SUHLQVWDOOHG
UHTXLUHGWRLQVWDOO$.
LIUHTXLUHGE\ORFDOFRGHV
Suction Cup (1)
M4 x 1” (4)
Safety Grille
Screws (2)
M4 x 1-1/2” (4)
Wire Caps (3)
7” Round transition adapter
(pre-installed on top of hood)
3-1/4”x10” rectangular cover plate
(pre-installed on back of hood)
3-1/4”x10” rectangular vertical
transition adapter
3-1/4”x10” rectangular
starting collar
Duct pieces
To t a l
Equivalent number
length x used =
3-1/ 4” x 10”
Rect.,
straight
1 Ft. x ( ) =
Ft.
7”-10” Round,
straight
1 Ft. x ( ) =
Ft.
3-1/ 4” x 10”
Rect.90
0
elbow
15 Ft. x ( ) =
Ft.
3-1/ 4” x 10”
Rect.45
0
elbow
9 Ft. x ( ) =
Ft.
3-1/ 4” x 10”
Rect.90
0
flat elbow
24 Ft. x ( ) =
Ft.
3-1/ 4” x 10”
Rect.
wall cap
with damper
30 Ft. x ( ) =
Ft.
3-1/ 4” x 10”
Rect.to
6” round
transition
5 Ft. x ( ) =
Ft.
3-1/ 4” x 10”
Rect.to
6” round
transition
90
0
elbow
20 Ft. x ( ) =
Ft.
6” Round,
90
0
elbow
15 Ft. x ( ) =
Ft.
6” Round,
45
0
elbow
9 Ft. x ( ) =
Ft.
Ft.
6” Round,
straight
1 Ft. x ( ) =
Ft.
Subtotal column 1 =
Duct pieces
To t a l
Equivalent number
length x used =
6” Round
wall cap
with damper
30 Ft. x ( ) =
Ft.
Round
wall cap
with damper
30 Ft. x ( ) =
Ft.
7” - 10”
Round,
90
0
elbow
15 Ft. x ( ) =
Ft.
7” - 10”
7” - 10”
Round,
45
0
elbow
9 Ft. x ( ) =
Ft.
Ft.
Ft.
Ft.
6” Round,
roof cap
30 Ft. x ( ) =
Ft.
7” - 10”
Round,
roof cap
30 Ft. x ( ) =
Ft.
Subtotal column 2 =
Subtotal column 1 =
Total ductwork =
6” round to
3-1/ 4” x 10”
rect.
transition
1 Ft. x ( ) =
Ft.
6” round to
3-1/ 4” x 10”
rect.
transition
90
0
elbow
16 Ft. x ( ) =
Ft.
7” round to
3 1/ 4” x 10”
rect.
transition
8 Ft. x ( ) =
Ft.
7” round to
3-1/ 4” x 10”
rect.
transition
90
0
elbow
23 Ft. x ( ) =
Ft.
7-3/4"
36"
Min 24” - Max 32"
side wall cap
w/gravity damper
cabinet
cabinet
soffit or crawl space
side wall cap
w/gravity damper
3-1/4”x10” rear
ducting w/side
wall gravity damper
roof pitch w/
flashing & cap
3 1/16”
1
7/16”
9 15/16”
(30”) 28
1/16”, (36”) 34”
(42”) 39
3/4
”, (48“) 45
3/4
”
5 1/16”
2
3/4”
8
5/8”
(30”) 11 5/16”, (36”) 12 1/2”
(42”) 12
1/2”, (48“) 12 1/2”
1 15/16”
elec
k/o
(30”) 29 3/4”, (36”) 35 3/4”
(42”) 41
3/4”, (48“) 47 11/16”
(30”) 14”, (36”) 17”
(42”) 19
7/8”, (48“) 22 7/8”
C/L
13
9/16”
21
1/8”
7 7/8”
1
3/8”
9 15/16”
1 1/16”
(30”) 11 5/16”
(36”) 12
1/2”
(42”) 12
1/2”
(48“) 12
1/2”
C/L
3 1/16”
6 7/8”
6
7/8
”
elec
k/o
TOP
SIDE
FRONT BACK
Cable Lock
bottom panel &
lighting harness
wood blocking
installation screws
and key-holes
duct work
residue cups &
safety grilles
electrical
duct tape
(G) Indicator: indicates level of blower speed from 1 to 6
Blower Speed 1 (LOW): Indicator flashing
Blower Speed 2: Indicator lit
Blower Speed 3: Indicator flashing
Blower Speed 4: Indicator lit
Blower Speed 5: Indicator flashing
Blower Speed 6 (HIGH): Indicator lit
(A) Power hood on/off
(B) Adjust to higher blower speed (1 to 6)
(C) Adjust to lower blower speed (6 to 1)
(D) Power lights on/off and dim (night light)
(E) Timer that powers off hood in 5 or 10 minutes
(F) Indicates 5 or 10 minute delay when lit
(A) (C) (B) (E) (D)
(F)
Blower Controls
Power on the blowers by pressing “ON/OFF” once.
Adjust blower speed (1 - 6) by pressing
“HIGH” or “LOW”.
Speed Indicator
The speed indicator will show the speed the
blowers are operating at as follows:
Note: The controls are equipped with a blower
speed setting memory module. When powering
on the blowers, the speed level will start at the
speed setting last memorized.
Blower Speed 1 (LOW): Indicator flashing
Blower Speed 2: Indicator lit
Blower Speed 3: Indicator flashing
Blower Speed 4: Indicator lit
Blower Speed 5: Indicator flashing
Blower Speed 6 (HIGH): Indicator lit
ON/OFF
LOW HIGH
Power off blowers by pressing “ON/OFF” again.
Lights Controls
Power on halogen lights by pressing “LIGHT”.
Press 2nd time to dim.
Press again to turn lights off.
ON/OFF
LIGHT
DELAY OFF
Timed Delay Off
Press “DELAY OFF” once to power hood
down in 5 minutes. (blowers and lights)
Indicator “5” will illuminate.
Press “DELAY OFF” twoce to power hood
down in 10 minutes. (blowers and lights)
Indicator “10” will illuminate.
Indicator
LOW HIGH
DELAY OFF
SELF CLEAING FEATURE
Zephyr Typhoon hoods are filter-less with a self cleaning feature. The centrifugal blower system
automatically liquifies cooking residue in its internal housing. All hoods are equipped with dish-
washer safe residue cups to collect cooking residue during the self cleaning function.
Cooking residue are often automatically liquified and can accumulate in the residue cups from
everyday use. Neverthless, grease fromc ooking could also dry and adhere the internal housing.
Running the self clean function periodically will flush out accumulated residue in the range hood’s
internal housing.
CLEANING FREQUENCY
Cleaning should be performed approximately once a month under normal usage of 1 hour per day.
The hood may need to be cleaned more often if you cook heavily.
DETERGENT
Use a grease cutting detergent such as Simple Green or 409.
WARNING
Use extreme caution while cleaning the hood when safety grilles are removed. Beware of
blowers catching on to hair, loose clothing and fingers. NEVER leave children unattended.
1) Remove safety grilles by removing the Philips
head screw securing each grille to the hood body.
2) Power on blowers at Speed 1 and set timed
Delay Off to “5” minutes.
3) With nozzle on “spray”, squirt grease cutting
detergent onto blower wheel blades 30 - 35 times.
Repeat for each blower. Detergent will collect in
the residue cups.
4) Remove residue cups. Clean residue cups and
safety grilles in dishwaser or clean by hand. Replace
residue cups and safety grilles after cleaning.
CLEANING INSTRUCTIONS
Page is loading ...
/