Haier QDP555SYNFS User manual

Owner's Manual

Manuel d’utilisation

Manual del propietario

QDP555 Series

Built-In Dishwasher

Lave-Vaisselle Incorpere

Lavavajillas Empotrado

49-4000207 Rev 0 09-19 GEA

2 49-4000207 Rev 0

ENGLISH

RECORD KEEPING

Thank you for purchasing this Haier product. This Owner's

Manual will help you get the best performance from your new

dishwasher.

For future reference, record the model and serial number

located on the the tub wall just inside the door.

Staple your proof of purchase to this manual to aid in

obtaining warranty service if needed.

____________________________________________________

Model number

____________________________________________________

Serial number

____________________________________________________

Date of purchase

TABLE OF CONTENTS

SAFETY INFORMATION ............................................................................................3

USING THE DISHWASHER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Getting Started ........................................................................................................ 5

Dispensers ............................................................................................................ 8

Appliance Communication ............................................................................................ 10

Loading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

CARE AND CLEANING ............................................................................................18

TROUBLESHOOTING TIPS ........................................................................................20

LIMITED WARRANTY .............................................................................................23

CONSUMER SUPPORT ........................................................................................... 24

49-4000207 Rev 0 3

ENGLISH

SAFETY INFORMATION

WARNING

For your safety, the information in this manual must be followed to minimize the

risk of fire, explosion, electric shock, and to prevent property damage, personal injury, or death.

WARNING

PROPER INSTALLATION AND MAINTENANCE

This dishwasher must be properly installed and located in accordance with the Installation Instructions before it is used. If

you did not receive an Installation Instructions sheet with your dishwasher, you can receive one by visiting our Website at

haierappliances.com. In Canada, visit haiercanada.ca.

■

Connect the dishwasher/appliance to a grounded

metal, permanent wiring system; or run an equipment-

grounding conductor with the circuit conductors and

connect to the equipment-grounding terminal or lead of

the appliance.

■

Improper connection of the equipment-grounding

conductor can result in a risk of electric shock. Check

with a qualified electrician or service representative

if you are in doubt whether the appliance is properly

grounded.

■

Dispose of discarded appliances and shipping or packing

material properly.

■

Do not attempt to repair or replace any part of your

dishwasher unless it is specifically recommended in

this manual. All other servicing should be referred to a

qualified technician.

■

Use only cord kit WX09X70910 or hard-wire to building

electrical. Failure to follow this instruction, could result

in risk of fire and personal injury.

■

To minimize the possibility of electric shock, disconnect

this appliance from the power supply before attempting

any maintenance.

NOTE: Turning the dishwasher off does not disconnect

the appliance from the power supply. We recommend

having a qualified technician service your appliance.

WARNING

WHEN USING YOUR DISHWASHER, FOLLOW BASIC PRECAUTIONS,

INCLUDING THE FOLLOWING:

■

Use this appliance only for its intended purpose as

described in this Owner’s Manual.

■

Use only detergents or wetting agents recommended

for use in a dishwasher and keep them out of reach

of children. Using a detergent that is not specifically

designed for dishwashers will cause the dishwasher to

fill with suds.

■

Locate sharp items so that they are not likely to damage

the door seal.

■

Load sharp knives with the handles up to reduce the risk

of cut-type injuries.

■

Do not wash plastic items unless marked dishwasher

safe or the equivalent. For plastic items not so marked,

check the manufacturer’s recommendations.

■

Do not touch the heating element during or immediately

after use.

■

Do not operate your dishwasher unless all enclosure

panels are properly in place.

■

Do not tamper with controls.

■

Do not abuse, sit on or stand on the door or dish rack of

the dishwasher.

■

To reduce the risk of injury, do not allow children to play

with, on or inside this appliance at any time.

■

Do not store or use combustible materials including

gasoline or other flammable liquids or vapors in the

vicinity of this or any other appliance.

■

Small parts, such as rack clips and filter retaining posts,

can be a choke hazard to small children if removed from

the dishwasher. Keep out of reach of small children.

■

Detailed grounding instructions can be found in the

“PREPARE ELECTRICAL WIRING” section of the

installation Instructions.

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

4 49-4000207 Rev 0

ENGLISH

READ AND SAVE THESE INSTRUCTIONS

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

WARNING

WATER HEATER SAFETY

Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two or more weeks.

HYDROGEN GAS IS EXPLOSIVE.

If the hot water has not been used for two or more weeks, prevent the possibility of damage or injury by turning on all hot

water faucets and allowing them to run for several minutes. Do this before using any electrical appliance connected to the

hot water system. This simple procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable, do

not smoke, use an open flame, or use the appliance during this process.

TO PREVENT MINOR INJURY AND PROPERTY DAMAGE

■

During or after wash cycle, contents may be hot to the

touch. Use care before handling.

■

Close supervision is necessary if this appliance is used

by or near children. Do not allow children to play around

the dishwasher when closing the door, closing the upper

rack, or while vertically adjusting the upper rack due to

the possibility of small fingers being pinched.

■

Non-Dishware Items: Do not wash items such as

electronic air cleaner filters, furnace filters and paint

brushes in your dishwasher. Damage to the dishwasher

and discoloration or staining of the dishwasher may

result.

WARNING

RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE DISHWASHER

Junked or abandoned dishwashers are dangerous…even if they will sit for “just a few days.” If you are getting rid of your

dishwasher, please follow the instructions below to help prevent accidents.

■

Do not allow children to play with, on, or inside this or any discarded appliance.

■

Take off the door of the washing compartment.

CAUTION

ELECTRICAL REQUIREMENTS

Be sure that the electrical connection and wire size are

adequate and in conformance with the National Electric

Code, ANSI/NFPA 70 – latest edition, and all local codes

and ordinances.

This appliance must have:

■

120V, 60Hz, AC-only, 15-ampere or 20-ampere, fused

electrical supply.

■

Wiring must be 2 wire with ground and rated for 75°C (167°F).

■

If the electrical supply does not meet the above

requirements, call a licensed electrician before proceeding.

It is recommended to have:

■

A circuit breaker or time-delay fuse.

■

A properly grounded individual branch circuit.

CAUTION

NOTICE

■

If your dishwasher is connected to a wall switch, ensure

that the switch is on prior to use.

■

If you choose to turn the wall switch off between wash

cycles, allow 5-10 seconds after turning the switch on

before touching Start to allow the control to initialize.

■

Use only powder, Finish

®

Quantum

®

Automatic

Dishwashing Detergent, liquid detergents or rinse

agents recommended for use in a dishwasher and keep

them out of the reach of children. Finish

®

Quantum

®

Automatic Dishwashing Detergent, and Finish

®

Jet-

Dry

®

Rinse Aid rinse agents have been approved for use

in all Haier Appliances dishwashers.

49-4000207 Rev 0 5

ENGLISH

USING THE DISHWASHER

Features and appearance will vary throughout this manual

SELECT CYCLE

Open the door and press the Cycle pad for the desired wash cycle. The light next to the Cycle pad will be lit to indicate

which wash cycle has been selected.

NOTE: Cycle times vary based on soil level, water temperature, and options selected.

The cycle must be selected with the door in the open position. The cycle will not start until the Start pad is pushed and

the door is closed within 4 seconds.

Smart This cycle automatically senses the soil level and adjusts the wash cycle accordingly. It is meant for daily,

regular, or typical use to completely wash a full load of normally soiled dishes and is designed to conserve

both water and energy. *Time range: 1 hour 50 minutes - 2 hours 10 minutes.

Heavy This cycle is meant for heavily soiled dishes, cookware, pots, or pans with dried-on or baked-on soils.

Everyday dishes are safe to be used in this cycle. *Time: 2 hours 31 minutes.

Medium This cycle is meant for daily, regular, or typical use to completely wash a full load of normally soiled dishes

and is designed to conserve both water and energy. *Time range: 1 hour 15 minutes - 1 hour 50 minutes.

NOTE: Medium was used to rate the energy efficiency of this dishwasher.

Light This cycle is for lightly soiled dishes. It is safe for china and crystal with no options selected. *Time: 55 minutes.

Quick This cycle will quickly wash lightly soiled dishes. *Time: 60 minutes. For better drying, select Dry. This

will raise the final rinse temperature and extend the dry time. Dry will add 49 to 90 minutes to the cycle

time. When the Clean light comes on, open the door, pull the racks out, and the dishes will “flash” dry in

approximately five minutes.

*Washing time only. Does not include drying time, Auto Hot Start, or options. NOTE: If the incoming water temperature

is too low, the Auto Hot Start feature may add up to 11 minutes of additional time.

4

LOAD DISHWASHER

For best dishwashing results, follow the loading guidelines found in the Loading section. No pre-rinsing of normal food

soil is required. Scrape off hard soils, including bones, toothpicks, skins, and seeds. Remove leafy vegetables, meat

trimmings, and excessive amounts of grease or oil.

ADD DETERGENT

Add needed amount of detergent to the detergent dispenser. Use detergent such as Finish

®

Quantum

®

Automatic

Dishwashing Detergent. See Dispensers section.

ADD RINSE AGENT

Add rinse agent such as Finish

®

Jet-Dry

®

Rinse Aid to the rinse agent dispenser. See Dispensers section. NOTE: The

use of rinse aid can further enhance the dishwasher’s drying performance.

1

2

3

Top Bottom

6 49-4000207 Rev 0

ENGLISH

START DISHWASHER

Start Press the Start pad and close the door within 4 seconds to start the cycle or begin the Delay

countdown. The wash cycle will begin shortly after closing the door. The display will turn off if the door

remains open for two minutes. To activate the display, close and open the door or press any pad.

Interrupt

or Pause

To interrupt or pause a cycle, slowly open the door. Opening the door will cause the wash cycle to

pause. The dishwasher will beep every minute to remind you to close the door. To restart or resume the

cycle, press Start, and close the door within 4 seconds.

Cancel To cancel a wash cycle, press and hold the Start pad for 3 seconds and close door.

The dishwasher will drain, emit a beep sound, and the wash cycle light will turn off.

Cycle Status The indicator light on the door front will change color to indicate the wash status. During the wash

cycle, the indicator light will be blue. When the wash cycle is complete, the light will change to white.

6

USING THE DISHWASHER

5

SELECT OPTIONS

The light by the selected pad will be lit to indicate which Option has been selected.

Light Press to turn the tub light on or off.

Delay Delays the start of a wash cycle up to 8 to 12 hours depending on model. Press Delay, to select the

number of hours, then press Start one time and close door to begin countdown. The cycle will start

once allotted time has expired.

Sanitize This option raises the water temperature in the final rinse to sanitize your dishware but may increase

cycle time by 60 minutes. The cycle length will vary depending on the temperature of your inlet water.

NOTE: This option is monitored for sanitization requirements. If the cycle is interrupted during or

after the main wash portion or if the incoming water temperature is so low that adequate water

heating cannot be achieved, the sanitizing conditions may not be met. In these cases, the Sanitized

light will not illuminate at the end of the cycle. Utilizing this option will modify the cycle to meet the

requirements of Section 6, NSF 184 for soil removal and sanitization efficacy.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

Zones Selecting either the Top or Bottom Zones will target dishwashing of just one rack. This will shorten the

cycle time and conserve energy. This option should be used when dishes are placed in only one rack.

Temp This option increases the temperature to help clean heavily soiled dishes and will increase the cycle

time by 20 to 50 minutes. Option may be turned On or Off during the wash cycle. This option will also

improve dry performance on the Medium cycle.

Dry Off Shuts off the drying option. Dishes air dry naturally and energy is saved. Open the dishwasher door to

speed drying.

Dry Normal Turns on the option for faster drying. This option may add up to 64 minutes to the cycle time. On

models with the hidden heater feature, this option boosts the temperature of the dishwasher during

the final rinse portion of the cycle then utilizes a fan to circulate air to dry the dishes. This very efficient

fan may run for an additional 90 minutes after the cycle is complete to maximize drying performance.

Fan operation will end if the door is opened during this 90 minute period.

Dry Extra This option can be selected by pressing the Dry pad twice to illuminate the Extra light. It will add

additional time to your drying option, further enhancing the dishwasher’s performance for difficult to

dry items.

49-4000207 Rev 0 7

ENGLISH

USING THE DISHWASHER

INDICATOR LIGHTS

Sanitized Displayed at end of the cycle when Sanitize has been selected and dishwasher has met requirements for

sanitization. See Sanitize, for complete description. Closing door or pressing any pad will turn off light.

Clean Displayed when a wash cycle is complete. The light stays on as a reminder that the dishes are clean.

Opening the door will turn the light off.

DISPLAY

Time

Remaining

During operation, the display shows the total number of minutes remaining in the cycle. During a delay

start, the display will show hours of time remaining until the cycle starts.

7

8

SOUNDS

The dishwasher will emit a sound to indicate cycle

completion, pad presses, and door ajar.

MUTE

To turn the dishwasher control sounds ON/OFF, press the

Dry pad 7 times within 5 seconds.

SABBATH/DOOR WAKE UP MODE

To turn this option ON/OFF, press and hold the Start and

Temp pads for 5 seconds, close the door and wait 3 minutes

for the dishwasher to go into sleep mode. In the OFF mode,

the control display, control sounds, and interior lights will

not respond to the door opening/closing. This mode can be

used when observing certain religious holidays such as the

Sabbath. To activate the control and interior lights, press any

pad.

8 49-4000207 Rev 0

ENGLISH

USING THE DISHWASHER

CHECK THE WATER TEMPERATURE

The entering water should be at least 120°F (49°C) and not

more than 150°F (66°C) for effective cleaning and to prevent

dish damage. Check the water temperature with a candy or

meat thermometer.

Turn on the hot water faucet nearest the dishwasher, place the

thermometer in a glass and let the water run continuously into

the glass until the temperature stops rising.

USE A RINSE AGENT

Rinse agents, such as Finish

®

Jet-Dry

®

Rinse Aid are designed for great drying action and to protect against spots and film

build-up on your dishes, glasses, flatware, cookware, and plastic.

Filling the Rinse Agent Dispenser

The rinse agent dispenser holds 3.5 oz. (104 ml) of rinse agent. Under normal conditions, this will last approximately one

month.

1

Make sure the dishwasher door is fully open.

2

Open the rinse agent dispenser door.

3

Slowly add rinse agent until the cup is full. You may need to pause several times to allow rinse

aid to settle. NOTE: Indicator window does not light up.

4

Clean up any spilled rinse agent with a damp cloth to prevent foam from forming inside the

dishwasher.

5

Close the rinse agent dispenser door.

Rinse Aid Setting

The amount of rinse agent released into the final wash can be adjusted. If water drops or hard

water spots remain on dishes after the dry cycle, increase the setting.

To adjust the setting

Open the Rinse Agent dispenser door;

then turn the adjuster clockwise to

increase the amount of rinse agent,

counterclockwise to reduce the amount

of rinse agent.

Rinse

agent

adjuster

Clockwise to reduce

water drops and

hard water spots

Counterclockwise

to reduce foaming

Indicator

window

49-4000207 Rev 0 9

ENGLISH

USING THE DISHWASHER

DETERGENT DISPENSER

The detergent dispenser is located in the center of the

dishwasher door. It has two compartments. The main wash

compartment is found inside the detergent dispenser. To open,

press the button on the side of the dispenser. The pre-wash

compartment is on the lid of the detergent dispenser. Use the

pre-wash compartment only when your water is extremely

hard or when you have a heavy soiled load. The pre-wash

compartment is not used when tablet or packet detergents are

used.

NOTE: Do not load large items in the lower rack where they may

block the wash jets from rinsing out the detergent dispenser.

You may use tablet, packet, powder, liquid or gel automatic

dishwasher detergent. Make sure you use only detergents

specifically labeled for use in automatic dishwashers. Never use

liquid hand dish detergent in an automatic dishwasher. Sudsing

and poor wash performance will result with the use of improper

detergents.

Detergents should be stored in a dry location and in their

original container to prevent loss of effectiveness. Place

detergent in the cup just prior to starting the dishwasher and

then close the cover. The cover will open during the wash

cycle.

FILLING THE DETERGENT

DISPENSER

We recommend using detergent in tablet or packet form.

Independent testing has shown this form of detergent is very

effective in the dishwasher. Finish

®

Quantum

®

Powerball

®

is an example of this type of detergent. Simply put a tablet

or packet into the main wash compartment and close the

detergent cup cover. Please notice that the tablet or packet

must be placed in the main wash compartment of the

detergent cup. If the tablet or packet is placed in the prewash

compartment or tossed in the bottom of the dishwasher,

the detergent will be flushed down the drain in a very short

period of time and will thus be wasted. Wash performance will

be very poor as a result.

If you choose to use detergent in powder, liquid or gel form,

the amount of detergent you use will be determined by the

hardness of your water, the temperature of your water, and

the food soil load inside the dishwasher. Contact your water

company to get information about the hardness of the water

in your area. Water hardness is measured in grains per gallon.

Use this information and the table above to determine the

amount of detergent to use.

You may purchase a hard water test strip from Haier

Appliances. You can order through Haier Appliances Parts by

visiting haierappliances.com/parts.

In Canada, haiercanada.ca/parts.

Use the table as a starting point and then adjust the amount

of detergent you use. Use just enough to get good wash

performance. Using just the right amount of detergent will

provide great wash performance without wasting detergent

or etching glassware.

Using too much detergent with very soft and/or very

hot water may cause a condition called etching on your

glassware. Etching is a permanent cloudiness in your

glassware. This condition is irreversible. However, using too

little detergent will cause poor wash performance.

DO NOT USE HAND DISH DETERGENT

NOTE: Using a detergent that is not specifically designed for

dishwashers will cause the dishwasher to fill with suds. During

operation, these suds will spill out of the dishwasher vents,

covering the kitchen floor and making the floor wet.

Because so many detergent containers look alike, store the

dishwasher detergent in a separate space from all other

cleaners. Show anyone who may use the dishwasher the

correct detergent and where it is stored.

While there will be no lasting damage to the dishwasher, your

dishes will not get clean using a dishwashing detergent that is

not formulated for automatic dishwashers.

Number of

Grains/Gal.

Detergent Cup(s) to Fill

Less than 4 Fill cup to 1/3 full

4 to 8 Fill cup to 2/3 full

8 to 12

Fill cup completely full

Greater than 12

Fill both main wash cup and pre

wash cup

Detergent

Dispenser

Pre-Wash

Main

Wash

Rinse Agent

Push/Slide

to Close

10 49-4000207 Rev 0

ENGLISH

APPLIANCE COMMUNICATION

WiFi Connect (for customers in the United States)

Your dishwasher is HaierAppliances WiFi Connect capable.

A WiFi communciation card is built into the product allowing

it to communicate with your smartphone for remote

monitoring, control and notifications.

Please visit www.GEAppliances.com/connect to connect

your appliance, learn more about connected appliance

features and learn what connected appliance app’s will work

with your smartphone.

WiFi Connectivity: For assistance with the appliance or

the ConnectPlus network connectivity, please call Haier

Appliances at 800-GE-CARES.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation. This equipment

has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

Labelling: Changes or modifications to this unit not expressly approved by the manufacturer could void the user’s authority to

operate the equipment.

Page is loading ...

12 49-4000207 Rev 0

ENGLISH

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware baskets

may vary from your model.

UPPER RACK

The upper rack is primarily for glasses, cups, and saucers. For

best wash performance, tilt cup and glass openings toward

the center of the rack. Other items such as pots, pans, and

plates may be placed in the upper rack. This is also a secure

place for dishwasher-safe plastic items. The upper rack can

be used for odd sized utensils. Sauce pans, mixing bowls,

and other similarly shaped items should be placed face down

for best wash performance. Ensure small plastic items are

secure so that they cannot fall on the heater at the bottom of

the dishwasher, potentially damaging the item. Some models

are equipped with a hidden heater, so dishwasher safe plastic

items can be placed in the lower rack.

IMPORTANT: Ensure that

items do not protrude

through the bottom of the

rack or silverware basket

where they will block the

rotation of the middle spray

arm. This could result in

noise during operation and/

or poor wash performance.

USING THE DISHWASHER

BOTTLE JETS

The Bottle Jets system is the ideal location to position

baby bottles, tall sports bottles, or other tall items with

narrow openings. The Bottle Jets clips hold bottles with

small openings in place so water jets are directed inside the

bottles to clean hard to reach areas. Clips can be installed or

removed by simply

slipping the clip

opening over the

top of the nozzle.

Sports bottle held in place

over a Bottle Jets clip

Baby bottle held in place

under a Bottle Jets clip

Clip

Nozzle

Bottle Jets

The upper rack may be adjusted to accommodate larger

items. To adjust the upper rack, fully extend the upper rack

and lift the front of the rack so that the rack roller wheels

clear the end hooks on the front of the rails. Continue to pull

the rack until the remaining rack roller wheels clear the end

hook. Select the set of rollers on the side of the rack that

provides the desired height, and reinstall the upper rack by

aligning the rack roller wheels on the end hook and rack rails –

Ensure that there are roller wheels above and below the rack

rails. Failure to properly align the wheels onto the end hook

and rails may result in the rack falling from the dishwasher.

Rail

End

Hook

Rack Rollers

Rail

End

Hook

Pull rack out,

lift up and over

rail end hooks,

and pull out to

remove

Upper

Rack

To add flexibility in loading, the stem safe shelf may be placed

in the up or down position or unfolded and placed in the lower

unfolded position.

The shelf may also be used to secure stemware such as wine

glasses. Because these stemware items come in various

sizes, slowly push the rack in to ensure the items do not

bump into the edges of the dishwasher, which may cause

damage to the items.

Place the

slots in the

utility shelf

clips over the

vertical

rack

wires and

push down to

attach

utility

shelf onto

second wire of

rack

UPPER RACK - ADJUSTMENT

A loaded upper rack may be heavier

than anticipated. To prevent minor

injury or damage to the contents, do not raise or lower the

upper rack after the rack is loaded.

CAUTION

49-4000207 Rev 0 13

ENGLISH

USING THE DISHWASHER

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware baskets

may vary from your model.

8 Place Settings - Upper Rack

UPPER RACK – LOADING

10 Place Settings - Upper Rack

12 Place Settings - Upper Rack

14 49-4000207 Rev 0

ENGLISH

USING THE DISHWASHER

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware baskets

may vary from your model.

LOWER RACK

The lower rack is best used for plates, saucers and cookware

items. Large items, such as broiler pans and baking racks should

be placed along the sides of the rack. If necessary, oversized

glasses and mugs can be placed in the lower rack to maximize

loading flexibility. Plates, saucers and similar items should be

placed between the tines in the direction that allows the item to

remain secure in the rack.

NOTE: Do not load large items in the lower rack where they may

block the wash jets from rinsing out the detergent dispenser.

The lower rack fold down tines can be adjusted to different

upright angles or placed flat to provide flexibility for hard-to-fit or

extra-large items.

To change the direction of the fold down tines, lower the

tines, then pull away from the bar clips that secure the

tines to the rack and remove. Reverse the direction of the

tines, orienting the handle on the opposite side of the rack.

Reattach the tines to the bar clips by pushing the tines

back until they click in place. The indexer will also need

to be switched to the opposite side of the dishwasher. To

remove the indexer, simply slide it the in the direction labeled

“unlock.” Then, align the indexer with the rack on the other

side and slide in the direction that says “lock” in order to

reattach the indexer to the rack.

IMPORTANT: It is important to ensure that items do not

protrude through the bottom of the rack or the silverware

basket where they will block the rotation of the lower spray

arm. Also, ensure that large plates, pots, or tall items don’t

hit the mid spray arm. This could result in noise during

operation and/or poor wash performance.

3 Angled

Positions

Available

or Folded

Down

Indexer

To lock, slide right.

To unlock, slide left.

Bar Clip

The clips can be a choke hazard for

small children if removed from the

dishwasher. Keep out of reach of children.

WARNING

49-4000207 Rev 0 15

ENGLISH

USING THE DISHWASHER

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware baskets

may vary from your model.

LOWER RACK – LOADING

8 Place Settings - Lower Rack

10 Place Settings - Lower Rack

12 Place Settings - Lower Rack

16 49-4000207 Rev 0

ENGLISH

USING THE DISHWASHER

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware baskets

may vary from your model.

SILVERWARE BASKET

Place flatware in the removable silverware baskets. Sharp

objects, such as forks and knives, may be placed with the handles

facing up, in order to protect your hands. For the best wash

performance, place other items such as spoons with the handles

facing down. Avoid allowing items to nest together, which may

keep them from being properly washed. When loading, distribute

items evenly in the basket.

The silverware baskets may also be used for small items, such as

measuring spoons, baby bottle nipples, plastic lids, or corn cob

holders. The silverware basket covers can be closed to contain

small items.

IMPORTANT: Do not load large or tall

utensils where they may block the detergent

dispenser, mid spray arm, or become trapped

between the door and the gasket when the

door is closed.

LOADING

Silverware Basket - 12 Place Settings

Silverware Basket - 8 Place Settings

Silverware Basket - 10 Place Settings

Page is loading ...

18 49-4000207 Rev 0

ENGLISH

CARE AND CLEANING

CONTROL PANEL

To clean the control panel, use a lightly dampened cloth.

Then dry thoroughly.

EXTERIOR DOOR PANEL

Before cleaning the front panel, make sure you know what type of

panel you have. Refer to the last two letters of your model number.

You can locate your model number on the left-hand tub wall just

inside the door. If your model number ends with BB, CC, DS, D1, ES,

FS, SA, TS, WW or W2 then you have a painted door panel. If your

model number ends with SS or S1, then you have a Stainless Steel

door panel. If your model number ends with II, then you have an

Integrated door panel.

Follow the instructions below for cleaning the door panel for

your specific model.

Painted Door Panel (model numbers ending in BB

or D1-black, CC-bisque, DS-black slate, ES-slate,

FS-fingerprint resistant, SA-silver, TS-black stainless

steel, or WW or W2-white)

Use a clean, soft, lightly dampened cloth, then dry thoroughly

.

Stainless Steel Door Panel (model numbers ending in SS or S1)

For cleaning rust and tarnish, cleaners with oxalic acid such

as Bar Keepers Friend Soft Cleanser™ will remove rust,

tarnish and small blemishes. Use only a liquid cleanser free

of grit and rub in the direction of the brush lines with a damp

soft sponge. Do not use appliance wax or polish on the

stainless steel.

For other blemishes and marks, use Stainless Steel Magic or

a similar product using a clean soft cloth. Do not use appliance

wax, polish, bleach or products containing chlorine on Stainless

Steel. You can order Stainless Steel Magic # WX10X29 through

Haier Appliances Parts by visiting haierappliances.com/parts.

In Canada, haiercanada.ca/parts.

Integrated Door Panel (model numbers ending in II)

This is a custom installed door panel, and you will need to

refer to the cabinet manufacturers recommendations for

proper cleaning.

DISHWASHER INTERIOR

To clean and de-odorize your dishwasher, use citric acid or

Finish

®

Dishwasher Cleaner, a detergent additive. Finish

®

Dishwasher Cleaner will break up mineral deposits, and

remove hard water film and stains.

You can order citric acid Haier Appliances kit #WD35X151

through Haier Appliances Parts by visiting haierappliances.

com/parts. In Canada, haiercanada.ca/parts. You can

purchase Finish

®

Dishwasher Cleaner at your local grocery

store.

STAINLESS STEEL INNER DOOR

AND TUB

The stainless steel used to make the dishwasher tub and

inner door provides the highest reliability available in a Haier

Appliances dishwasher.

If the dishwasher tub or inner door should be scratched

or dented during normal use, they will not rust or corrode.

These surface blemishes will not affect their function or

durability.

49-4000207 Rev 0 19

ENGLISH

CARE AND CLEANING

FILTER ASSEMBLY

Inspect and clean the filters periodically. This should be

done every month or more depending on usage. If there is

a decrease in wash performance or dishes feel gritty, this is

also an indication the filters need to be cleaned.

ULTRA-FINE FILTER

To clean the Ultra-Fine Filter, remove the bottom rack. Twist

the Ultra-Fine Filter counterclockwise and lift to remove.

Rinse filter with warm soapy water and use a sponge to

carefully remove any stubborn particles. Scrubbing with

scouring pads or brushes can dama ge the filter. Once

cleaned, replace the Ultra-Fine Filter, and twist it clockwise to

lock in place.

FINE FILTER

To clean the Fine Filter (mesh plate), remove the bottom rack.

Remove the Ultra-Fine Filter.

Lift the Fine Filter up and out from under the two rear

retaining tabs. Rinse filter with warm soapy water. Scouring

pads or brushes can scratch the filter surface but a soft

brush or sponge may be needed to remove stubborn soils

or calcium deposits caused by hard water. Once cleaned,

replace the Fine Filter making sure it goes under the two rear

retaining tabs. Replace the Ultra-Fine Filter.

PROTECT AGAINST FREEZING

If your dishwasher is left in an unheated place during the winter,

ask a service technician to:

1

Turn off electrical power to the dishwasher. Remove fuses or

trip circuit breaker.

2

Turn off the water supply and disconnect the water inlet line

from the water valve.

3

Drain water from the water inlet line and water valve. (Use a

pan to catch the water.)

4

Reconnect the water inlet line to the water valve.

DOES YOUR DISHWASHER HAVE AN

AIR GAP?

An air gap protects your dishwasher against water backing

up into it if a drain clogs. The air gap is not a part of the

dishwasher. It is not covered by your warranty. Not all plumbing

codes require air gaps, so you may not have one.

The air gap is easy to clean:

1

Turn off the dishwasher and lift off the air gap cover.

2

Remove the plastic cap under the cover and clean with a

toothpick.

3

Replace the cap and cover when the air gap is clean.

If the dishwasher tub or inner door should be scratched or

dented during normal use, they will not rust or corrode.

These surface blemishes will not affect their function or

durability.

Check the air gap any time your dishwasher isn’t draining well.

Air gap

Fine

Filter

Spray

Arm

Ultra-Fine

Filter

20 49-4000207 Rev 0

ENGLISH

TROUBLESHOOTING TIPS

Problem Possible Cause What To Do

Start status indicator

light flashing

The door was opened or the

cycle was interrupted.

Press the Start pad once and close the door within 4 seconds

to start the dishwasher. Press the Start pad a second time

when the dishwasher is running only if you wish to cancel the

cycle.

Dishwasher BEEPS

once every minute

This is a reminder that your

dishwasher door has been left

open during operation. It will

continue beeping until you

press Start and close the door.

Press Start and close the door.

Beeping at the end of

the cycle

This is normal. Dishwasher

will beep at end of cycle.

To turn off the double beep indicator (or re-activate it if it was

previously turned off), press the Dry pad 5 times within 3

seconds. A triple beep will sound to indicate the end-of-cycle

beep option has been turned on or off.

Dishes and flatware

not clean

Filter assembly is clogged See the CARE AND CLEANING section.

Low inlet water temperature Make sure inlet water temperature is correct (see the USING

THE DISHWASHER section). Turn on the hot water faucet

nearest the dishwasher, let run until the water temperature stops

rising. Then start the dishwasher and turn off the faucet. This

ensures the entering water is hot. Select Temp.

Water pressure is temporarily

low

Turn on a faucet. Is water coming out more slowly than usual? If so,

wait until pressure is normal before using your dishwasher.

Normal

water pressure to the dishwasher should be 20-120 psi.

Air gap or disposer clogged Clean the air gap or flush the disposer.

High drain loop or air gap not

installed

Refer to the Installation Instructions for proper drain line

installation.

Improper rack loading Make sure large dishware or utensils do not block the detergent

dispenser or the wash arms. See the LOADING section.

Poor performing detergent Use a highly rated detergent such as Finish

®

Quantum

®

Automatic Dishwashing Detergent.

Spots and filming on

glasses and flatware

Extremely hard water Use rinse agents such as Finish

®

Jet-Dry

®

Rinse Aid to prevent

spots and prevent new film build-up.

If water is extremely hard, a softener may be required.

Low inlet water temperature Make sure inlet water temperature is at least 120°F (49°C).

Overloading or improper

loading of the dishwasher

Load dishwasher as shown in the LOADING section.

Old or damp powder

detergent

Make sure detergent is fresh. Use a highly rated detergent such

as Finish

®

Quantum

®

Automatic Dishwashing Detergent.

Rinse agent dispenser empty

Refill with rinse agent such as Finish

®

Jet-Dry

®

Rinse Aid.

Too little or low performing

detergent

Make sure you use the proper amount of highly rated

detergent.

Cloudiness on

glassware

Combination of soft water

and too much detergent

This is called etching and is permanent. To prevent this from

happening, use less detergent if you have soft water. Wash

glassware in the shortest cycle that will get it clean.

Low performing phosphate-

free detergent

See A white film on glassware, dishware and the interior in

this TROUBLESHOOTING TIPS section.

Water temperature entering

the dishwasher exceeds 150°F

(66°C)

This could be etching. Lower the water heater temperature.

Suds in the tub Wrong detergent Use only automatic dishwasher detergents to avoid sudsing.

Finish

®

Quantum

®

Automatic Dishwashing Detergent has

been approved

for use in all Haier Appliances dishwashers.

Rinse agent was spilled Always wipe up rinse agent spills immediately.

49-4000207 Rev 0 21

ENGLISH

TROUBLESHOOTING TIPS

Problem Possible Cause What To Do

Detergent left in

dispenser cups

Dishes or utensils are

blocking the detergent cup

Reposition the dishes, so the water from the lower spray arm

can flush the detergent cup. See the LOADING section.

Reposition the tall utensils or heavy silverware that may

be keeping the dispenser cup door from opening. See the

LOADING section.

Don’t place large bowls or pots directly under the detergent

dispenser.

Black or gray marks

on dishes

Aluminum utensils have

rubbed against dishes

Remove marks with a mild, abrasive cleaner.

Dishes don’t dry Low inlet water temperature Make sure inlet water temperature is at least 120°F.

Select Dry.

Use Temp.

Select a higher cycle, such as Sanitize.

Rinse agent dispenser is

empty

Check the rinse agent dispenser and fill as required.

Additional drying time is

needed

Leave door closed after the Clean light appears to allow the fan

to run an additional 90 minutes.

Note: If you open the door, this fan extension will be cancelled.

Control panel

responded to inputs

but dishwasher never

filled with water

Door may not be completely

closed

Make sure the door is firmly closed.

Water valve may be turned off Make sure water valve (usually located under the sink) is turned

on.

Flood float may be stuck Remove Ultra-Fine filter and lightly tap the piece under the

ultra fine filter that looks like a salt shaker. Replace the filter.

Stained tub interior White film on inside surface—

hard water minerals

Haier Appliances recommends Finish® Jet-Dry® Rinse Aid to help

prevent hard water mineral deposits from forming.

Run dishwasher with citric acid to remove mineral deposits. Citric acid

(Part number: WD35X151) can be ordered through Haier Appliances

Parts. See back cover for ordering information. Alternatively,

purchase Finish® Dishwasher Cleaner and follow the directions on

the label.

Dishwasher won’t run Fuse is blown or circuit

breaker is tripped

Replace fuse or reset circuit breaker. Remove any other

appliances from the circuit.

Power is turned off In some installations, the power to the dishwasher is provided

through a wall switch, often located next to the disposer

switch. Make sure it is on.

Control panel is locked Unlock control panel. See the Getting started section.

Proper Start sequence was

not followed

See the Using the dishwasher section.

Control panel lights

go off when you’re

setting controls

Time too long between

touching of selected pads

Each pad must be touched within 30 seconds of the others. To

relight, touch any pad again or open the door and unlock.

Water standing in the

bottom of the tub

Air gap is clogged Clean the air gap. See the CARE AND CLEANING section.

High drain loop or air gap not

installed

Refer to the Installation Instructions for proper drain line

installation.

Water won’t pump

out of the tub

Drain is clogged If you have an air gap, clean it. See the CARE AND CLEANING

section.

If the dishwasher drains into a disposer, run disposer clear.

Check to see if your kitchen sink is draining well. If not, you may

need a plumber.

22 49-4000207 Rev 0

ENGLISH

TROUBLESHOOTING TIPS

Problem Possible Cause What To Do

Steam This is normal Warm, moist air comes through the vent during drying and

when water is being pumped out. This is necessary for drying.

Sanitized light does

not illuminate at the

end of the cycle

The door was opened and the

cycle was interrupted during

final rinse

Do not interrupt the cycle by opening the door during the wash

cycle.

The incoming water

temperature was too low

Raise the water heater temperature to between 120°F and

150°F.

Noise Normal operating sounds:

Beeping at the end of the cycle

Detergent cup opening

Water entering dishwasher

Motor stops and starts at

various times during cycle

Spray arms start and stop at

various times

Drain pump sounds during

pump out

Drain pump starts and stops

several times during each drain

These are all normal. No action is required.

Rattling dishes when the

spray arm rotates

Make sure dishes are properly loaded. See the LOADING

section.

Rattling silverware against

door during wash

Tall utensils may be placed in the upper rack to avoid bumping

against inner door during wash cycle.

A white film on

glassware, dishware

and the interior

This problem is likely caused

by a low quality phosphate-

free dishwasher detergent

To remove the white film, run your dishes through a dishwasher

cycle with citric acid. Use a WD35X151 citric acid kit found

online. Otherwise, use Finish

®

Dishwasher Cleaner found at

your local grocery store.

Pour the citric acid in the detergent cup and close the cover.

Place the filmed but otherwise clean glassware and dishware in

the dishwasher. Leave silverware and other metal items out of

the dishwasher. Turn the dishwasher on and let it run through a

complete cycle without detergent. The glassware, dishware, and

dishwasher should come out film free. Alternatively, a vinegar rinse

may be used. Pour 1 cup of vinegar into dishwasher just after the

detergent cup opens and let the dishwasher complete its cycle.

This may be repeated several times a year as needed.

The use of a rinse agent such as Finish

®

Jet-Dry

®

Rinse Aid

may help minimize a repeat build up of film. Also, the use of a

highly rated detergent such as Finish

®

Quantum

®

Automatic

Dishwashing Detergent will help prevent film build-up.

Feel air on your

legs when standing

in front of the

dishwasher in cycle

This is normal. Do not interrupt the cycle. No action is required

1

Open the door to interrupt the cycle. Pull the door handle

to release the door.

2

Do not open the door all the way until the water spray

action stops. Steam may rise out of the dishwasher.

3

Add additional items.

4

Press Start and close the door within 4 seconds to

resume the cycle.

FORGET TO ADD A DISH?

Additional items may be added to the dishwasher at any time, ideally items would be added shortly after starting a wash cycle.

Page is loading ...

Haier QDP555SYNFS User manual

This manual is also suitable for

Haier QDP555SYNFS User manual

in other languages

Related papers

Other documents