Eti WP-78-850-MV User guide

WP-78-850-MV
Eti
Brand
Eti
Model
WP-78-850-MV
Type
User guide

This manual is also suitable for

USE AND CARE GUIDE
FULL CUTOFF WALL PACK
Questions, problems, missing parts?
Call ETiSSL Customer Service
8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754)
www.ETiSSL.com
THANK YOU
We appreciate the trust and confidence you have placed in ETi through the purchase of this LED light.
Visit us online to see our full line of products. Thank you for choosing ETi!
Ordering # 53307161
53308261
53308161
Part # WP-78-850-MV
WP-97-850-MV
WP-130-850-MV
Certification # 53307161
53308261
53308161
2
3 www.ETiSSL.com
Please contact 1-855-384-7754 or further assistance.
Table of Contents
Table of Contents ...................................2
Safety Information ..................................2
Warranty ..........................................2
Pre-Installation .....................................3
Planning Installation ...............................3
Tools Required ....................................3
Package Contents .................................3
Hardware Included .................................3
Installation ........................................4
Care and Cleaning ..................................7
Troubleshooting ....................................7
Safety Information
WARNING: Carefully read and understand the information
given in this manual before beginning the assembly and
installation. Failure to do so so could lead to electric shock,
fire, or other injuries which could be hazardous or even fatal.
WARNING: Ensure the electricity to the wires you are
working on is shut off. Either remove the fuse or turn off the
circuit breaker.
WARNING: This luminaire must be installed in accordance
with NEC or your local electrical code.
NOTICE: Do not use this fixture with a dimmer switch.
NOTICE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
□ Reorient or relocate the receiving antenna.
□ Increase the separation between the equipment and the receiver.
□ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
□ Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications not expressly approved
by the party responsible for compliance could void the user’s
authority to operate the equipment.
Warranty
This product is warranted for a period of 5 years from the date of original purchase against defects in materials and workmanship. If this
product should fail to operate due to defects in material or workmanship within 60 months of purchase, see www.ETiSSL.com for details.
This product will be repaired or replaced, at ETi’s option. This warranty is expressly limited to repair or replacement of product and liability
for direct, incidental, or consequential damages is hereby expressly excluded. Some states do not allow exclusions of direct, incidental or
consequential damages, so the above limitation of exclusion may not apply to you. This warranty gives the consumer specific legal rights,
which vary from state to state.
WARRANTY IS VOID IF PRODUCT IS NOT USED FOR THE PURPOSE WHICH THIS PRODUCT IS MANUFACTURED.
Pre-Installation
PLANNING INSTALLATION
Before beginning assembly, installation, or operation of the product, make sure all parts are present. Compare parts with the package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble, install, or operate the product.
Contact Customer Service for replacement parts.
NOTE: Keep your receipt and these instructions for proof of purchase.
WARNING: This luminaire must be installed in accordance with the NEC or your local electrical code. If you are not familiar with these codes
and requirements or with electrical installations, we recommend you contact a qualified electrician to do the installation.
TOOLS REQUIRED
Wire
Strippers
Safety
Goggles
Ladder Gloves
Silicone
sealant
Phillips
Screwdriver
Power drill
with 1/8
drillbit
Electrical
Tape
PACKAGE CONTENTS
Part Description Quantity
A Fixture Plate 1
B Lens Cover 1
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
Part Description Quantity
AA Electrical Box Screw 4
BB Drywall Anchor 4
CC Mounting Screw 4
DD Wire Connector 3
EE Gasket 1
A
AA BB CC
DD EE
B
4
5 www.ETiSSL.com
Please contact 1-855-384-7754 or further assistance.
1
Separating the lens cover from
the fixture plate
□ Remove the two screws at the top of the wall pack
that attach the lens cover to the fixture plate (A).
□ Remove the lens cover (B) from the fixture plate (A)
by rotating the lens cover (B) down and sliding it to
the right to remove it from the pegs.
3
Marking the location of the
fixture
□ Place the fixture plate (A) in the desired location.
□ Use a pencil to mark the locations of the mounting
holes, which are approximately 12 9/16 inches
apart horizontally and 6 5/16 inches apart
vertically.
□ Set the fixture plate (A) aside until ready to attach
to the mounting surface in a later installation step.
□ Drill a 1/4-in. pilot hole into each of the screw
locations marked on the mounting surface. You can
also use an awl or nail to dimple the screw holes.
□ If mounting the fixture plate (A) to drywall, install a
drywall anchor (BB) in each drilled mounting hole.
NOTE: The drywall anchors (BB) are only to be used for mounting the fixture to plaster or drywall surfaces.
NOTE: Mounting Screws are suitable for wood and concrete mounting also.
2
Preparing the fixture plate for mounting
□ Use a power drill to drill through the mounting holes on the
fixture plate (A).
□ Align the fixture plate (A) mounting template with the electrical
box to determine which knock outs to remove for mounting.
□ Drill out the required knock outs with a power drill.
Installation
WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the
circuit breaker before removing the existing light fixture or installing the new one.
With power disconnected to the electrical box, remove the existing fixture. Make a sketch of how the current fixture is wired (by wire color)
or mark the wires with masking tape and a pencil so you will know how to properly reconnect the wires to the new LED light fixture.
Installation (continued)
12 9/16 in.
BB
1.37 in.
1/4 in.
6 5/16 in.
A
12 9/16 in.
6 5/16 in.
4
Feeding wires through the knock
out holes
□ Place the gasket (EE) on the back of the fixture plate (A).
□ Feed the wires from the electrical box through the
desired knock out hole.
CAUTION: If using a top, bottom, or side knock out
hole, use a 1/2 in. watertight connector and conduit (not
included).
5
Mounting the fixture
□ Align the holes drilled in the mounting template on the
fixture plate (A) with the mounting holes on the electrical
box.
□ Align the 4 mounting holes on the fixture plate (A) with the
4 pilot holes drilled in the mounting surface.
□ Insert the 4 electrical box screws (AA) and tighten to
secure the fixture plate (A) to the electrical box.
□ Insert the 4 mounting screws (CC) and tighten to secure
the fixture plate (A) to the wall.
6
Making the electrical connections
□ Slide the holes in the bottom of the lens cover (B) over the pegs at the
bottom of the fixture plate (A).
□ Connect the hot and neutral (black and white) wires from the electrical box
to the same color wires from the fixture plate (A).
□ Connect the green ground wire from the electrical box to the green ground
wire from the fixture plate (A).
□ Cover the wire connections using the wire connectors (DD).
□ Wrap the wire connectors (DD) with electrical tape for a more secure
connection.
□ Connect the green ground wire from the fixture plate (A) with the quick
connector attached to the green ground wire from the lens cover (B) with
the quick connector attached.
□ Connect the red and blue wires from the fixture plate (A) with the quick
connector attached to the red and blue wires from the lens cover (B) with the
quick connector attached.
DD
A
CC
EE
A
A
B
Screws
Mounting
Holes
A
Mounting Holes
A
B
Mounting
Template
AA
6
7 www.ETiSSL.com
Please contact 1-855-384-7754 or further assistance.
Installation (continued)
Care and Cleaning
CAUTION: Before attempting to clean the fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from the
fuse box.
□ Clean the fixture with a soft, dry cloth.
□ Do not use cleaners with chemicals, solvents, or harsh abrasives.
□ Do not use liquid cleaner on the LEDs, LED driver, or wiring inside the light fixture.
Troubleshooting
WARNING: Before doing any work on the fixture, disconnect power to the light fixture.
Minor problems often can be fixed without the help of an electrician.
Problem Possible Cause Solution
The fixture will not light. The power is off. Ensure the power supply is on.
The circuit breaker is off. Ensure the circuit breaker is in the on position.
There is a bad connection. Check to ensure proper wire connections are made.
Contact a qualified electrician.
There is a defective switch. Contact a qualified electrician.
The fuse blows or the circuit breaker
trips when the light is turned on.
The wires are crossed or the power
wire is grounding out.
Check the wire connections.
Contact a qualified electrician or call customer
service 1-855-384-7754.
7
Securing the lens cover to the
fixture plate
□ Rotate the lens cover (B) up to align the two screw
holes at the top of the lens cover (B) with the screw
holes at the top of the fixture plate (A).
□ Tighten the screws until the lens cover (B) is secure.
□ Restore power at the electrical panel.
□ Turn on the light switch to activate the fixture.
B
8
Using silicone sealant between the
wall and the fixture plate
□ To ensure a watertight seal, apply silicone caulk (not
provided) around the back edges of fixture plate (A).
A
B
A
Questions, problems, missing parts?
Call ETiSSL Customer Service
8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754)
WWW.ETISSL.COM
Retain this manual for future use.
GUIDE D’UTILISATION ET D’ENTRETIEN
APPLIQUE MURALE DIRECTIONNELLE
Questions, difficultés, pièces manquantes?
Téléphonez au service à la clientèle de ETiSSL
8 h - 17 h, HNC, du lundi au vendredi.
1-855-ETI-SSLI (1-855-384-7754)
www.ETiSSL.com
MERCI
Nous apprécions la confiance que vous avez accordé à la ETi Solid State Lighting, Inc. en achetant ce luminaire à DEL.
Consultez notre gamme complète de produits en ligne. Nous vous remercions d’avoir choisi ETi!
N° de commande 53307161
53308261
53308161
N° de pièce WP-78-850-MV
WP-97-850-MV
WP-130-850-MV
N° de certification 53307161
53308261
53308161
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Eti WP-78-850-MV User guide

WP-78-850-MV
Eti
Brand
Eti
Model
WP-78-850-MV
Type
User guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents