Renkforce RF-4730925 Owner's manual

Brand: Renkforce

Model: RF-4730925

Category: Coffee making accessories

Type: Owner's manual

Page is loading ...

• If it is no longer possible to operate the product safely, stop using it and

prevent unauthorized use. Safe operation can no longer be guaranteed

if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Always handle the product carefully. Jolts, impacts or a fall even from a

low height may damage the product.

• Always observe the safety and operating instructions of any other

devices which are connected to the product.

• Never move the product with an installed hard disk drive when the latter

is in operation. Doing so may make the read/write heads on the hard disk

drive touch the magnetic disk. This may lead to data loss and damage

the hard disk drive. Turn the product off and wait at least 30 seconds

(until the magnetic disks in the hard disk drive have stopped rotating)

before you move the product.

• Do not place the product in the proximity of speakers or machines that

radiate a strong magnetic eld.

• Only touch the casing on the sides of the hard drive; do not touch the

circuit board. Electrostatic discharges may destroy your hard drive.

• When setting up the product, make sure that the cable is not pinched,

kinked or damaged by sharp edges.

• Never use the product immediately after it has been brought from a cold

room into a warm one. The condensation generated could destroy the

product. Allow the product to reach room temperature before connecting

it and putting it to use. This may take several hours.

• Use suitable padding to protect the surfaces of valuable furniture against

scratches and dents.

• Consult a technician if you are not sure how to use or connect the product.

• Maintenance, modications and repairs are to be performed exclusively

by an expert or at a qualied shop.

• If you have questions which remain unanswered by these operating

instructions, contact our technical support service or other technical

personnel.

Installing a hard drive

• Loosen the two screws on the side of the housing.

• Carefully remove the cover from the housing.

• Connect a hard drive with the appropriate terminal located on the inside of the

cover. Do not use any force.

• Gently slide the hard drive into the housing.

• Attach the cover with 2 screws.

The third included screw is a spare.

Driver installation

The required drivers are already included in the operating system. A separate driver

is therefore not included with the product.

Operating instructions

2.5” Aluminium hard drive housing

RF-FG-A25S

Item no. 1576975

Intended use

The product is used for the installation of a 6.35 cm (2.5”) SATA hard drive. The

product connects to your computer via USB. The power is supplied via a USB port

as well.

This product is intended for indoor use only. Do not use it outdoors. Contact with

moisture (e.g. in bathrooms) must be avoided under all circumstances.

For safety and approval purposes, you must not rebuild and/or modify this product.

Using the product for purposes other than those described above may damage the

product. In addition, improper use can cause hazards such as a short circuit, re or

electric shock. Read the instructions carefully and store them in a safe place. Make

this product available to third parties only together with its operating instructions.

This product complies with statutory national and European regulations. All company

Delivery content

• Hard drive housing

• USB Y cable

• Screw driver

• 3 x screws

• 4 x housing feet, self-adhesive

• Operating instructions

Up-to-date operating instructions

Download the latest operating instructions at www.conrad.com/downloads or scan

the QR code on this page. Follow the instructions on the website.

Explanation of symbols

The symbol with the lightning in the triangle indicates that there is a risk to

your health, e.g. due to an electric shock.

This symbol is used to highlight important information in these operating

instructions. Always read this information carefully.

This symbol indicates special information and advice on how to use the

product.

Safety instructions

Read the operating instructions carefully and especially observe the

safety information. If you do not follow the safety instructions and

information on proper handling in this manual, we will assume no

liability for any resulting personal injury or damage to property. Such

cases will invalidate the warranty/guarantee.

• The product is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. This may

become dangerous playing material for children.

• Protect the product from extreme temperatures, direct sunlight, strong

jolts, high humidity, moisture, ammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method (e.g. photocopying, microlming, or the capture in

electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.

This publication represents the technical status at the time of printing.

Connection

Some notebooks supply less than 500 mA per USB port. In this case, it is

possible that the hard drive may not start or be recognised. Use a USB hub

with its own mains adapter to ensure an adequate current supply should

this be the case.

• Turn on the computer. Wait until the operating system is completely booted up.

• Connect the 2 USB plugs that are connected via the short, thin cable, with 2 free

USB ports on your computer (or with a USB hub with its own mains adapter).

• Connect the remaining USB plug with the product.

• The operating system automatically recognises the product upon rst use and

installs the necessary drivers. The drivers are already included in your operating

system.

A new hard drive has to be rstly partitioned and formatted before the drive

is displayed in Explorer and can be used; see the next section.

Partitioning/formatting the hard disk drive

• In Windows

, you can partition and format the hard drive via the Control Panel.

• First, make a new partition.

• Then format the newly created partition. A quick format is sufcient. Depending

on the capacity of the hard disk drive, a regular format may take a long time to

complete.

• Consult a technician if you are unsure about partitioning/formatting the hard disk

drive.

Tips and notes

a) USB 2.0

• USB 2.0 devices are backward compatible. This means that the product with the

installed hard disk also works with USB 1.1 ports. However, the transfer speed will

be reduced accordingly.

• If you are connecting the product to a USB hub, the USB hub must support the

USB 2.0 standard in order to provide the maximum transfer speed.

b) General information

• As soon as the hard drive housing is switched on, the LED lights up.

• The LED ashes during read/write access.

• Note that les may be damaged and the operating system may crash if the

connection cable is disconnected when data is being transferred. Always unmount

the hard disk drive via the operating system before disconnecting the connection

cable.

• Always handle hard disk drives carefully. Vibrations during use and even a few

seconds after the hard disk drive has turned off may make the read/write heads

touch the magnetic disk, which can destroy the hard disk drive.

• When connecting the hard disk drive for the rst time, it may take approximately

one minute for the hard disk drive to be recognised. This time may vary depending

on the operating system.

• If necessary, attach the included self-adhesive housing feet to the bottom of the

product.

Care and cleaning

• Before cleaning, unplug the product from the operating system. Wait at least

30 seconds until the magnetic plates on the hard disk drive have come to a

complete standstill. Disconnect the USB plug from the computer.

• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as

these may damage the casing or cause the product to malfunction.

• The product does not require maintenance except for occasional cleaning.

• Use a dry, lint-free cloth to clean the product.

Disposal

Electronic devices are recyclable waste and must not be placed in

household waste. Always dispose of the product according to the relevant

statutory regulations.

You thus full your statutory obligations and contribute to the protection of

the environment.

Technical data

Operating voltage ................... 5 V/DC (via USB)

Suitable for ............................. 6.35 cm (2.5”) SATA hard disk

Suitable hard drive height ....... max. 9.5 mm

System requirements .............. Windows

2000, XP (Home, Pro, with SP1, SP2,

SP3, only 32 bit), Vista™ (32/64 bit), 7 (32/64 bit),

8.0 (32/64 bit), 8.1 (32/64 bit), 10 (32/64 bit), RT

Mac OS 10.3 and above

Linux Red Hat and above

USB standard ......................... USB 2.0

Cable length ........................... 35 cm

Operating conditions ............... -10 to +50 °C, 20 – 90 % RH

Storage conditions .................. -20 to +70 °C, 20 – 90 % RH

Dimensions (L x W x H) .......... 128 x 78 x 12 mm

Weight .................................... 58 g

Page is loading ...

Renkforce RF-4730925 Owner's manual

Brand: Renkforce

Model: RF-4730925

Category: Coffee making accessories

Type: Owner's manual

Download PDF

report

in other languages

français: Renkforce RF-4730925 Le manuel du propriétaire
Deutsch: Renkforce RF-4730925 Bedienungsanleitung
Nederlands: Renkforce RF-4730925 de handleiding

Renkforce RF-4730925 Owner's manual

Renkforce RF-4730925 Owner's manual

in other languages

Related papers

Other documents