AD-DTB37/AD-CTB37 - Rectangular 36x72 Dining or Counter Height Dining Table
- AD-DTB47/AD-CTB47 - Rectangular 42x72 Dining or Counter Height Dining Table
- AD-DTB48/AD-CTB48 - Rectangular 42x84 Dining or Counter Height Dining Table
- AD-DTB25/AD-CTB25 - 22x54 Sideboard
or Counter Height Sideboard Table
- AD-DTB44/AD-CTB44 - 42x42 Square
Dining or Counter Height Dining Table
B
x1
2" Umbrella Grommet
A
C
For information on Care and Cleaning or to register your
highwood product, please visit www.highwood-usa.com.
PAGE 2 OF 2
high
wood
NATURE'S CLOSEST RIVAL
Lehigh, Weatherly, or Adirondack Collection
Rectangular, Square, or Sideboard Tables
Assembly Guide
All AD-DTB/AD-CTB
08.07.2017
A
1) Place the table top upside down on a soft surface.
2) Attach leg with 2 A bolts.
3) Repeat for each leg.
4) Securely tighten all bolts, but do not over tighten.
5) If installing an umbrella, insert
Umbrella Grommet B into center hole.
B
1
For information on Care and Cleaning or to register your
highwood product, please visit www.highwood-usa.com.
PAGE 1 OF 1
INCLUDED TOOLS
5/32" HEX KEY
IMPORTANT!
DO NOT fully tighten the bolts until all
bolts are started. Once all bolts are inserted,
go back & tighten all the bolts.
Retain these instructions for future reference
HARDWARE
high
wood
NATURE'S CLOSEST RIVAL
Weatherly Collection
Counter Chair with Arms
Assembly Guide
CHCW2
10.30.18
2) Place Assembly from
Step 1 onto Right Arm
Assembly. Attach Arm Assembly
to Seat Using Two "B" Bolts in
Front and One "C" Bolt in Rear.
Attach Arm to Back Using One "A" Bolt.
Install Foot Rests into Right Arm
Assembly and Fasten Using Two "B" Bolts.
A
B
C
1/4"-20 X 3"
1/4"-20 X 2"
1/4"-20 X 1.5"
x4
x8
x2
ALIGN ANGLES OF
BACK AND SEAT
1) Attach Chair Back
to Seat Using One
"A" Bolt in the Upper
Hole on Each Side.
BACK
A
A
SEAT
3) Insert Foot Rests into Left Arm Assembly
and Repeat Attachment Directions from Step 2
for Left Arm Assembly.
LEFT ARM ASSEMBLY
RIGHT ARM ASSMEBLY
B
A
C
B
B
FOOT REST
B
  • Page 1 1
  • Page 2 2
  • Page 3 3

Highwood AD-CNW44-ACE Operating instructions

Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI