CHAUVET DJ Intimidator Spot Duo 150 User manual

CHAUVET DJ
Brand
CHAUVET DJ
Model
Intimidator Spot Duo 150
Category
Stroboscopes & disco lights
Type
User manual
User Manual
Page 2 of 27 Intimidator™ Spot Duo 150 User Manual Rev. 1
TABLE OF CONTENTS
1. Before You Begin .......................................................................................................... 4
What Is Included ............................................................................................................................... 4
Unpacking Instructions ..................................................................................................................... 4
Claims ....................................................................................................................................................... 4
Text Conventions ............................................................................................................................. 4
Symbols ............................................................................................................................................ 4
Disclaimer ......................................................................................................................................... 4
Product at a Glance .......................................................................................................................... 5
Safety Notes ..................................................................................................................................... 5
2. Introduction ................................................................................................................... 6
Overview ........................................................................................................................................... 6
Dimensions ....................................................................................................................................... 7
3. Setup .............................................................................................................................. 8
AC Power ......................................................................................................................................... 8
Fuse Replacement ........................................................................................................................... 8
Power Linking ............................................................................................................................................ 8
Mounting ........................................................................................................................................... 9
Orientation ................................................................................................................................................. 9
Rigging ...................................................................................................................................................... 9
4. Operation ......................................................................................................................10
Control Panel Operation ................................................................................................................. 10
Menu Map ....................................................................................................................................... 10
Configuration (DMX) ....................................................................................................................... 11
Starting Address ...................................................................................................................................... 11
DMX Personalities ................................................................................................................................... 11
DMX Channel Modes, Assignments, and Values .......................................................................... 12
20CH ....................................................................................................................................................... 12
20CH (cont.) ............................................................................................................................................ 13
20CH (cont.) ............................................................................................................................................ 14
20CH (cont.) ............................................................................................................................................ 15
17CH ....................................................................................................................................................... 16
17CH (cont.) ............................................................................................................................................ 17
17CH (cont.) ............................................................................................................................................ 18
10CH ....................................................................................................................................................... 19
10CH (cont.) ............................................................................................................................................ 20
Configuration (Standalone) ............................................................................................................ 21
Sound-Active Mode ................................................................................................................................. 21
Sound Sensitivity ..................................................................................................................................... 21
Automatic Mode ....................................................................................................................................... 21
Pan Operation ......................................................................................................................................... 22
Tilt Operation ........................................................................................................................................... 22
Pan/Tilt Angle Range ............................................................................................................................... 22
Display ..................................................................................................................................................... 22
Reset Software ........................................................................................................................................ 22
Load Factory Defaults ............................................................................................................................. 22
Master Auto Programs ............................................................................................................................. 23
Master Auto ............................................................................................................................................. 23
4-Head Program ...................................................................................................................................... 23
Master Auto ............................................................................................................................................. 23
2-Head Program ...................................................................................................................................... 23
5. Technical Information ..................................................................................................24
Intimidator™ Spot Duo 150 User Manual Rev. 1 Page 3 of 27
Product Maintenance ..................................................................................................................... 24
6. Technical Specifications ..............................................................................................25
Returns ........................................................................................................................................... 26
Contact Us ........................................................................................................................27
Page 4 of 27 Intimidator™ Spot Duo 150 User Manual Rev. 1
1. BEFORE YOU BEGIN
What Is
Included
• Intimidator™ Spot Duo 150
• Hanging Bracket with Mounting
Hardware
• Power Cord
• Warranty Card
• Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately
and check the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and
included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet.
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as missing com
ponents or parts, damage not related to shipping,
or concealed damage, file a claim with Chauvet within 7 days of delivery.
Text
Conventions
Convention Meaning
1—512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this document are subject to change
without notice. Chauvet assumes no responsibility or liability for any
errors or omissions
that may appear in this manual. Chauvet reserves the right to update the existing
document or to create a new document to correct any errors or omissions.
You can download the latest version of this document from www.chauvetlighting.com.
© Copyright 2015 Chauvet. All rights reserved.
Electronically published by Chauvet in the United States of America.
Author Date Editor Updated
R. Isenstadt 02/03/15 A. Leon 02/03/15
Intimidator™ Spot Duo 150 User Manual Rev. 1 Page 5 of 27
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Active
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
Please read the following Safety Notes carefully before working with the
product. The
Notes include important safety information about installation, usage, and maintenance.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Always disconnect the product from the power source before cleaning or replacing
the fuse.
• Avoid direct eye exposure to the light source while the product is on.
• Make sure the power cord is not crimped or damaged.
• Never disconnect the product from power cord by pulling or tugging on the cord.
• If mounting the product overhead, make sure there is adequate support for the
product’s weight, and always secure to a fastening device using a safety cable.
• Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
• The product is not intended for permanent installation.
• Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
• The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
• Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
• Be sure that no ventilation slots on the product’s housing are blocked.
• Never connect the product to a dimmer or rheostat.
• Make sure to replace the fuse with another of the same type and rating.
• Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket.
• The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
• In the event of a serious operating problem, stop using the product immediately.
• Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Keep this User Manual for future use. If you sell the product to someone else, be sure
that they also receive this document.
Page 6 of 27 Intimidator™ Spot Duo 150 User Manual Rev. 1
2. INTRODUCTION
Overview
Back Panel View
Front Panel View
Power In
Fuse
Holder
In/Out
Power Out
Cooling Fan
Safety
Loop
Tripod Adjustment
Knob
Microphone
Digital Display
Moving
Yokes
Focusing
Lenses
Menu
Buttons
Intimidator™ Spot Duo 150 User Manual Rev. 1 Page 7 of 27
Dimensions
546 mm
179 mm
11.4 in
290 mm
Page 8 of 27 Intimidator™ Spot Duo 150 User Manual Rev. 1
3. SETUP
AC Power
The Intimidator™ Spot Duo 150 has an auto-
ranging power supply and it can work with
an input voltage range of 100 to 240 VAC, 50/60 Hz.
To determine the product’s power requirements (
circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product
’s back panel, or
refer to the product
’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit
(circuit breaker or fuse). Make
sure the product has
an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product to
a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse
Replacement
Disconnect the product from power before replacing the fuse.
1. Disconnect the product from power.
2. With a flat-head screwdriver, unscrew the fuse holder cap
from the housing.
3. Remove the blown fuse.
4. Replace with a fuse of the same type and rating.
5. Screw the fuse holder cap back in place and reconnect
power.
Always replace a blown fuse with another of the same type and rating.
Power Linking
The product provides power linking via
the Edison/IEC outlet located in the back of the
unit.
Power Linking
Diagram
You can power link up to 5 Intimidator™ Spot Duo 150 units on 120 VAC or up to 9
Intimidator™ Spot Duo 150 units on 230 VAC.
The power linking diagram shown above corresponds to the North American
version of the product ONLY! If using the product
in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
requirements may differ in your country or region.
1
st
Product
2
nd
Product
3
rd
Product
Additional
Products
Intimidator™ Spot Duo 150 User Manual Rev. 1 Page 9 of 27
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes.
Orientation
The Intimidator™ Spot Duo
may be mounted in any position; however, make sure
adequate ventilation is provided around the product.
Rigging
• Before deciding on a location, always make sure there is easy access to the product
for maintenance and programming.
• Make sure that the structure or surface onto which you are mounting the product
can support the product’s weight (see the Technical Specifications
).
• When mounting the product overhead, always use a safety cable (such as CH-05
from Chauvet). Mount the product securely to a rigging point, such as
an elevated
platform or a truss.
• When rigging the product onto a truss, you should use a mounting clamp of
appropriate weight capacity. The bracket has 13-mm holes, which are
appropriate
for this purpose.
• When power linking multiple products, you must
always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
• Only loosen or tighten the tripod adjustment knob manually. Using tools could
damage the knob.
• The rubber feet also serve as floor supports. When mounting the product
on the
floor, make sure that the product and cables are away from people and vehicles.
Mounting Diagram
When using only one mounting clamp with this fixture, you must use a clamp with a
captive bolt to prevent accidental loosening.
Tripod Insertion
Point
Hanging
Bracket
Rubber Feet
Mounting Clamps
(such as the CLP-15N from Chauvet)
Safety Cable
(such as CH-05 from Chauvet)
Page 10 of 27 Intimidator™ Spot Duo 150 User Manual Rev. 1
4. OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons
located underneath the
display.
Button Function
<MENU>
Exits from the current menu or function
<UP>
Navigates upwards through the menu list and increases the
numeric value when in a function
<DOWN>
Navigates downwards through the menu list and decreases the
numeric value when in a function
<ENTER>
Enables the currently displayed menu or sets the currently selected
value into the selected function
Menu Map
Modes Programming Levels Description
DMX Address d001–d512
Sets the DMX starting address
Automatic A-01–A-16
Automatic mode
Sound-Active Srun
Sound-Active mode
Slave
Son1
Slave operating mode 1
Son2
Slave operating mode 2
Sound Sensitivity S-01–S-99
Sound sensitivity control
Master Auto
M--4
Master built-in 4-head program
M--2
Master built-in 2-head program
Pan 1
PA1
Normal pan operation for head 1
rPA1
Reverse pan operation for head 1
Pan 2
PA2
Normal pan operation for head 2
rPA2
Reverse pan operation for head 2
Tilt 1
ti1
Normal tilt operation for head 1
rti1
Reverse tilt operation for head 1
Tilt 2
ti2
Normal tilt operation for head 2
rti2
Reverse tilt operation for head 2
Display
diS
Normal display
rdiS
Inverted display
Channel Mode
20CH
20-channel DMX personality
17CH
17-channel DMX personality
10CH
10-channel DMX personality
Pan Range
PA36
360° pan range
PA18
180° pan range
Tilt Range
ti27
270° tilt range
ti18
180° tilt range
ti 9
90° tilt range
Reset rESt
Resets product
Load LoAd
Loads factory defaults
Intimidator™ Spot Duo 150 User Manual Rev. 1 Page 11 of 27
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
socket on the product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you
choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The Intimidator™ Spot Duo 150 uses up to 20 DMX channels in its 20-channel DMX
mode, which defines the highest configurable address to 493.
If you are not familiar with the DMX protocol,
download the DMX Primer from
www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU> repeatedly until d001—d512 shows on the display.
2. Use <UP> or <DOWN> to select the starting address.
3. Press <ENTER>.
DMX
Personalities
The Intimidator™ Spot Duo 150 has three DMX personalities: a 10-
channel personality,
a 17-channel personality, and a 20-channel personality.
To choose a DMX personality, follow the steps below:
1. Press <MENU> repeatedly until 10CH, 17CH, or 20CH shows on the display.
2. Use <UP> or <DOWN> to select the personality.
3. Press <ENTER>.
Page 12 of 27 Intimidator™ Spot Duo 150 User Manual Rev. 1
DMX Channel Modes, Assignments, and Values
20CH
Channel Function Value Setting
1
Pan 1
000ó255
Pan 0–360° for head 1
2
Fine Pan 1
000ó255
Fine panning control for head 1
3
Tilt 1
000
ó
255
Tilt 0–270° for head 1
4
Fine Tilt 1
000ó255
Fine tilting control for head 1
5
Pan 2
000ó255
Pan 0–360° for head 2
6
Fine Pan 2
000ó255
Fine panning control for head 2
7
Tilt 2
000ó255
Tilt 0–270° for head 2
8
Fine Tilt 2
000ó255
Fine tilting control for head 2
9
Speed
000ó255
Pan/Tilt speed (fast to slow)
10
Color Wheel 1
(Head 1)
000ó005
White
006ó011
Yellow
012ó017
Magenta
018
ó
023
Green
024ó029
Red
030ó035
Cyan
036ó041
Orange
042ó047
Blue
048ó053
Light Green
054ó063
Amber
064ó069
White + Yellow
070ó075
Yellow + Magenta
076ó081
Magenta + Green
082ó087
Green + Red
088ó093
Red + Cyan
094ó099
Cyan + Orange
100ó105
Orange + Blue
106ó111
Blue + Light Green
112ó117
Light Green + Amber
118ó127
Amber + White
128ó191
Rainbow effect with increasing speed
192ó255
Reverse rainbow effect with increasing speed
Color Wheel
Intimidator™ Spot Duo 150 User Manual Rev. 1 Page 13 of 27
20CH
(cont.)
Channel Function Value Setting
11
Color Wheel 2
(Head 2)
000ó005
White
006ó011
Yellow
012ó017
Magenta
018ó023
Green
024ó029
Red
030ó035
Cyan
036ó041
Orange
042ó047
Blue
048
ó
053
Light Green
054ó063
Amber
064ó069
White + Yellow
070ó075
Yellow + Magenta
076ó081
Magenta + Green
082ó087
Green + Red
088ó093
Red + Cyan
094ó099
Cyan + Orange
100ó105
Orange + Blue
106
ó
111
Blue + Light Green
112ó117
Light Green + Amber
118ó127
Amber + White
128ó191
Rainbow effect with increasing speed
192ó255
Reverse rainbow effect with increasing speed
12
Gobo Wheel 1
(Head 1)
064ó073
Gobo 9 shake with increasing speed
074ó079
Gobo 8 shake with increasing speed
080
ó
085
Gobo 7 shake with increasing speed
086ó091
Gobo 6 shake with increasing speed
092ó097
Gobo 5 shake with increasing speed
098ó103
Gobo 4 shake with increasing speed
104ó109
Gobo 3 shake with increasing speed
110ó115
Gobo 2 shake with increasing speed
116ó121
Gobo 1 shake with increasing speed
122ó127
Open
128ó191
Cycle effect with increasing speed
192ó255
Reverse cycle effect with increasing speed
Page 14 of 27 Intimidator™ Spot Duo 150 User Manual Rev. 1
20CH
(cont.)
Channel Function Value Setting
13
Gobo Wheel 2
(Head 2)
064ó073
Gobo 9 shake with increasing speed
074ó079
Gobo 8 shake with increasing speed
080ó085
Gobo 7 shake with increasing speed
086ó091
Gobo 6 shake with increasing speed
092ó097
Gobo 5 shake with increasing speed
098ó103
Gobo 4 shake with increasing speed
104ó109
Gobo 3 shake with increasing speed
110ó115
Gobo 2 shake with increasing speed
116ó121
Gobo 1 shake with increasing speed
122ó127
Open
128ó191
Cycle effect with increasing speed
192
ó
255
Reverse cycle effect with increasing speed
14
Dimmer 1
000ó255
Dimmer for head 1 (0–100%)
15
Dimmer 2
000ó255
Dimmer for head 2 (0–100%)
16
Shutter 1
(Head 1)
000ó003
Light off
004ó007
Light on
008ó076
Shutter with increasing speed
077ó145
Pulse strobe
146ó215
Random strobe
216ó255
Light on
17
Shutter 2
(Head 2)
000ó003
Light off
004ó007
Light on
008ó076
Shutter with increasing speed
077ó145
Pulse strobe
146ó215
Random strobe
216ó255
Light on
Intimidator™ Spot Duo 150 User Manual Rev. 1 Page 15 of 27
20C
H
(cont.)
Channel
Function Value Setting
18 Control Functions
000ó009
No function
010ó014
Pan/Tilt blackout
015ó019
Color blackout
020ó024
Gobo blackout
025ó029
Pan/Tilt/Color blackout
030ó034
Pan/Tilt/Gobo blackout
035ó039
Color/Gobo blackout
040
ó
044
Pan/Tilt/Color/Gobo blackout
045ó049
No function
050ó054
First two heads setting
055ó059
Latter two heads setting
060ó064
Cancel four heads
065ó069
No function
070ó074
Reset
075ó079
No function
080ó084
Reverse pan/tilt for both heads
085ó089
Reverse pan for head 1
090ó094
Reverse pan for head 2
095ó099
Reverse tilt for head 1
100ó104
Reverse tilt for head 2
105ó109
Cancel reverse pan for head 1
110ó114
Cancel reverse pan for head 2
115ó119
Cancel reverse tilt for head 1
120ó124
Cancel reverse tilt for head 2
125ó129
Cancel reverse pan/tilt for both heads
130ó135
No function
136ó175
Strobe Pattern 1 with increasing
speed
When
Channel 19
is active
176ó215
Strobe Pattern 2 with increasing
speed
216ó255
Strobe Pattern 3 with increasing
speed
19 Movement Macros
000ó007
No function
008ó022
Movement macro 1
023ó037
Movement macro 2
038
ó
052
Movement macro 3
053ó067
Movement macro 4
068ó082
Movement macro 5
083ó097
Movement macro 6
098ó112
Movement macro 7
113
ó
127
Movement macro 8
128ó142
Movement macro 9
143ó157
Movement macro 10
158ó172
Movement macro 11
173ó187
Movement macro 12
188ó202
Movement macro 13
203ó217
Movement macro 14
218ó232
Movement macro 15
233ó247
Movement macro 1–15
248ó255
Sound-Active program
20
Movement Macro Speed
000
ó
255
Fast to slow
Page 16 of 27 Intimidator™ Spot Duo 150 User Manual Rev. 1
17CH
Channel Function Value Setting
1
Pan 1
000ó255
Pan 0–360° for head 1
2
Fine Pan 1
000ó255
Fine panning control for head 1
3
Tilt 1
000ó255
Tilt 0–270° for head 1
4
Fine Tilt 1
000ó255
Fine tilting control for head 1
5
Pan 2
000ó255
Pan 0–360° for head 2
6
Fine Pan 2
000ó255
Fine panning control for head 2
7
Tilt 2
000ó255
Tilt 0–270° for head 2
8
Fine Tilt 2
000
ó
255
Fine tilting control for head 2
9
Speed
000ó255
Pan/Tilt speed (fast to slow)
10
Color Wheel
(Both Heads)
000ó005
White
006ó011
Yellow
012ó017
Magenta
018ó023
Green
024ó029
Red
030ó035
Cyan
036ó041
Orange
042ó047
Blue
048ó053
Light Green
054ó063
Amber
064ó069
White + Yellow
070ó075
Yellow + Magenta
076ó081
Magenta + Green
082ó087
Green + Red
088ó093
Red + Cyan
094ó099
Cyan + Orange
100ó105
Orange + Blue
106ó111
Blue + Light Green
112ó117
Light Green + Amber
118
ó
127
Amber + White
128ó191
Rainbow effect with increasing speed
192ó255
Reverse rainbow effect with increasing speed
11
Gobo Wheel
(Both Heads)
064ó073
Gobo 9 shake with increasing speed
074ó079
Gobo 8 shake with increasing speed
080ó085
Gobo 7 shake with increasing speed
086ó091
Gobo 6 shake with increasing speed
092ó097
Gobo 5 shake with increasing speed
098ó103
Gobo 4 shake with increasing speed
104ó109
Gobo 3 shake with increasing speed
110ó115
Gobo 2 shake with increasing speed
116ó121
Gobo 1 shake with increasing speed
122
ó
127
Open
128ó191
Cycle effect with increasing speed
192ó255
Reverse cycle effect with increasing speed
Intimidator™ Spot Duo 150 User Manual Rev. 1 Page 17 of 27
17CH
(cont.)
Channel Function Value Setting
12
Dimmer 1
000ó255
Dimmer for head 1 (0–100%)
13
Dimmer 2
000ó255
Dimmer for head 2 (0–100%)
14
Shutter
(Both Heads)
000ó003
Light off
004ó007
Light on
008ó076
Shutter with increasing speed
077ó145
Pulse strobe
146ó215
Random strobe
216
ó
255
Light on
15 Control Functions
000ó009
No function
010ó014
Pan/Tilt blackout
015ó019
Color blackout
020ó024
Gobo blackout
025ó029
Pan/Tilt/Color blackout
030ó034
Pan/Tilt/Gobo blackout
035ó039
Color/Gobo blackout
040ó044
Pan/Tilt/Color/Gobo blackout
045ó049
No function
050ó054
First two heads setting
055ó059
Latter two heads setting
060ó064
Cancel four heads
065ó069
No function
070ó074
Reset
075ó079
No function
080ó084
Reverse pan/tilt for both heads
085ó089
Reverse pan for head 1
090ó094
Reverse pan for head 2
095ó099
Reverse tilt for head 1
100ó104
Reverse tilt for head 2
105
ó
109
Cancel reverse pan for head 1
110ó114
Cancel reverse pan for head 2
115ó119
Cancel reverse tilt for head 1
120ó124
Cancel reverse tilt for head 2
125ó129
Cancel reverse pan/tilt for both heads
130ó135
No function
136ó175
Strobe Pattern 1 with increasing
speed
When
Channel 16
is active
176ó215
Strobe Pattern 2 with increasing
speed
216ó255
Strobe Pattern 3 with increasing
speed
Page 18 of 27 Intimidator™ Spot Duo 150 User Manual Rev. 1
17CH
(cont.)
Channel Function Value Setting
16 Movement Macros
000ó007
No function
008ó022
Movement macro 1
023ó037
Movement macro 2
038ó052
Movement macro 3
053ó067
Movement macro 4
068ó082
Movement macro 5
083ó097
Movement macro 6
098
ó
112
Movement macro 7
113ó127
Movement macro 8
128ó142
Movement macro 9
143ó157
Movement macro 10
158ó172
Movement macro 11
173ó187
Movement macro 12
188ó202
Movement macro 13
203ó217
Movement macro 14
218ó232
Movement macro 15
233ó247
Movement macro 1–15
248ó255
Sound-Active program
17
Movement Macro Speed
000ó255
Fast to slow
Intimidator™ Spot Duo 150 User Manual Rev. 1 Page 19 of 27
10CH
Channel
Function Value Setting
1
Pan
000ó255
Pan 0–360° for both heads
2
Tilt
000ó255
Tilt 0–270° for both heads
3
Color Wheel
(Both Heads)
000ó005
White
006ó011
Yellow
012ó017
Magenta
018ó023
Green
024ó029
Red
030ó035
Cyan
036ó041
Orange
042ó047
Blue
048ó053
Light Green
054ó063
Amber
064ó069
White + Yellow
070ó075
Yellow + Magenta
076ó081
Magenta + Green
082ó087
Green + Red
088ó093
Red + Cyan
094ó099
Cyan + Orange
100
ó
105
Orange + Blue
106ó111
Blue + Light Green
112ó117
Light Green + Amber
118ó127
Amber + White
128ó191
Rainbow effect with increasing speed
192ó255
Reverse rainbow effect with increasing speed
4
Gobo Wheel
(Both Heads)
064ó073
Gobo 9 shake with increasing speed
074ó079
Gobo 8 shake with increasing speed
080
ó
085
Gobo 7 shake with increasing speed
086ó091
Gobo 6 shake with increasing speed
092ó097
Gobo 5 shake with increasing speed
098ó103
Gobo 4 shake with increasing speed
104ó109
Gobo 3 shake with increasing speed
110ó115
Gobo 2 shake with increasing speed
116ó121
Gobo 1 shake with increasing speed
122ó127
Open
128ó191
Cycle effect with increasing speed
192ó255
Reverse cycle effect with increasing speed
5
Dimmer 1
000ó255
Dimmer for head 1 (0–100%)
6
Dimmer 2
000
ó
255
Dimmer for head 2 (0–100%)
7
Shutter
(Both Heads)
000ó003
Light off
004ó007
Light on
008ó076
Shutter with increasing speed
077ó145
Pulse strobe
146
ó
215
Random strobe
216ó255
Light on
Page 20 of 27 Intimidator™ Spot Duo 150 User Manual Rev. 1
10CH
(cont.)
Channel
Function Value Setting
8 Control Functions
000ó009
No function
010ó014
Pan/Tilt blackout
015ó019
Color blackout
020ó024
Gobo blackout
025ó029
Pan/Tilt/Color blackout
030ó034
Pan/Tilt/Gobo blackout
035ó039
Color/Gobo blackout
040ó044
Pan/Tilt/Color/Gobo blackout
045
ó
049
No function
050ó054
First two heads setting
055ó059
Latter two heads setting
060ó064
Cancel four heads
065ó069
No function
070ó074
Reset
075ó079
No function
080ó084
Reverse pan/tilt for both heads
085ó089
Reverse pan for head 1
090
ó
094
Reverse pan for head 2
095ó099
Reverse tilt for head 1
100ó104
Reverse tilt for head 2
105ó109
Cancel reverse pan for head 1
110ó114
Cancel reverse pan for head 2
115ó119
Cancel reverse tilt for head 1
120ó124
Cancel reverse tilt for head 2
125ó129
Cancel reverse pan/tilt for both heads
130ó135
No function
136ó175
Strobe Pattern 1 with increasing
speed
When
Channel 9
is active
176ó215
Strobe Pattern 2 with increasing
speed
216ó255
Strobe Pattern 3 with increasing
speed
9 Movement Macros
000ó007
No function
008ó022
Movement macro 1
023ó037
Movement macro 2
038ó052
Movement macro 3
053ó067
Movement macro 4
068ó082
Movement macro 5
083ó097
Movement macro 6
098ó112
Movement macro 7
113ó127
Movement macro 8
128ó142
Movement macro 9
143ó157
Movement macro 10
158ó172
Movement macro 11
173ó187
Movement macro 12
188ó202
Movement macro 13
203ó217
Movement macro 14
218ó232
Movement macro 15
233ó247
Movement macro 1–15
248ó255
Sound-Active program
10
Movement Macro Speed
000
ó
255
Fast to slow
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27

CHAUVET DJ Intimidator Spot Duo 150 User manual

CHAUVET DJ
Brand
CHAUVET DJ
Model
Intimidator Spot Duo 150
Category
Stroboscopes & disco lights
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents