Renkforce RF-4730925 Owner's manual

Renkforce
Brand
Renkforce
Model
RF-4730925
Category
Coffee making accessories
Type
Owner's manual
Page is loading ...
Page is loading ...
• If it is no longer possible to operate the product safely, stop using it and
prevent unauthorized use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Always handle the product carefully. Jolts, impacts or a fall even from a
low height may damage the product.
• Always observe the safety and operating instructions of any other
devices which are connected to the product.
• Never move the product with an installed hard disk drive when the latter
is in operation. Doing so may make the read/write heads on the hard disk
drive touch the magnetic disk. This may lead to data loss and damage
the hard disk drive. Turn the product off and wait at least 30 seconds
(until the magnetic disks in the hard disk drive have stopped rotating)
before you move the product.
• Do not place the product in the proximity of speakers or machines that
radiate a strong magnetic eld.
• Only touch the casing on the sides of the hard drive; do not touch the
circuit board. Electrostatic discharges may destroy your hard drive.
• When setting up the product, make sure that the cable is not pinched,
kinked or damaged by sharp edges.
• Never use the product immediately after it has been brought from a cold
room into a warm one. The condensation generated could destroy the
product. Allow the product to reach room temperature before connecting
it and putting it to use. This may take several hours.
• Use suitable padding to protect the surfaces of valuable furniture against
scratches and dents.
• Consult a technician if you are not sure how to use or connect the product.
• Maintenance, modications and repairs are to be performed exclusively
by an expert or at a qualied shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Installing a hard drive
• Loosen the two screws on the side of the housing.
• Carefully remove the cover from the housing.
• Connect a hard drive with the appropriate terminal located on the inside of the
cover. Do not use any force.
• Gently slide the hard drive into the housing.
• Attach the cover with 2 screws.
The third included screw is a spare.
Driver installation
The required drivers are already included in the operating system. A separate driver
is therefore not included with the product.
Operating instructions
2.5” Aluminium hard drive housing
RF-FG-A25S
Item no. 1576975
Intended use
The product is used for the installation of a 6.35 cm (2.5”) SATA hard drive. The
product connects to your computer via USB. The power is supplied via a USB port
as well.
This product is intended for indoor use only. Do not use it outdoors. Contact with
moisture (e.g. in bathrooms) must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product.
Using the product for purposes other than those described above may damage the
product. In addition, improper use can cause hazards such as a short circuit, re or
electric shock. Read the instructions carefully and store them in a safe place. Make
this product available to third parties only together with its operating instructions.
This product complies with statutory national and European regulations. All company
and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Hard drive housing
• USB Y cable
• Screw driver
• 3 x screws
• 4 x housing feet, self-adhesive
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or scan
the QR code on this page. Follow the instructions on the website.
Explanation of symbols
The symbol with the lightning in the triangle indicates that there is a risk to
your health, e.g. due to an electric shock.
This symbol is used to highlight important information in these operating
instructions. Always read this information carefully.
This symbol indicates special information and advice on how to use the
product.
Safety instructions
Read the operating instructions carefully and especially observe the
safety information. If you do not follow the safety instructions and
information on proper handling in this manual, we will assume no
liability for any resulting personal injury or damage to property. Such
cases will invalidate the warranty/guarantee.
• The product is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, ammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microlming, or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE. *1576975_v1_1017_02_IPL_m_en
Connection
Some notebooks supply less than 500 mA per USB port. In this case, it is
possible that the hard drive may not start or be recognised. Use a USB hub
with its own mains adapter to ensure an adequate current supply should
this be the case.
• Turn on the computer. Wait until the operating system is completely booted up.
• Connect the 2 USB plugs that are connected via the short, thin cable, with 2 free
USB ports on your computer (or with a USB hub with its own mains adapter).
• Connect the remaining USB plug with the product.
• The operating system automatically recognises the product upon rst use and
installs the necessary drivers. The drivers are already included in your operating
system.
A new hard drive has to be rstly partitioned and formatted before the drive
is displayed in Explorer and can be used; see the next section.
Partitioning/formatting the hard disk drive
• In Windows
®
, you can partition and format the hard drive via the Control Panel.
• First, make a new partition.
• Then format the newly created partition. A quick format is sufcient. Depending
on the capacity of the hard disk drive, a regular format may take a long time to
complete.
• Consult a technician if you are unsure about partitioning/formatting the hard disk
drive.
Tips and notes
a) USB 2.0
• USB 2.0 devices are backward compatible. This means that the product with the
installed hard disk also works with USB 1.1 ports. However, the transfer speed will
be reduced accordingly.
• If you are connecting the product to a USB hub, the USB hub must support the
USB 2.0 standard in order to provide the maximum transfer speed.
b) General information
• As soon as the hard drive housing is switched on, the LED lights up.
• The LED ashes during read/write access.
• Note that les may be damaged and the operating system may crash if the
connection cable is disconnected when data is being transferred. Always unmount
the hard disk drive via the operating system before disconnecting the connection
cable.
• Always handle hard disk drives carefully. Vibrations during use and even a few
seconds after the hard disk drive has turned off may make the read/write heads
touch the magnetic disk, which can destroy the hard disk drive.
• When connecting the hard disk drive for the rst time, it may take approximately
one minute for the hard disk drive to be recognised. This time may vary depending
on the operating system.
• If necessary, attach the included self-adhesive housing feet to the bottom of the
product.
Care and cleaning
• Before cleaning, unplug the product from the operating system. Wait at least
30 seconds until the magnetic plates on the hard disk drive have come to a
complete standstill. Disconnect the USB plug from the computer.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as
these may damage the casing or cause the product to malfunction.
• The product does not require maintenance except for occasional cleaning.
• Use a dry, lint-free cloth to clean the product.
Disposal
Electronic devices are recyclable waste and must not be placed in
household waste. Always dispose of the product according to the relevant
statutory regulations.
You thus full your statutory obligations and contribute to the protection of
the environment.
Technical data
Operating voltage ................... 5 V/DC (via USB)
Suitable for ............................. 6.35 cm (2.5”) SATA hard disk
Suitable hard drive height ....... max. 9.5 mm
System requirements .............. Windows
®
2000, XP (Home, Pro, with SP1, SP2,
SP3, only 32 bit), Vista™ (32/64 bit), 7 (32/64 bit),
8.0 (32/64 bit), 8.1 (32/64 bit), 10 (32/64 bit), RT
Mac OS 10.3 and above
Linux Red Hat and above
USB standard ......................... USB 2.0
Cable length ........................... 35 cm
Operating conditions ............... -10 to +50 °C, 20 – 90 % RH
Storage conditions .................. -20 to +70 °C, 20 – 90 % RH
Dimensions (L x W x H) .......... 128 x 78 x 12 mm
Weight .................................... 58 g
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Renkforce RF-4730925 Owner's manual

Renkforce
Brand
Renkforce
Model
RF-4730925
Category
Coffee making accessories
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents