Star Trac E Series Treadmill E-TRxe Owner's manual

Star Trac
Brand
Star Trac
Model
E Series Treadmill E-TRxe
Category
Treadmills
Type
Owner's manual
STAR TRAC FITNESS
TM
E
Series Treadmill
Install Guide
UNPACKING
Remove all parts from the shipping crate and verify that the following parts were included in your shipment:
Description Qty.
Installation Instructions E-TR & E-TRx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Tie Strap, 14* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Screw, Truss Head, #10-24 x 3/4* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Screw, Pan Head, M4x.7, 19mm* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Frame Assembly w/ Motor Shroud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Top Rail with Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Neck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Side Rail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Screw, Button Head Socket Cap, 1/4”-28 UNC x 3/8”* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Screw, Socket Head Cap, 5/16”-18 UNC x 1.0”* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Bolt, Socket Head Cap, 5/16”-18 UNC x 3.0”* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Washer, Flat, 5/16” I.D. x 1.2” O.D.* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Washer, Split Lock, 5/16”* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Hex (Allen) key, 1/4”* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Hex (Allen) key, 5/32”* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Screwdriver, Phillips, #2* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Screwdriver (blade-tip), 3/32”* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Owner’s Manual with Warranty Registration Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
*Part of included STAR TRAC tool kit.
**E-TRe & E-TRxe models will have embedded touch screen and surrounding plastics packaged separately.
Should any component not be present or if you have any operational questions, please call Star Trac’s Customer Care department at
(800) 503-1221 or USA 1-714-669-1660. Specifically refer to your treadmill serial number and model number listed below:
Serial No._________________________________________________________________________
Model No._________________________________________________________________________
NOTE: The following assembly procedure applies to the E SERIES Treadmills.
ASSEMBLY
The following tools are required for assembly: Hex (Allen) Key, 1/4”; Hex (Allen) Key, 5/32”; Screwdriver, Phillips. To assemble your
STAR TRAC E SERIES TREADMILL, just follow these steps.
NOTE: Don’t fully tighten bolts and screws until all parts are assembled.
1. Unpacking and Positioning the Frame Assembly
Remove all the packaging material so the treadmill is sitting, ready for
assembly, on the shipping crate platform. With a helper, lift the tread-
mill frame assembly from the shipping crate platform and place it in
the location where it will be used. Make sure the unit is placed near a
power outlet.
Caution: The motor shroud end of the frame assembly is very heavy.
Two people may be needed to lift this end when moving the frame
assembly.
A
SSEMBLY AND
S
ETUP
STAR TRAC E SERIES TREADMILL Install Guide
2. Installing the Neck
2a) Pop out the Front Motor Shroud Cap from the Motor
Shroud and remove the Neck Grommet and set it aside.
2b) Remove the Motor Shroud by removing the (2) #10 Truss
head screws.
2c) Insert neck as shown and fasten with (2) 5/16-18 x 3.0”, (2)
5/16-18 x 1.0” socket head screws, (4) 5/16 washers and
(4) lock washers. DO NOT fully tighten yet.
2d) Route all cables through lower neck service opening into
motor compartment. Refer to CONNECTING THE
CABLES for cable routing and connection.
STAR TRAC E SERIES TREADMILL Install Guide
Step 2a & 2b
Step 2c
Step 2d
Screws
Motor Shroud
Screws
Motor Shroud
Cap
3. Install the Display frame to the Neck
3a) Take care to route the cables from the neck carefully to
aviod pinching, mount the display unit onto the neck. Use
the 1/4” Hex Allen to install the four (4) Socket Head Cap
Screws through the neck mount into the display unit, using
the 4 inner holes. Note: Do not fully tighten yet.
3b) Connect the following wires and cables to the LED display
board as shown:
715-3678 (DC Supply Power Cable) to J20
715-3682 (C-Safe Cable) to J10
715-3781 (Main Interface Ribbon Cable) to J1
4. Install Left and Right Handrails
4a) Assemble handrail joint as shown. DO NOT fasten the (2)
#10 Button Head Socket screws until the following step is
completed.
4b) Install left handrail to the frame as shown using (3) 5/16-
18 x 1.0” socket head screws and (3) 5/16 washers.
Partially lift up the side bed covers, if necessary. Note the
orientation of the mounting plate. DO NOT fully tighten
yet. Repeat install for right handrail.
Now tighten Neck, Display and Handrail fasten-
ers. Use the following torque specifacations.
(2)5/16-18 x 3.0” Socket Head screws- 240in-lbs (27 Nm).
(12)5/16-18 x 1.0” Socket Head screws- 240in-lbs (27Nm).
(4) #10 Button Head Socket screws- 35in-lbs (4.0 Nm)
STAR TRAC E SERIES TREADMILL Install Guide
Step 4a
Step 4b
J20
J1
J10
5. Connect the Cables
5a) Locate the DC Powerboard and the Motor Control board in
the front of the treadmill.
5b) Take the cable labeled Motor Control Board (MCB) and
connect it to the MCB.
5c) Take the cable labled DC Power and connect it to the DC
Power Board.
6. Connect the Power Cable
6a) Connect the female end of the power cord to the under
side front of the treadmill.
STAR TRAC E SERIES TREADMILL Install Guide
Motor Control
Board
DC Power
Board
Step 5a
Step 5b & 5c
Step 6a
7. Final Assembly
7a) Fasten motor shroud and Side Bed Covers with (6) #10
Truss Head screws.
7b) Pop in Front Motor Shroud Cap and install Neck Grommet.
7c) Install Handrail Grommet.
STAR TRAC E SERIES TREADMILL Install Guide
Step 7a
Step 7b
Step 7c
Screws
Screws
Screws
1
2
7. Level the Tread Mill
Before you plug in the treadmill, make sure it is
where you plan to use it and it is level to the
ground. If necessary, level your treadmill using
the two adjustable feet under the tailroller.
Loosen the lock nuts, rotate the feet until the
treadmill is stabilized, and retighten the lock
nuts.
ATTENTION
Star Trac recommends that treadmills be spaced a minimum of 20.0 inches (0.5 m) apart to allow safe and easy ingress and
egress. Even more importantly, there must be at least 48 inches (1.25 m) of free space behind the treadmills.
As with any motorized equipment, the area where treadmills are located must be free of obstructions and fixtures with sharp
edges to prevent injury in the event that a user trips or loses balance and falls.
STAR TRAC E SERIES TREADMILL Install Guide
Leveling
Feet
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Star Trac E Series Treadmill E-TRxe Owner's manual

Star Trac
Brand
Star Trac
Model
E Series Treadmill E-TRxe
Category
Treadmills
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents