RAMSET SG 125E Operator's Manual And Maintenance Instructions

Brand: RAMSET

Model: SG 125E

Type: Operator's Manual And Maintenance Instructions

RAMSET SG 125E is a powerful angle grinder that allows for quick and efficient grinding of various surfaces, making it suitable for a wide range of applications in construction, metalworking, and other industries. Here are some key features and use cases for this device:

High Power: The SG 125E boasts an impressive 1800W motor, providing ample power for demanding grinding tasks. It operates at a no-load speed of 10000 rpm, ensuring fast and effortless grinding.
Versatility: The grinder is equipped with a standard M14 connection, allowing you to use a wide variety of grinding accessories such as cup wheels and brushes. This versatility makes it suitable for grinding different materials, including concrete, metal, and stone.

High Power: The SG 125E boasts an impressive 1800W motor, providing ample power for demanding grinding tasks. It operates at a no-load speed of 10000 rpm, ensuring fast and effortless grinding.
Versatility: The grinder is equipped with a standard M14 connection, allowing you to use a wide variety of grinding accessories such as cup wheels and brushes. This versatility makes it suitable for grinding different materials, including concrete, metal, and stone.

Operator’s manual and

maintenance instructions

SG 125E

1. Motor

2. Switch

3. Brush

4. Detachable part of brush

5. Cup Wheel

6. Flange M 14

7. Locking buton

8. Handle

9. Dust cap

10. Connection Ø 35 mm dust extractor

11. Cable

SG 125E

Our goods come with guarantees that cannot be excluded under the Australian and

New Zealand Consumer Laws. You are entitled to a replacement or refund for a major

failure and for compensation for any other reasonably foreseeable loss or damage.

You are also entitled to have the goods repaired or replaced if the goods fail to be of

acceptable quality and the failure does not amount to a major failure.

TECHNICAL SPECIFICATIONS

Power 1800 W

Voltage 230 V

Frequency 50-60 Hz

Current 8 A

No load speed 10000 rpm

Maximum drill potential Ø 125 mm

Connection M14

Double insulation class II

Thermal safety mechanism yes

Cable 3,05 m

Weight 5,5 kg

Lubrication grease

Dust extractor connection 36 mm

Front end detachable to reach wall sides and corners

Double handle for perfect stability

Noise and vibration

The measurements recorded conform to the European standard 50144:

Noise (Lpa) 99 dB

Noise (Lwa) 86 dB

Wear ear-protectors!!

Conrmation declaration

We declare in sole responsibility that the product type Ramset SG 125E referred to

in this declaration conforms to the following standards and further normative

documents.

We declare under our sole responsibility that this product is in conformity with the

following standards or standardization documents:

EN 61000-3-2 / EN 61000-3-3

EN 50082-1

EN 55014-1/A1 / EN 55014-1/A2 / EN 55014-2

EN 55104

89/336/EEG

Paul van Beek Ruben Bernaert

General Manager Product Manager

ITW Heger

Industriepark

Cardijnlaan 3

BE-8600 Diksmuide

Belgium

PREPARING FOR USE

To prevent health problems the RAMSET SG 125E concrete grinder must be

connected to an industrial vacuum cleaner (connection diameter 36 mm).

Best results are obtained if not too much pressure is exerted on the surface being

ground.

For direct grinding against a wall the front end of the dust cap can be removed by

means of a turnbuckle. This also makes it easier to work on less accessible places.

Caution!

Any other grinding work may only take place with a completely fitted protective

cover.

The start-up limiter ensures the normal starting of the machine.

If permanently overloaded the motor overheats and the machine switches off. In this

case the machine can only be used again after a cooling timed (3-5 minutes).

Changing the cup wheel

First and foremost the removable front of the dust cap must be removed. Then open

the lock and remove the detachable front of the dust cap. The spanner (1) Ø 32 can

 nowbeusedtolocktheangebetweenthemachineandthecupwheel.

 Thespanner(2)canbeusedtoloosenthexingnut.Replacementtakesplacein

reverse order.

Changing the brush ring

When worn to 5mm the whole brush ring must be changed for a new one. To do this

 oneloosensthethreexedbrushringxingscrewsandthetwoscrewsofthefrontof

the brush ring to remove the brush. The new brush ring is pressed in and one

 retightensthevescrews.(Newbrusheshavealengthof15mm.)

Bringing into use

The power source voltage must correspond to the information on the machine.

Machines specifying 230 V can also work on 220 V.

Switching on and off

Quick-break switching

Switching on: press on/off switch.

Switching off: release on/off switch.

Button lock

Switching on: press the on/off switch and lock with the button.

Switching off: again press then release the on/off switch.

MAINTENANCE AND SERVICE

All maintenance and repairs must be carried out by the RAMSET Customer Service or a

servicer explicitly authorised by RAMSET.

The tool is designed in such a way that a minimum of maintenance and service is

required.

CAUTION: THE FOLLOWING POINTS MUST BE RESPECTED:

- The machine must be kept clean. Regularly blow out the machine.

- No other parts may be added to the machine.

- After having worked for approximately 300 hours the brushes must be checked by

a professional. The length of a new brush is 17 mm. With a length of less than 5 mm

it must be replaced by new original brushes. The cleaning of the motor part and

the application of new grease is required after approximately 300 hours.

Because after this period a complete whole overhaul is required, the machine is to be

taken to a RAMSET service centre.

ITW Construction Systems Australia Pty. Ltd.

296-298 Maroondah Highway

Victoria 3138

Australia

Victoria

Mooroolbark

296-298 Maroondah Highway

VIC 3138

Call 1300 780 063

Richmond

96 Church Street

VIC 3121

Call 1300 780 063

New South Wales

Silverwater

71 Carnarvon Street

NSW 2128

Call 1300 780 063

Mascot

563 Gardeners Road

NSW 2020

Call 1300 780 063

Newcastle

Cardiff

77 Munibung Road

Cardiff 2285

Call 1300 780 063

Australian Capital Territory

Fyshwick

5/19 Tennant Street

ACT 2609

Call 1300 780 063

Queensland

West End

281 Montague Road

Qld 4101

Call 1300 780 063

Townsville

153 Ingham Rd

QLD 4810

Call 1300 780 063

South Australia

Hilton

115 Sir Donald Bradman Drive

SA 5033

Call 1300 780 063

Western Australia

Welshpool

1/12 Colin Jamieson Drive

Welshpool WA 6106

Call 1300 780 063

Whangarei

2A Herekino St

P.O. Box 133

Whangarei

Phone 09 438 2010

North Shore

5J Miro Place, Albany

P.O. Box 40-031

Auckland 0747

Phone 09 444 2354

Auckland

35 Station Rd, Penrose

P.O. Box 12-327, Auckland 1330

Phone 09 579 3072

Henderson

123 Central Park Drive

P.O. Box 83-135, Auckland 1330

Phone 09 838 9865

East Tamaki

Unit 1, 333 East Tamaki Road

P.O. Box 97823

Sth Auckland Mail Centre

Phone 09 272 4701

Hamilton

15 Somerset St

P.O. Box 1157

Phone 07 847 9047

Tauranga

Unit 1, 15 Portside Drive

Mt Maunganui

Phone 07 572 0520

Rotorua

Waterford Park Estate

50 Old Taupo Rd

P.O. Box 855

Phone 07 348 0190

New Plymouth

25B Hurlstone Drive

P.O. Box 4148

Phone 06 759 8984

Palmerston North

601 Tremaine Avenue

P.O. Box 436

Phone 06 357 6745

Napier

124 Taradale Road

P.O. Box 3374, Onekawa

Phone 06 843 0067

Lower Hutt

46 Victoria St

Phone 04 569 7247

Wellington

147 Taranaki St

P.O. Box 3296

Phone 04 384 4138

Nelson

2 Parere St

P.O. Box 1080

Phone 03 548 2664

Christchurch

7 O’Shannesey Place

Phone 03 341 8710

Dunedin

5 Melbourne St

P.O. Box 2227

Phone 03 455 1134

Queenstown

200 Glenda Drive,

Frankton

Queenstown

P.O. Box 2469, Wakatipu

Phone 03 442 8073

Invercargill

121 Clyde St

P.O. Box 673

Phone 03 218 9241

LOCATIONS

RAMSET AUSTRALIA RAMSET NEW ZEALAND

RAMSET SG 125E Operator's Manual And Maintenance Instructions

Brand: RAMSET

Model: SG 125E

Type: Operator's Manual And Maintenance Instructions

High Power: The SG 125E boasts an impressive 1800W motor, providing ample power for demanding grinding tasks. It operates at a no-load speed of 10000 rpm, ensuring fast and effortless grinding.
Versatility: The grinder is equipped with a standard M14 connection, allowing you to use a wide variety of grinding accessories such as cup wheels and brushes. This versatility makes it suitable for grinding different materials, including concrete, metal, and stone.

Download PDF

report

RAMSET SG 125E Operator's Manual And Maintenance Instructions

RAMSET SG 125E Operator's Manual And Maintenance Instructions

Related papers

Other documents