2. Vehicles & accessories
  3. Motor vehicle accessories & components
  4. Motorcycle Accessories
  5. Abra
  6. AK-30

Abra AK-30 User manual

  • Hello! I am an AI chatbot trained to assist you with the Abra AK-30 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
DIY Mini Amplifed Speaker KitDIY Mini Amplifed Speaker Kit
AK-30
1
DIY Mini Amplifed Speaker Kit Assembly Instrucons
1. Locate the two PCB’s and the enclosed component set for each.
LocatethenysurfacemountamplierIC’sinthecomponentsetthataretobemountedtotheboomofthe
PCB’s.
SoldertheICamplierstotheboomICpadsmakingsurethatthedotontheICisatpin1.
(SeeFig.1)
2. RefertotheenclosedPCBcomponentlayoutdiagramfortheresistorvalueplacementandthecorrectorientaon
fortheelectrolyccapacitorsonthePCBandsoldertheminplace.
Useanohmmetertomeasuretheresistorvaluesifnotsurewhichiswhich.
Notethatthereisa50KpotenometerinRP1anda10KpotenometerinRP2posion.
TheVUmeterLED’sD1,D2,D3aregreenD4isyellowandD5isred.
(SeeFig.2)
3. Locatethetwolengthsofredandblackwires.
SoldertheredtoV0+andtheblacktoV0-onP3ofbothPCB’s.
Thesearespeakeroutputsthatwillbeconnectedtothespeakers.
(SeeFig.2)
Fig.1
Fig.2
2
4. Locatethethreeconductorandfourconductorwirelengths.
Selectthethreeconductorwire(red,yellow,black)andcutitinhalf(twoequalparts).
Thiswillbeusedforthe5Vpowerconnecon.
Stripbothendstoexposethewires.
Cutotheyellowwiresonbothendsofbothwires.
Solderaredwiretothe+5VandablackwiretotheGNDconnectorP1oneachoftheboards.
5. Selectthefourconductorwire(red,green,yellow,black)andcutitinhalf(twoequalparts).
Thesewillbeusedfortheaudioinputandwillbeconnectedtothe3.5mmstereoconnector.
Stripbothendstoexposethewires.
Cutotheredwiresonbothendsofbothwires.
Ononeofthecablescutotheyellowoneachendleavingblackandgreenwires.
Ontheothercablecutothegreenoneachendleavingblackandyellowwires.
ConnecttheyellowwiretoIN+andtheblackwiretoIN-onP2ofoneoftheboards
ConnectthegreenwiretoIN+andtheblackwiretoIN-onP2oftheotherboard.
(SeeFig3)
6. Peelotheprotecvepapercoangsontheacrylicspeakerenclosurepanels.
Mountthespeakerstotheirfaceplatesusingthelargerdiameterscrewsandnuts.
SoldertheredVO+andtheblackVO-wiresonthePCB’stothespeakerterminals.
7. Installfourbrassstandoswithnutstoeachofthetworearpanels.
MountthePCB’stothestandoswiththelargerscrewswiththewiresfacingtheexitcutout.
8. Insert4oftheM2screwsintotheopeningsonthespeakerfaceplate.
AachanM2nuttoteachofthescrews.
Proceedtoinstalleachofthefoursidetopandboompanelstothespeakerpanellockinginthescrewsand
nutsintothecut-outsonthepanels.
9. Takethetwored+5VandblackGND(P1)powerwiresfrombothPCB’sandtwistthetworedwiresandthetwo
blackwirestogether.
Solderthetwored+5Vwirestothecenterpinofthe2.1mmDCpowerconnectorprovidedandthetwoGND
wirestotheoutsidegroundconnecon.
Fig.3
3
10. Takethetwoaudioinputwiresandtwisttheblackgroundleadstogether.
Solderthegreenandyellowwirestothetwoinside3.5mmstereoconnectorpinsrespecvely.
Soldertheblackwirestotheoutsidegroundconnecon.
(SeeFig.4)
11. Connectthe3.5mmtoanaudiosource.
ConnecttheUSBconnectortoacomputerportorUSBadapterandplugitintothe2.1mmDCpowerconnector
justwiredtopowerup.
Setthe50KRP1potenometertofullclockwiseposionformaximumvolume.
Withpoweronandthespeakersplaying,adjustthe10KRP2potenometersothattheredtopmostLEDVU
indicatorjustcomesonatmaximumvolume.
12. Runthepowerandaudioinputwiresthroughthecutoutontherearpanelandinstallthe
rearpanelusingtheremainingM2screwsandnuts.
(SeeFig.5)
13. Enjoythesound.
Fig.4
Fig.5
/