Gamber-Johnson 2020+ Ford Police Interceptor Utility Low-Profile Console Box with Cup Holder, Armrest, and TS5 Motion Attachment Kit Installation guide

Type
Installation guide
INST-947
B
TOP PLATE
WIRE CHASE
RELOCATION
PLATE
7160-1335
7160-1446 -
CONSOLE BOX 2020+ FORD PI UTILITY
LOW PROFILE
7160-1335 -
CONSOLE BOX 2020+ FORD PI UTILITY
SHORTY BOX
Printing Spec:
PS-001
© Copyright 2019 Gamber-Johnson, LLC
1/4
7160-1446
OEM PARKING
BRAKE KNOCKOUT
OEM RELOCATION
12V & USB
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Form
Revision
Product
INSTALLATION INSTRUCTIONS
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brake lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
1. Remove the OEM Center console
by loosen the 4 nuts using 10MM
socket.(shown in figure 1)
2. Remove the OEM center trim by
loosen the 2 bolts holding it using
7MM socket. Remove the OEM
12v/USB/E-brake from the Trim, (to
remove the E-brake use T20
socket.)
Installation:
Figure 1
Figure 2
3. With the OEM controller removed reinstall the trim back in place.
run the wires through the opennings
2/4
INSTALL BRAKE SWITCH
WITH #8-32 X .375" ON TOP
AND #8-32 X 1.25" ON THE BOTTOM
OEM USB/12V KNOCKOUT
4. Now place the GJ 2020+ Utility console box in place, align the
mounting holes with the OEM studs as shown in Figure 4. and hand
tighten the OEM nuts.
Installation (continued):
5. With everything in place, tighten down all bolts and nuts and check to make sure
everything is secure.
* Console 7160-1335 install using the same mounting points
*The Top Plate and Center Brace on both console boxes are designed to be removable to
aid in installation and cable routing. If either item is removed Gamber-Johnson
recommends reinstalling the screws with a drop of Blue 242 Loctite to prevent loosening.
Torque the (4) top plate bolts to 65-80 in-lbs when reinstalling.
Relocation
The parking brake can be relocated to the driver side console the the knockout provided
1.
The OEM USB/12V can be relocated to the passagner side if provided face panel is not
2.
desired
3/4
Rear Wire cover
*Supplied with
console.
7160-1446
7160-1335
WIRE CHASE KIT
7160-1484
*NOT SUPPLIED WITH
CONSOLE
Optional Equipment
*If provided side relocation is not desirable a faceplate relocation is available
GJ Part Number 7160-1459
Rear Wire Cover
With the 2020+ FORD PI Utility console GJ provides a rear wire cover for
car package with OEM option. if needed the cover can be installed with
provided 1/4-20 hardware.
4/4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Gamber-Johnson 2020+ Ford Police Interceptor Utility Low-Profile Console Box with Cup Holder, Armrest, and TS5 Motion Attachment Kit Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI