2. Computers & electronics
  3. Telecom & navigation
  4. Mobile phones
  5. Car kits
  6. NORTHSTAR
  7. Hose Reel Mount for Pressure Washers

NORTHSTAR Hose Reel Mount for Pressure Washers Owner's manual

  • Hello! I've reviewed the user manual for the NorthStar Hose Reel Mount Kit 157823. This document provides detailed instructions for assembling and installing the kit, including a guide to determine if drilling is needed for your specific pressure washer model, as well as a list of compatible hose reels. I'm ready to answer your questions about the product.
  • What should I do before assembly?
    Do all pressure washer models require drilling?
    What fasteners are included for mounting the hose reel to the mount?
M157823B-US
TM
FIG02825
ENGINE AND PUMP REMOVED
FROM FIGURE FOR CLARITY.
FIG02843
NorthStar 157823 HOSE REEL MOUNT KIT MANUAL
Instructions:
1.) Remove contents from package.
2.) Bolt (1), (2), (3), & (4) to (5) using provided fasteners (6) & (7). Leave all fasteners loose until the final step.(See FIG02825 & 02850)
3.) Refer to ‘TABLE A’ to determine if drilling is required to attach Hose Reel Mount Kit to your pressure washer.
4.) If the model you are attaching your Hose Reel Mount Kit to is not highlighted (SEE TABLE A) proceed to step 5.
If the model of your pressure washer is highlighted, proceed to step 10.
5.) Remove fastener (9) from your pressure washer. (See FIG02843)
6.) Fit Hose Reel Mount Kit onto pressure washer as shown in FIG02843.
7.) Attach Front Right Tube (2) with provided fasteners (6) & (7).
8.) Attach Front Left Tube (4) by reusing existing fastener (9). (If you do not have fastener (9) use (6) & (7)).
9.) Attach back tubes (1) & (3) with the provided fasteners (8) & (6). Remember to tighten all fasteners when fully assembled.
10.) (FOR PRESSURE WASHER MODELS HIGHLIGHTED IN TABLE A) Hold Hose Reel Mount Kit into desired position on unit.
Use FIG02843 as a guide. Mark the hole locations of the Hose Reel Mount Kit onto your pressure washer.
11.) Drill four 11/32” holes in the places you marked on your pressure washer.
12.) Follow steps 6 thru 9.
NOTE:
• When purchasing a hose reel for this mount kit, refer to ‘TABLE B’ for compatible NORTHERN TOOL + EQUIPMENT hose reels.
• When installing a hose reel refer to FIG02843 as a guide. Fasteners for mounting a hose reel are not provided in this kit.
HOSE REEL MOUNT KI
T
REF Part No. Description Qty
1. 779865 BACK RIGHT TUBE 1
2. 779864 FRONT RIGHT TUBE 1
3. 779867 BACK LEFT TUBE 1
4. 779866 FRONT LEFT TUBE 1
5. 779897 REEL PLATFORM 1
6. 82020 5/18-18 NYLON INSERT NUT 8
7. 82233 5/16-18 X 2 CARRIAGE BOLT 6
8. 82015 5/16-18 X 3/4 HHSF 2
Com
p
onent List for 157823
153000
1571518
153001
COMPATIBLE
NORTHERN TOOL + EQUIPMENT
HOSE REEL ITEM NUMBERS 153002
TABLE B
TABLE A
WORKS WITH THE FOLLOWING
NORTHSTAR PRESSURE WASHERS
1573001 1573011 157300 157301
1573021 1577543 157302 1578111
1577544 1578112 1578201 1578301
1578172 1578132 1578171 1578131
1578182 1578152 1578181 1578151
1578202 HIGHLIGHTED MODELS REQUIRE
SOME DRILLING.
FIG02850
FRONT
BACK
reel shown not part of kit
3ft hose sold separate thru NTE item
# 1591519
/