Sanyo PDG-DSU20E User manual

Category
Data projectors
Type
User manual
MODEL/MODÈLE/MODELO/MODELL/MODELLO
PDG-DSU20N/DSU20E/DSU20B
Multimedia Projector
Projecteur Multimédia
Multimedia-Projektor
Proyector Multimedia
Proiettore Multimediale
Owner's Manual/Mode d'emploi/
Bedienungsanleitung/Manual del usuario/
Manuale d'uso
EN-1
To the Owner
Before operating this projector, read this manual
thoroughly and operate the projector properly.
This projector provides many convenient
features and functions. Operating the projector
properly enables you to manage those features
and maintains it in better condition for a
considerable time.
Improper operation may result in not only shortening
the product-life, but also malfunctions, fire
hazard, or other accidents.
If your projector seems to operate improperly,
read this manual again, check operations and
cable connections and try the solutions in the
"Troubleshooting" section in the end of this
booklet. If the problem still persists, contact
the dealer where you purchased the projector
or the service center.
READ AND KEEP THIS OWNER’S MANUAL
FOR LATER USE.
Safety Precaution
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
- This projector produces intense light from
the projection lens. Do not stare directly
into the lens, otherwise, eye damage could
result. Be especially careful that children
do not stare directly into the beam.
- Install the projector in a proper position. If
not, it may result in a fire hazard.
- Provide appropriate space on the top,
sides and rear of the projector cabinet for
allowing air circulation and cooling
the
projector. Minimum clearance must be
maintained. If the projector is to be built into a
compartment or similarly
enclosed, the
minimum distances must be maintained.
Do
not cover the ventilation slot on the
projector. Heat build-up can reduce the
service life of your projector, and can also
be dangerous.
- If the projector is not to be used for an
extended time, unplug the projector from
the power outlet.
CAUTION
DO NOT SET THE PROJECTOR IN
GREASY, WET, OR SMOKY CONDITIONS
SUCH AS IN A KITCHEN TO PREVENT A
BREAKDOWN OR A DISASTER. IF THE
PROJECTOR COMES IN CONTACT WITH
OIL OR CHEMICALS, IT MAY BECOME
DETERIORATED.
1
5 cm
SIDE and TOP
REAR
90 cm 30 cm 30 cm
EN-2
NL
Your SANYO product is designed
and manufactured with high
quality materials and components
which can be recycled and
reused.
This symbol means that electrical
and electronic equipment, at their
end-of-life, should be disposed of
separately from your household
waste.
Please dispose of this equipment at your local
community waste collection/recycling centre. In
the European Union there are separate
collection systems for used electrical and
electronic products.
Please help us to conserve the environment we
live in!
NOTE: This symbol and recycle system are applied to EU
countres only and not applied to the countries in the
other area of the world.
CAUTION
Not for use in a computer room as defined in the
Standard for the Protection of Electronic
Computer/Data Processing Equipment, ANSI/
NFPA 75.
Ne peut
être utilisé dans une salle d’ordinateurs
telle que d
éfinie dans la norme ANSI/NFPA 75
Standard for Protection of Electronic Computer/
Data Processing Electronic.
Voor de klanten in Nederland
Bij dit produkt zijn batterijen geleverd.
Wanneer deze leeg zijn, moet u ze niet
weggooien maar inleveren als KCA.
Notes on Litium Battery (CARIFORNIA
USA ONLY)
This product uses a Litium Battery which contains
Perchlorate Material - special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
Notas acerca de pilas de Litio (SOLO
CARIFORNIA, EE.UU.)
Este producto usa una pila de litio que contiene
el material perclorato - puede ser necesario una
manipulati
ó
n especial.
Consulte la p
á
gina
www.dtsc.ca.gov/hazardouswaste/perchlorate.
SANYO FISHER Sales (Europe) GmbH
Stahlgruberring 4, D-81829 München,
Germany
SANYO Electric Co., Ltd.
1-1, Sanyo-cho, Daito City, Osaka 574-8534,
Japan
EN-3
Safety Instructions
All the safety and operating instructions should be
read before the product is operated.
Read all of the instructions given here and retain
them for later use. Unplug this projector from AC
power supply before cleaning. Do not use liquid or
aerosol cleaners. Use a damp cloth for cleaning.
Follow all warnings and instructions marked on
the projector.
For added protection to the projector during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the
wall outlet. This will prevent damage due to
lightning and power line surges.
Do not expose this unit to rain or use near
water... for example, in a wet basement, near a
swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
Do not place this projector on an unstable cart,
stand, or table. The projector may fall, causing
serious injury to a child or adult, and serious
damage to the projector. Use only with a cart or
stand recommended by the manufacturer, or sold
with the projector. Wall or shelf mounting should
follow the manufacturer's instructions, and should
use a mounting kit approved by the manufacturers.
An appliance and cart
combination should be moved
with care. Quick stops,
excessive force, and uneven
surfaces may cause the
appliance and cart combination
to overturn.
Slots and openings in the back and bottom of the
cabinet are provided for ventilation, to ensure
reliable operation of the equipment and to protect
it from overheating.
The openings should never be covered with cloth
or other materials, and the bottom opening
should not be blocked by placing the projector on
a bed, sofa, rug, or other similar surface. This
projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in
installation such as a book case unless proper
ventilation is provided.
Never push objects of any kind into this projector
through cabinet slots as they may touch
dangerous voltage points or short out parts that
could result in a fire or electric shock. Never spill
liquid of any kind on the projector.
Do not install the projector near the ventilation
duct of air-conditioning equipment.
This projector should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supplied, consult your authorized dealer or local
power company.
Do not overload wall outlets and extension cords
as this can result in fire or electric shock. Do not
allow anything to rest on the power cord. Do not
locate this projector where the cord may be
damaged by persons walking on it.
Do not attempt to service this projector yourself
as opening or removing covers may expose you
to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
Unplug this projector from wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a When the power cord or plug is damaged or
frayed.
b If liquid has been spilled into the projector.
c If the projector has been exposed to rain or
water.
d If the projector does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the projector to normal operation.
e If the projector has been dropped or the cabinet
has been damaged.
f When the projector exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer that have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or
injury to persons.
Upon completion of any service or repairs to this
projector, ask the service technician to perform
routine safety checks to determine that the
projector is in safe operating condition.
EN-4
Air Circulation
Openings in the cabinet are provided for
ventilation and to ensure reliable operation of
the product and to protect it from overheating,
and these openings must not be blocked or
covered.
CAUTION
Hot air is exhausted from the exhaust vent.
When using or installing the projector, the
following precautions should be taken.
- Do not put any flammable object or spray
can near the projector, hot air is exhausted
from the ventilation holes.
- Keep the exhaust vent at least 90 cm away
from any objects.
- Do not touch a peripheral part of the
exhaust vent, especially screws and
metallic part. This area will become hot
while the projector is being used.
- Do not put anything on the cabinet.
Objects put on the cabinet will not only get
damaged but also cause fire hazard by
heat.
Cooling fans are provided to cool down the
projector. The fans’ running speed is changed
according to the temperature inside the
projector.
Installing the Projector in Proper Position
Install the projector properly. Improper
Installation may reduce the lamp life and
cause a fire hazard.
Moving the Projector
When moving the projector, replace the lens
cap and retract the elevator foot to prevent
damage to the lens and cabinet. When the
projector is not in use for an extended period,
put it into a suitable case with the lens side up
to protect the projector.
When handling the projector, do not drop,
bump, subject it to strong forces, or put other
things on the cabinet.
USE CAUTION IN CARRYING OR
TRANSPORTING THE PROJECTOR
- Do not drop or bump the projector,
otherwise damages or malfunctions may
result.
- When carrying the projector, use a suitable
carrying case.
- Do not transport the projector by using a
courier or transport service in an unsuitable
transport case. This may cause damage to
the projector. To transport the projector
through a courier or transport service,
consult your dealer for their information.
- Do not put the projector in a case before
the projector is cooled enough.
Do not tilt the projector side-
ways.
Do not point the projector up to
project an image.
Do not point the projector down
to project an image.
Do not put the projector on
either side to project an image.
Do not pitch the projector more
than 6 degrees backward and
forward.
EN-5
Compliance
Federal Communications Commission Notice
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.Do
not make any changes or modifications to the equipment unless otherwise specified in the instructions.
If such changes or modifications should be made, you could be required to stop operation of the equipment.
Model Number: PDG-DSU20N
Trade Name: Sanyo
Responsible party: SANYO FISHER COMPANY
Address: 21605 Plummer Street, Chatsworth, California 91311
Telephone No.: (818)998-7322
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirement for use in the country you
purchased it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the
Underwriters Laboratories (UL) and certified by the Canadian Standard
Association (CSA).AC Power Cord has a grounding-type AC line plug. This is
a safety feature to be sure that the plug will fit into the power outlet. Do not try
to defeat this safety feature. Should you be unable to insert the plug into the
outlet, contact your electrician.
GROUND
AC Power Cord for the United Kingdom:
This cord is already fitted with a moulded plug
incorporating a fuse, the value of which is
indicated on the pin face of the plug. Should the
fuse need to be replaced, an ASTA approved BS
1362 fuse must be used of the same rating,
marked thus . If the fuse cover is detachable,
never use the plug with the cover omitted. If a
replacement fuse cover is required, ensure it is of
the same colour as that visible on the pin face of
the plug (i.e. red or orange). Fuse covers are
available from the Parts Department indicated in
your User Instructions.
If the plug supplied is not suitable for your socket
outlet, it should be cut off and destroyed.
The end of the flexible cord should be suitably
prepared and the correct plug fitted.
WARNING : A PLUG WITH BARED FLEXIBLE
CORD IS HAZARDOUS IF ENGAGED IN A
LIVE SOCKET OUTLET.
The Wires in this mains lead are coloured in
accordance with the following code:
Green-and-yellow .....Earth
Blue ..........................Neutral
Brown .......................Live
As the colours of the wires in the mains lead of
this apparatus may not correspond with the
coloured markings identifying the terminals in
your plug proceed as follows:
The wire which is coloured green-and-yellow must
be connected to the terminal in the plug which is
marked by the letter E or by the safety earth
symbol or coloured green or green-and-yellow.
The wire which is coloured blue must be
connected to the terminal which is marked with
the letter N or coloured black.
The wire which is coloured brown must be
connected to the terminal which is marked with
the letter L or coloured red.
WARNING: THIS APPARATUS MUST BE EARTHED.
ASA
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY
ACCESSIBLE.
EN-6
Notes on the AC Power Cord
AC Power Cord must meet the requirement of countries where you use this projector. Please
confirm your AC plug type with the graphics below and ensure that the proper AC Power Cord is
used. If the supplied AC Power Cord does not match your AC outlet, please contact your sales
dealer. This projector is equipped with a grounding type AC line plug. Please ensure that your
outlet fits the plug. Do not defeat the safety purpose of this grounding type plug. We highly
recommend using a video source device also equipped with a grounding type AC line plug to
prevent signal interference due to voltage fluctuations.
Ground
EN-7
CONTENTS
CONTENTS .......................................................................................................................... 7
Introduction .........................................................................................................................8
Projector Features .......................................................................................................................8
Package Contents .......................................................................................................................9
Projector Overview ....................................................................................................................10
Using the Product ........................................................................................................12
Control Panel .............................................................................................................................12
Connection Ports .......................................................................................................................13
Remote Control ..........................................................................................................................14
Replacing the Battery ................................................................................................................15
Remote Control Operation .........................................................................................................16
Installation ..........................................................................................................................17
Connecting the Projector ...........................................................................................................17
Powering On/Off the Projector ...................................................................................................18
Adjusting the Projector ...............................................................................................................19
Menu Operation ..............................................................................................................21
Maintenance ....................................................................................................................25
Cleaning the Lens ......................................................................................................................25
Cleaning the Projector Housing .................................................................................................25
Replacing the Lamp ...................................................................................................................26
Specifications ................................................................................................................ 28
Appendix ............................................................................................................................ 29
LED Indicator Messages ............................................................................................................29
Compatibility Modes ..................................................................................................................30
Troubleshooting .........................................................................................................................31
EN-8
Introduction
Projector Features
The projector integrates high-performance optical engine projection and a user - friendly
design to
deliver high reliability and ease of use.
The projector offers the following features:
Single chip 0.55" Texas Instruments DLP
®
technology
SVGA (800 x 600 pixels)
Auto image re-sizing (Auto-Sync.) to 800 x 600 full screen with scaling compression
compatibility for VGA, SVGA, XGA* and SXGA*
Compatibility with Macintosh
®
computers
Compatibility with NTSC, PAL, SECAM and HDTV
D-Sub 15-pin terminal for analog video connectivity
User-friendly, multi-language on-screen display
Advanced electronic keystone correction
* means compressed.
DLP is a registered trademark of Texas Instruments.
EN-9
Package Contents
When you unpack the projector, make sure you have all these components:
Projector with Lens Cap AC Power Cord
VGA Cable (D-SUB to D-SUB)
(USA: J2552-0109-00) (UK: J2552-0108-00) (J2552-0072-03)
(Europe: J2552-0107-00)
Remote Control (IR) Owner’s Manual Quick Start Guide
Save the original shipping carton and packing material; they will comein handy if you
ever to ship your unit. For maximum protection, repack your unit as it was originally
packed at the factory.
Accessories and components may vary by retailer and region.
EN-10
Projector Overview
Front View
Lens cap Ventilation holes
Elevator button AC power socket
Lens cap strap Zoom ring
Projection lens Focus ring
Front IR remote control sensor Control panel
Speaker Lamp cover
11
12
910
7
1 32 4
6 8
5
1
7
2 8
3 9
4 10
5
11
6
12
EN-11
Rear View
Connection ports
Kensington lock
Rear IR remote control sensor
Ventilation holes
Bottom View
Elevator foot
Ceiling mount (3-M4*6)
Tilt-adjustment foot
1 32 4
1
2
3
4
1
2
3
1
2
3
This projector can be used with a ceiling mount for support. The ceiling mount is not
included in the package.
EN-12
Using the Product
Control Panel
LED
Button Function
LAMP (Lamp LED indicator)
Refer to “LED Indicator Messages”.
TEMP (Temperature LED indicator)
Refer to “LED Indicator Messages”.
Four directional buttons
Use four directional buttons to select items or make adjustments to your selection.
ENTER
Enter to sub-menu and confirm the menu selection. Activate in Color Setting, Lamp
Counter
Reset and Factory Default menu operations.
AUTO PC
Resynchronize the projector to the input signal from a computer.
ON / STAND-BY
Turn the projector on or off.
MENU
Display or exit the on-screen display menus.
INPUT
Manually select an input source.
1 2
3
4
568 7
1
2
3
4
5
6
7
8
EN-13
Connection Ports
AUDIO IN
Connect an audio output from video equipment to this jack.
COMPUTER IN / COMPONENT IN
Connect image input signal (Analog RGB or Component) to this jack.
S-VIDEO IN
Connect S-Video output from video equipment to this jack.
VIDEO IN
Connect composite video output from video equipment to this jack.
USB
This connector is for page up & down mouse control function and firmware update.
2
3 4 51
1
2
3
4
5
EN-14
Remote Control
INPUT
Manually select an input source.
AUTO PC
Resynchronize the projector to the input
signal from a computer.
NO SHOW
Hide the screen. Press again to cancel the
NO
SHOW function.
FREEZE
Press “FREEZE” to pause the screen image.
Press again to cancel the FREEZE function.
VOLUME + / -
Adjust the volume level.
PAGE S / T(Computer mode only)
Scroll back and forth on the screen when
giving a presentation. Connect the projector
and your computer with a USB cable to use
these buttons.
MUTE
Cut off the sound temporarily. Press again
to
cancel the MUTE function.
ENTER
-
Enter to sub-menu and confirm the menu
selection. Activate in Color Setting, Lamp
Counter Reset and Factory Default menu
operations.
- Act as computer Enter button when
keyboard function is selected.
- Act as mouse left button when mouse
function is selected.
MENU
Display or exit the on-screen display menus.
ECO
Press this button to activate the eco mode.
POINTER(Computer mode only)
Toggle this button to activate keyboard
function or mouse function when your
projector
is connected with a USB cable.
ASPECT
Press this button to switch the image aspect
ratio from 4:3 to 16:9.
KEYSTONE + / -
Correct the keystone distortion.
ESC.
-
Act as computer Esc button when keyboard
function is selected.
- Act as mouse right button when mouse
function is selected.
D-ZOOM + / -
Zoom in and out the images.
IMAGE
Select PC, Movie, sRGB or User mode.
Four directional buttons
- Use four directional buttons to select items or
make adjustments to your selection.
-
Act as computer keyboard (four directional
buttons) when keyboard function is selected.
-
Act as mouse navigation when mouse
function is selected.
ON / STAND-BY
Turn the projector on or off.
1
1
9
10
13
2
3
4
5
6
7
8
18
17
16
15
14
11
12
2
3
4
5
6
7
13
8
9 14
10
15
11 16
17
12 18
EN-15
Replacing the Battery
For the first time use:
Remove the transparent insulation tape by pulling it before use.
For battery change:
1. Remove the battery holder.
2.
Remove the old Lithium coin cell and install new one (CR2025).
Ensure
that the side with the mark "+" is up.
3. Push the battery holder back into the remote control until you feel a
click.
Keep the battery out of the reach of children. There is a danger of death by accidentally
swallowing the battery.
Do not recharge the used battery or expose the battery to fire or water.
Do not dispose of the used battery along with household waste. Dispose of used
batteries according to local regulations.
Danger of explosion may happen if batteries are incorrectly replaced. Replace only with
the same type recommended by the manufacturer.
EN-16
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
Operating the projector from the front
Operating the projector from the rear
15
15
7m
15
15
7m
The remote control may not operate when there is sunlight or other strong light such
as a fluorescent lamp shining on the remote sensor.
Operate the remote control from a position where the remote sensor is visible.
Do not drop the remote control or jolt it.
Keep the remote control out of locations with excessively high temperature or
humidity.
Do not get water on the remote control or place wet objects on it.
Do not disassemble the remote control.
EN-17
Installation
Connecting the Projector
Audio Cable VGA (D-SUB) to HDTV (RCA) Cable
VGA Cable (D-Sub to D-Sub) (supplied)
S-Video Cable
USB Cable Composite Video Cable
1 4
2 5
3 6
Desktop type
Laptop type
3
5
2
6
1
1
4
When connecting cable, power cords of both a projector and external equipment
should
be disconnected from AC outlet.
The figure above is a sample connection. This does not mean that all of these devices
can or must be connected simultaneously.
The cables that come with the projector may differ from the above illustration. The
included cables are based on actual shipment delivery.
EN-18
Powering On/Off the Projector
Powering On the Projector:
1. Remove the projector lens cap.
2. Complete the AC power cord and peripheral signal cable(s) connections.
3. Press I/ button to turn on the projector.
The projector takes a minute or so to warm up.
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects
your source.
If you are connecting multiple sources to the projector simultaneously, press the
INPUT button.
Warning:
Remove the lens cap first before powering on.
Never look into the lens when the lamp is on. This can damage your eyes. It is
especially important that children are not allowed to look into the lens.
Powering Off the Projector:
1. Press I/ button to turn off the projector lamp. You will see a message
"Power off? Press
Power again"
appear on the screen.
2. Press I/ button again to confirm.
The cooling fans continue to operate for cooling cycle.
When the LAMP LED begins flashing, the projector has entered stand-by mode.
If you want to turn the projector back on, you must wait until the projector has
completed the cooling cycle and has entered stand-by mode. Once in stand-by mode,
simply press
I/
button to restart the projector.
3. Disconnect the AC power cord from the electrical outlet and the projector.
Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least for 5
minutes to turn off the projector after powering on.
When the projector is in standby mode, LAMP LED and TEMP LED will flash once
then go out, and the fan will also turn for one second. This is normal, and not a
malfunction.
EN-19
Adjusting the Projector
Adjusting the Projector Height
The projector is equipped with an elevator foot to adjust the image height.
To raise or lower the image:
1. To raise or lower the image, press the elevator button and raise or lower the front of the
projector. Release the button to lock the adjustment.
2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.
Adjusting the Projector Zoom and Focus
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.
2. Adjust the image by sliding the zoom ring.
Elevator button
Elevator foot
Tilt-adjustment foot
To avoid damaging the projector, make sure that the elevator foot and tilt-adjustment
foot are fully retracted before placing the projector in its carrying case.
The tilt-adjustment foot in the bottom of the projector will fall from the projector when you
loosen the foot to the maximum. In this case, turn it back into position. Do not let the tilt-
adjustment foot fall from the projector when making the adjustment.
Focus ring
Zoom ring
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33

Sanyo PDG-DSU20E User manual

Category
Data projectors
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI