Panasonic SCAK600P Operating instructions
- Category
- Cassette players
- Type
- Operating instructions
This manual is also suitable for
RQT6243-1P
P
CD Stereo System
Operating Instructions
Model No. SC-AK600
Before connecting, operating or adjusting this product, please read these
instructions completely.
Please keep this manual for future reference.
PC
For U.S.A. only
The servicenter list and warranty can be found on pages
29 and 30.
Before using
2
RQT6243
Dear customer
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions
carefully.
These operating instructions are applicable to the following system.
System SC-AK600
Main unit SA-AK600
Front SB-AK600
Speakers Center SB-PC93
Surround SB-PS90
The model number and serial number of this product can be
found on either the back or the bottom of the unit.
Please note them in the space provided below and keep for
future reference.
MODEL NUMBER SERIAL NUMBER
Main unit SA-AK600
Front speakers SB-AK600
Center speaker SB-PC93
Surround speakers SB-PS90
CAUTION!
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
Table of contents
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
OR PRODUCT DAMAGE, DO NOT EXPOSE THIS
APPARATUS TO RAIN, MOISTURE, DRIPPING OR
SPLASHING AND THAT NO OBJECTS FILLED WITH
LIQUIDS, SUCH AS VASES, SHALL BE PLACED
ON THE APPARATUS.
CAUTION!
DO NOT INSTALL, OR PLACE THIS UNIT, IN A BOOKCASE,
BUILT-IN CABINET OR IN ANOTHER CONFINED SPACE.
ENSURE THE UNIT IS WELL VENTILATED. TO PREVENT
RISK OF ELECTRIC SHOCK OR FIRE HAZARD DUE TO
OVERHEATING, ENSURE THAT CURTAINS AND ANY OTHER
MATERIALS DO NOT OBSTRUCT THE VENTILATION VENTS.
CAUTION:
TO PREVENT ELECTRIC SHOCK MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
User memo:
DATE OF PURCHASE
DEALER NAME
DEALER ADDRESS
TELEPHONE NUMBER
Before using
Supplied accessories .............................................. 3
Listening caution ..................................................... 3
IMPORTANT SAFETY INSTRUCTIONS................... 4
Installation................................................................ 5
Connections ............................................................. 6
Location of controls ................................................ 7
The remote control .................................................. 8
Disc operations
Playing discs............................................................ 9
Starting play from a specific track ................................ 10
Repeat play.................................................................. 10
Program play ............................................................... 11
Other modes of play (CD Play Mode function)............. 12
Radio operations
The radio: manual tuning...................................... 13
The radio: preset tuning........................................ 14
Tape operations
Cassette tapes ....................................................... 15
Recording operations
Before recording.................................................... 16
Recording discs..................................................... 17
Recording the radio............................................... 17
Sound quality/sound field operations
Using the built-in sound quality settings............. 18
Enhancing the sound quality................................ 18
Adjusting the bass ................................................ 18
Enjoying surround sound ..................................... 19
DOLBY DIGITAL.......................................................... 20
DOLBY PRO LOGIC.................................................... 20
Before using
3
RQT6243
Please check and identify the supplied
accessories.
Use numbers indicated in parentheses when
asking for replacement parts.
(Only for U.S.A.)
To order accessories contact 1-800-332-5368
or web site (http://www.panasonic.com).
AC power supply cord ..................................................... 1 pc.
(RJA0065-1D)
FM indoor antenna ...1 pc.
(RSA0006-J)
Supplied accessories
AM loop antenna ....1 pc.
(RSA0033-1)
Remote control
transmitter ..............1 pc.
(N2QAGB000018)
Remote control
batteries ................2 pcs.
R6, AA, UM-3
THE FOLLOWING APPLIES ONLY IN THE U.S.A.:
CAUTION:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television
reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
¡Reorient or relocate the receiving antenna.
¡Increase the separation between the equipment and re-
ceiver.
¡Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
¡Consult the dealer or an experienced radio/TV technician
for help.
Any unauthorized changes or modifications to this equip-
ment would void the user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Timer and other operations
Convenient functions ............................................ 22
Using headphones (not included) ........................ 22
Turning DEMO off.................................................. 23
Auto-off function.................................................... 23
Setting the time...................................................... 23
Using the timers .................................................... 24
Using the play/record timer ..........................................24
Using the sleep timer ................................................... 25
Using other equipment.......................................... 26
Connecting other equipment ........................................ 26
Optional antenna connections...................................... 26
Listening to an external digital source .......................... 27
Listening to an external analog source ........................ 27
Recording an external source ...................................... 27
Reference
Troubleshooting guide .......................................... 28
Servicenter List (ONLY FOR U.S.A.) .................... 29
Warranty (ONLY FOR U.S.A.)................................ 30
Product Service ..................................................... 30
About discs ............................................................ 31
Maintenance ........................................................... 31
Specifications ......................................... Back Cover
Selecting fine audio equipment such as the unit you’ve just pur-
chased is only the start of your musical enjoyment. Now it’s time to
consider how you can maximize the fun and excitement your equip-
ment offers. This manufacturer and the Electronic Industries Associ-
ation’s Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the sound
come through loud and clear without annoying blaring or
distortion—and, most importantly, without affecting your sensitive
hearing.
We recommend you to avoid prolonged exposure to excessive noise.
Sound can be deceiving. Over time your hearing “comfort level”
adapts to higher volumes of sound. So what sounds “normal” can
actually be loud and harmful to your hearing.
Guard against this by setting your equipment at a safe level BEFORE
your hearing adapts.
To establish a safe level:
•
Start your volume control at a low setting.
•
Slowly increase the sound until you can hear it comfortably and
clearly, and without distortion.
Once you have established a comfortable sound level:
•
Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage
or loss in the future. After all, we want you listening for a lifetime.
Listening caution
Before using
4
RQT6243
Safety
1. Power source—Connect the unit to a power source of the type
described in these instructions or as marked on the unit.
2. Polarization—The unit is equipped with a polarized power plug
where one blade is wider than the other. This safety feature
ensures that the plug fits into your household AC outlet only one
way. If the plug doesn’t fit one way, try reversing it. If the plug
still doesn’t fit, contact an electrician to replace the obsolete
outlet. Do not attempt to defeat the safety purpose of the plug.
3. Power cord protection—Route the AC power supply cord so
that it will not be walked on or pinched by items placed on or
against it. Never take hold of the plug or cord with wet hands.
Always grasp the plug body firmly when connecting and
disconnecting it.
4. Overloading—When connecting the AC power supply cord, be
careful not to overload the household AC outlet, extension cord,
or outlet from any other device as this can result in fire or electric
shock.
5. Nonuse periods—Turn the unit off when it is not in use. Unplug
the unit from the household AC outlet if it is not to be used for a
long time. Unplug the unit during lightning storms.
6. Attachments and accessories—Use only the attachments and
accessories recommended in these operating instructions.
Installation
Placement
1. Ventilation—Situate the unit so that it receives proper ventilation.
Do not install in a confined space such as a bookcase or cabinet.
Allow at least 10 cm (4
inches) clearance from the rear of the
unit. To prevent the risk of electric shock or fire due to overheating
ensure curtains and other materials do not obstruct the unit’s
ventilation.
2. Foreign material—Ensure objects and liquids do not get into
the unit. Avoid exposing the unit to excessive smoke, dust,
mechanical vibration, and shock.
3. Magnetism—Situate the unit away from equipment and devices
that generate strong magnetic fields.
4. Stacking—Do not place heavy objects on top of this unit.
5. Surface—Place the unit on a flat, level surface.
6. Carts and stands—Use the unit only with carts
and stands recommended by the manufacturer.
Move carts with care. Sudden stops, excessive
force, and uneven surfaces can cause carts to
overturn.
7. Wall and ceiling mounting—Do not mount the unit on walls or
ceilings unless specified in the instructions.
Environment
1. Water and moisture—Do not use the unit near water, such as
near a bathtub or swimming pool. Avoid damp basements.
2. Heat—Situate the unit away from heat sources, such as radiators.
Do not situate where temperatures fall below 5°C (41°F) or rise
above 35°C (95°F).
3. Power lines—Take care when setting up an outdoor antenna
that it is not near overhead power lines, electric lights, or electri-
cal circuits, and that there is no danger of the antenna falling on
power lines, electric lights, or electrical circuits. When installing
an outdoor antenna, take extreme care not to touch such power
lines or circuits, as contact with them can be fatal.
Maintenance
(See page 31 for details.)
Unplug the unit from the household AC outlet before cleaning.
Clean with a damp cloth.
Do not use abrasive pads, scouring powders, or solvents.
Service
1. Damage requiring service —The unit should be serviced by
qualified service personnel if:
(a)The AC power supply cord or the plug has been damaged; or
(b)Objects or liquids have gotten into the unit; or
(c) The unit has been exposed to rain; or
(d)The unit does not operate normally or exhibits a marked
change in performance; or
(e)The unit has been dropped or the cabinet damaged.
2. Servicing —Do not attempt to service the unit beyond that
described in these operating instructions. Refer all other servicing
to authorized servicing personnel.
3. Replacement parts —When parts need replacing ensure the
servicer uses parts specified by the manufacturer or parts that
have the same characteristics as the original parts. Unauthorized
substitutes may result in fire, electric shock, or other hazards.
4. Safety check —After repairs or service, ask the servicer to
perform safety checks to confirm that the unit is in proper working
condition.
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the safety precautions listed below.
Keep these operating instructions handy for future reference.
4. Outdoor antenna grounding—If you connect an outdoor an-
tenna, ground the antenna system to protect against voltage
surges and built-up static charges. Section 810 of the National
Electrical Code, ANSI/NFPA No. 70-1990, provides information
about grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of ground-
ing conductors, location of antenna-discharge unit, connection to
grounding electrodes, and requirements for the grounding elec-
trode. Refer to this diagram.
ELECTRIC
SERVICE
EQUIPMENT
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC—NATIONAL ELECTRICAL CODE
Before using
5
RQT6243
B
A
120°
30° 30°
C
30–35 mm
(1
3
/16"–1
3
/8")
70 mm
(2
3
/4")
7–9 mm
(
19
/64"–
3
/8")
(
9
/32"–
23
/64")
Ø7.5–9.5 mm
Front speaker (left) Front speaker (right)
Subwoofers
Center speaker
(SB-PC93)
Front speaker (left)
(SB-AK600)
Front speaker (right)
(SB-AK600)
Surround speaker
(left) (SB-PS90)
Surround speaker
(right) (SB-PS90)
The front, center, and surround speakers should be placed
at approximately the same distance from the listening po-
sition. The angles in the diagram are approximate.
Installation
Placement of front speakers
Place so that the subwoofers face out.
Note
•
Keep your speakers at least 10mm (13/32") away from the system
for proper ventilation.
•
The subwoofers are located on the sides of the speakers.
Leave 10-cm clearance for them to be effective.
Placement of center/surround
speakers
Center speaker (SB-PC93)
The small speaker with the short cord is the center speaker.
The model numbers are printed on the back of the speakers.
Note
Do not place the center speaker on the main unit as sound quality will
be affected.
Surround speakers (SB-PS90)
The small speakers with the long cords are surround speakers.
Place on either side of listening position, or slightly to the rear, about
1 meter higher than ear level with the Panasonic logo facing towards
the listening position.
The effect varies with the type of music and music source.
C Attaching to a wall
Surround speakers can be attached to a wall.
Set the speaker onto screws and slide through bracket to lock into
position.
Note
The wall or pillar on which the speakers are to be attached should be
capable of supporting 5 kg (11 Ib.) per screw.
Notes on speaker use
L You can damage your speakers and shorten their useful life if
you play sound at high levels over extended periods.
L Reduce the volume in the following cases to avoid damage.
•
When playing distorted sound.
•
When the speakers are receiving howling from a microphone
or record player, noise from FM broadcasts, or continuous
signals from an oscillator, test disc, or electronic instrument.
•
When adjusting the sound quality.
•
When turning the unit on or off.
Positioning for best effect
How you set up your speakers can affect the bass and the sound
field. Note the following points.
•
Place speakers on flat secure bases.
•
Placing speakers too close to floors, walls, and corners can result
in excessive bass. Cover walls and windows with a thick curtain.
•
Place the front speakers at least 5 cm from walls as they have
bass reflex ports in the rear.
If irregular coloring occurs on your television
These speakers are designed to be used close to a television, but
the picture may be affected with some televisions and set-up
combinations.
If this occurs, turn the television off for about 30 minutes.
The television’s demagnetizing function should correct the problem.
If it persists, move the speakers further away from the television.
A
B
Before using
6
RQT6243
Basic connections
(for supplied
accessories)
•
Plug the AC power supply cord into a household AC outlet only
after all other connections have been made.
•
To prepare the antenna wires and speaker cords, twist the vinyl
cover tip and pull off.
1 Connect the FM indoor antenna.
Tape the antenna to a wall or column, in a position where radio
signals are received with the least amount of interference.
Note
For best reception sound quality:
An FM outdoor antenna is recommended. (See page 26.)
2 Connect the AM loop antenna.
Stand the antenna up on its base. Keep loose antenna cord
away from other wires and cords.
3 Connect the speaker cables.
A Center and surround speaker cables
B Front (L/R) speaker cables
Connect the cords to the terminals of same color.
•Never short-circuit positive (+) and negative (–) speaker wires.
•Be sure to connect only positive (red or gray) wires to positive
(+) terminals and negative (black, blue or gray with blue line)
wires to negative (–) terminals.
Incorrect connection can damage the speakers.
Caution
Use only the supplied speakers.
Using other speakers can damage the unit and sound quality
will be negatively affected.
Caution
• Use the speakers only with the recom-
mended system. Failure to do so may lead
to damage to the amplifier and/or the
speakers, and may result in the risk of fire.
Consult a qualified service person if dam-
age has occurred or if you experience a sud-
den change in performance.
• Do not attempt to attach these speakers to
walls using methods other than those
described in this manual.
4 Connect the AC power supply cord.
Note
The included AC power supply cord is for use with this unit
only. Do not use it with other equipment.
For your reference
Information you enter into the unit’s memory, except for time,
remains intact for up to a week after the AC power supply cord is
disconnected.
Connections
1
3
1
2
3
4
2
SURROUND CENTER
1
3
Gray
Blue
Gray with
blue line
Gray
R
L
FRONT
1
3
Red
Blue
Black
Gray
Blue
Red
Black
Gray
2
(L)
B
A
B
2
(R)
3
A
R
AM loop antenna
Surround speaker
(right)
(SB-PS90)
Adhesive tape
FM indoor antenna
Center speaker
(SB-PC93)
Surround speaker
(left)
(SB-PS90)
Connect the left (L)
side in the same
way.
Before using
7
RQT6243
Location of controls
No. Name Ref. page
1 AC supply indicator (AC IN)
This indicator lights when the unit is connected to the AC power
supply.
2 Standby/on switch (f/I, POWER)
Press to switch the unit from on to standby mode or vice versa.
In standby mode, the unit is still consuming a small amount of
power.
3 Record button (a REC)............................................. 17
4 Headphone jack (PHONES)...................................... 22
5 Disc direct play buttons (CD 1 ~ CD 5) ..................... 9
6 Disc tray open/close button (c OPEN/CLOSE) ........ 9
7 Disc tray
8 Digital input, PCM FIX mode select button and
indicator (DIGITAL INPUT 1/2) .......................... 20, 27
9 Dolby Pro Logic button and indicator (p PL) ....... 20
! Super sound EQ button (SUPER SOUND EQ)........ 18
Preset EQ select button (PRESET EQ) ................... 18
# Subwoofer button and indicator
(SUBWOOFER)...........................................................18
$ Display
% Volume control (VOL) ................................................. 9
& Cassette holder open button (c OPEN) ................. 15
( Cassette holder..........................................................15
) Tuner/band select button (TUNER, BAND) ............. 13
~ AUX 1/2 button (AUX 1/2) ..........................................27
+ CD skip/search, tape fast-forward/rewind, tune/preset
channel select, time adjust buttons
(g, 3/REW, f, 4/FF) ...................... 9, 13-15, 23
, Tape play button ( : TAPE) ..................................... 15
- CD play/pause button (:/ J CD ) ............................... 9
. Stop/program clear and demonstration button
(L STOP, –DEMO)..................................... 9, 11, 15, 23
20
22
19
21
18
BAND
CD
STOP
STOP
/ REW
/ REW
TUNERAUX 1/2 TAPE
/ FF
/ FF
DEMO
DEMO
17
Before using
8
RQT6243
TEST
EST
CH SELECT
CH SELECT
CH
H
LEVE
VE
L
SUBWOOFER
78
9
0
DIS
DIS
PLAY
AY
DI
DI
MME
ME
R
PLAY
AY
MODE
PROGRAM
45
6
10
MUTING
PRESET EQ
CL
CL
OCK
CK
TIMER
TIMER
PLAY
REC
REC
SLEEP
SLEEP
AUTO OFF
TO OFF
DISC
12
3
TUNER
CD
S.SOUND EQ
VOLUME
VOLUME
TAPE
DE
DE
LAY
AY
PL
AUX
DIGITAL-IN
REW
FF
2
25
24
9 ,
26
19
20
14
30
32
31
21
34
36
23
27
17
29
1210 ,
11
35
33
30
30
˚
˚
28
A
B
C
Buttons
Buttons such as 2 function in exactly the same way as the buttons
on the main unit.
No. Name Ref. page
/ Sleep timer/auto off button
(SLEEP, –AUTO OFF) ..........................................23, 25
: Numbered buttons (≥10, 1–9, 0)......................... 10, 14
; Display button (DISPLAY) .........................................10
< Dimmer button (DIMMER) .........................................22
= Digital input/AUX select button
(DIGITAL-IN/AUX) .......................................................27
? Shift button (SHIFT)
See below.
@ Clock/timer button (CLOCK/TIMER) ................... 23-25
[ Play timer/record timer button (rPLAY/REC)... 24, 25
\ Disc button (DISC) .....................................................10
] Program button (PROGRAM) ............................. 11, 14
^ Play mode select button
(PLAY MODE) ...........................................10, 12, 13, 17
Use this for selecting repeat mode, CD play mode, tune mode,
FM mode and AM beat proof.
_ Stop/program clear button (L)....................... 9, 11, 15
{ Muting button (MUTING) ...........................................22
To operate functions labeled in orange, press [SHIFT]
(?) and the corresponding button at the same time.
; Test signal button (TEST) .........................................21
< Channel select button (CH SELECT)....................... 21
> Delay time adjust button (DELAY)........................... 21
], ^ Channel level adjust buttons
(– CH LEVEL +) .....................................................21
The remote control
A
R6, AA, UM-3
7m
Transmission
window
Signal sensor
Batteries
•
Insert so the poles (+ and –) match those in the remote control.
•
Do not use rechargeable type batteries.
Do not;
•
mix old and new batteries.
•
use different types at the same time.
•
heat or expose to flame.
•
take apart or short circuit.
•
attempt to recharge alkaline or manganese batteries.
•
use batteries if the covering has been peeled off.
•
keep together with metallic objects such as necklaces.
Mishandling of batteries can cause electrolyte leakage which can
damage items the fluid contacts and may cause a fire.
If electrolyte leaks from the batteries, consult your dealer.
Wash thoroughly with water if electrolyte comes in contact with any
part of your body.
Remove if the remote control is not going to be used for a long period
of time. Store in a cool, dark place.
Replace if the unit does not respond to the remote control even when
held close to the front panel.
Use
Aim at the sensor, avoiding obstacles, at a maximum range of
7 meters directly in front of the unit.
•
Keep the transmission window and the unit’s sensor free from dust.
•
Operation can be affected by strong light sources, such as direct
sunlight, and the glass doors on cabinets.
Do not;
•
put heavy objects on the remote control.
•
take the remote control apart.
•
spill liquids onto the remote control.
B
C
9
RQT6243
Disc operations
1
2
3
4
A
B
1
4
3
DEMO
STOP,
STOP
DEMO
OPEN CLOSE
CD
1
CD
2
CD
3
CD
4
CD 5
UP
DOWN
VOL
Elapsed playing time
(Of current track number)
Number of tracks
Total playing time
Label must face upward.
Disc indicator
Playing discs
This unit can play CD-DA (digital audio) format audio CD-R and
CD-RW that have been finalized (a process that enables CD-R/
CD-RW players to play audio CD-R and CD-RW) upon completion of
recording.
It may not be able to play some CD-R or CD-RW due to the condition
of the recording.
1 Press [c OPEN/CLOSE] button.
The unit will come on automatically and the tray opens.
2 Set disc in the tray.
To continue loading CDs in the other trays
Press another [(CD 1) ~ (CD 5)] to select the required tray and
press [c OPEN/CLOSE] to open the tray.
The current tray closes and the selected tray automatically
opens.
Press [c OPEN/CLOSE] to close the tray.
3
Press [(CD 1) ~ (CD 5)] to play your
desired disc.
(If the desired CD is indicated on the display panel, the same
operation can be accomplished by pressing [:/ J CD].)
The selected disc is played.
Use the CD Play Mode function’s ALL-DISC mode to play CD
in succession. (A page 12)
4 Adjust the volume.
A To stop the disc play
Press [L STOP, –DEMO].
B When “ ” appears on the display
It indicates there are 16 or more tracks on the disc in the playing
position.
Disc indicator
The disc indicator on the display lights whenever the tray is in the
playing position whether it is loaded or not.
One touch play
If the unit is in standby mode and a disc is loaded, press [:/ J CD] or
[(CD 1) ~ (CD 5)].
The unit will come on automatically and play will start.
To pause Press [:/ J CD] during playback.
To resume playback, press [:/ J CD].
To search forward/ Hold down [g, 3/REW] (backward)
backward or [f, 4/FF] (forward) during
playback or pause mode.
To skip forward/ Press [g, 3/REW] (backward) or
backward [f, 4/FF] (forward) during
playback or pause mode.
Note
•
During 1-Disc Random play or All-Disc Random play (A page 12),
you cannot skip to tracks which have already been played.
•
During program play (A page 11), 1-Disc Random play or All-Disc
Random play, you can search forward or backward only within the
current track.
•
During program play, skipping is always in the programmed order,
whether forward or backward.
•
Always stop the changer before loading or changing discs. You
cannot change discs while a disc is playing.
•
Do not disconnect the AC power supply cord from the household
AC outlet during disc changing operation.
Track number
10
RQT6243
Disc operations
1
2
A
B
TEST
EST
CH SELECT
CH SELECT
CH
H
LE VE
VE
L
SUBWOOFER
SUBWOOFER
78
9
0
DIS
DIS
PL AY
AY
DI
DI
MME
ME
R
PL AY
AY
MO DE
PROGRA M
45
6
10
MU
MU
TINGPRESET
T
EQ
CL
CL
OCK
CK
TIMER
TIMER
PLAY
REC
REC
SLEEP
SLEEP
AUTO OFF
TO OFF
DISC
12
3
TUNER
UNER
CD
S.SOUND EQ
S.SOUND EQ
VOLUME
VOLUME
TAPE
PE
DE
DE
LAY
AY
PL
AUX
AUX
DIGITAL-IN
DIGITAL-IN
REW
FF
2
1
DISPLAY
PLAY MODE
45
12
3
DISC
78
9
0
45
6
10
12
3
TEST
DISPLAY
C
PLAY MODE
Repeat play
Remote control only
CPress and hold [PLAY MODE] before or
during play.
“REPEAT ON” and “ ” are displayed.
To cancel repeat play
Press and hold [PLAY MODE] once again. “REPEAT OFF” is
displayed and “ ” is cleared.
To repeat your favorite tracks
1. Program the tracks you want (A page 11).
2. Press and hold [PLAY MODE] and make sure “REPEAT ON” and
“ ” are displayed.
3. Press [CD :/ J]. Playback will start.
To use repeat play with CD Play Mode function
Set the desired mode (A page 12), press and hold [PLAY MODE]
before or during playback, and make sure “REPEAT ON” and “ ”
are displayed.
Playing discs
CD display
Remote control only
This function allows you to display the remaining play time of the
current track.
During play or pause mode
Press [DISPLAY].
Every time you press the button:
Elapsed play time ↔ Remaining play time
Note
When track number 25 or greater is playing, remaining play time
display shows “– –:– –”.
Starting play from a specific track
Remote control only
1 Press [DISC] and (within 10 seconds) [1]–[5]
to select the disc.
2 Select the track with the numbered
buttons.
To select a track 10 or over, press [≥10] then the two digits.
Play starts from the selected track.
Note
You cannot use this function with 1-RANDOM or A-RANDOM mode.
A
B
Remaining play time
11
RQT6243
Disc operations
1
2
A
TEST
EST
CH SELECT
CH SELECT
CH
H
LE VE
VE
L
SUBWOOFER
SUBWOOFER
78
9
0
DIS
DIS
PL AY
AY
DI
DI
MME
ME
R
PL AY
AY
MO DE
PROGRA M
45
6
10
MU
MU
TINGPRESET
T
EQ
CL
CL
OCK
CK
TIMER
TIMER
PLAY
REC
REC
SLEEP
SLEEP
AUTO OFF
TO OFF
DISC
12
3
TUNER
UNER
CD
S.SOUND EQ
S.SOUND EQ
VOLUME
VOLUME
TAPE
PE
DE
DE
LAY
AY
PL
AUX
AUX
DIGITAL-IN
DIGITAL-IN
REW
FF
3
2
45
12
3
DISC
78
9
0
45
6
10
12
3
1
4
PROGRAM
3
4
CD
Playing discs
Program play
Remote control only
You can select up to 24 tracks to play in the order you choose.
Preparation: Press [ CD :/ J ] and then [L].
1 Press [PROGRAM].
2 Press [DISC] and (within 10 seconds) [1]–[5]
to select the disc.
3 Select the track with the numbered
buttons.
To select tracks numbered 10 and over
Press [≥10] then the two digits.
Repeat steps 2 and 3 to program all tracks you want in the required
order.
Step 2 is not necessary when selecting a track from the disc current-
ly displayed.
4 Press [ CD :/ J ].
All the tracks are played in the selected order.
To exit program mode
Press [PROGRAM] while stopped.
Program contents will be saved in the memory.
To replay your program
1. Press [PROGRAM].
2. Press [CD :/ J].
To clear all programmed tracks
Press [L] in the stop mode. “CLEAR” is displayed.
If you program a track not on your CDs
The track is initially programmed, but during program play, the player
will skip that track and will continue playing from the next programmed
item.
You can do the following while the disc is stopped
•
To check program contents
While “P” is displayed (A)
Press [g/REW/3] or [4/FF/f].
Each time you press a button, the track number and program order
are displayed.
•
To add to the program
Repeat steps 2 and 3.
When “CD FULL” is displayed
24 tracks have been programmed. No further tracks can be
programmed.
Program order
Indicates program mode
Specified track number
12
RQT6243
Disc operations
1
2
TEST
EST
CH SELECT
CH SELECT
CH
H
LE VE
VE
L
SUBWOOFER
SUBWOOFER
78
9
0
DIS
DIS
PL AY
AY
DI
DI
MME
ME
R
PL AY
AY
MO DE
PROGRA M
45
6
10
MU
MU
TINGPRESET
T
EQ
CL
CL
OCK
CK
TIMER
TIMER
PLAY
REC
REC
SLEEP
SLEEP
AUTO OFF
TO OFF
DISC
12
3
TUNER
UNER
CD
S.SOUND EQ
S.SOUND EQ
VOLUME
VOLUME
TAPE
PE
DE
DE
LAY
AY
PL
AUX
AUX
DIGITAL-IN
DIGITAL-IN
REW
FF
3
2
45
12
3
DISC
1
4
3
4
CD
PLAY MODE
REW
FF
Playing discs
Other modes of play
(CD Play Mode function)
This function makes it easier for you to select specific CDs and tracks
from those loaded in the player.
There are 5 disc/track selection modes.
All-Disc mode: Plays all loaded discs in succession from the
selected disc to the final disc .
1-Song mode: Plays one selected track on the selected disc.
1-Disc Random mode: Plays one selected disc in random order.
All-Disc Random mode: Plays all loaded discs in random order.
1-Disc mode: Plays one selected disc.
Preparation: Press [CD :/ J] and then [L].
1 Press [PLAY MODE] to select the
desired mode.
Every time you press the button:
ALL-DISC: All-Disc mode
1-SONG: 1-Song mode
1-RANDOM: 1-Disc Random mode
A-RANDOM: All-Disc Random mode
1-DISC: 1-Disc mode
(The original display is restored in about 2 seconds.)
p
Proceed to step 4 when you selected A-RANDOM in step 1.
2 Press [DISC] and (within 10 seconds) [1]-[5] to
select the disc.
The CD starts if in 1-DISC, ALL-DISC or 1-RANDOM mode.
3 Only when you selected “1-SONG” in step 1
(Within 10 seconds or so)
Press [g/REW/3] or [4/FF/f] to
select the track.
4 Press [CD :/
JJ
JJ
J] to start play.
To stop play
Press [L].
When playback ends
The current play mode will retain in memory until it is changed even if
the unit is turned off.
Final disc
For example, if play starts from disc 4, disc 3 will be the “final disc”.
Order of progression:
Disc 4z5z1z2z3
Note
You can use the CD Play Mode function together with repeat play.
Remote control only
ALL-DISC 1-RANDOM1-SONG
1-DISC
A-RANDOM
Specified disc indicator
Specified track number
13
Radio operations
RQT6243
1
2
3
4
A
1
4
PLAY MODE
3
TEST
CH SELECT
CH LEVEL
SUBWOOFER
78
9
0
DISPLAY DIMMER
PLAY MODE
PROGRAM
45
6
10
MUTINGPRESET EQ
CLOCK
TIMER
PLAY
REC
SLEEP
AUTO OFF
DISC
12
3
TUNER
CD
S.SOUND EQ
VOLUME
TAPE
DELAY
PL
AUX
DIGITAL-IN
REW
FF
2
TUNER
– VOLUME +
TUNER
PLAY MODE
/ REW /
/
FF
UP
DOWN
VOL
BAND
1 Press [TUNER, BAND] to select band.
The unit comes on automatically.
Every time you press the button:
FM ↔ AM
2 Press [PLAY MODE] on the remote
control to select “MANUAL”.
Every time you press the button:
MANUAL ↔ PRESET
3 Press [g, 3/REW] or [f, 4/FF] to
select the frequency of the required
station.
“TUNED” is displayed when a radio station is tuned.
“ST” is displayed when a stereo FM broadcast is being
received.
4 Adjust the volume.
Auto tuning
Press and hold [g, 3/REW] or [f, 4/FF] for a moment until
the frequency starts changing rapidly. The unit begins auto tuning,
stopping when it finds a station.
•
Auto tuning may not function when there is excessive interference.
•
To cancel auto tuning, press [g, 3/REW] or [f, 4/FF] once
again.
If noise is excessive in FM
Remote control only
Press and hold [PLAY MODE] to display
“MONO”.
This mode improves sound quality if reception is weak, but
broadcasts will be heard in monaural.
Press and hold [PLAY MODE] again to cancel the mode.
“MONO” goes out. MONO is also cancelled if the frequency is
changed.
Turn off “MONO” for normal listening. Stereo and monaural
broadcasts are automatically played as they are received.
FM allocation setting
Main unit only
By adjusting the allocation, you can enable this tuner to receive FM
broadcasts allocated in 0.1 MHz steps.
To change the step
1 Press and hold [TUNER, BAND].
After a few seconds the display changes to a flashing display of
the current minimum frequency.
2 Continue to hold [TUNER, BAND] down.
When the minimum frequency changes, release the button.
To return to the original step, repeat the above steps.
Note
•
After changing the “allocation” setting, the frequencies you previously
preset in the memory will be cleared.
•
Sound is momentarily interrupted if you load/unload tapes while
listening to an AM broadcast.
The radio: manual tuning
A
14
Radio operations
RQT6243
Remote control only
There are two methods of presetting stations.
Automatic presetting : All the stations the tuner can receive are
preset.
Manual presetting :You can select the stations to preset and the
order they are preset in.
Up to 15 stations each can be set in the FM and AM bands.
Preparation:
Press [TUNER] to select “FM” or “AM”.
Automatic presetting
Do the following once each for FM and AM.
Preparation:
Tune to the frequency where presetting is to begin (A page 13).
Press and hold [PROGRAM].
Release the button when frequency begins to change.
The tuner presets all the stations it can receive into the channels in
ascending order. When finished, the last station memorized is tuned
in.
Manual presetting
Preset the stations one at a time.
1 Press [PROGRAM] then press [g/REW/3] or
[4/FF/f] to tune to the required station.
2 Press [PROGRAM] then press [g/REW/3] or
[4/FF/f] to select a channel.
3 Press [PROGRAM].
The station occupying a channel is erased if another station is preset
in that channel.
Selecting channels
1 Press the numbered buttons to select
the channel.
• To enter channel 10 or over
Press [j], then the two digits.
OR
1 Press [PLAY MODE] to select “PRESET”.
2 Press [g/REW/3] or [4/FF/f] to select the
channel.
2 Adjust the volume.
The radio: preset tuning
1
TEST
EST
CH SELECT
CH SELECT
CH
H
LE VE
VE
L
SUBWOOFER
SUBWOOFER
78
9
0
DIS
DIS
PL AY
AY
DI
DI
MME
ME
R
PL AY
AY
MO DE
PROGRA M
45
6
10
MU
MU
TINGPRESET
T
EQ
CL
CL
OCK
CK
TIMER
TIMER
PLAY
REC
REC
SLEEP
SLEEP
AUTO OFF
TO OFF
DISC
12
3
TUNER
UNER
CD
S.SOUND EQ
S.SOUND EQ
VOLUME
VOLUME
TAPE
PE
DE
DE
LAY
AY
PL
AUX
AUX
DIGITAL-IN
DIGITAL-IN
REW
FF
1
2
78
9
0
45
6
10
12
3
PROGRAM
2
VOLUME
PROGRAM
A
B
PLAY MODE
Preset channel
A
B
15
RQT6243
Tape operations
1
2
3
A
2
3
1
UP
DOWN
VOL
OPEN
TAPE
/ REW / FF
DEMO
STOP,
Cassette tapes
1 Press [c OPEN] and insert the cassette.
The unit comes on automatically.
Close the holder by hand.
2 Press [: TAPE] to start play.
3 Adjust the volume.
To stop the tape
Press [L STOP, –DEMO].
To play on the other side of the tape
Turn the tape over and press [: TAPE].
A To fast-forward and rewind
Press [g, 3/REW] (rewind) or [f, 4/FF] (fast-forward).
Forward
side
Cassette tape selection and care
Use normal position tapes.
High position and metal position tapes can be played, but the unit will
not be able to do full justice to the characteristics of these tapes.
•
Tapes exceeding 100 minutes are thin and can break or get caught
in the mechanism.
•
Tape slack can get caught up in the mechanism and should be
wound up before the tape is played.
•
Endless tapes can get caught up in the deck’s moving parts if used
incorrectly. Always read the instructions provided with your tapes.
16
RQT6243
Recording operations
B
A
1
OPEN
OPEN
C
3
2
Tab for side B
Normal position tape
Tab for side A
To protect tapes against further recording
Side A
Before recording
Selection of tapes for recording
Use normal position tapes.
High position and metal position tapes can be used, but the unit will
not be able to record or erase them correctly.
Erasure prevention
The illustration shows how to remove the tabs to prevent recording.
To record on the tape again, cover as shown.
How volume and sound quality affect recording
The tape you are recording is not affected whatsoever by changes in
volume and sound quality.
To erase a recorded sound
1 Press [: TAPE ] then [L STOP, –DEMO].
2 Insert the cassette with the side to be erased facing towards
you and the exposed tape facing down.
3 Press [a
REC].
A
To re-record
B
Adhesive tape
Front side
Preparatory steps
Do these steps before each recording.
Wind up the leader tape so recording can begin immediately.
Press [c OPEN] and insert the cassette to
be recorded on.
Insert with the exposed tape facing down.
C
17
Recording operations
RQT6243
B
DEMO
STOP,
REC
A
REC
C
TEST
EST
CH SELECT
CH SELECT
CH
H
LE VE
VE
L
SUBWOOFER
SUBWOOFER
78
9
0
DIS
DIS
PL AY
AY
DI
DI
MME
ME
R
PL AY
AY
MO DE
PROGRA M
456
10
MU
MU
TINGPRESET
T
EQ
CL
CL
OCK
CK
TIMER
TIMER
PLAY
REC
REC
SLEEP
SLEEP
AUTO OFF
TO OFF
DISC
12
3
TUNER
UNER
CD
S.SOUND EQ
S.SOUND EQ
VOLUME
VOLUME
TAPE
PE
DE
DE
LAY
AY
PL
AUX
AUX
DIGITAL-IN
DIGITAL-IN
REW
FF
PLAY MODE
PLAY MODE
Recording discs
You can use 1-DISC/ALL-DISC/1-SONG mode (A page 12) to make
recordings.
Preparations:
•
Do the preparatory steps (A page 16).
•
Insert the disc(s) you want to record (A page 9).
Press [:/ J CD] and then [L STOP, –DEMO].
1-DISC/ALL-DISC recording
1 Do steps 1 to 2 on page 12.
Ensure CD is stopped.
2 Press [a REC] to start recording.
The CD starts.
1-SONG recording
Do steps 1 to 3 on page 12.
Press [a REC] to start recording.
The CD starts.
To stop recording
Press [L STOP, –DEMO].
Disc play stops automatically.
If the tape finishes before the disc
The disc continues playing. Press [L STOP, –DEMO] to stop it.
To record programmed tracks
1 Program the tracks (z page 11, steps 1–3).
2 Press [a REC] to start recording.
Play starts.
To stop recording, press [L STOP, –DEMO].
Disc play stops automatically.
A
Recording the radio
Preparation: Do the preparatory steps (A page 16).
1 Tune to the required station.
(A page 13 or 14).
2 Press [a REC] to start recording.
To stop recording
Press [L STOP, –DEMO].
To record on the other side of the tape
Turn the tape over and press [a REC].
Note
When recording an AM broadcast, sound is momentarily interrupted
when you start and stop the recording.
To reduce noise while AM recording (Beat proof
function)
Remote control only
Press and hold [PLAY MODE] while recording.
Each time you press and hold the button, “BP1” and “BP2” will be
displayed alternately.
Select the position where there is less noise.
C
B
18
Sound quality/sound field operations
RQT6243
B
A
C
SUPER
SOUND EQ
PRESET
EQ
SUBWOOFER
SUPER
SOUND EQ
EQ
PRESET
SUBWOOFER
TEST
CH SELECT
CH LEVEL
SUBWOOFER
78
9
0
DISPLAY DIMMER
PLAY MODE
PROGRAM
45
6
10
MUTINGPRESET EQ
CLOCK
TIMER
PLAY
REC
SLEEP
AUTO OFF
DISC
12
3
TUNER
CD
S.SOUND EQ
VOLUME
TAPE
DELAY
PL
AUX
DIGITAL-IN
REW
FF
PRESET EQ
SUBWOOFER
S.SOUND EQ
SHIFT
Using the built-in sound quality
settings
Press [PRESET EQ] to select the sound
quality.
Every time you press the button:
HEAVY : Select this when playing rock or other kinds of music that
sounds better with an added punch.
SOFT : Select this when listening to background music.
CLEAR : Select this for jazz or other kinds of music for which clarity
in the treble range is desired.
VOCAL : Select this to add gloss to vocals.
The original display is restored on the display panel in about 4
seconds.
Note
•
Preset EQ cannot be used together with Super Sound EQ.
•
All recordings are performed at “EQ-OFF” setting even if an
alternative sound quality setting has been selected.
Enhancing the sound quality
This feature enhances the bass and treble effect of the sound.
Press [SUPER SOUND EQ].
Remote control : Press [S.SOUND EQ].
Press the button again to cancel.
A
B
HEAVY SOFT CLEAR
EQ-OFF
VOCAL
Adjusting the bass
Press [SUBWOOFER].
The button lights when the feature is on.
Remote control: Press [SHIFT] + [SUBWOOFER].
Each time you press the button:
MID (medium) → MAX (high) → Light off (off)
To cancel
Press [SUBWOOFER] to turn the light off.
Remote control: Press [SHIFT] + [SUBWOOFER].
Note
You cannot use this function when headphones are connected.
→
C
19
Sound quality/sound field operations
RQT6243
Enjoying surround sound
The following chart gives a summary of this unit’s surround features.
Note
•
All the features are only effective if speakers are used. No discernible effect will be heard through headphones.
•
None of the features are effective when radio is selected as the source.
•
You may experience a reduction in sound quality when these surround systems are used with some sources. If this occurs, turn the surround
system off.
Surround system Features Software
DOLBY DIGITAL
(➡ page 20)
•
Dolby Digital is a discrete 5.1 (6) channel
surround system developed for cinema
use.
The sound signals in Dolby Digital format
are compressed to 1/10 their original
size, allowing an entire movie to be re-
corded on a single DVD.
•
This unit automatically recognizes DVDs
that have been recorded with Dolby
Digital.
•
Not all Dolby Digital sources are record-
ed with 5.1 (6) channels.
Some sources marked Dolby Digital may
be recorded in Dolby Surround, a 2
channel system.
Software encoded with Dolby Digital can
be identified with this mark.
•
DVD
DOLBY PRO LOGIC
(➡ page 20)
Software encoded with Dolby Surround
can be identified with this mark.
•
DVD
•
Video CD, CD
•
Laser Disc
•
Video tape
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks
of Dolby Laboratories.
To calculate the delay time
D1: Distance from front speakers
D2: Distance from surround speakers
D3: Distance from center speaker
Setting the center channel delay time (Dolby Digital only):
If D1 is equal to or
Set to 0 ms.
less than D3
If D3 is less than D1
Increase 1 ms for every 30 cm (1 foot) of
difference between D1 and D3.
Setting the surround channel delay time:
If D1 is equal to or For Dolby Digital: Set to 0 ms.
less than D2 For Dolby Pro Logic: Set to 15 ms.
If D2 is less than
Start at 0 ms for Dolby Digital or 15 ms for
D1
Dolby Pro Logic, and increase by 5 ms for
every 1.5 m (5 feet) of difference between
D1 and D2.
D1
D3
D1
D2
D2
Front
speaker
(left)
Front
speaker
(right)
Center speaker
Surround speaker
(left)
Surround speaker
(right)
A Refer page 21 for operation.
Dolby Pro Logic is a decoding system that
was developed to get a better sense of
presence from sources encoded with
Dolby Surround. The balance of sound
has been improved by the addition of a
separate center speaker channel.
RQT6243
20
Listening operations
Sound quality/sound field operations
Enjoying surround sound
DOLBY DIGITAL
Preparation: Do step 1 on page 27, A..
Play a DOLBY DIGITAL source from the
external unit.
“p DIGITAL” is displayed.
DOLBY PRO LOGIC
1 Press [p PL] to select “NORMAL” OR
“PHANTOM”.
Every time you press the button:
NORMAL → PHANTOM
↑
Light off (off) ←
NORMAL: To output at the front, surround and center
speakers
PHANTOM: To output at the front and surround speakers
(sound which would have been sent to the center
speaker will be divided equally between both the
left and right front speakers.)
2 Playback a Dolby Surround source.
The program format indicators (L, C, R, LS, S, LFE, RS)
These light up to indicate the channels contained in the digital input
signal. They do not light when input is analog.
L: Front left
C: Center
R: Front right
RS: Right surround
LS: Left surround
S: If the surround channel is monaural
LFE (Low Frequency Effect): Deep-bass effect
Changing the recognition mode
In rare cases, the unit may have trouble recognizing the digital
signals on the discs. With the PCM signals on CDs, this may cause
the beginning of a track to be cut off. Engage the PCM FIX mode if
this occurs.
This mode does not need to be changed under normal
circumstances. Change it only if the unit appears to be having
trouble recognizing the software you are playing.
While the input source is selected and digital input is engaged:
Press and hold [DIGITAL INPUT 1/2].
Every time you press and hold the button:
PCM FIX ↔ AUTO
When PCM FIX mode is on, the unit cannot process other signals.
This may cause noise to be output. Select “AUTO” if this occurs.
The selected mode is stored even if the unit is turned off.
A
B
C
B
A
C
DIGITAL
INPUT 1/2
pPL
PL
PL
DIGITAL
INPUT 1/2
1
Program format indicator
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Panasonic SCAK600P Operating instructions
- Category
- Cassette players
- Type
- Operating instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Panasonic RQSX67V Operating instructions
-
-
-
-
-
-
-
-
-
