Panasonic MC-E4061 Operating instructions

Brand: Panasonic

Model: MC-E4061

Category: Vacuum cleaners

Type: Operating instructions

This manual is also suitable for

MCE4061

Operating Instructions

Vacuum Cleaner

Model No. MC-E4061

We would advise that you carefully study these Operating Instructions before attempting

to operate the vacuum cleaner and that you note the Important Safety Instructions.

Please keep in a safe place with your Authorised Dealer Service booklet.

This product complies with the European directive 73/23/EEC and 89/336/EEC and with the Australian

Standards AS 3350.2.2 (1995) and Australian EMC requirements for the C-Tick Mark.

Matsushita Electric Industrial Co., Ltd

http://www.panasonic.co.jp/global/

CØ1ZDDD2ØEØØ

ACØ1ZDDDZØEØ

Printed in P.R.C.

REMINDER FOR CUSTOMER

The model and serial number of the product

may be found on the nameplate located at the

back of your vacuum cleaner. You should note

the model and serial number in the spaces

provided and retain this book for future

reference.

Model Number: ....................................

Serial Number:......................................

Date Purchased: ..................................

Where Purchased:................................

- 2 -

Page

• Caution for AC Mains Lead (UK and Republic of Ireland only) ..........2

• Important Safety Instructions for the user ..........................................3

• Cautions ............................................................................................3

• Identification of main parts ................................................................4

HOW TO OPERATE YOUR VACUUM CLEANER

A) How to use your folding handle ...................................................... 4

B) Mains lead release ..........................................................................5

C) ON/OFF Switch ..............................................................................5

D) Handle lock / release by foot pedal ................................................5

E) How to use the accessories ............................................................6

F) Motor protector ................................................................................6

G) Thermal cut-out................................................................................6

TABLE OF CONTENTS

Page

MAINTENANCE AND SERVICING

A) Vacuum cleaner storage ......................................7

B) Cleaning exterior and attachments ......................7

C) Dust bin cleaning and removal..............................8

D) Dust bin filter changing and cleaning ........................9

E) Cleaning secondary filter ..................................10

F) Exhaust filter cleaning ........................................10

G) Belt changing cleaning ........................................11

H) Blockages............................................................13

I) Troubleshooting guide ..........................................14

• Specifications ........................................................15

• Consumables / accessories ..................................16

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY

This appliance is supplied with a moulded three pin mains plug for your safety and convenience.

A 13 amp fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that the replacement fuse has rating of 13 amps and that it is approved

by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.

If you lose the fuse cover the plug must not be used until a replacement cover is obtained.

A replacement fuse cover can be purchased from your local Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE

SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE

ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.

If a new plug is to be fitted please observe the wiring code as shown below.

If in any doubt please consult a qualified electrician.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Blue : Neutral

Brown : Live

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or

coloured RED.

Under no circumstances should either of these wires be connected to the earth terminal of the three pin plug, marked with

the letter E or the Earth Symbol

How to replace the Fuse:

• There are two types of the supplied AC Mains Lead : A and B as shown below.

1 Open the fuse compartment with a screwdriver.

2 Replace the fuse and fuse cover if detachable.

ASA

CAUTION FOR AC MAINS LEAD (UK and Republic of Ireland only)

TYPE A TYPE B

Information on Disposal for Users of Waste Electrical & Electronic Equipment

(private households)

This symbol on the products and/or accompanying documents means that used electrical and

electronic products should not be mixed with general household waste. For proper treatment,

recovery and recycling, please take these products to designated collection points, where they will be

accepted on a free of charge basis. Alternatively, in some countries you may be able to return your

products to your local retailer upon the purchase of an equivalent new product. Disposing of this

product correctly will help to save valuable resources and prevent any potential negative effects on

human health and the environment which could otherwise arise from inappropriate waste handling.

Please contact your local authority for further details of your nearest designated collection point.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national

legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further

information.

Information on Disposal in other Countries outside the European Union

This symbol is only valid in the European Union.

If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of

disposal.

- 17 -

• Do not leave the vacuum cleaner plugged into mains socket. Unplug from the socket when not in use and before cleaning

the appliance or undertaking maintenance operations.

• This appliance is not intended for use by young children or infirm people without supervision; young children should be

supervised to ensure that they do not play with the appliance.

• Do not use if the mains lead or mains plug is damaged. If the vacuum cleaner is not working as it should be, or has been

dropped, damaged, left outdoors, or come into contact with water, consult an authorised Panasonic Service Centre.

• Do not pull or carry by the mains lead, use the mains lead as a handle, close a door on the mains lead, pull the mains lead

around sharp edges or corners. Do not run over the mains lead with the vacuum cleaner. Keep the mains lead away from

heated surfaces.

• Do not handle plug or vacuum cleaner with wet hands.

• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that

may block or reduce air flow.

• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

• Do not use the vacuum cleaner without filters and /or dust bin in place.

• Do not use wet filters after wash, see D) Dust Bin filter Changing and Cleaning.

• Turn off all controls before unplugging.

• Do not use to pick up flammable or combustible materials, or others that may become so or use in areas where they may

be present.

• This appliance should be serviced by an authorised Panasonic Service Centre, and only genuine Panasonic spare parts

should be used.

• Use extra care when cleaning on stairs. Keep hold of the handle to prevent the vacuum cleaner from falling.

• To prevent damaging carpeted floors, tiled floors, Linoleum, etc. Do not leave the beater bar rotating in the same place for

too long.

• Keep bare feet and hands away from the beater bar. (It may cause injury)

NOTE: This vacuum cleaner is designed for general household use only and is not suitable for use in a garage,

garden or to suck up liquids.

IMPORTANT SAFETY INSTRUCTIONS FOR THE USER

Before using the vacuum cleaner, please read these basic precautions.

WARNING: To reduce the risk of fire, electric shock, or injury.

CAUTION

1. To avoid any possible damage to

the mains lead, never run over the

mains lead or allow it to become

caught in the beater bar when using

the vacuum cleaner.

2. Do not run the vacuum cleaner over

tassels or fringes of rugs or mats as

they could get caught up in the beater

bar and may cause damage to belt.

3. Keep the vacuum cleaner away

from heat sources such as radiators,

fires, direct sunlight, etc.

4. To avoid damaging the vacuum

cleaner, never let the vacuum cleaner

pick up wet matter, mud, burning

ashes or large and sharp objects.

5. Do not pull on the mains lead when

disconnecting the appliance from the

mains, always pull on the plug body

itself.

6. To avoid injury, keep your fingers

and hands away from the beater bar,

and never put them between the body

parts.

- 3 -

Vacuum Cleaner Consumables / Accessories

For customers within the UK:

For customers within the Republic of Ireland:

DESCRIPTION MC-E4061

Primary filter Part number

AC95KCHPZØØØ

Exhaust filter Part number

Electrostatic AC38KCHNZØØØ

Dust bin Part number

AC42KDDDZØUØ

Dust bin cover Part number

AC2ØHCHPZVU7

Dust bin release lever Part number

AC64BCHPZVØ7

Primary filter screen Part number

AC71FCHPZVØ7

Extension wand Part number

AC7ØPCHPZVØ6

Extension wand (with tabs) Part numbers

AC4ØPCHNZVØ6

Crevice nozzle Part number

AC6ØRCHPZVØ6

Dusting brush Part number

AC88RCHPZVØ6

Belt Part number

AC28SCNZZØØØ

Beater bar ass’y Part number

AC92SCNZZUØØ

Hose Part number

AC84PCHPZVØ6

Nozzle cover latch Part number

ACØ8DCHRZVØ6

Note: Specifications are subject to change without notice.

Sales and Support Information

Customer Care Centre

• For customers within the UK: 0844 8443868

• For customers within the Republic of Ireland:

01 289 8333

• Visit our website for product information

• E-mail: [email protected]

Direct sales at Panasonic UK

• Order accessory and consumable items for your product with

ease and confidence by phoning our Customer Care Centre

Monday - Thursday 9:00am - 5:30pm, Friday 9:30am - 5:30pm

(excluding public holidays).

• Or go on line through our Internet Accessory ordering

application at www.panasonic.co.uk

• Most major credit and debit cards accepted.

• All enquiries transactions and distribution facilities are

provided directly by Panasonic UK Ltd.

• It couldn’t be simpler!

• Also available through our Internet is direct shopping for a

wide range of finished products, take a browse on our website

for further details.

- 16 -

IDENTIFICATION OF MAIN PARTS

Handle

On/Off switch

Hose

Crevice nozzle

Dust bin

release handle

Dust bin

cover

Primary filter

Primary filter screen

Dust bin

Exhaust filter

(inside)

Furniture guard

Cleaning head

Upper cord hook

Mains lead

Dusting brush

Handle release

button

Carrying handle

Suction inlet

Wands

Motor protector

Foot pedal

(handle release)

Nozzle hose

HOW TO OPERATE YOUR VACUUM CLEANER

A) HOW TO USE YOUR FOLDING HANDLE

To rotate the handle to the storage

position when the vacuum cleaner is

not in use, press handle release button

and rotate handle counter-clockwise for

easy storage.

NOTE: You should hear a noticeable

“click” sound when handle reaches the

storage position.

Never pull the vacuum cleaner with the

handle in the storage position. The

handle will drag on the floor.

Always lift the vacuum cleaner by the

carrying handle when transporting to

storage.

- 4 -

To release the handle; press the

handle release button as shown. With

the release button depressed rotate

the handle clockwise to the operating

position. Once the handle reaches the

operating position (up) it will

automatically lock into place.

NOTE: You should hear a noticeable

“click” sound when handle reaches the

operating position.

NOTE: Make sure the handle is locked

in the operating position before using the

vacuum cleaner. DO NOT operate the

vacuum cleaner unless handle is locked.

Carrying

Handle

STORING HANDLE

Handle

Release

Button

Operating

Position

Storage

Position

- 15 -

MODEL NO. MC-E4061

POWER SOURCE 230-240V / 50Hz

MAX. INPUT POWER 1800w

MOTOR PROTECTION YES

DUST BIN CAPACITY 2.4 litres

EXHAUST FILTER Electrostatic

DIMENSIONS (W x L x H) 360x375x1110

NET WEIGHT 7.3 kg

DUSTING BRUSH

YES

PIPE YES

CREVICE NOZZLE YES

AIR TURBINE NO

SPECIFICATIONS

B) MAINS LEAD C) ON/OFF SWITCH

D) HANDLE LOCK / RELEASE BY FOOT PEDAL

Release the handle by pressing down on the handle release pedal with your foot and

pulling back and down on the handle with your hand.

CAUTION: To prevent

damaging carpeted floors,

tiled floors, linoleum, etc.

Do not leave the beater bar

rotating in the same place

for too long.

Step a second time

Wrap the mains lead around the upper

and lower cord hooks and push the

mains plug under the lead.

Turn the upper cord hook to release

the mains lead.

To start or stop the vacuum cleaner,

push the switch button to ‘I’ to turn ON

and to ‘O’ to turn OFF.

NOTE: After use, unplug from the

socket and store the vacuum cleaner in

the upright position.

Quick Release

Cord Hook

On-Off

Switch

- 5 - - 14 -

TROUBLE SHOOTING GUIDE

Before contacting your Pansonic service centre, check the following points:

NOTE: Failure to correctly maintain your product, for example regular cleaning and unblocking, may result in a charge if referred

to a service agent for attention.

CAUTION:DISCONNECT from the mains socket before carrying out any kind of maintenance

operation.

TROUBLE CHECK POINT CAUSE / REMEDY

Motor fails to rotate • Mains plug connection • Check that the mains plug is connected firmly and

(no noise is heard at all) mains socket is ON.

• Mains plug fuse. (UK, IRL only) • Check fuse and replace if blown.

• Thermal cut-out device may have • (See Thermal cut-out protection feature below

operated. described).

Motor runs but there • Hose inlet is blocked. • If there is a blockage, remove it.

is no suction. see (BLOCKAGES)

• Check dust mark. • If it shows full, empty the dust bin.

• Primary filter • If the primary filter is full of dust, clean it or

replace. (see FILTER CARE)

• Check hose is properly inserted • Re-insert the hose to suction pipe inlet correctly.

to the suction pipe inlet.

• Check dust accumulated on primary • Remove dust accumulated or replace the filters.

filter. (see FILTER CARE)

• Exhaust filter. • If exhaust filter is full of dust, clean or replace it.

(see FILTER CARE)

• Dust bin inlet is blocked. • If there is a blockage, remove it.

(see BLOCKAGES)

Beater bar does not • Clogged by a large object in • If there is any obstruction, remove it.

rotate. the beater bar housing.

• Belts broken or loose. • If the belt is broken, replace it.

If loose re-install it.

THERMAL CUT-OUT

This vacuum cleaner is fitted with a thermal cut-out device which automatically turns off the vacuum cleaner to prevent

overheating of the motor. When this happens, disconnect the vacuum cleaner from the mains socket and check the dust bin and

filters as it may be full or clogged with fine dust. Check for any other obstructions.

After emptying the dust bin or removing the obstruction, leave the vacuum cleaner to cool down until the thermal cut-out resets

after approximately 40 minutes.

IMPORTANT: The thermal cut-out will not reset if the vacuum cleaner is not disconnected from the mains socket.

MAINS LEAD

IMPORTANT: If the mains lead becomes damaged, it must be repaired by Panasonic, authorised service centre or a

qualified person in order to avoid any hazard.

- 6 -

This vacuum cleaner has a thermal cut-out which

automatically trips to protect the vacuum cleaner from

overheating. If a clog prevents the normal flow of air to the

motor, the thermal cut-out turns the motor off automatically to

allow the motor to cool in order to prevent possible damage to

the vacuum cleaner.

To correct problem: If this occurs, turn the vacuum cleaner

off and unplug the vacuum cleaner from the mains outlet to

allow the vacuum cleaner to cool and the thermal cut-out to

reset. Check for and remove clogs, if necessary. Also

check and clean/replace any clogged filters. Wait

approximately forty (40) minutes before switching on the

vacuum cleaner. The motor protector will not reset if the

vacuum cleaner is not disconnected from the mains

socket even if the vacuum cleaner has cooled down.

F) MOTOR PROTECTOR

Motor

Protector

This vacuum cleaner has a motor protector by-pass valve

which automatically opens to provide cooling air to the

motor when a clog prevents the normal flow of air to the

motor. If the by-pass valve opens to prevent motor

overheating and possible damage to the vacuum cleaner,

you will notice a change of sound as air rushes through the

valve opening.

To correct problem: See the TROUBLE-SHOOTING

guide (page 14).

NOTE: The motor protector may open when using

attachments or when cleaning new carpet, due to reduced

airflow by the attachments themselves or by new carpet

fluff filling the dust bin quickly. See the TROUBLE-

SHOOTING guide (page 14).

G) THERMAL CUT-OUT

CAUTION: Do not block motor protector.

E) HOW TO USE THE ACCESSORIES

CAUTION:While using

the accessories, hold

the handle with one

hand to avoid pulling

the vacuum cleaner

over.

Lift out accessories needed.

NOTE: After having finished using the accessories, re-insert the hose to the suction pipe inlet.

To avoid accidental injury,

keep children away from the

beater bar while in

operation.

Connect any of the accessories, as indicated.

- 13 -

BLOCKAGES

Suction Inlet

Secondary

Filter Screen

Hose Inlet

Hose Coupling

The hose located on the vacuum cleaner carries the dirt

from the nozzle up to the dust bin. If the hose should

become clogged:

Unplug the vacuum cleaner from mains outlet.

Remove hose coupling and check hose coupling and hose

inlet for clogs according to the following procedure.

To remove hose coupling:

1.Depress and tilt tab A as shown.

2.Once tab A is clear of the vacuum cleaner inlet, depress

and tilt tab B as shown.

To re-install hose coupling: Reverse steps above.

Check suction inlet and secondary filter screen for clogs.

Disconnect wand from connector pipe and nozzle hose,

check the wand and hose. Plug in vacuum cleaner and turn

on.

Disconnect wand and stretch hose in and out to remove

clog. If clogs still exist, turn the vacuum cleaner over and

inspect beater bar area for clogs, see page 11 for details.

Connector

Pipe

Nozzle

Hose

To prevent damage to carpeted

floors when using tools the vacum

cleaner should not remain in one

place for a period of time .

CAUTION:

Do not use attachments if they are wet. Attachments used in dirty areas, such as under a refrigerator,

should not be used on other surfaces until they are washed. They could leave marks.

To rotate the handle to the storage position when the vacuum cleaner is not in use,

press handle release button and rotate handle counter-clockwise for easy storage.

NOTE: You should hear a noticeable “click” sound when handle reaches the storage

position.

WARNING:

Electrical Shock And Personal Injury Hazard

Wrapping the mains lead too tightly around the hooks may cause damage

to the lead. A damaged lead is an electrical shock hazard and could cause

personal injury or damage.

MAINTENANCE AND SERVICING

A) VACUUM CLEANER STORAGE

Handle

Release

Button

Operating

Position

Storage

Position

Always follow all safety precautions when cleaning and servicing the vacuum cleaner.

WARNING:

Electrical Shock And Personal Injury Hazard

Disconnect from electrical supply before servicing or cleaning the vacuum cleaner. Failure to do so could result in

electrical shock or personal injury from vacuum cleaner suddenly starting.

CLEANING EXTERIOR AND ATTACHMENTS

Disconnect mains plug from wall outlet.

Clean exterior using a clean, soft cloth that has been dipped in a solution of mild liquid detergent and water, then wrung dry. Wipe

dry after cleaning. DO NOT drip water on vacuum cleaner.

Wash attachments in warm soapy water, rinse and air dry. Do not clean in dishwasher.

DO NOT use tools if they are wet.

- 7 -

- 12 -

New

Belt

Pulley

Motor

Shaft

Beater

Bar

Nozzle

Base

End

Cap

Base

Slot

TO REPLACE BELT

Seat left end of beater bar into nozzle base. To seat beater

bar end, place rounded portion of beater bar end cap down

into slot in nozzle base.

Loop the new belt on the motor shaft.

Loop the other end of belt onto the belt pulley on the right

end of beater bar.

Pull right end of beater bar forward and seat it into nozzle

base.

Beater

Bar

Belt

Press firmly, checking to see that each end is completely

inserted.

Check to see that the belt is centered on the belt pulley and

that the beater bar turns freely.

Nozzle

Cover

Nozzle Cover

Retainer

Make sure the nozzle cover retainers are in the UNLOCK

position. Hook the front of the nozzle cover on to the nozzle

base and rotate downward. Once in place, rotate the nozzle

cover retainers to the LOCK position.

CAUTION

Moving parts! To reduce the risk of

personal injury, DO NOT touch the

agitator when vacuum cleaner is on.

Contacting the agitator while it is

rotating can cut, bruise or cause

other injuries. Always unplug from

electrical outlet before servicing.

Use caution when operating near

small children.

- 8 -

Dust Bin

Lid

TO REPLACE DUST BIN LID

Place dust bin lid assembly back onto top of dust bin. Align

marks with bin marks as shown. Rotate lid clockwise while

pressing downward so that marks align as shown.

TO REPLACE DUST BIN

First align base of dust bin with the vacuum cleaner. Lift the

release lever up and push the bin in place, then push the

lever down to lock the bin securely in place.

Lid

Unlock

Locked

DUST BIN CLEANING

TO REMOVE DUST BIN

Remove dust bin assembly from vacuum cleaner by lifting

the release lever as shown.

Remove dust bin from vacuum cleaner by tilting out as

shown.

CAUTION:

Electrical Shock And Personal Injury Hazard

Always disconnect the vacuum cleaner from mains outlet before carrying out any service or maintenance on the

vacuum cleaner.

CAUTION:

Moving parts! To reduce the risk of personal injury, DO NOT touch

the agitator when vacuum cleaner is on. Contacting the agitator

while it is rotating can cut, bruise or cause other injuries.

Always unplug from electrical outlet before servicing.

Use caution when operating near small children.

Always empty the dust bin when dirt level reaches the “MAX FILL” line.

Release

Lever

MAX Fill

Line

Separate the lid from the dust bin by lifting it straight off.

Empty contents into a waste bin.

Rotate lid counter-clockwise from the locked position to the

unlocked position as shown.

Lid

Unlock

Locked

- 11 -

BELT CHANGING AND CLEANING

WARNING:

Electrical Shock And Personal Injury Hazard

Disconnect from electrical supply before servicing or cleaning the vacuum cleaner. Failure to do so could result in

electrical shock or personal injury from vacuum cleaner suddenly starting.

Frequently check and remove hair, string and lint build-up in the brush area. If build-up becomes excessive, follow the steps below.

Should the belt become loose or should it break, follow the Belt Removal Instructions.

TO REMOVE NOZZLE COVER

Disconnect from electrical supply.

Press handle release pedal

and tilt the handle down so the vacuum cleaner is laying flat

on the floor.

To protect the floor surface, always place paper under the

nozzle any time the nozzle cover is removed.

Release the nozzle cover by rotating the nozzle cover retainers

to the UNLOCK position. Grasp back of nozzle cover on each

side and lift up to remove it from nozzle.

LOCK

UNLOCK

LOCK

UNLOCK

Nozzle

Cover

Nozzle Cover

Latches

Beater

Bar

Belt

WARNING: Personal Injury Hazard

Always unplug the vacuum cleaner before cleaning the brush area as beater bar may suddenly restart. Failure

to do so can result in personal injury.

Carefully remove any residue that may exist in the belt area.

TO REMOVE BELT/CLEAN BEATER BAR

Position hands on the beater bar. If the belt is still attached to

the beater bar, there will be tension on it.

Carefully lift the right end of the beater bar and then lift the left

end.

Remove the worn or broken belt from the motor drive shaft.

WARNING:

Personal Injury Hazard

Be careful when removing the beater bar as the belt

tension is high. Failure to do so could result in

personal injury from the beater bar releasing

quickly and snapping away.

Usage

Clean Beater bar

HEAVY - every week

(used daily)

MODERATE - every month

(used 2-3 times/week)

LIGHT - every 2 months

(used 1 time/week)

End

Cap

Cut off any carpet pile, hair or lint

entangled around the beater bar

and remove any string or debris

located near the end caps.

NOTE: In order to keep cleaning efficiency high and to prevent

damage to your vacuum cleaner, the beater bar must be

cleaned every time the belt is changed.

- 9 -

Alignment

Tab s

Alignment Tabs

DUST BIN FILTER CHANGING AND CLEANING

Check primary filter frequently and clean when dirty. Remove the dust bin assembly as outlined in the DUST BIN CLEANING

section and empty contents of dust bin.

Lid

Filter Screen

Primary Filter

Grasp filter screen, rotate counter-clockwise and lift out.

Grasp primary filter, rotate counter-clockwise and lift out.

Clean primary filter by gently tapping over a trash container.

CAUTION: Make sure dust bin is empty before

filter is removed.

CAUTION: Rinse with water only, do not use detergent or soap.

AAllllooww ffiilltteerr ttoo ddrryy 2244 hhoouurrss bbeeffoorree ppuuttttiinngg iitt

bbaacckk iinnttoo tthhee dduusstt bbiinn..

When the cleaning of the filter no longer restores vacuum cleaner suction to full power

you need to replace the filter.

Before replacing the primary filter it is a good idea to clean the inside of the dust bin and lid area.

Rotate filter clockwise until slots lock onto tabs in lid.

To re-install the filter screen, align tabs on filter screen with

tabs on lid.

Rotate filter screen clockwise to lock in place.

CAUTION:

When cleaning filter, do not use

brush or other similar tools that would damage

the filter itself.

Simply tap the filter on the edge of cap for normal dry cleaning.

For more thorough cleaning, rinse outside of filter with water and allow to dry thoroughly before reuse in vacuum cleaner.

- 10 -

CLEANING SECONDARY FILTER SCREEN

The secondary filter screen protects the motor.

Always check filter screen when cleaning dust bin.

If dirty or clogged, remove debris from filter screen.

Secondary

Filter Screen

EXHAUST FILTER MAINTENANCE

The exhaust filter removes dirt from recirculated air.

Check filter after emptying dust bin.

To remove, pull out on both sides of the exhaust filter cover.

Grasp the exhaust filter and pull out to remove.

EElleeccttrroossttaattiicc EExxhhaauusstt FFiilltteerr

When replacing or reinstalling the Electrostatic Filter, make

sure the gray side of the filter is facing the vacuum cleaner.

Reinstall exhaust filter cover by snapping into place.

IMPORTANT - Filter cannot be cleaned and should be

replaced at least once each year.

Exhaust

Filter Cover

Tabs

Electrostatic

Exhaust Filter

Panasonic MC-E4061 Operating instructions

Brand: Panasonic

Model: MC-E4061

Category: Vacuum cleaners

Type: Operating instructions

This manual is also suitable for

MCE4061

Download PDF

report

Panasonic MC-E4061 Operating instructions

This manual is also suitable for

Panasonic MC-E4061 Operating instructions

Related papers

Other documents