MODWAY EEI-3027-BLK-BLK Operating instructions

Brand
MODWAY
Model
EEI-3027-BLK-BLK
Type
Operating instructions

This manual is also suitable for

EEI –3027 ROCKING CHAIR
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 1 of 4
Thank you for purchasing the MODWAY ROCKING CHAIR！
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2. Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6. Please keep all fitting out of reach of children.
Hardware:
A. Bolt M6x35mm x 3
B. Bolt M6x25mm x 4
C. Bolt M6x15mm x 8
D. Flat Washer x 15
E. Nut x 3
F. Allen Wrench x 1
G. Wrench x 1
Component:
1 Mesh with Frame x 1 2 Left Arm x 1 3 Right Arm x 1 4 Rail x 2
1
2
3
4
4
EEI –3027 ROCKING CHAIR
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 2 of 4
STEP 1:
Please open Mesh with Frame (1) and put on a carpeted or padded surface.
Insert 3 pieces of Bolts (A) with 3 pieces of Flat Washers (D) into the top holes on the back frame of Mesh with
Frame (1) as shown.
Then insert 3 pieces of Nuts (E) into the Bolts (A), tighten Bolts (A) by using Allen Wrench (F) and Wrench (G)
as shown.
Hardware & Tools required
STEP 2:
Attach 2 pieces of Rails (4) to the bottom of back frame of Mesh with Frame (1) by using 4 pieces of Bolts (B)
with 4 pieces of Flat Washers (D) as shown. Tighten Bolts (B) by using Allen Wrench (F) as shown.
Hardware & Tools required
1
1
E
G
A
D
F
FRONT
A
x 3
x 3
D
E
x 3
x 1
x 1
G
FRONT
4
4
B
F
D
B
x 4
x 4
D
x 1
F
EEI –3027 ROCKING CHAIR
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 3 of 4
STEP 3:
Insert Left Arm (2) into the pre-drilled holes on Rails (4) as shown.
STEP 4:
Insert 4 pieces of Bolt (C) with 4 pieces of Flat Washers (D) into the pre-drilled holes on Rails (4).
Tighten Bolts (C) by using Allen Wrench (F) as shown
Hardware & Tools required
F
R
O
N
T
2
2
4
4
4
1
C
x 4
x 4
D
x 1
F
FRO
N
T
4
4
1
C
F
D
EEI –3027 ROCKING CHAIR
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 4 of 4
STEP 5:
Attach Right Arm (3) into the pre-drilled holes on Rail (4) then insert 4 pieces of Bolts (C) with 4 pieces of Flat
Washers (D) as shown. Tighten Bolts (C) by using Allen Wrench (F) as shown.
Hardware & Tools required
STEP 6:
Carefully turn over the assembled rocking chair.
Assembly is complete. Your rocking chair is ready to be used now!
FRON
T
3
1
C
F
D
C
x 4
x 4
D
x 1
F
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

MODWAY EEI-3027-BLK-BLK Operating instructions

Brand
MODWAY
Model
EEI-3027-BLK-BLK
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents