Metabo BHE 2444 Operating instructions

BHE 2444
Metabo
Brand
Metabo
Model
BHE 2444
Category
Power tools
Type
Operating instructions

This manual is also suitable for

www.metabo.com
en Operating Instructions 4
fr Mode d'emploi 8
es Instrucciones de manejo 12
BHE 2444
BHE 2644
KHE 2444
KHE 2644
KHE D-26
Page is loading ...
3
Metabowerke GmbH
Postfach 1229
Metabo-Allee 1
D-72622 Nuertingen
Germany
BHE 2444 KHE 2444 BHE 2644 KHE 2644 KHE D-26
Serial Number - - 06153... 06154... 06156... 06157... 01109...
P
1
W 800 800 800 800 800
P
2
W 370 370 410 410 410
I
120 V
A 77777
n
1
/min
rpm
0 - 1230 0 - 1230 0 - 1150 0 - 1150 0 - 1150
n
2
/min
rpm
880 880 960 960 960
SDS-plus
ø max.
mm
in
24 (
15
/
16
) 24 (
15
/
16
)
26 (1) 26 (1) 26 (1)
s max.
/min
bpm
5400 5400 5400 5400 5400
W
(EPTA 05/2009)
J 2,3 2,3 2,3 2,3 2,3
ø max.
mm
in
68
(2
5
/
8
)
68
(2
5
/
8
)
68
(2
5
/
8
)
68
(2
5
/
8
)
68
(2
5
/
8
)
ø max.
mm
in
30 (1
3
/
16
) 30 (1
3
/
16
) 30 (1
3
/
16
) 30 (1
3
/
16
) 30 (1
3
/
16
)
ø max.
mm
in
13 (
1
/
2
) 13 (
1
/
2
) 13 (
1
/
2
) 13 (
1
/
2
) 13 (
1
/
2
)
m
kg
lbs
2,3 (5.1) 2,4 (5.3) 2,7 (6.0) 2,9 (6.4) 2,7 (6.0)
D
mm
in
43 (1
11
/
16
) 43 (1
11
/
16
) 43 (1
11
/
16
) 43 (1
11
/
16
) 43 (1
11
/
16
)
12.
ENGLISHen
4
Operating Instructions
In conjunction with the appropriate accessories, this
rotary hammer drill is suitable for impact drilling and
chiselling (KHE 2444, KHE 2644, KHE D-26 only)
into concrete, stone and other such materials, into
brickwork with drill bits, and non-impact drilling into
metal, wood etc. and for driving screws.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.
For your own protection and for the
protection of your electrical tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Reading the operating instruc-
tions will reduce the risk of injury.
Pass on your electrical tool only together with these
documents.
General Power Tool Safety Warnings
WARNING – Read all safety warnings and
instructions. Failure to follow the warnings
and instructions may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for future
reference! The term "power tool" in the warnings
refers to your mains-operated (corded) power tool
or battery-operated (cordless) power tool.
2.1 Work area safety
a) Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2.2 Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes, radiators,
ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
2.3 Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
2.4 Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the rate
for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
1. Specified Conditions of Use
2. General Safety Information
ENGLISH en
5
be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool's operation. If
damaged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
2.5 Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Wear ear protectors. Exposure to noise can cause
hearing loss.
Use auxiliary handle, if supplied with the tool.
Loss of control can cause personal injury.
Hold power tools by insulated gripping
surfaces, when performing an operation where
the cutting tool may contact hidden wiring or
its own cord. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power
tool „live“ and could give the operator an electric
shock.
Always hold the machine with both hands using the
handles provided, stand securely and concentrate.
Always wear protective goggles, gloves, and sturdy
shoes when working with this tool.
Ensure that the spot where you wish to work is
free of power cables, gas lines or water pipes
(e.g. using a metal detector).
Metabo S-automatic safety clutch.
When the safety clutch responds, switch off the
machine immediately! If the tool jams or catches,
the power supply to the motor is restricted. Due to
the strong force which can arise, always hold the
machine with both hands using the handles
provided, stand securely and concentrate.
Avoid inadvertent starts by always unlocking the
switch when the plug is removed from the mains
socket or in case of a power cut.
Do not touch the rotating tool!
Remove chips and similar material only with the
machine at standstill.
Caution must be exercised when driving screws into
hard materials (driving screws with metric or
imperial threads into steel)! The screw head may
break or a high reverse torque may build up on the
handle.
Pull the plug out of the plug socket before any
adjustments or servicing are performed.
Smaller workpieces must be secured such that they
are not carried along with the drill bit when drilling
(e.g. by clamping in a vice or on a work bench with
screw clamps).
Additional Warnings:
California Prop 65 08_2018
Some dust created by power
sanding, sawing, grinding,
drilling, and other construction activities
contains chemicals known to cause cancer,
birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and
other masonry products, and
• Arsenic and chromium from chemicallytreated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
SYMBOLS ON THE TOOL:
...... Class II Construction
V .......... volts
A .......... amperes
Hz ........ hertz
W ......... watts
BPM..... beat per minute
~.......... alternating current
n
0
......... no-load speed
rpm ...... revolutions per minute
.../min... revolutions per minute
See page 2.
1 Side handle
2T
ool lock
3 Depth stop
4 Scaffold hook
5 Rotation selector switch
6 Locking button for continuous activation
7 Trigger switch
8 Stop
3. Special Safety Information
4. Overview
WARNING
ENGLISHen
6
9 Control knob
Before plugging in check to see that the rated
mains voltage and mains frequency, as stated
on the rating label, match with your power supply.
Always install an RCD with a max. trip current
of 30 mA upstream.
5.1 Side handle installation
For safety reasons, always use the side
handle supplied.
Open the clamping ring by turning the side handle
(1) counter-clockwise. Place the side handle onto
the machine's collar. Insert the depth stop (3).
Tighten the side handle in the required angle
depending on the task at hand.
6.1 Scaffold hook (only KHE D-26)
The scaffold hook (4) is designed for hanging the
machine on a scaffold or ladder step. The holding
point must be suitable for keeping the machine
secure. Ensure that no damage is caused by a
falling machine. Do not load the machine with
additional weight.
Do not use the scaffold hook if it is damaged.
Unfold the scaffold hook (4) to hang it (until it locks).
Hang the machine carefully.
Attention, risk of crushing when folding! Do not
reach into the hinge area, wear safety gloves.
Always fold in the scaffold hook (4) (until it locks)
when is is not being used.
6.2 Depth Stop Setting
Loosen the side handle (1). Set depth stop (3) to the
desired drilling depth and retighten the side handle.
6.3 Setting direction of rotation
Do not activate the rotation selector switch (5)
unless the motor has completely stopped.
See page 2.
R = Clockwise setting
L = Counter-clockwise setting
6.4 Operating mode selection
Select the desired operating mode by turning the
control knob (9). To turn, push the stop (8).
Drilling
Hammer drilling
Chiselling
(KHE 2444, KHE 2644, KHE D-26 only)
In chiselling mode, the chisel is locked so that it
cannot turn.
To position the chisel for a particular application, set
the switch button (9) between and .
When a chisel is fitted, only operate the
machine in the chiselling operating mode
.
Avoid levering with the machine when a chisel
is fitted.
6.5 Tool change with SDS chuck
Before fitting, clean tool shank and apply
special grease (accessories order no.
6.31800)! Use only SDS-Plus tools.
Inserting tools:
- Turn tool and insert until it engages. The tool is
locked automatically.
Removing the tool:
See page 2, fig. A.
Pull tool lock (2) backwards in direction indicated by
arrow (a) and remove tool (b).
6.6 Switching on/off, changing speed
Switching on, speed: press the trigger (7).
The speed can be changed by pressing in the
trigger.
Release the trigger to switch off.
Continuous activation: While pressing on the
trigger (7), press in the locking button (6) and
then release the trigger. To switch off, press and
release the trigger (7) again.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand in a
safe position and concentrate.
The vent slots of the machine should be cleaned
from time to time.
If the trigger (7) can not be depressed, check to see
that the direction of rotation selector switch (5) is
fully set to the R or L position.
f
Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
Fit accessories securely. Secure the machine if it is
operated in a bracket. Loss of control can cause
personal injury.
For a complete range of accessories, see
www.metabo.com or the main catalogue.
5. Start of Operation
6. Use
7. Maintenance
8. Trouble Shooting
9. Accessories
ENGLISH en
7
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Explanatory notes on the information on page 3.
Changes due to technological progress reserved.
P
1
=rated input
P
2
=rated output
I
120 V
= Current at 120 V
n
1
=no-load speed
n
2
=load speed
ø max =max. solid drill diameter
s max =max. impact rate
W =single impact energy
m =weight
D =spindle collar diameter
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Wear ear protectors!
10. Repairs
11. Environmetal Protection
12. Technical Specifications
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Metabowerke GmbH
Metabo-Allee 1
72622 Nuertingen
Germany
www.metabo.com
170 27 4240 - 0718 CP
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Metabo BHE 2444 Operating instructions

BHE 2444
Metabo
Brand
Metabo
Model
BHE 2444
Category
Power tools
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents