2. CIE-Group
  3. AVID3ACBT

CIE-Group AVID3ACBT Installation guide

  • Hello! I've reviewed the provided Installation Guide for the AVID3ACBT amplifier. This document details the product's features, such as Bluetooth connectivity and IR remote control functionality. It also covers installation instructions, input options, and adjustements for volume, bass, treble, and balance. I'm ready to assist you with any questions you might have about the amplifier.
  • What adjustments can be made using the IR Remote Control?
    What does the LED display show?
    What input options are available?
IR Remote Control Function:
Using the supplied IR Remote Control will give access to further features and functions of the AVID3ACBT
and will allow adjustments to the sound levels and tone settings.
The LED display panel will show the settings as any adjustments are made as follows:
• Theoverallvolumelevel(0lowest~20highest)
• Bass(L.1lowest~L.9highest)
• Treble(H.1lowest~H.9highest)
• Balance(B.1FullyLe~B.5Centre~B.9FullyRight)
Aeranychangeshavebeenmadetotheabove,theLEDdisplaywillreverttothesetvolumelevel.
PleaseensurethattheenclosedUserInstructionsarelewiththeAVID3ACBTunit,easilyavailabletothe
end user.
Bass Level
Control
Treble Level
Control
Volume Level
Control
Power
ON/OFF
L/R Speaker
Balance
Function not enabled
on AVID3BT Model
Before installation please take the time to read and understand the enclosed information.
What’s included in the box?
1xAVID3ACBTAmplifier
1xIRRemoteControlUnit&WallBracket
1x2-GangEORecessedBackbox
Specifications:
Output Power 2 x 15W @ 4W
Line Inputs Stereo 3.5mm Jack (Front panel)
2x Screw Terminal (Rear PCB)
Line Output Fixed level (Unbalanced) 1v 47kW
Bluetooth Wireless Bluetooth Receiver (secure Pairing Code)
Frequency Response 40Hz ~ 20KHz
Input Sensitivity (Lo) 200mv / (Hi) 1v
Power Requirements 230v AC
Dimensions 165(W) x 100(H) x 35(D) mm
Weight 0.26kg
InstallationGuide
Registered in England No. 2761780
CIE-Group Ltd3WiddowsonCloseBlenheimIndEstBulwellNottinghamNG68WBUK
T: +44(0)115 9770075F:+44(0)115 9770081 E: [email protected]W:www.cie-group.com
01/18
www.cie-group.com
Loudspeaker
Balance
Trim Pots
Line Output
Wired Input/AUX1
Wired
Input/
AUX2
Mono / Stereo
Jumper Selector
Loudspeaker
Outputs
AC MAINS
Input
Rear Panel Controls and Connectivity:
ScrewterminalconnectionsforACPower,AUXWiredInputs,LoudspeakerOutputsandLineLeveloutputs
are located on the rear PCB of the AVID3ACBT.
TheAVID3ACBTispoweredviaafused230vACoutlet.
Thetwo wiredAUXinput terminalsontherearare configuredforaStereoInputSignal;the three-way
connectorhasterminalsforL(LeSignal),G(Screen)andR(RightSignal).
Important Information:
It is important to note that if using the audio input located on the rear of the AVID3ACBT that the signal
applied is at full line level.
Whenusingthisapplicationanappropriatescreenedcableisrequiredtoreducethepossibilityofexternal
signal interference.
Note.ThewiredinputAux1terminalisinparallelwiththe3.5mmJackInputonthefrontpanel;ifeither
inputsareconnectedandasignalispresentonboth,thenthetwosourceswillbemixedtogether(This
shouldbeclearlyexplainedtotheuser).
ThewiredinputAUX2terminalisinparallelwiththeBluetoothreceiver.Ifeitherinputsareconnectedor
inusethenthetwosourceswillbemixedtogether.
AjumperisprovidedtoallowtheAVID3ACBTtobeusedineithermonoorstereomode,thefactorydefault
isstereo.Ifsettomonotheamplifierwillprovideamixedoutputtoeachloudspeakerterminal.
LoudspeakersshouldbewiredtotheL+L-andR+R-terminals,ensuringthephaseofeachloudspeaker
is the same.
Thelineoutputisstereoandprovidesafixedlineoutputsignalforfeedingandexternalsourcesuchasa
slave amplifier or induction loop system.
Ifyouare experiencing anyproblemsplease contactyourreseller or the CIE-GroupTechnicalSupport
Departmenton+44(0)1159770075.
Introduction:
BeforeinstallationpleaseremovetheFaciaTrimPlatefromaroundthefrontedgeoftheunit.Thiscanbe
refitted once the installation is finished and any decorating is completed. Please note: The pair code for
Bluietoothconnectivityislocatedbehindthistrimplate.
ThecompactdepthoftheAVID3ACBTunitwillallowinstallationintostandardUK2-gangEOboxes,witha
minimumof40mmdepth.AplasticEOboxisnowincludedforrecessedinstallation.
Thesemaybegalvanisedmetalforinstallationinsolidconstructionwalls,plasticdrylining(withlugs)or
maybeinstalledintosurfacemountingDado-typetrunkingsystemsusingtheappropriatefixings.
Front Panel Controls and Connectivity:
3 illuminated buttons allow basic control of the AVID3, the bottom button (     ) controls the ON/OFF
function,theup/downbuttons()controlVolumeUpandVolumeDown.
Astereo3.5mmJackinputisprovidedonthefrontpanel,twofurtherhardwiredinputsareprovidedto
the rear of the AVID3ACBT plus a Bluetooth receiver.
TheHi/Loswitchadjuststheinputsensitivityfrom1v(LineLevel)to200mv(averageHeadphoneoutput
level),allowingtheinterfaceofgenericMP3,CDandmediaplayerswithoutlossofsystemvolumelevel.
AclearLCDDisplayshowsthedesiredvolumelevelbetween0(nooutput)to20(maximumoutput)aswell
asshowingwhichinputisinuse(S1/S2).
Fascia
Trim
Plate
Hi/Lo Line
Level
Sensitivity
Switch
IR
Receiver
Window
Audio Level
& Input
selection
Display
Volume
Level
Up
Volume
Level
Down
ON/OFF
Switch/
Input Select
3.5mm
Jack
Input
Bluetooth
active LED
/