Bosch SGI5924/21 User manual

Page is loading ...

de

Inhaltsverzeichnis

Sicherheitshinweise 3. . . . . . . .

Gerät kennen lernen 5. . . . . . .

Enthärtungsanlage 5. . . . . . . .

Spezialsalz einfüllen 6. . . . . . .

Klarspüler einfüllen 7. . . . . . . .

Nicht geeignetes Geschirr 8. .

Geschirr einordnen 9. . . . . . . .

Reiniger 12. . . . . . . . . . . . . . . . . .

Programmübersicht 14. . . . . . . .

Geschirrspülen 15. . . . . . . . . . . .

Zusatzfunktionen * 17. . . . . . . . .

Wartung und Pflege 17. . . . . . . .

Fehlersuche 19. . . . . . . . . . . . . .

Kundendienst rufen 21. . . . . . . .

Hinweise 22. . . . . . . . . . . . . . . . .

Installation 23. . . . . . . . . . . . . . . .

en

Index

Safety instructions 25. . . . . . . . .

Getting to know your dishwasher 27

Water softener 27. . . . . . . . . . . .

Filling the special salt container 28

Filling the rinse-aid container 29

Unsuitable dishes 30. . . . . . . . .

Arranging crockery, glasses,

etc. in the dishwasher 31. . . . . .

Detergents 34. . . . . . . . . . . . . . .

Programme overview 36. . . . . .

Washing dishes 37. . . . . . . . . . .

Additional functions * 39. . . . . . .

Maintenance and care 39. . . . . .

Fault finding 41. . . . . . . . . . . . . .

Customer Service 43. . . . . . . . .

Information 44. . . . . . . . . . . . . . .

Installation 45. . . . . . . . . . . . . . . .

fr

Sommaire

Consignes de sécurité 47. . . . . .

Présentation de l’appareil 49. . .

Installation d’adoucissage 49. .

Remplissage du sel spécial 50.

Remplissage du liquide de rinçage 51

Vaisselle non-adaptée 52. . . . . .

Classement de la vaisselle 53. .

Détergent 57. . . . . . . . . . . . . . . .

Tableau des programmes 59. . .

Laver la vaisselle 60. . . . . . . . . .

Fonctions

supplémentaires * 62. . . . . . . . .

Entretien et maintenance 62. . .

Détection des pannes 64. . . . . .

Appeler le service après-vente 66

Remarques 67. . . . . . . . . . . . . . .

Installation 68. . . . . . . . . . . . . . . .

nl

Inhoud

Veiligheidsvoorschriften 70. . . .

Kennismaking met het apparaat 71

Wateronthardingsinstallatie 72.

Zout bijvullen 73. . . . . . . . . . . . .

Vullen met glansspoelmiddel 74

Ongeschikt servies 75. . . . . . . .

Serviesgoed sorteren 76. . . . . .

Afwasmiddelen 79. . . . . . . . . . . .

Programma-overzicht 81. . . . . .

Afwassen 82. . . . . . . . . . . . . . . .

Extra functies * 84. . . . . . . . . . . .

Schoonmaken en onderhoud 84

Opsporing van storingen 86. . . .

Inschakelen van de Servicedienst 88

Aanwijzingen 89. . . . . . . . . . . . .

Installatie 90. . . . . . . . . . . . . . . . .

Page is loading ...

en

25

Safety instructions

Delivery

Immediately check the packaging and

dishwasher for any damage which may

have been caused in transit. Do not use

a damaged appliance, but consult your

supplier.

Please dispose of packaging material

properly.

The corrugated cardboard consists

mainly of waste paper.

The polystyrene moulded parts have

been foamed without any CFCs.

The polyethylene film (PE) consists

partly of secondary raw material.

The wooden frames (if fitted) are made

of residual wood and are untreated.

The hoops (if fitted) consist of

polypropylene (PP).

Installation

Install and connect the appliance

according to the installation and

assembly instructions.

The dishwasher must NOT be

connected to the power supply during

installation.

Ensure that the protective conductor

system of the domestic electricity

supply has been installed correctly.

Electrical connection conditions must

correspond with the specifications on

the rating plate of the dishwasher.

Built-under and built-in appliances

should always be installed under a

continuous work surface which is

attached to the adjacent cupboards, in

order to ensure that the appliance is

entirely stable.

After the appliance has been installed,

the mains plug should still be easily

accessible.

Not on all models:

The plastic housing on the water input

contains an electrically operated valve.

The connecting wires are inside the

inlet hose. Do not cut through this hose

and do not immerse the plastic housing

in water.

Warning

For safety reasons, if the appliance is not

fitted in a recess, thereby making a side

wall accessible, the door hinge area

should be covered at the side.

(Risk of injury)

Covers are available as optional

accessories from customer services or

specialist stores.

en

26

During normal use

Warning

Knives and other utensils with sharp points

must be loaded in the basket with their

points down or in a horizontal position.

Use the dishwasher solely in a

domestic environment and for its

designated purpose: washing

household tableware and other utensils.

Do not place any heavy objects or

stand on the door when it is open. The

appliance could tip forward.

The water inside the dishwasher is not

suitable for drinking.

Do not use solvents of any kind inside

your dishwasher. They could cause an

explosion.

Open the door very carefully if the

dishwasher is operating. There is a risk

of water squirting out.

If your family includes children

Do not permit small children to play with

or operate the dishwasher.

Keep children away from detergents

and rinse-aids.

Keep small children away from the

open door of the dishwasher. There

could still be some detergent left inside.

Child lock *

* on applicable models

Please refer to the drawings enclosed in

the envelope

40 Engaging the child lock

41 Opening the door with the child lock

engaged

42 Disengaging the child lock

If a fault occurs

Repairs or other work on the

dishwasher should only be carried out

by a qualified specialist.

The dishwasher must be disconnected

from the electricity supply before any

repairs or other work are started. Pull

the mains plug out of the wall socket or

switch off at the fuse box. Grasp the

plug to remove it from the socket; do

not tug on the cable. Turn the water off

at the tap.

When disposing of old

appliances

Appliances that have reached the end

of their service life should be rendered

inoperable in order to exclude the

possibility of subsequent accidents. Pull

the mains plug out of the wall socket,

cut through the connecting cable and

disable the door lock.

Take the appliance to a designated

waste disposal centre.

Warning

Children could get locked in the appliance

(risk of suffocation) or get stuck in other

positions.

Therefore: Remove the mains plug, cut the

mains wire and set aside. Damage the

door lock so that the door can no longer

be closed.

en

27

Getting to know your

dishwasher

Illustrations of the control panel and the

interior of the dishwasher are shown on

the rear fold-out cover of this manual. Fold

this page out before you read the manual.

Control panel

1 Main switch

2 Time delay

3 Digital display/

Programme progress indicator

4 Salt refill indicator

5 Rinse-aid refill indicator

6 Door opener

7 Programme buttons

8 Additional functions *

* some models only

Appliance interior

20

Upper basket with 2-tiered cup rack

21

Additional cutlery basket for the top

basket *

22

Upper spray arm

23

Lower spray arm

24

Container for special salt with level

indicator *

25

Filters

26

Cutlery basket

27

Lower basket

28

Locking mechanism

29

Container for rinse-aid, with level

indicator

30

Detergent compartment

31

Nameplate

* not on all models

You will need to purchase the

following before using the

dishwasher for the first time:

– special salt for use in dishwashers

– detergent

– rinse-aid

Only use products, which are suitable for

dishwashers.

Water softener

In order to rinse dishes and glasses

satisfactorily, the dishwasher requires soft

water, i.e. containing little or no lime,

otherwise water stains will be left behind

on crockery and glasses, etc.

If the tap water exceeds a certain level of

hardness, it must be softened, i.e.

decalcified, so that it can be used in the

dishwasher.

This is achieved by adding a special salt

to the water softener inside the

dishwasher.

The water softener, that is the required

amount of salt, is set up according to how

hard the tap water is.

Setting up the water softener

(see introduction)

en

28

Filling the special salt

container

How the salt works

While washing is taking place, salt is

automatically rinsed out of the salt

container into the water softener where it

dissolves the lime in the water.

The dissolved lime is pumped out of the

dishwasher. The water softening system is

then ready for the next load.

This process of regeneration can only

function when the salt is dissolved in

water.

Unscrew the lid on the salt container

24 .

Before you use the dishwasher for the first

time, pour approx. 1 litre of water into the

salt container.

Use the enclosed salt filler.

Refill with salt (do not use edible salt)

until the salt dispenser is full (max. 1.5 kg).

When the salt dispenser is being refilled,

water is displaced and drains away.

Therefore always refill the salt dispenser

immediately before switching on the

dishwasher (to prevent corrosion). As a

result, the overflowing salt solution will be

immediately diluted and rinsed out. Then

remove salt residue from the filler area and

screw on the dispenser cover, ensuring

that it is not fitted askew.

The LOW SALT indicator

4

on the front

panel will light up initially but will extinguish

again after a short period when the salt

solution has become sufficiently

concentrated.

Note

When the control is set to

, it is

not necessary to fill up with salt

as none will be consumed while

the dishwasher is operating. The

LOW SALT indicator is switched

off. If the control is set between

and , then salt must be

added to the dispenser.

Do not pour detergent into the

container for special salt. This

would destroy the water

softener.

Salt refill indicator

As soon as the salt refill indicator 4 is lit

on the control panel, refill with salt

immediately before the next rinse cycle.

en

29

Filling the rinse-aid

container

The purpose of a rinse-aid is to prevent

the formation of water marks on tableware

and utensils, and to ensure that glasses

are clean and sparkling. The rinse-aid is

consumed during the washing process.

Fold back the lid on the rinse-aid

container

29 .

To open the lid, press the mark

on

the rinse-aid lid and simultaneously lift

the lid off the lug

.

Pour the rinse-aid into the filler hole

until the level indicator turns dark.

Close the lid, ensuring that you hear it

snap closed.

Note

Use only rinse aid for domestic

dishwashers. Spilt rinse aid

may result in excessive foam

formation in the next rinse

cycle. Therefore, remove any

spilt rinse aid with a cloth.

Adjusting the amount of

rinse-aid

The amount of rinse-aid added to the

water can be varied by adjusting the

stepless control. The rinse-aid control has

been set to ”4” in the factory.

Do not alter the setting of the rinse-aid

control unless streaks (turn knob towards

”–”) or water marks (turn knob towards ”+”)

are left on the dishes.

29

rinse–aid control

Low rinse-aid indicator

As long as the rinse-aid refill indicator on

the panel

5 (on applicable models) or

dispenser

29 has not illuminated, there is

sufficient rinse-aid in the dishwasher.

LOW RINSE-AID indicator

en

30

Unsuitable dishes

You should not clean the

following items in your

dishwasher:

Cutlery and dishes made of wood. They

will leach out and become unsightly; the

utilised adhesives are also not suitable

for the dishwasher temperatures.

Delicate décor glasses, craft dishes and

vases, special antique or irreplaceable

dishes. These décor items are not

dishwasher-safe.

Plastic parts, copper and tin dishes

sensitive to hot water are not suitable

either. Overglazed patterns, aluminium

and silver parts tend to become

discoloured and fade during the rinsing

cycle. Even some types of glass (e.g.

crystal glass objects) may become cloudy

after many rinse cycles. Completely

absorbent materials, such as sponges and

cloths must not be cleaned in the

dishwasher either.

Recommendation:

In future buy only dishes which are

identified as dishwasher-safe.

Note

Dishes which are soiled with

ash, wax, lubricating grease or

ink must not be cleaned in the

dishwasher.

Damage to glassware and other

dishes

Possible causes:

type of glass or manufacturing process

chemical composition of detergent

water temperature and duration of

dishwasher programme.

Suggested remedy:

Use glassware or porcelain dishes that

have been marked ’dishwasher–proof’

by the manufacturer.

Use a mild detergent that is described

as ’kind to dishes’. If necessary, seek

further information from detergent

manufacturers.

Select a programme with as low a

temperature and as short a duration as

possible.

To prevent damage, take glass and

cutlery out of the dishwasher as soon

as possible after the programme has

ended.

en

31

Arranging crockery, glasses,

etc. in the dishwasher

Loading the dishwasher

Scrape off any large amounts of left-over

food. It is not necessary to rinse the dishes

under running water.

Place objects in the dishwasher in such a

way that

items such as cups, glasses, pots/pans,

etc. are stood upside down,

curved items, or those with recesses,

should be at a slant so that water can

run off,

they are stacked securely and cannot

tip over,

they do not prevent the spray arms from

rotating while washing takes place.

Very small items should not be washed in

the dishwasher as they could easily fall out

of the baskets.

Removing the dishes

To prevent water dripping from the top

basket onto the dishes in the lower basket,

we recommend that you empty the lower

basket first and then the top basket.

Cups and glasses

Upper basket 20

* on applicable models

Pots and pans

Lower basket 27

Cutlery

Cutlery should always be inserted in

random order with the handles pointing

downwards (take care with knife blades!).

This enables the jet of water to reach the

individual items more easily.

To prevent the risk of injury, place long and

pointed implements and knives on the

shelf (some models) or knife shelf

(available as an accessory).

Folding spikes *

* on applicable models

To improve stacking of pots and pans, the

spikes can be folded down.

en

32

Spray head for baking sheets *

* on applicable models

Please refer to the drawings enclosed in

the envelope

Large baking sheets or grids can be

cleaned with the aid of the special spray

head. Remove the top basket and attach

the spray head as shown in the drawing.

Arrange the baking sheets as illustrated,

so that the jet of water can reach all parts

of them (max. 4 baking sheets and

2 grids).

Knife rack *

* on applicable models

Shelf *

* not on all models

Lean tall glasses and those with long

stems against the shelf – not against other

items to be washed.

Long items, serving cutlery, salad servers

or knives should be placed on the shelf so

that they do not obstruct the rotation of the

spray arms. The shelf can be folded back

when not required for use.

Adjusting position of basket *

* not on all models

86cm

81cm

Ø max.

30/*25cm

Ø max.

20/*25cm

Ø max.

34/*29cm

Ø max.

20/*25cm

If required, the height of the top basket can

be adjusted in order to create more space

for large utensils either in the top or bottom

basket.

Select one of the two following procedures

according to the design of the top basket

for your appliance model:

en

33

Top basket with upper

and lower roller pairs

Pull out the top basket.

Remove the top basket and re-attach it

to the upper or lower rollers.

Top basket with side levers

(Rackmatic)

Pull out the top basket.

To lower the basket, press in

succession the two levers on the left

and right sides of the basket. Always

take hold of the side of the basket on

the upper edge, otherwise the basket

will not drop smoothly (and may

damage the utensils).

To raise the basket, take hold of the

basket on the upper edge and pull

upwards.

Before you re-insert the basket, ensure

that it is at the same height on both

sides. Otherwise, the appliance door

cannot be closed and the upper spray

arm will not connect to the water circuit.

en

34

Detergents

Information about detergents

You can use any brand of liquid or powder

detergent, as well as tablets, that have

been specifically designed for use in

domestic dishwashers. (Do not use normal

washing-up liquid!)

Nowadays there are three types of

dishwasher detergent available:

1. those containing phosphates and

chlorine,

2. those containing phosphates but no

chlorine,

3. those containing neither phosphates

nor chlorine.

When a phosphate-free detergent is used

in conjunction with hard water, there is a

greater possibility that white marks will be

left behind on crockery and glasses, etc.

These can be avoided by pouring an

increased amount of detergent into the

dispenser.

Chlorine-free detergents have a reduced

bleaching effect. This can mean that tea

stains are not completely removed or

plastic items become discoloured.

This can be resolved by:

– selecting a higher temperature

programme, or

– increasing the amount of detergent, or

– using a detergent that contains chlorine.

Check the label on the detergent

packaging to determine whether a

particular product is suitable for use with

silverware.

If you have any further questions, we

recommend that you contact the customer

advice departments of the various

detergent manufacturers.

Detergent compartment with

measuring marks

The side of the detergent compartment is

marked with lines to help you determine

how much powder to add.

The capacity of the detergent container is

15 ml up to the bottom line and 25 ml up to

the middle line. When the compartment is

full it contains 40 ml.

40 ml

25 ml

15 ml

Important

If the lid on the detergent com-

partment is closed, press the

release lever to open the flap.

Adding detergent

Tip detergent powder into the

corresponding compartment

30 .

Please observe the manufacturer’s

instructions printed on the detergent

packaging when determining the

correct dosage.

When you select the INTENSIVE

programme, tip an extra 10–15 ml of

detergent onto the inside surface of the

door.

en

35

Reduce costs!

If you are using the upper rack

only, or if your dishes are only

moderately dirty, it will normally

suffice to employ a reduced

amount of detergent than

otherwise recommended.

Close the lid on the detergent

compartment.

Press down the lid (1) until it clicks

shut (2).

If you are using detergent in tablet form,

read the manufacturer’s

recommendations on the packaging in

order to

determine where the tablets should be

placed inside the dishwasher (e.g. in

cutlery basket, detergent compartment,

etc.).

Make sure that the lid on the detergent

compartment is closed, even if you are

using tablets.

CAUTION

IMPORTANT NOTE

ON THE USE OF

COMBINED CLEANING

PRODUCTS

Please note the following when using

”combined cleaning products” which

eliminate the need for a rinsing agent or

salt, for example:

Some products with a built-in rinsing

agent are only used to their full effect in

certain programmes.

This type of product does not generally

produce the desired effect with

automatic programmes.

Products which eliminate the need for

regeneration salt can only be used

within a certain water hardness range.

If you wish to use these combined

products, please read the instructions

carefully and heed any notes on the

packaging.

Contact the manufacturer of the cleaning

agent if you have any questions,

particularly if:

the crockery is very wet once the

programme has finished.

limescale deposits are formed.

Any problems which arise as a direct

result of the use of these products are not

covered by our warranty.

en

36

Programme overview

This overview lists the max. possible number of programmes. The programmes supplied with your

appliance are indicated on the fascia.

Type of crockery

e.g.china,

pots/pans,

cutlery,

glasses,

etc.

Type of food

remains

Amount of

food remains

Condition of

food remains

Wash

programme

Programme

sequence

Nondelicate

Soups, casseroles,

sauces, potatoes,

pasta, rice, eggs,

roast or fried food

Soups, potatoes,

pasta, rice, eggs,

roast or fried food

Coffee, cakes,

milk, sausage,

cold drinks,

salads

a lot

very little

stuck

on hard

Auto

55° ⁄65°

Intesive

70°

Eco

50°

Quick

35°

Pre-rinse

Rinse-aid

70°

Drying

Main rinse Main rinse

Rinse-aid

55°

Wash

35°

Rinse-aid

65°

Wash

50°

Rinse off if

the dishes

have been

stacked for

several

days in the

dishwasher

prior to

washing.

Pre-rinse

Mixed Delicate Mixed

Gentle

40°

Pre-rinse

Wash

40°

Main rinse

Rinse-aid

55°

Drying

a little

loosely attached

Third

rinse

Pre-rinse

50°

Wash

70°

First rinse

Second

rinse

medium

The programme sequence is

optimized and adapted with how

the appliance is loaded and how

dirty the dishes are.

Pre-rinse

Programme selection

The most appropriate programme can be

identified by comparing the type of

crockery, cutlery, etc., as well as the

amount and condition of food remains,

with the details contained in the

programme overview.

You will find the appropriate programme

information in the introduction.

en

37

Washing dishes

Reduce costs!

If only a small number of

dishes have been loaded into

the dishwasher, selecting a

programme that operates at

the next lowest temperature

will usually suffice.

Programme data

The stated programme data are based on

standard operating conditions. The values

can vary considerably according to:

different amounts of dishes

temperature of mains water supply

pressure of mains water supply

ambient temperature

fluctuations in mains voltage

machine-related factors (e.g.

temperature, water volume, ...).

Energy and water consumption is reduced

by up to 1/4 when dishes are washed in

the upper basket only.

Water consumption values are based on a

water hardness setting of 4.

Aquasensor

The Aquasensor is an optical measuring

device with which the cloudiness of the

water in the dishwasher is measured. A

photoelectric sensor is used to detect the

degree of soiling in the water, caused by

dissolved food particles such as egg, fat

and rolled oats, etc.

The Aquasensor functions during all

programmes that include a pre-rinse cycle.

If the water is still “clean” at the end of the

pre-rinse cycle, then the same water is

used for the following wash cycle. If the

water is dirty, it is pumped out of the

dishwasher and replaced by fresh water.

The effect is to reduce water consumption

by approx. 4 litres when the dishes are

only “slightly” dirty.

Switching the dishwasher ON

Set main switch 1 to ON.

Indicators light up according to the last

programme that was selected.

This same programme will run again if

no other programme button

7 is

pressed.

The programme starts automatically.

End of programme

The programme has ended when a figure

appears in the numerical display 3 .

Switching the dishwasher OFF

Several minutes after the programme has

ended:

Set the main switch 1 to OFF.

Turn the water tap off.

(Does not apply when Aqua-Stop unit

has been fitted)

Remove dishes, etc. when they have

cooled down.

Interrupting the programme

Set main switch 1 to OFF.

Indicator lights extinguish. The

programme is retained in the

dishwasher memory.

If the hot water was switched ON or the

appliance has already heated up and

then the appliance door opened, leave

the door ajar for several minutes and

then close.

Otherwise, the appliance door may fly

open due to expansion.

In order to continue with the stored

programme, set the main switch to ON

again.

en

38

Programming the timer

You can delay the start of a programme in

increments of one hour for up to 19 hours.

Switch dishwasher ON.

Immediately press the TIMER button

2 . The numerical display 3

changes to .

Press the TIMER button as many times

as necessary until the numerical display

shows the required delay.

To erase the time delay setting, keep

pressing the TIMER button until

appears in the numerical display.

You can change your programme

selection as often as you like during the

intervening period before the dish-

washer starts up.

Time-remaining indicator

The time-remaining indicator is

self-learning. When the programme

begins, it displays the estimated duration

of that programme. This figure is based

upon the duration of the previous

programme, or if the dishwasher is being

used for the first time, the duration of the

programme used for testing the appliance

in the factory. While the programme is

running, the indicator shows the amount of

time before the programme ends. The time

remaining is also adjusted to account for

the temperature of the water supply and

the number of dishes.

Intensive drying function

Activating the intensive drying function

increases the temperature during the

rinse-aid stage which gives better drying

results.

Press and hold the A programme

button, and set the main switch

1 to

ON.

Release both buttons.

Either (ON) or (OFF) flashes in

the numerical display

3 .

Press the A programme button to

change the setting.

Set the main switch 1 to OFF. The

new setting is stored in the dishwasher

memory.

Cancel programme (Reset)

Only when the master switch is ON.

Press the

A and C buttons

simultaneously, and hold them pressed

for approx. 3 seconds.

The numerical display shows

.

Close the door.

The programme continues for approx.

1 min.

When it has ended, set the main switch

1 to OFF.

Close the detergent compartment 30 .

To restart the dishwasher, set main switch

1 to ON again and select desired

programme.

Changing the programme

It is possible to change the programme

within 2 minutes after you have switched

the dishwasher on.

Should it be necessary to change the

programme after this period, the

programme cycle that has already been

begun (e.g. washing) will be completed

first of all.

The new remaining time displayed is the

sum of the remaining time from the

preceding programme cycle and the

remaining time attributable to the new

programme that has been selected.

en

39

Additional functions *

* on applicable models

Pre-Soak *

The Pre-Soak programme option serves to

perform a pre-soak cycle before the main

programme. This cycle enables cookware,

e.g. pans, bowls, etc. to be pre-soaked

and pre-rinsed in the lower rack. If you

wish to pre-soak the dishes, this

programme option must be selected by

pressing the “Pre-Soak” button before the

programme starts. The recommended

detergent amount is approx. 5 g poured

onto the inside of the door.

Quick *

Pressing the “Quick” button provides a

short wash cycle by curtailing the drying

phase and the washing time. The washing

and drying performance will be reduced

with the Quick programme option.

Washing contents of UPPER

RACK only *

If you have a small number of dishes to

wash in the upper rack (e.g. glasses, cups,

plates), switch on the UPPER RACK

function. If you select the UPPER RACK

function, the lower rack must be empty.

Add a reduced amount of detergent

compared to that which is recommended

for a full load.

Washing contents of

LOWER RACK only *

If you have a small number of dishes to

wash in the lower rack (e.g. plates, pans,

bowls), switch on the LOWER RACK

function. If you select the LOWER RACK

function, the upper rack must be empty.

Add a reduced amount of detergent

compared to that which is recommended

for a full load.

Maintenance and care

You can help prevent faults by checking

and maintaining your appliance regularly.

This will save time and reduce problems.

Therefore you should occasionally

examine the inside of your dishwasher.

Overall condition of the

appliance

Check the rinsing compartment for grease

and limescale deposits.

If you find any deposits:

Fill the detergent dispenser with

detergent. Start the empty appliance

with the programme which has the

highest rinsing temperature.

Clean the door seal:

Wipe the door seal regularly with

a damp cloth and remove any deposits.

Special dishwasher salt

Check the LOW SALT indicator 4 . Top

up with salt, if required.

Rinse-aid

Check the LOW RINSE-AID indicator 5

on the front panel or the level indicator on

the rinse-aid container

29 . Top up with

rinse-aid, if required.

Filters

The filters 25 prevent larger remnants of

food or other objects from getting inside

the pump. This residue can occasionally

clog up the filters.

The filter system consists of a filter

cylinder, a flat fine filter and, depending on

the model, a microfilter (*).

Inspect the filters for obstructions every

time the dishwasher has been used.

By unscrewing the filter cylinder, you

can remove the filter system. Remove

any food remnants and clean the filters

under running water.

en

40

Reassembly:

Insert the filter system and screw down

with the filter cylinder.

Spray arms

Lime and remnants of food in the washing

water can block the nozzles in the spray

arms 22 and 23 and the arm

mountings .

Inspect the nozzles in the spray arms

for blocked holes due to remnants of

food.

If necessary, pull the lower arm 23

upwards and lift it off.

Unscrew the upper spray arm 22 .

Clean both spray arms under running

water.

Refit the spray arms. Ensure that the

lower arm has locked into place and the

upper one is screwed tight.

0

1

2

3

Spray arms

en

41

Fault finding

Resolving minor problems

yourself

Experience has shown that you can

resolve most problems that arise during

normal daily usage yourself, without

having to call out a service engineer. Not

only does this save costs, but it also

means that the appliance is available for

use again that much sooner. The following

list of common occurrences and their

remedies should help you identify the

causes of most problems.

Problems ...

... when the appliance

is switched on

The appliance does not start.

The mains fuse has tripped.

The appliance plug has not been

inserted.

The appliance door has not been

shut properly.

The tap has not been turned on.

The filter on the water supply hose

is blocked.

Switch off the appliance and pull

out the mains plug. Turn off the

tap. Then clean the filter which is

situated at the connection of the

supply hose. Finally, restore the

power, turn on the tap and switch

on the appliance.

Warning

Remember:

The appliance may be repaired

by a technician only. Improper

repairs may cause

considerable damage and/or

injure the user.

... with the appliance itself

Lower spray arm rotates with

difficulty

Spray arm is blocked by small

items or food remains.

Lid in detergent compartment

cannot be closed

Detergent compartment has been

overfilled.

Mechanism is clogged with

remnants of detergent.

Indicator lamps do not extinguish

after washing has finished.

Indicator lamps do not extinguish

after washing has finished

Main switch is still set to ON.

Remnants of detergent stuck inside

dispenser

Compartment was damp when it

was filled up with detergent.

Compartment must be dry before

detergent is added.

Water remains inside appliance

after programme has ended

Blockage or kink in drainage hose.

Pump is jammed.

Filters are blocked.

The programme is still running.

Wait for the programme to end

(numerical display will indicate 0).

Perform “Reset” function.

en

42

... during washing

Unusual amount of foam is created

Normal washing up liquid has

been poured into the rinse-aid

container.

Remove any spilled rinse aid with

a cloth as it could otherwise lead

to excessive foaming during the

next washing cycle.

Appliance stops suddenly while

washing is taking place

Cut in electricity supply to

appliance.

Water supply has been

interrupted.

Knocking sound can be heard

while washing is taking place

A spray arm is knocking against

the dishes inside the appliance.

Rattling sound can be heard while

washing is taking place

Crockery has not been stacked

properly inside the appliance.

Knocking sound coming from inlet

valves

This is caused by the way the

water pipes have been laid and it

has no effect upon the way the

appliance functions. There is no

remedy for this.

... with the dishes, cutlery, etc.

Remnants of food are stuck to the

dishes, cutlery, etc.

Dishwasher was not loaded

properly. Jets of water could not

reach all parts of the dishes, etc.

Too many items in the rack.

Items in the rack were touching

each other.

Not enough detergent was added

to dispenser.

Selected wash programme was

not intensive enough.

Rotation of spray arm was

obstructed by dish, etc.

Nozzles in spray arm are blocked

by remnants of food.

Filters are blocked.

Filters have been incorrectly fitted.

Waste-water pump is jammed.

Plastic items are discoloured

Not enough detergent was added

to dispenser.

White stains are left on crockery,

glasses have a milky appearance

Not enough detergent was added

to input compartment.

Amount of rinse-aid was set too

low.

Although water is quite hard, no

salt has been put in appliance.

Water softener was set too low.

Lid on salt container is not

screwed tight.

If you used a phosphate-free

detergent, try a detergent

containing phosphates and

compare results.

en

43

Dishes, cutlery, etc. have not been

dried

Selected programme did not

include drying function.

Amount of rinse-aid was set too

low.

Items were removed from

dishwasher too soon.

Glasses have a dull appearance

Amount of rinse-aid was set too

low.

Tea stains or traces of lipstick have

not been completely removed

Detergent does not have a

sufficient bleaching effect.

Washing temperature was set too

low.

Traces of rust on cutlery

Cutlery is not sufficiently rustproof.

Salt content in washing water is

too high.

Lid on salt container is not

screwed tight.

Too much salt was spilt while

filling container.

Glasses become clouded and

discoloured; coating cannot be

wiped off

Unsuitable detergent was used.

Glasses are not dishwasher-proof.

Smears left behind on glasses and

cutlery; glasses have acquired a

metallic appearance

Amount of rinse-aid set too high.

Customer Service

Please call your local service agent, if you

are not able to resolve any problem

yourself. The name of your nearest service

agent is shown in the Customer Service

address list. When you call, please provide

details of the model number (1) and the

production (FD) number (2) which are

shown on the nameplate on the appliance

door.

FD

2

1

Warning

Please note that a visit by the

customer service technician in

the event of a fault or one of

the problems previously

discussed is not free of charge

even during the warranty

period.

Page is loading ...

Bosch SGI5924/21 User manual

Bosch SGI5924/21 User manual

in other languages

Related papers

Other documents