Olympus 410 DIGITAL User manual

Brand: Olympus

Model: 410 DIGITAL

Category: Camera kits

Type: User manual

This manual is also suitable for

PREPARING THE CAMERA FOR USE

Before you begin using your Olympus Digital Camera…

a. Charging the battery

The Digital Camera uses an Olympus Lithium ion battery (LI-10B) and dedicated charger (LI-

10C). This is the only battery/charger designed for use with the Digital Camera. The battery

cannot be charged while in the camera.

Note: The Lithium ion battery is not fully charged when the camera is

purchased. You must fully charge the battery using the charger before first use.

• Insert the Lithium ion battery into the charger as indicated in the illustration.

• Connect the battery charger AC cable as shown to a standard wall outlet.

• To fully charge the battery requires approximately 2 hours. The charge indicator light will be red

when charging, and will turn green when the charging process is complete.

b. Loading the battery

Note: The battery and xD-Picture card compartments are accessed by opening the

respective compartment covers.

• Slide the battery compartment cover in the direction of the arrow, and lift

open the cover as shown in the illustration. (the direction indicated by the

mark on the cover)

• Insert the battery into the compartment.

• Close the battery compartment cover so that it pushes the battery in and

slide the cover while pressing the mark.

Note: If the battery compartment cover is hard to close, do

not force it. Press on the cover firmly to close the cover,

and then slide it into position.

• To remove the battery, make sure that the monitor and the lamp at the

side of the viewfinder are off. Return the camera to the upright position

and tip the battery out.

c. Inserting the xD-Picture Card

The xD-Picture Card is where the camera stores your pictures and

is available in a variety of memory capacities. The pictures you take

with the camera remain on the xD-Picture Card even when the

camera is turned off and/or the battery is removed.

• Open the connector cover while pressing the mark as in the illustration.

• Open the card cover by pulling the card cover catch towards you.

• Insert the xD-Picture Card into the spring-loaded card slot as shown in

the illustration. Push the card fully into the slot. The card will lock into

place when fully inserted.

• To remove, push the card all the way in to unlock it, then let it return slowly.

• Close the card cover before closing the connector cover.

• Press to close the connector cover.

Confirm you have installed the battery and xD-Picture Card properly by

pressing . The “NO PICTURE” message should be displayed in the

monitor. Turn the camera off by pressing again.

d. Attaching the strap (OPTIONAL)

Attach the strap as illustrated to make the camera easier to handle.

Charge indicator

TURNING ON THE CAMERA

All you need to do is slide the lens barrier open or close to turn the camera ON or OFF.

a. Turning the camera ON (SHOOTING MODE)

• Slide the lens barrier fully until it clicks. The lens extends.

• To turn the camera off, slide the lens barrier until you feel the first click. Wait until the lens is fully retracted, then

close the lens barrier all the way.

:To maximize battery life, the Digital Camera features a power saving mode in which the camera enters a sleep mode after

approximately three (3) minutes of non-use. Press the shutter button to wake up the camera.

b. Setting the Date and Time (OPTIONAL)

Set the date and time when using the camera for the first time. This affects the way image file names are

created, and will conveniently include this information with each picture.

• With the front lens barrier closed, press once. The monitor will turn on with “NO PICTURE” displayed in the

monitor. (The date and time can also be set when the camera is in the shooting mode.)

• Press to display the top menu.

• Press to select MODE MENU.

• Press to select SETUP, and then press .

• Press to select , and then press .

• Use to select the date format.

• Adjust the date and time in the appropriate fields by using to select the field, and to set the proper value.

Repeat this step until all date/time fields have been set.

Note: Time is entered using the 24-hour format.

• Press to store the date and time.

c. Camera Diagram and Controls

Now take a moment to familiarize yourself with the key areas of camera controls by reviewing the illustrations.

Power on

Power off

TIP

VIDEO OUT

jack

Card cover catch

Self-timer/

Remote control lamp

Flash

Remote control

receiver

USB

connector

Connector

cover

Lens barrier

Lens

DC-IN jack

cover

Card cover

Printed in China

UNPACKING THE BOX CONTENTS

Gather your Digital Camera and the parts as shown in the illustration. You’ll need these to complete the steps for the camera

set-up procedures that follow.

Camera Settings in Shooting Mode as shown in Monitor

Camera Settings in Playback Mode as shown in Monitor

Note: Depending on the camera settings, not all indicators will be displayed.

Viewfinder

Green lamp

Orange lamp

Monitor button (QUICK VIEW )

Monitor

OK/Menu button

Tripod socket

Shutter button Zoom button

Strap eyelet

Battery

component

cover

Arrow pad ( )

Shooting mode button

Self-timer button

Macro button Flash mode button

Speaker

2272*1704

Battery level

Green lamp

Flash stand-by

Flash mode

Macro mode

Memory gauge

Shooting mode

Exposure compensation

Recording sound

with still pictures

White balance

Spot metering

Image quality Number of storable still pictures/

Remaining recording time (movie)

AF target mark

DRIVE

Resolution

Self-timer/Remote control

2272

1704

$04.01.01 15:30

Battery level

Playback (Recording sound)

Protect

Image quality

Resolution

Exposure compensation

White balance

Date and time

File number (still picture)/

Frame number (still picture/movie)/

Total recording time (movie)

Print reservation (still picture)/

Movie play (playing back movies)

The following items are also included in the Digital Camera package: Basic Manual, A/V cable, RM-2 remote control, warranty card,

registration card (not provided in some areas).

Digital Camera Strap LI-10B lithium

ion battery

LI-10C

Battery charger

AC cable

for the battery

charger

CD-ROM

(CAMEDIA Master/

Reference Manual)

USB cable xD-Picture Card

QuickStart Guide

http://www.olympus.com/

VT693501

OLYMPUS AMERICA INC.

Two Corporate Center Drive, Melville,

NY 11747-3157, U.S.A.

http://www.olympusamerica.com/support

Olympus Europa GmbH

Wendenstrasse 14-18,

20097 Hamburg, Germany

http://www.olympus-europa.com/

START HERE

It is strongly recommended that you follow these step-by-step

numbered instructions to set up and quickly begin using your

new Digital camera.

For more detailed instructions on advanced features, please refer to

the printed Basic Manual included in your package, or the Reference

Manual on the CD-ROM.

d4199_qsge_6.fm Page 1 Thursday, December 4, 2003 10:29 AM

VIEWING AND

ERASING PICTURES

With a Digital Camera, you can easily view the photos you

want—and delete the ones you don’t.

a. Viewing Pictures

You can access the playback mode while the camera is

turned off, or while it is on in the shooting mode. In both

cases, just press the (QUICK VIEW) button once to

activate playback mode.

The last picture taken appears in the monitor. Use

to scroll though all the images saved on your xD-Picture

Card.

When you are finished reviewing your pictures:

• Press again to turn the monitor off when the camera is

turned off.

• Press the shutter button halfway or press again to

return to the shooting mode.

b. Erasing Pictures

The beauty of digital photography is your ability to keep

the photos you want, delete the rest, and reuse empty

memory space to take new pictures. This Digital Camera

offers two ways to permanently erase unwanted digital

photos:

Single-Frame Erase: Deletes only the picture currently

displayed in the monitor.

Once erased, pictures cannot be restored.

• With the lens barrier closed, press and use the arrow

pad to display the picture you want to erase.

•Press .

• Press to select .

• Press to select YES, and then press .

:Images can also be erased while in the “Quick View” mode

described in step 5a. This makes it easy to quickly erase a

picture that you just took.

All-Frame Erase: Deletes all pictures on the xD-Picture

Card in one operation, except for pictures you have

protected.

Once erased, pictures cannot be restored.

• With the lens barrier closed, press .

• Press , then press to select MODE MENU.

• Use to select the CARD tab, then press twice to

access the CARD SETUP screen.

• ALL ERASE should be highlighted. Press .

• As a safeguard, the Digital Camera will ask you to select

YES or NO to confirm erasing, as this process permanently

deletes all unprotected pictures. Select YES and press

TIP

TAKING PICTURES

There are two ways to compose your subject: using the

monitor or with the viewfinder. Depending upon the shooting

situation, there may be advantages to each method. Please

refer to the printed Basic Manual for more information.

a. Taking a Picture with the Monitor

• Open the lens barrier fully.

• Frame your subject using the monitor.

Icons representing camera settings appear on the

monitor, telling you important information such as the

Flash and record modes, battery life, and the number of

frames remaining.

• Press the shutter button halfway. The green lamp will light

steadily when the focus and exposure are set.

• Press the shutter button completely to take the picture. A

short beep confirms your picture has been taken.

b. Taking a Picture with the Viewfinder

• Open the lens barrier fully.

• Frame your subjects using the AF

target mark in the viewfinder.

• Press the shutter button halfway.

The Digital Camera confirms the focus and exposure are

properly set when the green lamp in the viewfinder lights

steadily.

• Press the shutter button completely to take the picture.

A short beep confirms your picture has been taken.

c. Zooming

This Digital Camera features a zoom lens, allowing you

to get closer to action, or capture wide-angle shots and

get everything into the picture.

• Push the zoom button W to zoom out and get everything

into the picture.

• Push the zoom button T to choose telephoto shooting and

get closer to the action.

d. Flash Modes

This Digital Camera features multiple flash modes.

Please note that not all flash modes are available

depending on the shooting mode selected.

With the shutter button depressed halfway, the flash is

ready to fire when the # indicator in the monitor or the

orange lamp next to the viewfinder lights. When the

orange lamp is blinking, the flash is charging.

e. Number of Storable Pictures

Your Digital Camera can handle xD-Picture Cards from

16 MB to 512 MB. The number of storable pictures

depends on the image quality selected. The default

quality mode is HQ mode. This mode allows you to

capture high quality images with medium file sizes. The

HQ mode is suitable for most shooting situations.

See the Camera Reference Manual on the CD-ROM for

complete descriptions of each recording mode and the

storable frame capacity for the various resolution modes

and xD-Picture Card capacities.

:To find out how many frames you have left, turn on the monitor

and look for the number in the lower right corner. Remember,

you can always delete unwanted pictures to make room for

more. (See Step 5.)

Orange lamp

Green lamp

Push to zoom out Push to zoom in

Icon Flash Mode Description

indication

Auto-flash The camera automatically decides if the flash is needed.

! Red-eye

Reduction Flash

Reduces incidence of red-eye by emitting pre-flashes to

shrink pupil size before firing the main flash. The strobe

effect is normal operation for this mode.

# Fill-in Flash The flash always fires with every picture.

$ Flash Off Turns the flash off for times when flash photography is

prohibited or not desired. The flash never fires.

TIP

INSTALLING THE CAMERA

SOFTWARE

You've now mastered the basic functionality of your new Olympus

Digital Camera! You are now ready to begin exploring the possibilities

that digital photography brings to your computer. Activities such as

photo editing, printing, and much more are only steps away!

About the Olympus CAMEDIA Master CD-ROM

Your Olympus Digital Camera comes bundled with a suite of software and documentation.

The CD includes:

• CAMEDIA Master: To download pictures from the camera, view, organize, retouch and print

your digital photos and movies.

• USB Driver for Windows 98: This utility must be installed to allow the camera to communicate

with your computer if it uses the Microsoft Windows 98 operating system.

• Olympus Digital Camera Reference Manual: A complete reference guide in digital form,

saved on the CD in PDF format.

You are now ready to install the computer software.

• Open the CAMEDIA Master CD-ROM package and locate the Software Installation Guide in

the language you wish to use.

• Continue to follow the step-by-step instructions for installing the software, and enjoy your new

digital photo processing capabilities!

CONNECTING THE CAMERA

TO A COMPUTER

:Olympus recommends using the optional AC adapter to ensure a consistent

power supply when downloading images.

Make sure that the camera is turned off before connecting it to

your computer.

Windows 98 users must install the “USB Driver for Windows 98”

software before connecting the Digital camera to the computer.

Refer to the Software Installation Guide for complete information.

TIP

Olympus makes it simple to connect the Digital camera to your

computer.

• Turn the camera off.

• Plug the supplied USB cable into the USB connector on your camera

and computer as illustrated at right.

• The camera turns on automatically and the green lamp next to the

viewfinder lights.

• Press to select PC, and then press on the USB screen.

The camera starts communicating with the PC.

EXIT

P C

USB

SELECT

Additional Camera Features

This Digital Camera offers a host of advanced features to expand your creativity. Here’s just a small sampling.

See the Basic Manual for details on these capabilities, and more!

• 10 Scene Program Shooting Modes: By using the virtual dial, you can easily select the camera settings

that most closely match your shooting situation.

• Sequential Shooting: Take a rapid succession of still pictures.

• Still Picture Editing: Edit still pictures and store them as new pictures.

• Macro Mode: For close-ups as tight as 0.7 ft. (0.2m), select Macro Mode.

• Movie Recording: Yes, this Digital Camera records movies with sound!

• Two-in-one Pictures: Combine two separate images taken in succession and store them as a single

picture.

• Close-up Playback: Enlarge the pictures in the monitor to check details of the selected image.

• Index Display: View several thumbnail pictures on the monitor at once.

• Protecting Pictures: Prevents you from accidentally erasing photos.

• Video Playback: View your pictures and movies on a television monitor.

• Panorama Shooting: Connect overlapping images into a single picture using the panorama mode and

Olympus Camedia Master software.

• Direct Printing: Connect directly to your PictBridge-compatible printer with the USB cable to print your

favorite images easily.

:Remember to complete and return your Registration Card (not provided in some areas), and keep all camera documentation

handy.

TIP

Technical Support (USA)

1-888-553-4448 (Toll-free)

8:00 AM - 10:00 PM ET

Monday - Friday

European Technical Customer Support

00800-67 10 83 00 (Toll-free)

+ 49 180 5 - 67 10 83 or +49 40 - 237 73 899

(Charged)

9:00 AM - 6:00 PM MET

Monday - Friday

d4199_qsge_6.fm Page 2 Thursday, December 4, 2003 10:29 AM

Olympus 410 DIGITAL User manual

Brand: Olympus

Model: 410 DIGITAL

Category: Camera kits

Type: User manual

This manual is also suitable for

Download PDF

report

Olympus 410 DIGITAL User manual

This manual is also suitable for

Olympus 410 DIGITAL User manual

Related papers

Other documents